Velodyne Acoustics Speaker System SPL-1000 Manuel utilisateur

Catégorie
Subwoofers
Taper
Manuel utilisateur

Ce manuel convient également à

Home Theater Subwoofer
SPL-800, SPL-1000,
and SPL-1200
Series II
Owner's Manual
Velodyne Acoustics, Inc.
345 Digital Drive
Morgan Hill, CA 95037
408.465.2800 voice
408.779.9227 fax
408.779.9208 Service fax
Web Site: www.velodyne.com
Service E-mail: [email protected]
Product E-mail: [email protected]
Technical E-mail: [email protected]
"
Not only was the little Velodyne the best
small
sub I've ever used,
it was one of the very best subs I've used.
"
-John Potis
SoundStage!, April 2002
"The SPL-1200 was able to hit an impressively deep 16 Hz."
-
Tom Noussaine
Sound & Vision, June 2001
"How do they get this kind of bass out of such a tiny box? Deep, tight,
tuneful and loud enough to rattle pictures on the wall--this is serious
subwoofing."
-Robert Deutsch
Stereophile Guide to Home Theater, September 1998
Printed on recycled paper
63-SPLII RevA 04/03
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel.
The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated.
2. Retain Instructions -- The safety and operating instructions should be retained for future reference.
3. Heed Warnings -- All warnings on the subwoofer and in the operating instructions should be adhered to.
4. Follow Instructions -- All operating and use instructions should be followed.
5. Water and Moisture -- The subwoofer should
not
be used near water -- for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, near a swimming pool, or the like.
6. Carts and Stands -- The subwoofer should be used only with a cart or stand recommended by the manufacturer
to avoid injury from tipover.
7. Wall or Ceiling Mounting -- The subwoofer should be mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Ventilation -- The subwoofer should be situated so that its location or position does not interfere with its proper
ventilation. For example, the subwoofer should not be situated on a bed, sofa, rug, or similar surface that
may block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9. Heat -- The subwoofer should be situated away from heat sources such as radiators, heat registers, stoves,
or other subwoofers that produce heat.
10. Power Sources -- The subwoofer should be connected to a power supply only of the type described in the
operating instructions or as marked on the subwoofer.
11. Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point at which they exit from the subwoofer.
12. Caution: To prevent electrical shock, match wide blade of plug to wide slot, fully inserted.
13. Cleaning -- The subwoofer should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods -- The power cord of the subwoofer should be unplugged from the outlet when left unused for
a long period of time.
15. Object and Liquid Entry -- Care should be taken so that objects do not fall and liquids are not spilled onto the
enclosure.
16. Damage Requiring Service -- The subwoofer should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen or liquid has been spilled into the subwoofer.
c. The subwoofer has been exposed to rain.
d. The subwoofer does not appear to operate normally or exhibits a marked change in performance.
e. The subwoofer has been dropped or damaged.
17. Servicing -- The user should not attempt to service the subwoofer beyond what is described in the operating
instructions.
18. Overloading -- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19. Replacement parts -- When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
20. Safety Check -- Upon completion of any service or service of repairs to this product, ask the service technician
to perform safety checks to determine that the product is in proper operating condition.
All other servicing should be referred to qualified service personnel.
18
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1
NOTES
Vorsicht: Zur Vermeidung von Gefahr durch elektrischen Schlag, Deckel (oder Rückwand) nicht
abnehmen. Produkt enthält keine Anwenderteile. Reparatur und Wartung nur von qualifiziertem
Fachpersonal vornehmen lassen.
Das Blitzsymbol dient als Hinweis auf unisolierte „gefährliche Spannungen“ innerhalb des Gehäuses,
deren Werte eine Berührungsgefahr für den Menschen darstellen können.
Das Symbol mit dem Ausrufungszeichen dient als Hinweis auf wichtige, in den Unterlagen des Subwoofers
enthaltene Bedienungs- und Wartungsvorschriften.
1. Anleitungen lesen - Alle Sicherheits- und Bedienungsanleitungen vor Inbetriebnahme des Subwoofers aufmerksam
durchlesen.
2. Anleitungen aufbewahren - Die Sicherheits- und Bedienungsanleitungen zur späteren Bezugnahme aufbewahren.
3. Warnungen beachten - Alle Warnungen am Subwoofer und in der Bedienungsanleitung unbedingt beachten.
4. Anleitungen befolgen - Alle Bedienungs- und Gebrauchsanleitungen genau befolgen.
5. Wasser und Feuchtigkeit - Subwoofer nicht in der Nähe von Wasser aufstellen, d.h. neben einer Badewanne,
Spüle, Waschmaschine, in einem feuchten Keller, in der Nähe des Swimmingpools o.ä..
6. Rollwagen und Ständer - Subwoofer nur mit einem vom Hersteller empfohlenen Rollwagen oder Ständer benutzen.
7. Wand- oder Deckenbefestigung - Subwoofer nur den Herstellerempfehlungen gemäß an der Wand oder Decke
befestigen.
8. Belüftung - Subwoofer so aufstellen, daß die erforderliche Belüftung nicht behindert wird. D.h., Subwoofer nicht auf
einer weichen Oberfläche wie einem Bett, Sofa, Teppich o.ä. aufstellen, die die Belüftungsöffnungen blockieren
kann. Subwoofer gleichfalls nicht in einem Regal oder Schrank unterbringen, worin die Luftzufuhr behindert wird.
9. Wärme - Subwoofer nicht in der Nähe von Wärmequellen, wie Heizkörpern, Wärmespeichern, Öfen oder anderen
wärmeerzeugenden Subwoofern aufstellen.
10. Netzanschluß - Subwoofer nur an eine der in der Bedienungsanleitung beschriebenen oder auf dem Subwoofer
angegebenen Stromquellen anschließen.
11. Netzkabelschutz - Netzkabel so verlegen, daß nicht daraufgetreten wird oder sie durch darauf-oder
dagegengestellte Gegenstände eingeklemmt werden können. Die Anschlußstellen des Netzkabels an Steckdosen
und am Subwoofer dabei besonders beachten.
12. „Vorsicht“: Zur Vermeidung von Gefahr durch elektrischen Schlag sicherstellen, daß der Schutzkontakt
des Steckers vollständig in die Steckdose eingeführt ist.
13. Reinigung - Subwoofer nur den Herstellerempfehlungen gemäß reinigen.
14. Betriebsfreie Zeiträume - Netzkabel des Subwoofers aus der Steckdose ziehen, wenn er über einen längeren
Zeitraum nicht benutzt wird.
15. Beschädigungen durch Gegenstände oder Flüssigkeiten - Es ist darauf zu achten, daß keine Gegenstände auf
das Gehäuse fallen oder Flüssigkeiten darauf verschüttet werden.
16. Beschädigungen, die eine Reparatur erforderlich machen - Subwoofer sollte von qualifiziertem Fachpersonal
repariert werden, wenn:
a. Das Netzkabel oder der Stecker beschädigt sind.
b. Gegenstände oder Flüssigkeiten in den Subwoofer gelangt sind.
c. Der Subwoofer dem Regen ausgesetzt wurde.
d. Der Betrieb des Subwoofers gestört ist oder seine Leistung deutlich nachgelassen hat.
e. Der Subwoofer fallengelassen oder beschädigt wurde.
17. Reparatur und Wartung - Durch den Benutzer auszuführende Wartungsmaßnahmen des Subwoofers sind auf die
in der Bedienungsanleitung angegebenen Prozeduren beschränkt.
18. Überlastung - Zur Vermeidung von Brandgefahr und elektrischem Schlag Wandsteckdosen,
Verlängerungskabel bzw. eingebaute Steckdosen nicht überlasten.
19. Ersatzteile - Wenn Ersatzteile benötigt werden, sicherstellen, daß der Servicetechniker entweder die vom
Hersteller angegebenen Ersatzteile benutzt oder Teile, die den Originalteilen entsprechende Kennwerte
besitzen. Die Verwendung von Ersatzteilen, die nicht zugelassen sind, kann Brände, elektrischen Schlag
oder andere Gefahren verursachen.
20. Sicherheitsprüfung - Nach Beendigung von Wartungs- oder Reparaturmaßnahmen an diesem Produkt vom
Servicetechniker Sicherheitsprüfungen zum Nachweis des ordnungsgemäßen Betriebszustandes vornehmen
lassen.
Alle anderweitigen Servicemaßnahmen von qualifiziertem Wartungspersonal durchführen lassen.
17
2
WICHTIGE SICHERHEITSHINWEISE
VORSICHT
GEFÄHRLICHE SPANNUNG
NICHT ÖFFNEN
Thank You for Purchasing an
SPL Series II Velodyne Subwoofer!
* NOTE: Please complete and return your warranty card within ten (10) days
or
Register
....
ON-LINE
.....
It's faster.....and easier
www.velodyne.com
FOR YOUR RECORDS. . .
DATE PURCHASED
____________________________________
DEALER
__________________________________________________
SERIAL #
_____________________________________________
Other Velodyne Subwoofer Products:
Digital Drive 1812
Digital Drive Series
DD-10
DD-12
DD-15 THX Ultra 2
DD-18 THX Ultra 2
Deco System
Deco System
Deco Satellites
CHT Series
CHT-8
CHT-10
CHT-12
CHT-15
CHT Front Row System
VX-10
DLS Series
DLS-3500
DLS-3750
DLS-4000
TM
TM
TM
continued. . .
Attention: Afin d’éviter tout risque d’électrocution, ne pas enlever le boitier (ou partie arrière de
l’enceinte). Aucune pièce ne doit être manipulée par l’utilisateur. Pour tout entretien, vous référer à un
personnel de service qualifié.
Le symbol de l’éclair avec la flèche sert à avertir l’utilisateur de la présence d’un “voltage dangereux”
non isolé dans l’enceinte du produit d’une magnitude pouvant constituer un risque
d’électrocution de personnes.
Le symbol du point d’exclamation sert à avertir l’utilisateur que d’importants conseils de fonctionnement
et de maintenance (entretien) sont fournis avec l’enceinte d’extrêmes graves.
1. Lire le mode d’emploi - Tous les conseils de sécurité et de fonctionnement doivent être lus avant de mettre en
marche l’enceinte.
2. Garder le mode d’emploi - Il est conseillé de conserver les conseils de sécurité et de fonctionnement pour un
éventuel usage futur.
3. Avertissements - Il est important de se conformer à tous les conseils de fonctionnement concernant l’enceinte
et à toutes les instructions inscrites sur l’enceinte.
4. Suivre les conseils - Tous les conseils d’utilisation et de fonctionnement doivent être suivis à la règle.
5. Eau et humidité - Ne pas utiliser l’enceinte près d’une source d’eau - par exemple, près de la baignoire, d’une
bassine de lavage, d’un évier de cuisine, d’un bac à lavage, dans un sous-seul mouillé, près d’une piscine…
6. Pieds et Supports - N’utiliser que des pieds et supports recommandés par le fabricant.
7. Assemblage mural ou au plafond - Se conformer uniquement aux instructions du fabricant pour fixer l’enceinte
sur un mur ou sur un plafond.
8. Ventilation - Il est important de placer l’enceinte de telle sorte qu’elle ne gêne pas sa propre ventilation. Par
exemple, ne pas placer l’enceinte sur un lit, un canapé, sur la moquette, ou sur toute surface similaire qui
bloque les ouvertures de ventilation ; ne pas poser l’enceinte dans une meuble encastré ou fermé telle qu’une
bibliothèque ou un meuble qui empêche l’air de circuler par les ouvertures de ventilation de l’enceinte.
9. Chaleur - Placer l’enceinte loin de toute source de chaleur tels que radiateurs, compteurs thermiques, fours ou
autres enceintes dégageant de la chaleur.
10. Sources d’électricité - Ne brancher l’enceinte que dans une prise du type décrit dans le mode d’emploi ou
comme indiqué par le fabricant.
11. Protection du cordon électrique - Les cordons électriques doivent être fixés pour éviter que toute personne ne
marche dessus et que rien ne puisse être placé sur ou contre eux - faire tout particulièrement attention aux
cordons branchés dans des prises électriques, à des réceptacles et à leurs points de sorties de l’enceinte.
12. ”Attention : Afin d’éviter tout choc électrique, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond”.
13. Nettoyage - Pour le nettoyage de l’enceinte, suivre scrupuleusement les instructions du fabricant.
14. Périodes de non-utilisation - Le cordon électrique de l’enceinte doit rester débranché si l’enceinte reste
inutilisée pendant une longue période de temps.
15. Infiltration d’objet ou de liquide - Faire attention à ce qu’aucun objet ne tombe et à ce qu’aucun liquide ne soit
versé sur l’enceinte.
16. Dommages nécessitant réparation - L’enceinte ne doit être réparée que par du personnel qualifié lorsque :
a. le cordon électrique ou la prise ont été endommagés.
b. Des objets sont tombés ou du liquide a été versé sur l’enceinte.
c. L’enceinte a été exposée à la pluie.
d. L’enceinte ne semble pas fonctionner normalement ou indique un changement de performance.
e. L’enceinte est tombée par terre ou a été endommagée.
17. Entretien - L’utilisateur ne doit pas tenter de réparer l’enceinte au-delà de ce qui est décrit dans le mode
d’emploi.
18. Surcharge - Ne pas surcharger les prises murales, les rallonges, ou les prises femelles encastrées de
commodité. On risquerait un incendie ou un choc électrique.
19. Pièces de rechange - Lorsque le remplacement d’une pièce s’avère nécessaire, s’assurer que le technicien
utilise la pièce spécifiée par le fabriquant, ou une pièce possédant les mêmes caractéristiques que la pièce
d’origine. Les substitutions non autorisées peuvent provoquer des incendies ou des chocs électriques, ou
présenter d’autres dangers.
20. Contrôle de sécurité - Après toute intervention technique sur ce produit (neuf ou réparé), demander au
technicien de procéder à un contrôle de sécurité pour vérifier qu’il est en bon état de marche.
Toute autre réparation doit être référée à du personnel qualifié.
16
3
IMPORTANTES CONSIGNES DE SECURITE
ATTENTION
Risque d’électrocution
Ne pas ouvrir
SPECIFICATIONS SPL-800 Series II SPL-1000 Series II SPL-1200 Series II
Cabinet (H,W,D) 10.5" x 10.25" x 12.75" x 12.25" x 15" x 14.5" x
(incl. feet and grill) 12.5" 14.25" 16.25"
Frequency Response 28Hz - 120Hz 24Hz - 120Hz 22Hz - 120Hz
(+/-3 dB)
Harmonic Distortion <5% (typical) <5% (typical) <5% (typical)
High Pass Crossover 80Hz 80Hz 80Hz
(6 dB/octave) (6 dB/octave) (6 dB/octave)
Low Pass Crossover 40Hz - 120Hz 40Hz - 120Hz 40Hz - 120Hz
(12 dB/octave initial, 48 dB/octave ultimate)
Phase 0
°
or 180
°
0
°
or 180
°
0
°
or 180
°
Amplifier (Class D) 2000 watts Dynamic/ 2000 watts Dynamic/ 2000 watts Dynamic/
1000 watts RMS power 1000 watts RMS power 1000 watts RMS power
Woofer 8" 10" 12"
(forward firing) (6.5" Piston Diameter) (8" Piston Diameter) (9.7" Piston Diameter)
Magnetic Structure 204 oz. 346 oz. 346 oz.
(12.7 lbs.) (21.6 lbs.) (21.6 lbs.)
Voice Coil 2.5" Dual Layer 3" Dual Layer 3" Dual Layer
inner/outer wind inner/outer wind inner/outer wind
Inputs Line and Speaker Line and Speaker Line and Speaker
Level Level Level
Outputs Line-level, 80Hz up Line-level, 80Hz up Line level, 80Hz up
Magnetically Shielded No Yes Yes
Warranty (parts/labor) Two years Two years Two years
Weight (approx.) 35 lbs. 47 lbs. 57 lbs.
Specifications are subject to change without notice.
continued. . .
Congratulations!
Congratulations on your purchase of a Velodyne subwoofer system. This
system represents the state of the art in home audio reproduction and will
provide you with years of listening pleasure when properly cared for. Read
and follow this instruction manual to insure safe and proper system
connection and operation.
Caution!
Please observe the following instructions to insure safe and proper system
operation.
Note: Do not leave unit in direct sunlight or use in high humidity
environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture. To avoid electrical shock, do not open speaker enclosure or amp
chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to
your authorized Velodyne dealer.
Prior to installation-
Please unpack the system carefully. This unit is heavy. Use caution when
lifting or moving to avoid injury. Remove all staples used to seal the carton
as they can scratch the cabinet. Please save the carton and all packaging
materials for future use. Packing this unit in any other carton may result
in severe damage when shipping. Record the serial number in the space
provided on the warranty card or log onto www.velodyne.com.
continued. . .
15
4
Troubleshooting and Service
If you should experience a problem with the operation of your subwoofer,
please check all of the following before seeking service. Following is a
simple troubleshooting guide to assist you.
1. Verify unit is plugged in, power outlet used is active, and supplying
proper voltage.
2. Is power switch on?
3. Is auto turn on/off set properly?
4. Is unit receiving an input signal from your source?
5. Have all controls on subwoofer (volume, crossover, phase, etc.) been
properly set?
6. If unit has been running at high levels for an extended period of time,
one of the protection circuits may be engaged.
• Is the built-in amplifier extremely hot to the touch?
• Is your power line voltage sagging below acceptable levels?
If the protection circuitry is active, the unit may cycle on and off until
operating parameters return to normal. Under more serious conditions, the
unit may shut off completely. Normal operation should return upon
cooling, but you may be required to turn the power off and then on again
to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a marked
change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
• Signal sensing auto turn on/off (defeatable)
• Variable volume control
• Selectable phase control (0
°
or 180
°
)
• Frequency response of 28 - 120 Hz (SPL-800 Series II), 24 - 120Hz (SPL-
1000 Series II), 22-120Hz (SPL-1200 Series II)
• Magnetically shielded for video use (SPL-1000 Series II and SPL-1200
Series II)
• Multiple staggered low-pass crossovers; 12dB/octave initial, 48dB/
octave ultimate
• Driver Displacement Control circuit prevents over excursion and amp
clipping
• Blue power indicator LED
• High-excursion EPDM rubber surround
• Oversized spider for linearity at high excursion
Prepare for Installation
Your new Velodyne subwoofer provides for a number of installation
options. Read all the installation information below in order to determine
which installation option is best for your system. Remember to perform
all installation procedures with system power turned off to prevent
possible damage.
Placement
True subwoofers operate at extremely low frequencies which are primarily
omni-directional. While it is recommended that the subwoofer be placed
on the same plane as the satellite speakers, room and system conditions
often dictate otherwise. Keep in mind that frequency response and output
level can be drastically influenced by placement, depending on the
acoustic properties of the listening room. Typically, the optimum location
continued. . .
5
14
continued. . .
Product Features
• 8" (6.5" piston diameter) subwoofer with 2.5" high-temp voice coil and
107 ounce magnet/204 ounce motor structure; 10" (8" piston diameter)
or 12" (9.7" piston diameter) subwoofer with 3" voice coil and 162 ounce
magnet/346 ounce motor structure
• Built-in 2000 watts Dynamic/1000 watts RMS high efficiency class D
amplifier
• Adjustable (40 to 120Hz) low-pass crossover (defeatable)
• Line-level (RCA) inputs and outputs
• Speaker-level inputs with 5 way binding post connections
Care of Your Subwoofer
Your Velodyne subwoofer does not require any regular maintenance.
Normal dusting or cleaning of the surface for appearance purposes are all
that is required. We suggest you avoid any harsh detergents or chemicals
when cleaning the cabinet. Abrasives, detergents, or cleaning solutions
may damage the finish on the cabinet. We recommend using only a damp
cloth to clean the cabinet.
During normal conditions, your new subwoofer may be left on continuously
without any problems. The unit is equipped with a signal-sensing turn on/
off that will automatically turn on the unit when a signal is present at the
inputs and turn off the unit after several minutes when there is no longer
any signal at the inputs. If you plan to leave the subwoofer unused for an
extended period of time, we recommend that you turn off the master power
switch on the rear panel.
The unit is protected against:
1) Overdriving the speaker or amplifier.
2) Overheating the amplifier.
3) Excessive drop in power line voltage.
The first type of protection circuitry which prevents overdriving of the
speaker or amplifier operates constantly without being audible under most
situations. In some extreme situations (sustained high output levels such
as pro sound usage), the unit may shut down momentarily. This indicates
operation of the thermal or undervoltage protection circuitry. If this should
happen, you should reduce the volume setting or shut the unit off until
normal operating conditions return. You may also want to plug the unit
into a different wall outlet, as dropping power line voltage will be most
noticeable under strenuous conditions and may result in the unit shutting
down intermittently.
Protection Circuitry
Your new subwoofer is equipped with special protection circuitry to
provide maximum performance with greatest reliability.
strands or frayed wires which may result in a short, which may damage your
equipment. Cables of extremely large size are typically not required.
Extremely large gauge wire may not properly fit in the binding posts,
resulting in a poor connection and possible short circuits.
continued. . .
Regardless of where you install your Velodyne subwoofer, it must remain
in an upright position (woofer facing forward). Using, shipping, or
otherwise storing the subwoofer in any other position for an extended
period of time may result in damage to the unit not covered by warranty.
The SPL-1000 Series II and SPL-1200 Series II are magnetically shielded to
reduce the amount of stray magnetic energy emitted from the speaker's
motor structure. This greatly increases flexibility when placing the unit
close to video monitors as there is very little stray magnetism. Certain types
of televisions are particularly sensitive to stray magnetic fields. If your
television produces distorted colors after installing your subwoofer,
simply increase the distance between your television and the subwoofer,
until normal color and operation is returned.
Your new Velodyne subwoofer, like any good speaker system, requires
proper positioning within the listening space to provide maximum
performance. Improperly placed speakers may degrade the sound quality
and reduce your listening pleasure. Depending on the size and type of
furnishings in the room, perfect placement may not be possible. Finding
the best location for your environment will likely require some
experimentation. We suggest you experiment with the location during
setup to find what sounds best to you when seated in your typical listening
position.
continued. . .
13
6
for a subwoofer is tucked away in a corner of your listening room. This
location will usually offer the greatest output levels and optimum low
frequency extension. The worst location for a subwoofer is typically far
away from any walls, and close to the center of your room. Avoid these
locations when possible. When using a pair of Velodyne subwoofers in
stereo, it is preferable to place each subwoofer by the satellite of the same
channel.
Caution! This subwoofer has electronics built into the cabinet. Do not
place the cabinet next to sources of heat such as furnace registers,
radiators, etc. Do not place the unit near sources of excessive moisture,
such as evaporative coolers, humidifiers, etc. The power cord should be
routed in such a way that it will not be walked on, pinched, or compressed
in any way that could result in damaging the insulation or wire.
Figure 3. Installation Using Speaker-level Inputs
INTEGRATED AMP / RECEIVER
MAIN OUTPUTS
(speaker-level)
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
continued. . .
Installation
Inputs
Your new subwoofer is equipped with speaker-level and line-level inputs.
Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp,
signal processor, line-level crossover, or receiver with pre-amp level
outputs. The SPEAKER LEVEL jacks connect directly to the speaker
outputs of any amplifier, integrated amplifier, or receiver. Your amplifier
section will notice no additional loading effects when you use these inputs
due to their very high impedance.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections
simultaneously!
Volume control
This control allows you to balance the output from the subwoofer to the
main speakers/amplifier in your system. This control should be set to
achieve similar output level from both the main speakers and subwoofer
when listening to music. A good starting point for the volume control is
3 or 4 dots from minimum.
Low-pass crossover - 40 to 120Hz
All inputs sum the left and right channels together, with the resulting signal
passing through an adjustable low-pass crossover before being amplified.
The crossover control allows you to adjust the upper limit of the
subwoofer's frequency response from 40 to 120Hz. The subwoofer's
response will begin rolling off above the frequency you set this control to.
You should set the crossover frequency to obtain a smooth and seamless
transition from the subwoofer to the main speakers in your system. If your
main speakers are smaller units with limited low frequency output, you may
wish to choose a higher frequency (such as 100-120Hz) than you would
with larger speakers which have greater low frequency output. With larger
speakers, you might start with this control set lower, such as 80Hz.
A bypass switch is also provided if you wish to use an external crossover.
If you are not using an external crossover, we recommend that you use
the one provided within the unit for optimum performance!
Phase adjustment - 0
°
/180
°
This control allows you the "reverse" the phase of the subwoofer's output
signal 180
°
to correct for any possible mismatch and resulting cancellation
continued. . .
7
12
To bypass the subwoofer's internal crossover when the unit is being fed
a low pass signal from another crossover, simply locate the switch marked
INTERNAL X-OVER/SUBWOOFER DIRECT on the rear panel of the
subwoofer and set to the SUBWOOFER DIRECT position. This will
eliminate the internal crossover from the signal path.
Speaker-level Connection
Figure 3 shows an easy way to connect your Velodyne subwoofer directly
to your receiver or integrated amplifier, if it lacks line-level outputs. You
may also connect your satellites directly to your receiver or amplifier along
with the subwoofer. Your receiver or amplifier will not notice the additional
load of the suboofer due to the high input impedance.
Caution!!! To avoid damage to your main amplifier, be sure to maintain
correct polarity when making all connections. Red (positive) to red, and
black (negative) to black. Be sure that all connections are tight, and that
there are no loose strands or frayed wires.
Interconnect Cables
When installing your new Velodyne subwoofer using the line level
connections, you should always use shielded phono cables. There are
many decent cables available today, most any of which will work perfectly
well. We do recommend that you keep the length of cable as short as
possible to avoid any potential noise problems.
When using speaker level connections, use a decent quality speaker cable
that mates well with the connectors. Be very careful to avoid any loose
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Many home theater
processors/receivers (Dolby Digital, DTS, THX) have a "subwoofer out"
jack that is internally filtered and designed to be used with a powered
subwoofer. In these installations, you may bypass the internal crossover
in either the processor or the Velodyne subwoofer. In some installations,
it may be beneficial to have a steeper ultimate crossover slope. To do this,
you can use both your processor's crossover and the one internal to the
Velodyne sub. You should stagger the frequencies, (i.e., 120Hz sub, 80Hz
processor) for best results.
Subwoofer Outputs
continued. . .continued. . .
11
8
signal through external processors with a crossover circuit of their own,
such as the new digital units. Simply move the switch to SUBWOOFER
DIRECT to disengage the built in crossover. For all other installations
which do not have a separate electronic crossover, we recommend you
leave the switch set to INTERNAL X-OVER to provide optimum
performance.
Auto turn on function
With this function in the "auto" position, your subwoofer can be safely
left with the main power switch on continuously. The subwoofer will turn
itself on automatically when an audio signal is present. If no signal is
present for approximately 10 minutes, the unit will switch to standby mode.
While in standby mode, your subwoofer will draw very minimal power.
This function can be disabled by leaving the switch in the "on" position.
Power switch
The master power switch is located on the lower half of the unit. This rocker
style switch is the main on/off for the unit. This switch should be set to
position 1 (up) for on, and 0 (down) for off. If the unit is to be left unused
for an extended period of time, the master power switch should be turned
off.
Subwoofer outputs
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Some processors/
receivers, have a "subwoofer out" jack that is internally filtered and
designed to be used with a conventional amplifier and speaker. In some
rare cases, combining both an external crossover and the one internal to
the subwoofer may result in low output and increased noise. In these
installations you may need to bypass the internal crossover in either the
processor or Velodyne subwoofer. In some installations, simply setting
one crossover to a higher frequency (such as 120 Hz) will restore maximum
performance. To bypass the subwoofer's internal crossover when the unit
between the subwoofer and your main speakers/amplifier. To adjust,
simply listen to the system with music playing. Then move the switch from
one position to the other and listen for a change in low frequency output.
The correct position will have a greater amount of apparent low frequency
output.
Crossover switch - INTERNAL X-OVER/SUBWOOFER DIRECT
This switch allows the electronic crossover circuitry to be removed from
the signal path. This is required in certain installations which route the
Figure 2. Installation Using Stereo Line-level Inputs
AMPLIFIER
MAIN OUTPUTS
RIGHT LEFT
TO SATELLITE SPEAKERS
PRE-AMP
MAIN OUTPUTS
MAIN INPUTS
LEFT RIGHT
RIGHT
LEFT
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
continued. . .continued. . .
9
10
is being fed a low pass signal from another crossover, simply locate the
switch marked INTERNAL X-OVER/SUBWOOFER DIRECT on the rear
panel of the subwoofer and set to the SUBWOOFER DIRECT position.
This will eliminate the internal crossover from the signal path.
Note: If not using an external crossover, you should use the built-in
crossover for optimal performance.
Line-level Connection - Option A
Figure 1 shows connection from your home theater receiver to the LFE
input on the back of your subwoofer. When the subwoofer is installed in
this fashion, all of the low frequency information from your "LFE Out" or
"Subwoofer Out" on the back of your receiver will pass into your Velodyne
subwoofer. This connection is the most common connection method
when using your subwoofer with a 5.1 receiver. (Cable needed: 1 mono
RCA cable.)
Note: If not using an external crossover, you should use the built-in
crossover for optimal performance. When using a single channel input
(such as a surround sound processor's subwoofer out or LFE), the auto
on/off circuit sensitivity will be affected. When one input channel is used
instead of two, the unit will see lower signal levels present at the inputs.
This may cause the unit to turn off when listening at low volume levels.
If this occurs, simply use a "Y" adapter (available from most dealers) to
allow your processor's single sub line to be fed into both L&R inputs.
This will make the unit turn on at lower signal levels.
Figure 1. Installation Using LFE Line-Level Inputs
Home Theater
Receiver
LFE Out
Line-level Connection - Option B
Figure 2 shows connection from a pre-amplifier's main outputs to the left
and right inputs of your Velodyne subwoofer. You will also need to
connect a second pair of RCA cables from the outputs on the back of your
subwoofer to the inputs on the back of your amplifier. When the subwoofer
is installed in this fashion, your satellite speakers will be crossed over at
80Hz which removes the lower bass from frequencies from your external
amplifier and speakers, enabling them to do a better job reproducing the
higher frequencies. By utilizing this method, you will have a bi-amplified
system, gaining improved power and headroom for your system. This
installation method is not as common as the method described in Figure
1. (Cable needed: 2 stereo pair of RCA cables.)
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
continued. . .continued. . .
9
10
is being fed a low pass signal from another crossover, simply locate the
switch marked INTERNAL X-OVER/SUBWOOFER DIRECT on the rear
panel of the subwoofer and set to the SUBWOOFER DIRECT position.
This will eliminate the internal crossover from the signal path.
Note: If not using an external crossover, you should use the built-in
crossover for optimal performance.
Line-level Connection - Option A
Figure 1 shows connection from your home theater receiver to the LFE
input on the back of your subwoofer. When the subwoofer is installed in
this fashion, all of the low frequency information from your "LFE Out" or
"Subwoofer Out" on the back of your receiver will pass into your Velodyne
subwoofer. This connection is the most common connection method
when using your subwoofer with a 5.1 receiver. (Cable needed: 1 mono
RCA cable.)
Note: If not using an external crossover, you should use the built-in
crossover for optimal performance. When using a single channel input
(such as a surround sound processor's subwoofer out or LFE), the auto
on/off circuit sensitivity will be affected. When one input channel is used
instead of two, the unit will see lower signal levels present at the inputs.
This may cause the unit to turn off when listening at low volume levels.
If this occurs, simply use a "Y" adapter (available from most dealers) to
allow your processor's single sub line to be fed into both L&R inputs.
This will make the unit turn on at lower signal levels.
Figure 1. Installation Using LFE Line-Level Inputs
Home Theater
Receiver
LFE Out
Line-level Connection - Option B
Figure 2 shows connection from a pre-amplifier's main outputs to the left
and right inputs of your Velodyne subwoofer. You will also need to
connect a second pair of RCA cables from the outputs on the back of your
subwoofer to the inputs on the back of your amplifier. When the subwoofer
is installed in this fashion, your satellite speakers will be crossed over at
80Hz which removes the lower bass from frequencies from your external
amplifier and speakers, enabling them to do a better job reproducing the
higher frequencies. By utilizing this method, you will have a bi-amplified
system, gaining improved power and headroom for your system. This
installation method is not as common as the method described in Figure
1. (Cable needed: 2 stereo pair of RCA cables.)
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
continued. . .continued. . .
11
8
signal through external processors with a crossover circuit of their own,
such as the new digital units. Simply move the switch to SUBWOOFER
DIRECT to disengage the built in crossover. For all other installations
which do not have a separate electronic crossover, we recommend you
leave the switch set to INTERNAL X-OVER to provide optimum
performance.
Auto turn on function
With this function in the "auto" position, your subwoofer can be safely
left with the main power switch on continuously. The subwoofer will turn
itself on automatically when an audio signal is present. If no signal is
present for approximately 10 minutes, the unit will switch to standby mode.
While in standby mode, your subwoofer will draw very minimal power.
This function can be disabled by leaving the switch in the "on" position.
Power switch
The master power switch is located on the lower half of the unit. This rocker
style switch is the main on/off for the unit. This switch should be set to
position 1 (up) for on, and 0 (down) for off. If the unit is to be left unused
for an extended period of time, the master power switch should be turned
off.
Subwoofer outputs
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Some processors/
receivers, have a "subwoofer out" jack that is internally filtered and
designed to be used with a conventional amplifier and speaker. In some
rare cases, combining both an external crossover and the one internal to
the subwoofer may result in low output and increased noise. In these
installations you may need to bypass the internal crossover in either the
processor or Velodyne subwoofer. In some installations, simply setting
one crossover to a higher frequency (such as 120 Hz) will restore maximum
performance. To bypass the subwoofer's internal crossover when the unit
between the subwoofer and your main speakers/amplifier. To adjust,
simply listen to the system with music playing. Then move the switch from
one position to the other and listen for a change in low frequency output.
The correct position will have a greater amount of apparent low frequency
output.
Crossover switch - INTERNAL X-OVER/SUBWOOFER DIRECT
This switch allows the electronic crossover circuitry to be removed from
the signal path. This is required in certain installations which route the
Figure 2. Installation Using Stereo Line-level Inputs
AMPLIFIER
MAIN OUTPUTS
RIGHT LEFT
TO SATELLITE SPEAKERS
PRE-AMP
MAIN OUTPUTS
MAIN INPUTS
LEFT RIGHT
RIGHT
LEFT
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
continued. . .
Installation
Inputs
Your new subwoofer is equipped with speaker-level and line-level inputs.
Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp,
signal processor, line-level crossover, or receiver with pre-amp level
outputs. The SPEAKER LEVEL jacks connect directly to the speaker
outputs of any amplifier, integrated amplifier, or receiver. Your amplifier
section will notice no additional loading effects when you use these inputs
due to their very high impedance.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections
simultaneously!
Volume control
This control allows you to balance the output from the subwoofer to the
main speakers/amplifier in your system. This control should be set to
achieve similar output level from both the main speakers and subwoofer
when listening to music. A good starting point for the volume control is
3 or 4 dots from minimum.
Low-pass crossover - 40 to 120Hz
All inputs sum the left and right channels together, with the resulting signal
passing through an adjustable low-pass crossover before being amplified.
The crossover control allows you to adjust the upper limit of the
subwoofer's frequency response from 40 to 120Hz. The subwoofer's
response will begin rolling off above the frequency you set this control to.
You should set the crossover frequency to obtain a smooth and seamless
transition from the subwoofer to the main speakers in your system. If your
main speakers are smaller units with limited low frequency output, you may
wish to choose a higher frequency (such as 100-120Hz) than you would
with larger speakers which have greater low frequency output. With larger
speakers, you might start with this control set lower, such as 80Hz.
A bypass switch is also provided if you wish to use an external crossover.
If you are not using an external crossover, we recommend that you use
the one provided within the unit for optimum performance!
Phase adjustment - 0
°
/180
°
This control allows you the "reverse" the phase of the subwoofer's output
signal 180
°
to correct for any possible mismatch and resulting cancellation
continued. . .
7
12
To bypass the subwoofer's internal crossover when the unit is being fed
a low pass signal from another crossover, simply locate the switch marked
INTERNAL X-OVER/SUBWOOFER DIRECT on the rear panel of the
subwoofer and set to the SUBWOOFER DIRECT position. This will
eliminate the internal crossover from the signal path.
Speaker-level Connection
Figure 3 shows an easy way to connect your Velodyne subwoofer directly
to your receiver or integrated amplifier, if it lacks line-level outputs. You
may also connect your satellites directly to your receiver or amplifier along
with the subwoofer. Your receiver or amplifier will not notice the additional
load of the suboofer due to the high input impedance.
Caution!!! To avoid damage to your main amplifier, be sure to maintain
correct polarity when making all connections. Red (positive) to red, and
black (negative) to black. Be sure that all connections are tight, and that
there are no loose strands or frayed wires.
Interconnect Cables
When installing your new Velodyne subwoofer using the line level
connections, you should always use shielded phono cables. There are
many decent cables available today, most any of which will work perfectly
well. We do recommend that you keep the length of cable as short as
possible to avoid any potential noise problems.
When using speaker level connections, use a decent quality speaker cable
that mates well with the connectors. Be very careful to avoid any loose
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Many home theater
processors/receivers (Dolby Digital, DTS, THX) have a "subwoofer out"
jack that is internally filtered and designed to be used with a powered
subwoofer. In these installations, you may bypass the internal crossover
in either the processor or the Velodyne subwoofer. In some installations,
it may be beneficial to have a steeper ultimate crossover slope. To do this,
you can use both your processor's crossover and the one internal to the
Velodyne sub. You should stagger the frequencies, (i.e., 120Hz sub, 80Hz
processor) for best results.
Subwoofer Outputs
continued. . .
Regardless of where you install your Velodyne subwoofer, it must remain
in an upright position (woofer facing forward). Using, shipping, or
otherwise storing the subwoofer in any other position for an extended
period of time may result in damage to the unit not covered by warranty.
The SPL-1000 Series II and SPL-1200 Series II are magnetically shielded to
reduce the amount of stray magnetic energy emitted from the speaker's
motor structure. This greatly increases flexibility when placing the unit
close to video monitors as there is very little stray magnetism. Certain types
of televisions are particularly sensitive to stray magnetic fields. If your
television produces distorted colors after installing your subwoofer,
simply increase the distance between your television and the subwoofer,
until normal color and operation is returned.
Your new Velodyne subwoofer, like any good speaker system, requires
proper positioning within the listening space to provide maximum
performance. Improperly placed speakers may degrade the sound quality
and reduce your listening pleasure. Depending on the size and type of
furnishings in the room, perfect placement may not be possible. Finding
the best location for your environment will likely require some
experimentation. We suggest you experiment with the location during
setup to find what sounds best to you when seated in your typical listening
position.
continued. . .
13
6
for a subwoofer is tucked away in a corner of your listening room. This
location will usually offer the greatest output levels and optimum low
frequency extension. The worst location for a subwoofer is typically far
away from any walls, and close to the center of your room. Avoid these
locations when possible. When using a pair of Velodyne subwoofers in
stereo, it is preferable to place each subwoofer by the satellite of the same
channel.
Caution! This subwoofer has electronics built into the cabinet. Do not
place the cabinet next to sources of heat such as furnace registers,
radiators, etc. Do not place the unit near sources of excessive moisture,
such as evaporative coolers, humidifiers, etc. The power cord should be
routed in such a way that it will not be walked on, pinched, or compressed
in any way that could result in damaging the insulation or wire.
Figure 3. Installation Using Speaker-level Inputs
INTEGRATED AMP / RECEIVER
MAIN OUTPUTS
(speaker-level)
+ R - - L +
SPEAKER LEVEL
OFF
POWER
ON
LOW-PASS
CROSSOVER
40 Hz
80 Hz
120 Hz
SUBWOOFER
VOLUME
MIN
MAX
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
0
180
PHASE
0
0
POWER
ON
AUTO
LONG THROW DRIVER
HIGH-TEMP VOICE COIL
1000 WATTS CONTINUOUS POWER
DYNAMIC DRIVER CONTROL
ULTRA EFFICIENT CLASS D AMP
SUBWOOFER
DIRECT
INTERNAL
X-OVER
117V~
60Hz
8A
OUTPUT
INPUT
R
L
LFE
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
VELODYNE ACOUSTICS, INC.
SERIAL #
SPL Series
TM
II
I
O
• Signal sensing auto turn on/off (defeatable)
• Variable volume control
• Selectable phase control (0
°
or 180
°
)
• Frequency response of 28 - 120 Hz (SPL-800 Series II), 24 - 120Hz (SPL-
1000 Series II), 22-120Hz (SPL-1200 Series II)
• Magnetically shielded for video use (SPL-1000 Series II and SPL-1200
Series II)
• Multiple staggered low-pass crossovers; 12dB/octave initial, 48dB/
octave ultimate
• Driver Displacement Control circuit prevents over excursion and amp
clipping
• Blue power indicator LED
• High-excursion EPDM rubber surround
• Oversized spider for linearity at high excursion
Prepare for Installation
Your new Velodyne subwoofer provides for a number of installation
options. Read all the installation information below in order to determine
which installation option is best for your system. Remember to perform
all installation procedures with system power turned off to prevent
possible damage.
Placement
True subwoofers operate at extremely low frequencies which are primarily
omni-directional. While it is recommended that the subwoofer be placed
on the same plane as the satellite speakers, room and system conditions
often dictate otherwise. Keep in mind that frequency response and output
level can be drastically influenced by placement, depending on the
acoustic properties of the listening room. Typically, the optimum location
continued. . .
5
14
continued. . .
Product Features
• 8" (6.5" piston diameter) subwoofer with 2.5" high-temp voice coil and
107 ounce magnet/204 ounce motor structure; 10" (8" piston diameter)
or 12" (9.7" piston diameter) subwoofer with 3" voice coil and 162 ounce
magnet/346 ounce motor structure
• Built-in 2000 watts Dynamic/1000 watts RMS high efficiency class D
amplifier
• Adjustable (40 to 120Hz) low-pass crossover (defeatable)
• Line-level (RCA) inputs and outputs
• Speaker-level inputs with 5 way binding post connections
Care of Your Subwoofer
Your Velodyne subwoofer does not require any regular maintenance.
Normal dusting or cleaning of the surface for appearance purposes are all
that is required. We suggest you avoid any harsh detergents or chemicals
when cleaning the cabinet. Abrasives, detergents, or cleaning solutions
may damage the finish on the cabinet. We recommend using only a damp
cloth to clean the cabinet.
During normal conditions, your new subwoofer may be left on continuously
without any problems. The unit is equipped with a signal-sensing turn on/
off that will automatically turn on the unit when a signal is present at the
inputs and turn off the unit after several minutes when there is no longer
any signal at the inputs. If you plan to leave the subwoofer unused for an
extended period of time, we recommend that you turn off the master power
switch on the rear panel.
The unit is protected against:
1) Overdriving the speaker or amplifier.
2) Overheating the amplifier.
3) Excessive drop in power line voltage.
The first type of protection circuitry which prevents overdriving of the
speaker or amplifier operates constantly without being audible under most
situations. In some extreme situations (sustained high output levels such
as pro sound usage), the unit may shut down momentarily. This indicates
operation of the thermal or undervoltage protection circuitry. If this should
happen, you should reduce the volume setting or shut the unit off until
normal operating conditions return. You may also want to plug the unit
into a different wall outlet, as dropping power line voltage will be most
noticeable under strenuous conditions and may result in the unit shutting
down intermittently.
Protection Circuitry
Your new subwoofer is equipped with special protection circuitry to
provide maximum performance with greatest reliability.
strands or frayed wires which may result in a short, which may damage your
equipment. Cables of extremely large size are typically not required.
Extremely large gauge wire may not properly fit in the binding posts,
resulting in a poor connection and possible short circuits.
continued. . .
Congratulations!
Congratulations on your purchase of a Velodyne subwoofer system. This
system represents the state of the art in home audio reproduction and will
provide you with years of listening pleasure when properly cared for. Read
and follow this instruction manual to insure safe and proper system
connection and operation.
Caution!
Please observe the following instructions to insure safe and proper system
operation.
Note: Do not leave unit in direct sunlight or use in high humidity
environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture. To avoid electrical shock, do not open speaker enclosure or amp
chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to
your authorized Velodyne dealer.
Prior to installation-
Please unpack the system carefully. This unit is heavy. Use caution when
lifting or moving to avoid injury. Remove all staples used to seal the carton
as they can scratch the cabinet. Please save the carton and all packaging
materials for future use. Packing this unit in any other carton may result
in severe damage when shipping. Record the serial number in the space
provided on the warranty card or log onto www.velodyne.com.
continued. . .
15
4
Troubleshooting and Service
If you should experience a problem with the operation of your subwoofer,
please check all of the following before seeking service. Following is a
simple troubleshooting guide to assist you.
1. Verify unit is plugged in, power outlet used is active, and supplying
proper voltage.
2. Is power switch on?
3. Is auto turn on/off set properly?
4. Is unit receiving an input signal from your source?
5. Have all controls on subwoofer (volume, crossover, phase, etc.) been
properly set?
6. If unit has been running at high levels for an extended period of time,
one of the protection circuits may be engaged.
• Is the built-in amplifier extremely hot to the touch?
• Is your power line voltage sagging below acceptable levels?
If the protection circuitry is active, the unit may cycle on and off until
operating parameters return to normal. Under more serious conditions, the
unit may shut off completely. Normal operation should return upon
cooling, but you may be required to turn the power off and then on again
to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a marked
change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
continued. . .
Attention: Afin d’éviter tout risque d’électrocution, ne pas enlever le boitier (ou partie arrière de
l’enceinte). Aucune pièce ne doit être manipulée par l’utilisateur. Pour tout entretien, vous référer à un
personnel de service qualifié.
Le symbol de l’éclair avec la flèche sert à avertir l’utilisateur de la présence d’un “voltage dangereux”
non isolé dans l’enceinte du produit d’une magnitude pouvant constituer un risque
d’électrocution de personnes.
Le symbol du point d’exclamation sert à avertir l’utilisateur que d’importants conseils de fonctionnement
et de maintenance (entretien) sont fournis avec l’enceinte d’extrêmes graves.
1. Lire le mode d’emploi - Tous les conseils de sécurité et de fonctionnement doivent être lus avant de mettre en
marche l’enceinte.
2. Garder le mode d’emploi - Il est conseillé de conserver les conseils de sécurité et de fonctionnement pour un
éventuel usage futur.
3. Avertissements - Il est important de se conformer à tous les conseils de fonctionnement concernant l’enceinte
et à toutes les instructions inscrites sur l’enceinte.
4. Suivre les conseils - Tous les conseils d’utilisation et de fonctionnement doivent être suivis à la règle.
5. Eau et humidité - Ne pas utiliser l’enceinte près d’une source d’eau - par exemple, près de la baignoire, d’une
bassine de lavage, d’un évier de cuisine, d’un bac à lavage, dans un sous-seul mouillé, près d’une piscine…
6. Pieds et Supports - N’utiliser que des pieds et supports recommandés par le fabricant.
7. Assemblage mural ou au plafond - Se conformer uniquement aux instructions du fabricant pour fixer l’enceinte
sur un mur ou sur un plafond.
8. Ventilation - Il est important de placer l’enceinte de telle sorte qu’elle ne gêne pas sa propre ventilation. Par
exemple, ne pas placer l’enceinte sur un lit, un canapé, sur la moquette, ou sur toute surface similaire qui
bloque les ouvertures de ventilation ; ne pas poser l’enceinte dans une meuble encastré ou fermé telle qu’une
bibliothèque ou un meuble qui empêche l’air de circuler par les ouvertures de ventilation de l’enceinte.
9. Chaleur - Placer l’enceinte loin de toute source de chaleur tels que radiateurs, compteurs thermiques, fours ou
autres enceintes dégageant de la chaleur.
10. Sources d’électricité - Ne brancher l’enceinte que dans une prise du type décrit dans le mode d’emploi ou
comme indiqué par le fabricant.
11. Protection du cordon électrique - Les cordons électriques doivent être fixés pour éviter que toute personne ne
marche dessus et que rien ne puisse être placé sur ou contre eux - faire tout particulièrement attention aux
cordons branchés dans des prises électriques, à des réceptacles et à leurs points de sorties de l’enceinte.
12. ”Attention : Afin d’éviter tout choc électrique, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond”.
13. Nettoyage - Pour le nettoyage de l’enceinte, suivre scrupuleusement les instructions du fabricant.
14. Périodes de non-utilisation - Le cordon électrique de l’enceinte doit rester débranché si l’enceinte reste
inutilisée pendant une longue période de temps.
15. Infiltration d’objet ou de liquide - Faire attention à ce qu’aucun objet ne tombe et à ce qu’aucun liquide ne soit
versé sur l’enceinte.
16. Dommages nécessitant réparation - L’enceinte ne doit être réparée que par du personnel qualifié lorsque :
a. le cordon électrique ou la prise ont été endommagés.
b. Des objets sont tombés ou du liquide a été versé sur l’enceinte.
c. L’enceinte a été exposée à la pluie.
d. L’enceinte ne semble pas fonctionner normalement ou indique un changement de performance.
e. L’enceinte est tombée par terre ou a été endommagée.
17. Entretien - L’utilisateur ne doit pas tenter de réparer l’enceinte au-delà de ce qui est décrit dans le mode
d’emploi.
18. Surcharge - Ne pas surcharger les prises murales, les rallonges, ou les prises femelles encastrées de
commodité. On risquerait un incendie ou un choc électrique.
19. Pièces de rechange - Lorsque le remplacement d’une pièce s’avère nécessaire, s’assurer que le technicien
utilise la pièce spécifiée par le fabriquant, ou une pièce possédant les mêmes caractéristiques que la pièce
d’origine. Les substitutions non autorisées peuvent provoquer des incendies ou des chocs électriques, ou
présenter d’autres dangers.
20. Contrôle de sécurité - Après toute intervention technique sur ce produit (neuf ou réparé), demander au
technicien de procéder à un contrôle de sécurité pour vérifier qu’il est en bon état de marche.
Toute autre réparation doit être référée à du personnel qualifié.
16
3
IMPORTANTES CONSIGNES DE SECURITE
ATTENTION
Risque d’électrocution
Ne pas ouvrir
SPECIFICATIONS SPL-800 Series II SPL-1000 Series II SPL-1200 Series II
Cabinet (H,W,D) 10.5" x 10.25" x 12.75" x 12.25" x 15" x 14.5" x
(incl. feet and grill) 12.5" 14.25" 16.25"
Frequency Response 28Hz - 120Hz 24Hz - 120Hz 22Hz - 120Hz
(+/-3 dB)
Harmonic Distortion <5% (typical) <5% (typical) <5% (typical)
High Pass Crossover 80Hz 80Hz 80Hz
(6 dB/octave) (6 dB/octave) (6 dB/octave)
Low Pass Crossover 40Hz - 120Hz 40Hz - 120Hz 40Hz - 120Hz
(12 dB/octave initial, 48 dB/octave ultimate)
Phase 0
°
or 180
°
0
°
or 180
°
0
°
or 180
°
Amplifier (Class D) 2000 watts Dynamic/ 2000 watts Dynamic/ 2000 watts Dynamic/
1000 watts RMS power 1000 watts RMS power 1000 watts RMS power
Woofer 8" 10" 12"
(forward firing) (6.5" Piston Diameter) (8" Piston Diameter) (9.7" Piston Diameter)
Magnetic Structure 204 oz. 346 oz. 346 oz.
(12.7 lbs.) (21.6 lbs.) (21.6 lbs.)
Voice Coil 2.5" Dual Layer 3" Dual Layer 3" Dual Layer
inner/outer wind inner/outer wind inner/outer wind
Inputs Line and Speaker Line and Speaker Line and Speaker
Level Level Level
Outputs Line-level, 80Hz up Line-level, 80Hz up Line level, 80Hz up
Magnetically Shielded No Yes Yes
Warranty (parts/labor) Two years Two years Two years
Weight (approx.) 35 lbs. 47 lbs. 57 lbs.
Specifications are subject to change without notice.
Vorsicht: Zur Vermeidung von Gefahr durch elektrischen Schlag, Deckel (oder Rückwand) nicht
abnehmen. Produkt enthält keine Anwenderteile. Reparatur und Wartung nur von qualifiziertem
Fachpersonal vornehmen lassen.
Das Blitzsymbol dient als Hinweis auf unisolierte „gefährliche Spannungen“ innerhalb des Gehäuses,
deren Werte eine Berührungsgefahr für den Menschen darstellen können.
Das Symbol mit dem Ausrufungszeichen dient als Hinweis auf wichtige, in den Unterlagen des Subwoofers
enthaltene Bedienungs- und Wartungsvorschriften.
1. Anleitungen lesen - Alle Sicherheits- und Bedienungsanleitungen vor Inbetriebnahme des Subwoofers aufmerksam
durchlesen.
2. Anleitungen aufbewahren - Die Sicherheits- und Bedienungsanleitungen zur späteren Bezugnahme aufbewahren.
3. Warnungen beachten - Alle Warnungen am Subwoofer und in der Bedienungsanleitung unbedingt beachten.
4. Anleitungen befolgen - Alle Bedienungs- und Gebrauchsanleitungen genau befolgen.
5. Wasser und Feuchtigkeit - Subwoofer nicht in der Nähe von Wasser aufstellen, d.h. neben einer Badewanne,
Spüle, Waschmaschine, in einem feuchten Keller, in der Nähe des Swimmingpools o.ä..
6. Rollwagen und Ständer - Subwoofer nur mit einem vom Hersteller empfohlenen Rollwagen oder Ständer benutzen.
7. Wand- oder Deckenbefestigung - Subwoofer nur den Herstellerempfehlungen gemäß an der Wand oder Decke
befestigen.
8. Belüftung - Subwoofer so aufstellen, daß die erforderliche Belüftung nicht behindert wird. D.h., Subwoofer nicht auf
einer weichen Oberfläche wie einem Bett, Sofa, Teppich o.ä. aufstellen, die die Belüftungsöffnungen blockieren
kann. Subwoofer gleichfalls nicht in einem Regal oder Schrank unterbringen, worin die Luftzufuhr behindert wird.
9. Wärme - Subwoofer nicht in der Nähe von Wärmequellen, wie Heizkörpern, Wärmespeichern, Öfen oder anderen
wärmeerzeugenden Subwoofern aufstellen.
10. Netzanschluß - Subwoofer nur an eine der in der Bedienungsanleitung beschriebenen oder auf dem Subwoofer
angegebenen Stromquellen anschließen.
11. Netzkabelschutz - Netzkabel so verlegen, daß nicht daraufgetreten wird oder sie durch darauf-oder
dagegengestellte Gegenstände eingeklemmt werden können. Die Anschlußstellen des Netzkabels an Steckdosen
und am Subwoofer dabei besonders beachten.
12. „Vorsicht“: Zur Vermeidung von Gefahr durch elektrischen Schlag sicherstellen, daß der Schutzkontakt
des Steckers vollständig in die Steckdose eingeführt ist.
13. Reinigung - Subwoofer nur den Herstellerempfehlungen gemäß reinigen.
14. Betriebsfreie Zeiträume - Netzkabel des Subwoofers aus der Steckdose ziehen, wenn er über einen längeren
Zeitraum nicht benutzt wird.
15. Beschädigungen durch Gegenstände oder Flüssigkeiten - Es ist darauf zu achten, daß keine Gegenstände auf
das Gehäuse fallen oder Flüssigkeiten darauf verschüttet werden.
16. Beschädigungen, die eine Reparatur erforderlich machen - Subwoofer sollte von qualifiziertem Fachpersonal
repariert werden, wenn:
a. Das Netzkabel oder der Stecker beschädigt sind.
b. Gegenstände oder Flüssigkeiten in den Subwoofer gelangt sind.
c. Der Subwoofer dem Regen ausgesetzt wurde.
d. Der Betrieb des Subwoofers gestört ist oder seine Leistung deutlich nachgelassen hat.
e. Der Subwoofer fallengelassen oder beschädigt wurde.
17. Reparatur und Wartung - Durch den Benutzer auszuführende Wartungsmaßnahmen des Subwoofers sind auf die
in der Bedienungsanleitung angegebenen Prozeduren beschränkt.
18. Überlastung - Zur Vermeidung von Brandgefahr und elektrischem Schlag Wandsteckdosen,
Verlängerungskabel bzw. eingebaute Steckdosen nicht überlasten.
19. Ersatzteile - Wenn Ersatzteile benötigt werden, sicherstellen, daß der Servicetechniker entweder die vom
Hersteller angegebenen Ersatzteile benutzt oder Teile, die den Originalteilen entsprechende Kennwerte
besitzen. Die Verwendung von Ersatzteilen, die nicht zugelassen sind, kann Brände, elektrischen Schlag
oder andere Gefahren verursachen.
20. Sicherheitsprüfung - Nach Beendigung von Wartungs- oder Reparaturmaßnahmen an diesem Produkt vom
Servicetechniker Sicherheitsprüfungen zum Nachweis des ordnungsgemäßen Betriebszustandes vornehmen
lassen.
Alle anderweitigen Servicemaßnahmen von qualifiziertem Wartungspersonal durchführen lassen.
17
2
WICHTIGE SICHERHEITSHINWEISE
VORSICHT
GEFÄHRLICHE SPANNUNG
NICHT ÖFFNEN
Thank You for Purchasing an
SPL Series II Velodyne Subwoofer!
* NOTE: Please complete and return your warranty card within ten (10) days
or
Register
....
ON-LINE
.....
It's faster.....and easier
www.velodyne.com
FOR YOUR RECORDS. . .
DATE PURCHASED
____________________________________
DEALER
__________________________________________________
SERIAL #
_____________________________________________
Other Velodyne Subwoofer Products:
Digital Drive 1812
Digital Drive Series
DD-10
DD-12
DD-15 THX Ultra 2
DD-18 THX Ultra 2
Deco System
Deco System
Deco Satellites
CHT Series
CHT-8
CHT-10
CHT-12
CHT-15
CHT Front Row System
VX-10
DLS Series
DLS-3500
DLS-3750
DLS-4000
TM
TM
TM
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel.
The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated.
2. Retain Instructions -- The safety and operating instructions should be retained for future reference.
3. Heed Warnings -- All warnings on the subwoofer and in the operating instructions should be adhered to.
4. Follow Instructions -- All operating and use instructions should be followed.
5. Water and Moisture -- The subwoofer should
not
be used near water -- for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, near a swimming pool, or the like.
6. Carts and Stands -- The subwoofer should be used only with a cart or stand recommended by the manufacturer
to avoid injury from tipover.
7. Wall or Ceiling Mounting -- The subwoofer should be mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Ventilation -- The subwoofer should be situated so that its location or position does not interfere with its proper
ventilation. For example, the subwoofer should not be situated on a bed, sofa, rug, or similar surface that
may block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9. Heat -- The subwoofer should be situated away from heat sources such as radiators, heat registers, stoves,
or other subwoofers that produce heat.
10. Power Sources -- The subwoofer should be connected to a power supply only of the type described in the
operating instructions or as marked on the subwoofer.
11. Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point at which they exit from the subwoofer.
12. Caution: To prevent electrical shock, match wide blade of plug to wide slot, fully inserted.
13. Cleaning -- The subwoofer should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods -- The power cord of the subwoofer should be unplugged from the outlet when left unused for
a long period of time.
15. Object and Liquid Entry -- Care should be taken so that objects do not fall and liquids are not spilled onto the
enclosure.
16. Damage Requiring Service -- The subwoofer should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen or liquid has been spilled into the subwoofer.
c. The subwoofer has been exposed to rain.
d. The subwoofer does not appear to operate normally or exhibits a marked change in performance.
e. The subwoofer has been dropped or damaged.
17. Servicing -- The user should not attempt to service the subwoofer beyond what is described in the operating
instructions.
18. Overloading -- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19. Replacement parts -- When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
20. Safety Check -- Upon completion of any service or service of repairs to this product, ask the service technician
to perform safety checks to determine that the product is in proper operating condition.
All other servicing should be referred to qualified service personnel.
18
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1
NOTES
Home Theater Subwoofer
SPL-800, SPL-1000,
and SPL-1200
Series II
Owner's Manual
Velodyne Acoustics, Inc.
345 Digital Drive
Morgan Hill, CA 95037
408.465.2800 voice
408.779.9227 fax
408.779.9208 Service fax
Web Site: www.velodyne.com
Service E-mail: [email protected]
Product E-mail: [email protected]
Technical E-mail: [email protected]
"
Not only was the little Velodyne the best
small
sub I've ever used,
it was one of the very best subs I've used.
"
-John Potis
SoundStage!, April 2002
"The SPL-1200 was able to hit an impressively deep 16 Hz."
-
Tom Noussaine
Sound & Vision, June 2001
"How do they get this kind of bass out of such a tiny box? Deep, tight,
tuneful and loud enough to rattle pictures on the wall--this is serious
subwoofing."
-Robert Deutsch
Stereophile Guide to Home Theater, September 1998
Printed on recycled paper
63-SPLII RevA 04/03
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Velodyne Acoustics Speaker System SPL-1000 Manuel utilisateur

Catégorie
Subwoofers
Taper
Manuel utilisateur
Ce manuel convient également à