GE TBX18SABKLAA Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
GEAppliances
©
Models
14, 16,18
_geapplia,oes.com Part No. 162D3905PO08 Pub.No. 49-60056 9-99JR
m
u
m
m
m
.h
m
m
m
m
m
Congratulations!
YouAre Now Part ofthe GEFamily
Welcome to the GE family. We're proud of our
quality products and we are colrmfitted to providing
dependable service. You'll see it in this easy-to-use
Owner's Manual and you'll hear it in the friendly
voices ofom" ca_stomer service deparnnent.
Best of all, you'll experience these values each time
you use your refrigerator. That's important, because
your new refrigerator will be part of your family for
many years. And we hope you will be part of ours for
a long time to come.
We thank you for buying GE. We appredate your
purchase, and hope youwill continue to rely on us
whenever you need quality appliances for your home.
GE& You,A ServicePartnership.
YOURRECORDS
Write the model andserial numbers here:
#
#
You can find them on a label on the upper left side of the fresh
food compartment.
Staple sales slip or cancelled check here.
Proof of the original purchase date is needed to obtain service
under the warranty.
READTHISMANUAL
Inside you will find many helpful hints on how to use and
maintain your refrigerator properly.Just a little preventive care
on your part can save you a great deal of time and money over
the life of your refrigerator.
IFYOUNEEDSERVICE
You'll find many answers to common problems in the Before You
CallForService section. If you review our chart of Troubleshooting
"tipsfirst, you may not need to call for service at all.
If you do need service, you can relax knowing help is only a
phone call away. A list of toll-free customer service numbers is
included in the back section. Or, in the U.$., you can always call
the GE Answer Center ®at 800.626.2000, 24 hours a day, 7 days
a week. ta Canada, call 1_00-361-3400.
IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
Keep fingers out of the "pinch point" areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
In refrigerators with automatic icernakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating
element that releases the cubes. Do not place
fingers or hands on the automatic icemaking
mechanism while the refrigerator is plugged in.
Unplug the refrigerator before cleaning and
making repairs.
NOTE:Westronglyrecommendthatanyservicingbe
performedbya quafifiedindividual
Turning the control to the OFFposition does
not remove power to the light circuit.
Do not refreeze frozen foods which have
thawed completely.
MESURESDES 'CURIT "IMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
A,AVERTISSEMENT!
N'utilisez cet #lectrom6nager quepour rusage auquel il estdestin#, comme expliqu# clansle prOsent manuel
MESURESDESECURITE
Lorsque vous utilisez un appareil #lectrique, observez toujours les mesures de sOcurit# de base,
y compris les suivantes.
Installez le r_frigarateur conform_ment aux
directives d'installation avant de l'utilise_.
Ne laissez pas les enfants grimper, s'asseoir,
se tenir debout ni se pendre aux clayettes du
r_frig_rateur. Ils pottrraient endommager le
r_frig_rateur et se blesser gravement.
N'entreposez et n'utilisez pas d'essence ou autres
vapeurs et liquides inflammables _ proxhnitfi de
cet appareil ou de tout autre appareil
_lectrom_nager.
£1oignez les doigts des parties du r_frig_rateur o_
l'on peut facilernent se pincer :les espaces entre
les portes et entre les portes et les placards sont
toujours _troits. Soyez prudent lorsque vous fermez
les portes de l'appareil en presence des enfants.
Sivotre r_frig_rateur est dotk d'une machine _t
glaqons automatique _vitez le contact avec les
pieces mobiles du m_canisme _jectettr, ou avec
l'_l_ment chauffant qui lib_re les gla_ons. Ne
posez pas les doigts ou les mains sur le m_canisme
de la machine &glagons pendant que le
r_frig_ratettr est branch,.
Ne touchez pas les surfaces froides du congelateur
si vous avez les mains humides ou mouillees : la
peau risque d'adherer &ces surfaces tres froides.
Debranchez votre refrigerateur avant de le
nettoyer ou de le reparer.
REMARQUE:Nousvousrecommandonsvivome_tdoconfier
touter#paralion_ untechnicie_qualifi#.
Lorsque vous reglez la commande sur OFF
(eteint), l'alhnentation electrique de l'ampoule
n'est pas coupee.
Ne recongelez pas les ailments surgel_s qui ont
compl_tement d_gel&
3
A DANGER!RISKOFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
Child entrapment and suffocation are not
problems of the past.Junked or abandoned
_ efrigerators are still dangerous...even if they
will sit for "just a few days." If you are getting
rid of your old refrigerator, please follow the
instructions below to help prevent accidents.
Before YouThrow Away YourOld
Refrigerator or Freezer:
Take off the doors.
Leave the shelves in place so that children
may not easily cfimb inside.
CFCDisposal
Your old refrigerator has a coofing system that
used CFCs (chlorofluorocarbons). CFCs are
befieved to harm stratospheric ozone.
If you are throwing away your old refrigerator,
make sure the CFC refrigerant is removed for
proper disposal by a qualified selwicer. If you
intentionally release this CFC refrigerant you
can be subject to fines and imprisonment under
provisions of environmental legislation.
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the
United States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having
a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum)
and 120 volts.
DANGER!RISQUESPOURLESENFANTS
COMMENTVOUSOEBARRASSER
CONVENABLEMENTDEVOTREANCIENRE-FRIGERATEUR
Les enfants pris au pi_ge ou morts d'asphyxie sont
toujours d'actuafit& _ r_frig_rateurs abandonn_s
sont toujours aussi dangereux, m_me si on n'attend
que ,,quelquesjours,_ pour s'en d_ban-asser. Sivous
ne gardez pas votre ancien r_ffig_rateur, veuillez
sffwre les directives d_lessous afin de pr_venir les
accidents.
Avant de vous ddbarrasser de votre ancien
rdfrigdrateur ou eongdlateur :
D_montez les portes.
Laissez les clayettes en place afin d'emp_cher les
enfants de grimper &l'int_rieur.
Se ddbanasserdu CFC
Votre ancien r_frig&-ateur a un syst_me de
refroidissement qui a utilis_ les CFC
(chlorofluorocarbones). Les CFC sontjug_s nocifs
pour l'ozone sWatosph_rique.
Si vous vous d_barrassez de votre ancien
r_frig_rateur, assurez-vous que le frigorig_ne avec
CFC soit enlev_ correctement par un technicien
qualifi& Sivous lib_rez intentionnellement ce
frig_orig_ne avec CFC vous pouvez etre somnis aux
contraventions et _tl'emprisonnement sons
provisions des lois sur l'environnement.
4
CORDONSPROLONGATEURS
Nous vous recommandons fortement de ne pas utiliser de cordons prolongateurs _ cause des risques
potentiels qu'ds pr#sentent clanscertaines conditions,
Toutefois si vous d_ddez d'ufiliser tout de m_me un cordon prolongateur, il est absolument n_cessaire
qu'il s'agisse d'un cordon _t3 ills avec nfise _tla terre pour appareils _lectrom_nagers homologu_ UL
(aux Etats-Unis) ou certifi_ CSA (au Canada), pom_m d'une fiche et d'une prise raises _.la terre
de 15 amperes (minimum) et de 120 volts.
IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
A WARNING!
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safe_ this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall oudet is
encountered, it is your personal responsibility
and obligation to have it replaced with a properly
grounded 3-prong wall outlet.
The refrigerator should always be plugged into
its own individual electrical outlet which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise danaaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
MESURESDES 'CURIT "IMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
A AVERTISSEMENT!
RACCOROEMENTELECTRIQUE
Ne coupez ni retirez en aucun cas la treisi#me broche (mise _ la terre) de la fiche du cordon
d'alimentation. Pour votre s#curit#, cet appareil doit #tre correctement mis _ la terre.
Le cordon d'alimentation de cet appareil est muni
d'une fiche _t3broches (mise a la ten'e) qui se
branche darts une prise murale ordinaire ft3
alv_oles (mise ftla terre) pour r_duire au minimum
les risques de chocs 41ectriques.
Faites exanfiner la prise de courant et le circuit par
un _lectriden qualifi_ pour vous assurer que la prise
est correctement raise &la ten'e.
Sila prise murale est du type standard ft2 alv_oles, il
vous incombe de la faire remplacer par une prise ft3
alv_oles correctement mise &la terre.
Le r_frig_rateur doit toujours _tre branch_ dans sa
propre prise de courant, dont la tension nominale est
identique ftcelle indiqu_e sur la plaque signal_tique.
Cette precaution est recoInmand_e pour garantir
un rendement optimum et _viter une surcharge des
circuits _lectriques de la r_sidence, ce qui poun'ait
crier un risque d'incendie par surchauffe des ills.
Ne d_branchezjan_tis le r_frig_rateur en tirant sur le
cordon d'alimentation. Saisissez fermement la fiche
du cordon et tirez droit pour la retirer de la prise.
R_parez ou remplacez imm_diatement tout cordon
effiloch_ ou endommag& N'utilisez pas un cordon
fendill_ ou pr_sentant des signes d'usure.
Lorsque vous d_placez votre r_frig_rateur du tour,
faites attention de ne pas lefaire rouler starle cordon
d'alimentation afin de ne pas l'endommager.
5
IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
USEOFADAPTERPLUGS(Adapterplugs not permitted in Canada)
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.
However, if you must use an adapter, where local
codes permit, a temporaryconnectionmay be made
to a properly grounded 2-prong wall outlet by use
of a UL-fisted adapter available at most local
hardware stores.
The larger slot in the adapter must be aligned with
the larger slot in the wall outlet to provide proper
polarity in the connecton of the power cord.
When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand while pulling the power cord plug with
the other hand. If this is not done, the adapter
ground terminal isvery hkely to break with
repeated use.
If the adapter ground terminal breaks, DONOT
USEthe refrigerator until a proper ground has
been established.
Attachingtheadaptergroundterminaltoa walloutlet
coverscrewdoesnotgroundtheapplianceunlessthe
coverscrewismetal,andnot insulated,and thewall
outlet isgroundedthroughthehousewiring. Youshould
havethecircuitcheckedbya qualifiedelectricianto
makesumtheoutlet isproperlygrounded.
Readandfoflow thisSafetyInformationcarefufly.
SAVETHESEINSTRUCTIONS
MESURESDESECURITEIMPORTANTES.
LISEZD'ABORDTOUTESLESDIRECTIVES.
6
FICHEO'ADAPTATION€icesd'_daptationnonpermisesa. Canada)
Nous vous recommandons fortement de ne pas utiliser une fiche d'adaptation _ cause des fisques
potentiels qu'elle pr#sente clanscertaines circonstances.
Toutefois, si vous d6ddez d'ufifiser tout de m6me
tree fiche d'adaptation, vous pouvez effectuer un
raccordementtempotaire,si les codes locaux le
permettent, dans une prise de courant _ 2 alv6oles
ad6quatement mise _ la re(re en ufilisant une fiche
d'adaptaton homologu_e UL, en vente dans la
plupart des quincailleries.
La fente la plus longale de la fiche doit _tre align6e
avec lafente la plus longue de la prise mmaie afin
d'assurer la polarit_ appropri_e pour le
branchemem du cordon d'alimentation.
Sila borne de raise _tla terre de la fiche casse,
NTJTILISEZPASI'appareiltant qu'une raise alla terre
adequate n'aura pas _t_ r_tablie.
Lefait de fixerla bornede mise_ la termdela fiche
d'adaptation_ laplaquedela prisedecourantn'assure
pasautomatiquementlamise_ la terredeI'appareil.II
faut quela vissoit enm#tal,nonisol#e,etquelaprisede
courantsoitmise_ la termpar fentremiseduc#blagede
la r#sidence.Faitesv#rifierle circuitpar un#lectricien
qualifi#pour vousassurerquelaprise estad#quatement
mise_ laterre.
Lorsque vous d_branchez le cordon d'alimentation
de la fiche d'adaptation, saisissez toujours lafiche
d'une main pendant que vous tirez sur la fiche du
cordon d'alimentation de l'au/we. Sinon,
la borne de nfise ftla re(re de la fiche d'adaptation
risque de casser avec le temps.
Veuillezfireetsuivreattenfivementcosmesuresdes#curit#.
CONSERVEZCESDIRECTIVES
Aboutthetemperaturecontroldial
Turning the dial to OFFstops cooling in both compartments--fresh food and freezer.
,5
ControlSettings
Temperature ControlDial
The temperature control dial has nine settings plus OFF.I is the warmest. 9is the coldest.
At first, set the dial at 5.
After using the refrigerator, adjust the dial if necessary.
Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting
that's best suited to your needs.
Allow 24 hours for the refrigerator to get cold.
7
Aboutthefreshfoodcompartmentshelves.
Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.
Half-Width Shelves
One end of the shellrests on a molded
side-wall support; a bracket on the other
end hooks into a track on the rear
cabinet wail.
Toremove, lift the shell up at front, then
off the support and out of the track.
Toreplace, select desired shellheight.
With shellfront raised sfightly, hook the
bracket's top lug into the track, then
lower the shellonto the support.
NOTE:Theshelfto theright of thetrackis
designedtohookinto theright-handslot,
theshefftotheleft is designedtohook
into theleft-handslot.
Full-14rtdthShelves
Some models have a steel wire sliding
shell, a stationary tempered glass shell or
two steel wire stationary shelves. These
shelves can be moved to another place in
the fresh food compartment.
The full-width sliding shelf has stop-locks.
When placed correctly on the shell
supports, the shellwill stop before coming
completely out of the refrigerator and will
not tilt when you place food on it or
remove food from it.
Toremovethefull-width shelves,lift the
rear of the shell and pull forward.
Toremovea full-width sheffwhen thefresh
foodcompartmentdoorcannothe opened
fully,lift the rear of the shell, pull forward
and down, tilt the shelland take it out.
8
Aboutthefreezercompartmentshelves.
Some models have an ice-tray shelf and some have a full-width step shelf.
Ice- TraySheff
Toremoveb_eice-tray shelf,lift the left
side of the shelf offits supports, then pull
the shelf to the left to free it of the plug
supports. Pull the shelf to the fight to
free the pins from the holes in the
cabinet wall.
StepSheff
Toremovethe stepshelf:
[] Lift left side of shelf slightly.
[]Move shelf to the left to free its fight
ends from holes in the cabinet wall.
[]Lower fight side of shelf, move shelf to
the fight and take it out.
Toreplace thestepshelf:.
]With shelf tilted as shown, fit left ends of
shelf into holes in cabinet wall.
[]Lift left side of shelf slightly, swing shelf
up, fit fight ends of shelf into holes in
cabinet wall, and lower shelf into place.
Aboutthestoragedrawers.
Not all features are on all models.
Fruit and Vegetable Drawers
Excess water that may accumulate in the
bottom of the drawers should be emptied
and the drawers wiped dry.
Snacks Drawer
The snacks drawer can be moved to the
most useful location for your family's
needs.
9
Aboutstoragedrawer andcoverremoval
Not all features are on all models.
Drawer and Cover Removal
Drawers can be removed easily by grasping
the sides and lifting up slightly while
pulling drawers past the atop location.
Full-Width Drawer with Plastic Cover
Toremovethecover,lift it offits supports,
pull it forward, tilt it and take it out.
Twin Drawers with Glass Cover
Toremove:
[]Remove the drawers.
[]Reach in, push the front of glass cover
up, and at the same time, pull it
forward as far as it will come.
Tilt it and take it out. Avoid cleaning the
cold glass cover with hot water because
the extreme temperature difference may
cause it to break.
[]Remove the drawer frame. (Always
remove the glass cover before you
take out the drawer frame.)
Lift the frame off the supports at each
side and back, pull it forward, tilt it and
take it out.
Toreplace:
[]Lower the frame until it rests on the
supports at each side and back.
[]Replace the glass cover, pushing its
rear edge firmly into the rear frame
channel and gently lowering the front
into place.
[]Replace the drawers.
10
Aboutthe automaticicemaker.
A newly-installed refrigerator may take 8 to 12hours to begin making ice.
Automatic Icemaker (onsomemodels)
The icemaker will produce eight cubes
per cycle--approximately 100 cubes in a
24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.
If the refrigerator is operated before
the water connection is made to the
icemaker, keep the feeler arm in the
STOP(up) position.
When the refrigerator has been
connected to the water supply, move the
feeler arm to the ON (down) position.
The icemaker will fill with water when it
cools to freezing. A newly-installed
refrigerator may take 8 to 12 hours to
begin making ice cubes.
Throw away the first few batches of ice to
allow the water line to clear.
Be sure nothing interferes with the swing
of the feeler arm.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy and taste stale.
Icemaker Accessory Kit
If your refrigerator did not already come
equipped with an automatic icemaker,
an icemaker accessory kit is available at
extra cost.
Check the back of the refrigerator for the
specific icemaker kit needed for your
model.
11
Careand cleaningofthe refrigerator.
Clean the condenser coils at least
once a yea£
Cleaning the Outside
Thedoorhandlesandtrim (on some
models). Clean with a cloth dampened
with soapy water. Dry with a soft cloth.
Keep theoutsideclean.Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish
detergent. Dry and polish with a clean,
soft cloth.
Donot wipetherefrigerator witha soileddish
clothor wet towel Thesemayleavea residue
that canerodethepaint. Oonot usescouring
pads,powderedcleaners,bleachorcleaners
containingbleachbecausetheseproductscan
scratchandweakenthepaint finish.
Cleaningthe Inside
Tohelppreventodors,leave an open box
of baking soda in the fresh food and
freezer compartments.
Unplugtherefrigeratorbeforecleaning.
If this is not practical, _-ing excess
moisture out of sponge or cloth when
cleaning around switches, lights or
controls.
Use an appliance wax polish on the
inside surface between the doors.
Use warm water and baking soda solution-
about a tablespoon (15 ml) of baking soda
to a quart (1 1)of water. This both cleans
and neutralizes odors. Rinse and wipe dry.
After cleaning the door gaskets, apply a
thin layer of petroleum jelly to the door
gaskets at the hinge side. This helps keep
the gaskets from sticking and bending
out of shape.
Avoidcleaningcoldglassshelves(onsome
models)withhot waterbecausetheextreme
temperaturedifferencemaycausethemto
break.Handleglassshelvescarefully.Bumping
temperedglasscancauseit toshatte[
E-viterdenettoyerlostablettesen verrefroides
(surcertainsmod#les)_I'eauchaudepareeque
I'#cartde temp#retereextremerisquedelos
craquecManipulerlesteblettesonverreavec
precaution.Leverretremp#soumis_ un choc
risquedesofracasse[
Donot washanyplasticrefrigeretorpartsin
thedishwasher.
Under the Refrigerator
For most efficient operation, keep the
area under the refrigerator clean. Turn
the temperature control dial to OFF.
Sweep away or vacuum up dust.
For best results, use a brush specially
desigaaed for this purpose. It is available
at most appliance parts stores.
12
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
Turn the leveling legs at each front
corner of the refrigerator counter-
clockwise until the rollers support the
refrigerator. Pull the refrigerator straight
out and return it to position by pushing it
straight in. Moving the refrigerator in a
side direction may result in damage to
the floor covering or refrigerator.
Whenpushingtherefrigeratorback,makesure
youdon't roll overthepowercordor icemaker
supplyline (onsomemodels).
Enpoussantle rOfrig_rateurenplace,veiller_ no
pasle faireroulersurle cordond'alimentationou
la canalisationd'eaudela machine_ glagons
(surcertainsmodkles).
After rolling the refrigerator back into
place, turn the legs clockwise until the
legs again bear the weight of the
refrigerator.
Light Bulb Replacement
To replace a burned-out bulb, unplug
the refrigerator from its electrical outlet,
unscrew the bulb when cool and replace
it with an appliance bulb of the same or
lower wattage.
Tumingthecontrolto theOFFpositiondoesnot
removepower tothelight circuit.
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refrigerator. Move
the temperature control dial to the OFF
position, and clean the interior with a
baking soda solution of one tablespoon
(]5 ml) of baking soda to one quart (] 1)
of water. Leave the doors open.
Move the icemaker feeler arm to the
STOP(up) position and shut off the water
supply to the refrigerator.
If the temperature can drop below
freezing, have a qualified servicer drain
the water supply system (on some
models) to prevent serious property
damage due to flooding.
Preparing to Move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Besuretherefrigeratorstaysin anupright
positionduringmoving.
13
Preparingtoinstall therefrigerator.
Read these instructions completely and carefully.
WaterSupplyto theIcemaker o..omomo,o,.j
If the refrigerator has an icemaker, it will have to
be connected to a cold water line.
A water supply kit (containing copper tubing,
shutoffvalve, fittings and instructions) is
available at extra cost from your dealer or
from Parts and Accessories, 800526-2002.
RefrigeratorLocation
Do not install the refrigerator where the
temperature will go below 60 °F (16°C)
because it will not run often enough to
maintain proper temperatures.
Install it on a floor strong enough to support it
fully loaded.
Clearances
Allow the following clearances for ease
of installation, proper air circulation and
plumbing and electrical connections:
Sides .......................... 3/4" (19 mm)
Top ............................ 1" (25 mm)
Back .......................... 1" (25 mm)
Rollers and Leveling Legs
Levelinglegsnear each front corner of the
refrigerator are adjustable. They firefly position
the refrigerator and prevent it from moving
when the doors are opened. Leveling legs should
be set so the front of the refrigerator is raised just
enough that the doors close easily when opened
about halfway.
Turn the leveling legs clockwise toraise the
refrigerator, counterclockwisetolower it.
Rollersnext to the leveling legs allow you to move
the refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight
of the refrigerator is transferred from them to
the rollers. After rolling the refrigerator back
into place, turn the legs clockwise until the legs
again bear the weight of the refrigerator.
14
Installingthe water line.
Read these instructions completely and carefully.
J
BeforeYouBegin
This water line installation is not warranted by
the refrigerator or icemaker manufacturer.
Follow these instructions carefully to minimize
the risk of expensive water damage.
Water hammer (water banging in the pipes)
in house plumbing can cause damage to
refrigerator parts and lead to water leakage
or flooding. Calla qualified plumber to correct
water hammer before installing the water supply
line to the refrigerator.
Toprevent burns and product damage, do not
hook up the water line to the hot water line.
ff you use your refrigerator before connecting
the water line, make sure the icemaker feeler
arm is kept in the STOP (up) position.
Do not install the icemaker tubing in areas
where temperatures fall below freezing.
When using any electrical device (such as a
power drill) during installation, be sure the
device is insulated or wired in a manner to
prevent the hazard of electric shock.
All installations must be in accordance with
local plumbing code requirements.
WhatYouWill Need
Todetermine how much copper tubing you need:
Measure the distance from the water valve on the
back of the refrigerator to the water supply pipe.
Then add 8 feet (244 cm). Be sure there is
sufficient extra tubing [about 8 feet (244 cm)
coiled into 3 turns of about 10 inches (25 cm)
diameter] to allow the refrigerator to move out
from the wall after installation.
A water supply kit (containing copper tubing,
shutoffvalve and fittings listed below) is
available at extra cost fi'om your dealer or
from Parts and Accessories, 800-626-2002.
A sold watersupply.The water pressure must
be between 20 and 120 p.s.i. (1.4-8.1 bar).
mPowerdrill.
Coppertubing,1/4" outer diameter to connect
the refrigerator to the water supply. Be sure
both ends of the tubing are cut square.
Donotuseplastictubingorplasticfittings becausethe
water supplyline is underpressureatall times.Certain
typesofplastictubingmaybecomebrittle withageand
crack,resultingin waterleakage.
Two I/4" outerdiametercompressionnutsand
2 ferrules(sleeves)_to connect the copper
tubing to the shutoffvalve and the refrigerator
water valve.
If your existing water line has a flared fitting at
the end, you will need an adapter (available at
plumbing supply stores) to connect the water
line to the refrigerator ORyou can cut off the
flared fitting with a tube cutter and then use a
compression fitting.
Shutoffvalve to connect to the cold water line.
The shutoffvalve should have a water inlet
with a minimum inside diameter of 5/32" at
the point of connection to the COLDWATER
LINE. Saddle-type shutoffvalves are included
in many water supply kits. Before purchasing,
make sure a saddle-type valve complies with
your local plumbing codes.
15
Installing the water line.
Read these instructions completely and carefully.
ShutOff theMain WaterSupply
Turn on the nearest faucet long enough to clear the
Install the Shutoff Valve
[]Install the shutoffvalve on the nearest
frequently used drinking water line.
[]Choose a location for the valve that is easily
accessible. It is best to connect into the side
of a vertical water pipe. When it is necessary
to connect into a horizontal water pipe, make
the connection to the top or side, rather than
at the bottom, to avoid drawing off any
sediment from the water pipe.
[]Drill a 1/4" hole in the water pipe, using a
sharp bit. Remove any burrs resulting from
drilling the hole in the pipe.
line of water.
[]Fasten the shutoffvalve to the cold water pipe
with the pipe clamp.
[]Tighten the clamp screws until the sealing
washer begins to swell.
Do not overtighten or you may crush the copper
tubing,
PipeClamp
Saddle-Type
ShutoffValve
Washer
/Inlet End
ical ColdWaterPipe
Route the Copper Tubingand Connect It to the Shutoff Valve
Route the copper tubing between the cold water
line and the refrigerator.
Route the tubing through a hole drilled in the
wall or floor (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible.
Place the compression nut and ferrule (sleeve)
onto the end of the tubing and connect it to the
shutoffvalve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
Be sure there is sufficient extra tubing [about
8 feet (244 cm) coiled into 3 turns of about 10"
(25 cm) diameter] to allow the refrigerator to
move out from the wall after installation.
Saddle-TypeShutoffValve
OutletValve
_ CompressionNut
.=rrule(sleeve)
Turn On the Water and Rush Out the Tubing
[Turn the main water supply on and flush out _ Shut the water off at the water valve after
the tubing until the water is clear. _'_ about one quart (1 1) of water has been
flushed through the tubing.
16
Connect the Tubingto the Refrigerator
Before making the connection to the
refrigerator, be sure the refrigerator power cord
is not p/agged into the wa// out/et.
We recommend installing a water filter ifyour
water supply has sand or particles that could clog
the screen of the refrigerator's water valve.
Install it in the water line near the refrigerator.
[]Remove the plastic flexible cap from the
water valve.
[]Place the compression nut and ferrule
(sleeve) onto the end of the tubing as shown.
[]Insert the end of the copper tubing into the
water valve connection as far as possible.
While holding the tubing, tighten the fitting.
[]Fasten the copper tubing into the clamp
provided to hold it in a vertical position.
You may need to pry open the clamp.
1/4_CopperTubing
TubingClamp
1/4" CompressionNut
RefrigeratorConnection
Turn the Water On at the Shutoff Valve
Tighten any connections that leak.
Plug In the Refrigerator
Arrange the coil of copper tubing so that it does
not vibrate against the back of the refrigerator or
against the wall.
Push the refrigerator back to the wall.
Start the Icemaker
Set the icemaker feeler arm to the ON(down)
position. The icemaker will not begin to operate
until it reaches its operating temperature of 15 °F
(-9°C) or below. It will then begin operation
automatically if the icemaker feeler arm is in
the ON (down) position.
NOTE: The icemaker may doub/e-cyc/e when it
first starts, causing some water spi//age from
the icemaker into the ice bucket. This is norma/
and should not happen again.
17
Reversingthedoorswing.
Read these instructions completely and carefully.
ImportantNotes
When reversing the door swing:
Read the instructions all the way through
before starting.
Handle parts carefully to avoid scratching
paint.
Set screws down by their related parts to avoid
using them in the wrong places.
Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the
cabinet until door-swing reversal is completed.
These instructions are for changing the hinges
from the right side to the left side_f you ever
want to change the hinges back to the right side,
follow these same instructions and reverse all
references to left and right.
ToolsRequired
Phillips screwdriver
Masking tape
T20 or T25 Torxdriver, whichever your
model requires
5/16" hex-head socket driver
5/16" open-end wrench
Putty knife or thin-blade screwdriver
18
Removingthedoors.
Read these instructions completely and carefully.
Removing the Doors
[]Unplug the refrigerator from its electrical
outlet.
[]Empty all door shelves, including the dairy
compartment.
CAUTION: Do not let either door drop to the
floor. To do so could damage the door stop.
Remove the Freezer Door
[] Tape the door shut with masking tape.
[]With a 5/16" hex-head socket driver, remove
the screws that hold the top hinge to the
cabinet.
[]Lift the hinge (and the shim glued to it)
straight up to free the hinge pin from the
socket in the top of the door and set it aside,
along with its screws.
[]Remove the tape and tilt the door away from
the cabinet. Lift it off the bottom socket.
[]Set the door on a non-scratching surface with
the outside up.
[]Using a Torxdriver, transfer the 2 screws
from the opposite side of the cabinet to the
screw holes vacated by the top hinge removal.
Remove the Fresh Food Door
[] Tape the door shut with masking tape.
[]Using a 5/16" hex-head socket screwdriver
and a 5/16" open-end wrench, remove the
two screws holding the center hinge (and the
shim glued to it) to the cabinet. Lift the
center hinge to free its pin from the socket in
the top of the door, and set hinge and screws
aside.
[]Remove the tape and tilt the door away from the
cabinet. Lift the door from the pin in the bottom
hinge bracket. (If the plastic washer sticks to the
door bottom, put it back on the hinge.)
[]Set the door outside-up on a non-scratching
surface.
[]Using a Torxdriver, lransfer the two screws from
the opposite side of the cabinet to the screw
holes vacated by the center hinge removal.
[]Take one of the screws removed in step 2 and
start it in the outermost screw hole on the
opposite side. Do not drive it all the way down-
leave enough space under the screw head for
thickness of shim and bracket.
_,/Hinge Pin
CenterHingeBracketf _l_i_'PlasticWasher
19
Reversingthehardware.
Read these instructions completely and carefully.
Transfer Bottom Hinge to the Left
[]Remove the base grille (if your refrigerator
has one) by pulling it straight out.
[]Using a Torxdriver, move the bottom hinge
bracket (and shim glued to it) and plastic
washer from the right side to the left side.
HingeBracket
PlasticWasher
Transfer Top Hinge to the Left
Interchange hinge (and the shim glued to it)
and screws at top right with screws at top left of
cabinet.
Do not tighten screws on hinge side at this time.
Some hinges have four holes. Which holes you
use for installing the hinge depends on which
side you install the hinge.
The outer edge of the hinge should be parallel to
the edge of the case for correct installation.
Reversingthedoorhandles.
thstafling thehingeon theleft.
Instaflingthe hingeon theright
Read these instructions completely and carefully.
Transfer Fresh FoodDoor Handle
[]Remove the handle plug using a tape-tipped
putty knife under the edge, and remove the
screw underneath.
[]Remove the two screws holding the handle to
the top of the door.
[]Remove the handle.
[]Remove the screws from the right edge of the
door top and insert them into the handle
screw holes on the opposite side.
[]With tape-tipped putty knife or thin-blade
screwdriver, pry out the plug button from the
hinge hole on the left side of the door and
insert it into the hole on the opposite side
that was vacated by removal of the top hinge.
[]Pull the plug button from the front of the
door and transfer it to the opposite side.
®
®
PlugButton
Toreattachthe handleon
20 theoppositeside.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

GE TBX18SABKLAA Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

dans d''autres langues