LG LFXS24566S/00 Le manuel du propriétaire

Marque: LG

Modèle: LFXS24566S/00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Life's Good

FRENCH DOOR

REFRIGERATOR

Please read this owneCs manual thoroughly before

operating and keep it handy for reference at al times

LFXS24566 _

P/No°:MFL63264296

2 TABLE OF CONTENTS

TABLE OF CONTENTS

3 PRODUCT FEATURES

4 IMPORTANT SAFETY

INSTRUCTIONS

7 COMPONENTS

7 Refrigerator Exterior

8 Refrigerator Interior

INSTALLATION9

9 Installation Overview

10 Specifications

11 Unpacking Your Refrigerator

11 Choosing the Proper Location

11 - Flooring

12 - Ambient Temperature

12 - Measuring the Clearances

12 Removing/Assembling the Refrigerator

Door Handles

13 Removing/Assembling the Freezer

Drawer Handle

13 Removing/Assembling the Doors and

Drawers

13 - Removing the Left Refrigerator Door

14 - Removing the Right Refrigerator Door

15 - Assembling the Right Refrigerator Door

15 - Assembling the Left Refrigerator Door

16 - Removing the Freezer Drawers

17 - Assembling the Freezer Drawers

19 Connecting the Water Line

19 - Before You Begin

19 -Water Pressure

19 -What You Witl Need

20 - Water Line Installation Instructions

22 Turning On the Power

23 Leveling and Door Alignment

23 - Leveling

23 - Door Alignment

24 HOWTOUSE

24 Before Use

25 Control Panel

25 - Control Panet Features

27 In-Door Ice Bin

27 - Detaching the In-Door ice Bin

27 - Assembling the In-Door ice Bin

28 Automatic Icemaker

28 - Turning the Automatic Icemaker On or

Off

29 - When You Should Turn the Icemaker Off

29 - Normal Sounds You May Hear

29 - Preparing for Vacation

30 Ice and Water Dispenser

30 - Dispenser

30 - Using the Dispenser

30 - Locking the Dispenser

30 - Cleaning the Dispenser Stand

31 Storing Food

31 - Food Preservation Location

32 - Food Storage Tips

32 - Storing Frozen Food

33 Humidity Controlled Crisper

34 Detaching and Assembling the Storage

Bins

35 Door-in -Door

37 Adjusting the Refrigerator Shelves

38 MAINTENANCE

38 Cleaning

39 Replacing the Water Filter

41 SMART DIAGNOSIS

41 Using Smart Diagnosis

42 TROUBLESHOOTING

52 WARRANTY

PRODUCT FEATURES 3

PRODUCT FEATURES

* Depending on the model, some of the following functions may not be available.

FILTERED WATER AND ICE DISPENSER

The water dispenser dispenses fresh, chilled water.

The ice dispenser dispenses cubed and crushed ice.

DOOR ALARM

The Door Alarm function is designed to prevent refrigerator malfunctioning

that could occur if a refrigerator door or freezer drawer remains open. If a

refrigerator door or freezer drawer is left open for more than 60 seconds, a

warning alarm sounds in 30 second intervals.

HUMIDITY CONTROLLED CRISPER

The Humidity Controlled Crisper is designed to help keep your fruits and

vegetables fresh and crisp. You can control the amount of humidity in the

crisper by adjusting the setting between Low and High.

GLIDE'N'SERVE

Glide'N'Serve provides storage space that keeps the compartment colder

than the refrigerator.

It is a convenient place to store sandwiches or meat to be cooked.

ICE PLUS

Ice production can be increased by approximately 20 percent when the

freezer section is maintained at the coldest temperature for a 24-hour

period.

4 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

This guide contains many important safety messages. Aiways read and obey atl safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of

hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard

signal word WARNING or CAUTION. These words mean:

_I_WARNING You can be killed or seriously injured if you do not follow instructions.

,_, CAUT!ON Indicates an imminently hazardous situation which, if not avoided, may result

in minor or moderate injury, or product damage.

WARNING

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following.

Power

• NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and

pull it straight out from the outlet.

• Immediately repair or replace atl power cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length or at

either the plug or connector end.

• Do not use an uncertified power outlet.

Unplug the power plug immediately in the event of a blackout or thunderstorm.

• Plug in the power plug with the power cord facing downward.

Installation

. Contact an authorized service center when you install or relocate the refrigerator.

° When moving your refrigerator away from the wall, be careful not to roll over or damage the

power cord.

• Connect this product to a dedicated grounded electric outlet conforming with the rating prior

to use. It is the user's responsibility to replace a standard 2-prong wall outlet with a standard

3-prong wall outlet.

• Do not install the refrigerator where there may be a danger of falling.

Use

• DO NOT allow children to climb, stand, or hang on the refrigerator doors or shelves in the

refrigerator. They could damage the refrigerator and seriously injure themselves.

Do not place heavy objects on the dispenser of the refrigerator or hang onto it.

° Do not place heavy or dangerous objects (bottles with liquid) on the refrigerator.

Do not put live animals inside of the refrigerator.

• Do not allow children to climb into the product when it is in use.

In the event of a gas teak (propane/LPG), ventilate sufficiently and contact an authorized

service center before use. Do not touch or disassemble the electric outlet of the refrigerator.

In the event of a refrigerant leak, move flammable objects away from the refrigerator.

Ventilate sufficiently and contact an authorized service center.

Do not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the

refrigerator or store them inside the refrigerator. Do not place the refrigerator in the vicinity

of flammable gas.

_kWARNING :This product contains chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

IMPORTANT SAFETY INSTRUCTIONS 5

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following.

• Do not use this product for special purposes (storage of medicine or test materials or for ships,

etc).

, Unplug the power plug before cleaning or repairing the refrigerator.

• When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.

• Do not modify or extend the power cord.

Do not use a dryer to dry the interior. Do not light a candle to remove the interior odor.

• For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit

checked by a qualified electrician to make sure the outlet is properly grounded.

• Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the

user's responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.

Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect

smoke.

• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

• Do not disassemble or modify the refrigerator.

° Do not put hands, feet, or metal objects below or behind the refrigerator.

• Do not operate the refrigerator or touch the power cord with wet hands.

• In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector

mechanism or with the heating element that releases the cubes. Do not place fingers or hands

on the automatic ice-making mechanism while the refrigerator is plugged in.

• When dispensing ice from the dispenser, do not use crystal ceramics.

° Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your

refrigerator is in operation.

° Do not put glass containers, glass bottles or soda in the freezer.

° This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning the use of the appliance by a person responsible for their

safety.

Do not refreeze frozen food that have thawed completely. It may result in a serious health issue.

• If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper

disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in

accordance with the relevant environmental law.

° Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days.

When disposing the refrigerator, remove the packing materials from the door or take off the

doors but leave the shelves in place so that children may not easily climb inside.

6 IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following,

,_ CAUTION

Installation

• The refrigerator must be properly installed in accordance with the Installer Instructions that

were taped to the front of the refrigerator.

• Be careful when you unpack and install the refrigerator. Immediately dispose of packing

materials (plastic) out of reach of children.

Use

• Close the door carefully when children are around.

• Keep fingers out of pinch point areas; clearances between the doors and cabinets are

necessarily small. Be careful closing doors when children are in the area,

If you store food properly, beware that it may fall and cause injury.

Maintenance

• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft fabric.

• Wipe foreign objects (dust, water, etc) off the prongs of the power plug and contact areas

regularly.

Supply Cord Replacement

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

or a similarly qualified person in order to avoid a hazard.

SAVE THESE INSTUCTIONS

COMPONENTS 7

COMPONENTS

Use this page to become more familiar with the parts and features of your refrigerator.

Page references are included for your convenience.

*The appearance and specifications of the actual product may differ depending on the model.

Refrigerafor Exferior

LED Display

Displays the refrigerator and

freezer temperature, the water

filter condition and the dispenser

status.

Ice Plus

When this feature is activated,

the freezer section win run at the

coldest temperature for a 24-hour

period to increase ice production.

Door Alarm

A warning alarm sounds at 30-

second intervals when the

refrigerator or freezer door is left

open for more than 60 seconds,

Button

Filtered Water and

Ice Dispenser

Dispenses fresh, chilled,

filtered water through

the door. The ice

dispenser offers cubed

or crushed ice.

8 COMPONENTS

Refrigerafor interior

LED inferior Lamps

The interior lamps light up the

inside of the refrigerator.

Wafer Filter

SpacePlus Ice System --

Automatically produces

80-130 ice cubes in a

24-hour period.

Fixed Door Bins

Mullion

Folds in when the

left door is opened.

-- Smart Diagnosis Speaker

Hold your phone to this speaker when

activating Smart Diagnosis. Refer to the

Smart Diagnosis section for more details,

-- Door-In-Door Case

Cheese & Buffer Bin

This makes spreading butter and

_II slicing cheese easier,

Can Storage Bin

Used

to preserve chilled

food or drinks. _

Glide'N'Serve --

Allows you to store food items n

at a different temperature than

the regular refrigerator area. L_.

Auto Closing Hinge J

The refrigerator doors

and freezer drawers close

automatically when you push

them slightly.

(The door only closes

automatically when it is open

at an angle of less than 30°.)

Durabase

-- Durabase Divider

Refrigerator Shelves

The shelves in your

refrigerator are adjustable

to meet your individual

storage needs,

Condiment Bin

Crispers

Controls humidity and

helps vegetables and

fruit to stay crisp.

Pullout Drawer

INSTALLATION9

INSTALLATION

Insfallafion Overview

Please read the following installation instructions first after purchasing this product or transporting

it to another location.

-.,.

1 Unpacking your

refrigerator

Choosing the proper

location

3 Disassembling/Assembling

4 Connecting the water 5 Leveling and Door

supply and water line Alignment

10 INSTALLATION

Specifications

The appearance and specifications listed in this manual may vary due to constant product

improvements.

Description French door refrigerator

Electrical requirements 115 VAC @ 60 Hz

Min. / Max. Water pressure 20 and 120 psi (140 and 830 kPa)

Dimensions 35 3/4" (W) X 34 1/4" {D) X 69 3/4" (H), 46 1/2" (D w/door open)

908mm(W) X869,95mm(D)X 1 771,65 (H), 1 181.1 mm(Dw/door

open)

Net weight 315 lb. (143kg)

INSTALLATION11

Unpacking Your Re{rigerafor

"-//_ WARNING

• Use two or more people to move and

install the refrigerator. Failure to do so

can result in back or other injury.

Your refrigerator is heavy. When moving

the refrigerator for cleaning or service,

be sure to protect the floor. Always pull

the refrigerator straight out when moving

it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage

could occur.

Keep flammable materials and vapors,

such as gasoline, away from the

refrigerator. Failure to do so can result in

fire, explosion, or death.

Remove tape and any temporary labels from your

refrigerator before using. Do not remove any

warning-type labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue residue

can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with

your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

Refrigerator shelves are installed in the shipping

position. Please reinstall shelves according to

your individual storage needs.

Choosing fhe Proper Locafion

• Select a place where a water supply can

be easily connected for the automatic

icemaker.

@ NOTE /

The water pressure must be between 20

and 120 psi (140 and 830 kPa)on models

without a water filter and between 40 and

120 psi (280 and 830kPa) on models with

The refrigerator should always be plugged

into its own individual properly grounded

electrical outlet rated for 115 Volts, 60 Hz,

AC only, and fused at 15 or 20 amperes.

This provides the best performance

and also prevents overloading house

wiring circuits which could cause a fire

hazard from overheated wires. It is

recommended that a separate circuit

serving only this appliance be provided.

TA WARNING

o reduce the risk of electric shock, do not

install the refrigerator in a wet or damp

area j

Flooring

To avoid noise and vibration, the unit must be

leveled and installed on a solidly constructed

floor. If required, adjust the leveling legs to

compensate for unevenness of the floor. The

front should be slightly higher than the rear to

aid in door closing. Leveling legs can be turned

easily by tipping the cabinet slightly. Turn the

leveling legs to the left to raise the unit or to

the right to lower it. (See Leveling and door

Alignment.)

@ NOTE

Installing on carpeting, soft tile surfaces

a platform or weakly supported structun

12 INSTALLATION

Ambient Temperature

Install this appliance in an area where the

temperature is between 55°F (13°C) and 110°F

(43°C), If the temperature around the appliance

is too low or high, cooling ability may be

adversely affected.

Measuring the Clearances

Too small of a distance from adjacent items

may result in lowered freezing capability and

increased electricity consumption charges.

Allow at least 24 inches (61 cm) in front of the

refrigerator to open the doors, and at least

2 inches (5.08 cm) between the back of the

refrigerator and the wall.

24" (61 cm)

-,_ 2" (5.08cm)

Removing/Assembling the

Refrigerator Door Handles

-_@ NOTE

Removing the doors is always

recommended when it is necessary to

move the refrigerator through a narrow

opening. If it is necessary to remove the

Removing fhe Handles

Loosen the set screws D with a 3/s2in.

Allen wrench and remove the handle.

Loosen the mounting fasteners [] that

connect to the refrigerator door and handle

using a 4/4in. Allen wrench, remove the

mounting fasteners.

Assembling fhe Handles

1 Assemble the mounting fasteners D at

both ends of the handle using a _/4in.

Allen wrench,

Place the handle on the door by fitting

the handle footprints over the mounting

fasteners and tightening the set screws []

with a s/s2in, Allen wrench,

INSTALLATION 13

Removing/Assembling fhe

Freezer Drawer Handle

Removing fhe Handles

1 Loosen the set screws In located on the

lower side of the handle with a _/8in. Alien

wrench and remove the handle,

Loosen the mounting fasteners _ that

connect to the

freezer drawer

and handle

using a _/4in,

Allen wrench,

and remove

the mounting

fasteners.

Assembling the Handles

1 Assemble the mounting fasteners D at

both ends of the handle using a 1/4in. Allen

wrench.

Place the handle on the door by fitting

the handle

footprints over

the mounting

fasteners and

tightening the

set screws

with a 1/8in.

Allen wrench.

r _IL WARNING

When the customer takes apart the handle

or assemble it from a refrigerator, please bc

cautious of following things.

• Hold the handle with your own hand to

make sure not to drop the handle to the

floor or instep while taking apart the handle

from a refrigerator.

• Do not swing the handle towards people or

animals after taking apart the handle.

• Insert the bracket hole of the handle into

the stopper bolt of the door exactly, and

then assemble the set screws to fix the

handle.

• Check if there's any gap between the door

and handle after fixing the handle.

Removing/Assembling the

Doors and Drawers

Removing the doors is always recommended

when it is necessary to move the refrigerator

through a narrow opening.

f_ WARNING

. If your entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway,

• Use two or more people to remove and

install the refrigerator doors. Failure to do

so can result in back or other injury.

• Disconnect the electrical supply to the

refrigerator before installing. Failure to do

so could result in serious injury or death.

• Do not put hands, feet or other objects into

the air vents or bottom of the refrigerator.

You may be injured or receive an electrical

shock.

• Be careful when handling the hinge and

stopper. It may result in injury.

• Remove food and bins from the doors and

drawers before detaching.

Removing fhe Leff Refrigerafor Door

The water supply is connected to the

upper right part of the rear surface of the

refrigerator. Remove the ring in the joint

area. Hotd the water supply connection

and gently push the Collet to detach the

water supply line as shown in O and _.

'_-@ NOTE

Detachment of the water supply line is

applicable onty when detaching the left

refrigerator door,

14 INSTALLATION

(2) _1)

(3).

(7)/

2 Open the left door. Remove the top hinge

cover screw (1). Lift up the cover (2).

3 Remove the cover.

4 Pull out the tube (3).

5 Disconnect all wire harnesses (4).

6 Remove the grounding screw (5).

7 Rotate the hinge lever (6)

counterclockwise. Lift the top hinge (7)

free of the hinge lever latch (8).

8 Lift the door from the middle hinge pin and

remove the door.

9 Place the door, inside facing up, on a non-

scratching surface.

Removing fhe Righf Refrigerafor Door

(2)

1 Open the door. Remove the top hinge

cover screw (1). Lift up the cover (2).

2 Remove the cover.

3 Rotate the hinge lever (3) clockwise. Lift

the top hinge (4) free of the hinge lever

latch (5).

4 Lift the door from the middle hinge pin and

remove the door.

5 Place the door, inside facing up, on a non-

scratching surface.

A CAUTION

en lifting the hinge free of the latch, be I

.careful that the door does not fall forward.

CAUTION ------_]

en liftingthe hingefreeof the latch,be I

AssemblingfheRighf Refrigerafor

Door

Install the right-side door first.

1 Lower the door onto the middle hinge

pin. Make sure that the plastic sleeve is

inserted into the bottom of the door,

__ (2)

2 Fit the top hinge (4) over the hinge lever

latch (5) and into place.

3 Rotate the lever (3) counterclockwise to

secure the hinge.

4 Hook the tabs on the right side of the

hinge cover (2) under the edge of the top

hinge (4) and position the cover in place,

5 Insert and tighten the cover screw (1).

INSTALLAT ON 15

Assembling fhe Leff Refrigerafor

Door

Install the left refrigerator door after the right

door is installed.

1 Lower the door onto the middle hinge pin.

(6)z

(7)" (8) /

i :=_ (4)

2 Fit the top hinge (7) over the hinge lever

latch (8) and into place.

3 Rotate the lever (6) clockwise to secure

the hinge.

4 Install the grounding screws (5) and

connect the two wire harnesses (4).

5 Push the water tube (3) located at the top

of the left door into the hole beside the left

hinge on the top of the cabinet until it exits

through the back.

6 Insert the water supply tube (3) into the

connector until you see only one scale

mark. Fully insert the tub cover (15 mm).

7 Hook the tabs on the left side of the hinge

cover (1) under the edge of the top hinge (7)

and position the cover in place,

8 Insert and tighten the cover screw (1).

16 INSTALLATION

9 Insert the water supply tube at least 5/8 in.

(15 mm) into the connector.

10 Hook the tab on the door switch side

of the cover under the edge of the wire

opening in the cabinet top.

11 Position the cover into place. Insert and

tighten the cover screw.

--@ NOTE

1) Gently press the Coltet and insert the

tube until only one line shows on the

tube.

(Correct)

(Incorrect)

2) Pull the tube to make sure that the

tube is tightly fastened and then insert

the clip.

Removing the Freezer Drawers

The top, middle and bottom drawers are all

removed in the same way. tn the following

figures, the Pullout Drawer located above the

freezer drawer is not shown for clarity.

....Z_ CAUTION

• Use two or more people to remove and

install the freezer drawer. Failure to do so

can result in back or other injury.

Do not hold the handle when removing

or replacing the drawer. The handle may

come off and it could cause personal

injury.

• Be careful of sharp hinges on both sides

of the drawer.

• When you lay the drawer down, be

careful not to damage the floor.

Do not sit or stand on the freezer drawer.

• To prevent accidents, keep children and

pets away from the drawer. Do not leave

the drawer open.

1 Pull the drawer open to full extension.

Remove the lower basket by lifting basket

from rail system.

assembly.

Press in the tabs on the rail covers and

lift them up to separate from the rail

INSTALLATION 17

Remove the rail screw (_) on both the left

and right rails.

With both hands, grasp the sides of the door

and pull it up to separate it from the rails.

-_ CAUTION

When you remove the drawer, do not

hold the handle. The handle may come

off and it could cause personal injury.

With both hands, hold each rail and push it in

to allow both rails to slide in simultaneously.

Assembling fhe Freezer Drawer

1 With both hands, pull out each rail

simultaneously until both rails are fully

extended.

Hook the door support (_) into the rail tabs

(_) on both sides.

3 Lower door into final position and tighten the

screws (_).

18 INSTALLATION

Assembling the Freezer Drawer

(continued)

4 Make sure you have the correct rail cover

for each side.

F_ WARNING

, if the Durabase divider is removed, there is

enough open space for children or pets to

craw1inside. To prevent accidental child and

pet entrapment or suffocation risk, DO NOT

allow them to touch or go near the freezer

drawer.

• DO NOT step or sit down on freezer

drawer.

Align the tabs on the covers with the

assembly holes on each rail, and snap the

rail covers in place to secure.

Assembly

Ho,o

With the drawer pulled out to full

extension, insert the lower basket (_) in

the rait assembly.

INSTALLATION 19

Connecfincj the Wafer Line

Before You Begin

This wafer line installation is not covered by the

refrigerator warranty. Follow these instructions

carefully to minimize the risk of expensive water

damage

Water hammer (water banging in the pipes) in

house plumbing can cause damage to refrigerator

parts and can lead to water leakage or flooding.

Call a qualified plumber to correct water hammer

before installing the water supply line to the

refrigerator.

"-Z_ CAUTION

To prevent burns and product damange,

only connect the refrigerator water line to

a cold water supply.

If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the OFF (O) position,

.-_ CAUTION

Do not install the icemaker tubing _n

areas where temperatures fall below

freezing.

Wafer Pressure

A cold water supply. The water pressure must

be between 20 and 120 psi (140 and 830 kPa)

on models without a wafer filter and between 40

and 120 psi (280 and 830kPa) on models with

a water filter

If a reverse osmosis water filtration system is

connected to your cold wafer supply, this water

line installation is not covered by the refrigerator

warranty. Follow the following instructions

carefully to minimize the risk of expensive water

damage.

If a reverse osmosis water filtration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 and 60 psi ( 280 and 420

kPa), less than 2.0~30 sec to fill a cup of 7 oz

(200 cc) capacity

CAUTION

Wear eye protectionduringinstallation

topreventinjury.

If the wafer pressure from the reverse osmosis

system is less than 21 psi (145 kPa) (takes more

than 40 sec to fill a cup of 7 oz (200 cc) capacity):

, Check to see if the sediment filter in

the reverse osmosis system is blocked.

Replace the filter if necessary.

• Allow the storage tank on the reverse

usage

• If the issue concerning water pressure

from reverse osmosis remains, call a

licensed, qualified plumber.

All installations must be in accordance

with local plumbing code requirements

What You Will Need

Copper Tubing, 1/4in. outer diameter, to

connect the refrigerator to the water

supply Be sure both ends of the tubing

are cut square

To determine how _"

much tubing you need:

measure the distance

from the water valve on the back of the

refrigerator to the water supply pipe.

Then, add 8 feet

(24m) Be sure there is sufficient extra

tubing (about 8 feet [24 m] coiled into 3

turns of about 10 in [25cm] diameter)

to allow the refrigerator to move out

from the wall after installation

• Power drill.

o 1/2in. or adjustable

wrench.

Flat blade and Phillips

head screwdrivers,

e Two 1,4in. outer

diameter compression

nuts and 2 ferrules (sleeves) to connect the

copper tubing to the shutoff valve and

the refrigerator wafer valve

20 INSTALLATION

• If your existing copper water line has a

flared fitting at the end, you will need

an adapter (available at plumbing supply

stores) to connect the water line to the

refrigerator OR you can cut off the flared

fitting with a tube

cutter and then use a

compression fitting.

• Shutoffvalve to

connect to the coldwater line. The shutoff

valve should have a water inlet with a

minimum inside diameter of 5/32 in. at

the point of connection to the COLD

WATER LINE. Saddle4ype shutoff valves

are included in many water supply kits.

Before purchasing,

make sure a saddle-

type valve complies

with your local

plumbing codes.

. @ NOTE -.

]

A self piercing saddle type water valve /

should not be used.

Wafer Line Insfallafion Insfrucfions

_ WARNING

When using any electrical device

(such as a power drill) during

installation, be sure the device is

battery powered, double insulated

or grounded in a manner that will

prevent the hazard of electric shock.

Install the shutoff valve on the nearest

frequently used drinking water line.

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet to relieve the

pressure on the line.

2 CHOOSE THE VALVE LOCATION

Choose a location for

the valve that is easily

accessible. It is best to

connect into the side of a

vertical water pipe. When

it is necessary to connect

into a horizontal water

pipe, make the connection to the top or

side, rather than at the bottom, to avoid

drawing off any sediment from the water

pipe.

3 DRILL THE HOLE FOR THE VALVE

Drill a 14in. hole in

the water pipe using

a sharp bit. Remove

any burrs resulting

from drilling the hole

in the pipe. Be careful

not to allow water

to drain into the drill. Failure to drill a 1Ain.

hole may result in reduced ice production

or smaller cubes.

NOTE ..................................

The hookup line cannot be white, plastic /

tubing. Licensed plumbers must use I

only copper tubing NDA tubing #49595 I

or 49599 or Cross Link Polyethylene I

La page charge ...

LG LFXS24566S/00 Le manuel du propriétaire

Marque: LG

Modèle: LFXS24566S/00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG LFXS24566S/00 Owner's manual
español: LG LFXS24566S/00 El manual del propietario

LG LFXS24566S/00 Le manuel du propriétaire

LG LFXS24566S/00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents