Risco VUpoint RVCM32W Guide d'installation

VUpoint

Dome Vandal-Proof P2P

IP Camera

Model: RVCM32W

EN

FR

IT

ES

Installation Guide

Language Page

1

25

50

71

VUpoint

Dome Vandal-Proof P2P

IP Camera

Model: RVCM32W

EN

http://VUpoint-P2P.riscogroup.com/How-to-Install/

Installation Guide

2

Safety Precautions

These instructions are intended to ensure that the user can use the product correctly to

avoid danger or property loss.

WARNINGS:

 Installation or usage of this product that is not in accordance with the intended

use as defined by the supplier and as described in the instructional materials

can result in damage, injury, or death.

 Make sure this product is not accessible by children and those for whom

operation of the system is not intended.

 All installation and operation should conform to your local electrical safety

codes. The power shall conform to the requirement in the SELV (Safety Extra

Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1.

 If the device is permanently connected to an electrical power supply, then the

connection should include an easily-accessible disconnection device, such as a

circuit breaker. Do not connect the two power supplying sources to the device

at the same time; it may result in device damage!

 Do not ever attempt to repair your device by yourself, as doing so could result

in damage, injury or death – always contact your installer / supplier agent for

service.

CAUTIONS:

 Make sure the power supply voltage is correct before using the camera.

 Do not drop the camera or subject it to physical shock.

 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean

cloth with a bit of ethanol and wipe it gently.

 Do not aim the camera lens at the strong light such as sun or incandescent

lamp. The strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is

being used, make sure that the surface of the sensor not be exposed to the laser

beam.

 Do not place the camera in extremely hot, cold temperatures (the operating

temperature should be between -10°C ~ +50°C).

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 While shipping, the camera should be packed in its original packing.

NOTE: We assume no liability or responsibility for all the fires or electrical shock

caused by improper handling or installation. We are not liable for any problems caused

by unauthorized modification or attempted repair.

3

Introduction

RISCO Group presents VUpoint, a revolutionary live video verification solution

which seamlessly integrates IP Cameras within RISCO’s professional security

systems. Powered by the RISCO Cloud (RISCO Application Server), VUpoint

provides an unprecedented level of security and live video monitoring

capabilities to monitoring stations and end-users alike. The RISCO dome indoor

and outdoor IP Camera is an important part of this solution and

is easily

controlled through RISCO’s intuitive Web and Smartphone applications.

Features

 Plug & Play installation

 1.3 Megapixel

 Color HD

 Day/Night

 IR LED Length 30m

Components and Accessories

RISCO IP camera and

mounting bracket:

Installation guide:

4

IP Camera Components and Dimensions

Figure 1 External View and Ports

Label Name

1

Dome cover

2

Dome enclosure

3

Network port

4

Power port

5

Figure 2 IP Camera Components

Label Name

1

Wireless antenna

2

Waterproof ring

3

Reset/ WPS (Wi-Fi Protected Setup) button

4

Micro SD card slot

5

Indicator light 1

6

Indicator light 2

Note:

 For reset (used to return the camera settings to factory default mode), long

press for 15 seconds and then the light turns off

 For WPS (Wi-Fi Protected Setup), one quick press.

6

Indication Status

Red light normally on

Booting

Green light slow

flashing

IP Camera is not connected to the RISCO Cloud. Please check

for internet connection and try to connect again by rebooting

the IP Camera.

Green light quick

flashing

WiFi smart config in progress, including WPS (WiFi Protected

Setup), management frame and etc.

Green light normally

on

IP Camera is successfully connected to the RISCO Cloud.

Red and green lights

flash alternately

Device upgrade

Red light slow flashing

Network connection failure or disconnection after network

connection success.

Red light quick

flashing

Device malfunction, fail to boot up; alarm or SD card

malfunction

Figure 3 IP Camera Dimensions

7

IP Camera Installation

After reading the installation instructions and before installing your IP camera,

prepare a plan for mounting the IP camera at your protected site. Correct

placement of your IP camera is crucial for optimal security-monitoring

performance. First, determine which areas need to be protected and then map

out the most optimal areas for installing your IP camera.

IMPORTANT! – Please make a record of the MAC

address located on the box or on the back cover of

the IP camera before installation. You may need it

during the network connection stage.

MAC address

8

Mounting the IP Camera

Figure 4 Mounting

IMPORTANT- Please make sure the installation surface can support at least 3

times the weight of the camera and the bracket.

Step Description

1

Use the supplied hex wrench to open the dome enclosure by releasing the three

inner hex screws.

2

Place the installation positioning template on the installation surface such as

ceiling or wall.

3

Make holes in the installation surface according to the installation positioning

template.

4

Insert the three expansion bolts into the holes.

5

Position the IP camera base over the holes

6

Use the screws from the accessories bag to secure the IP camera firmly.

9

Step Description

 If you run the cable from the top of the installation surface, make an exit hole

on the installation surface according to the installation positioning template.

 If you run the cable from the side of the cable channel, it must go through the

U-shaped channel on the dome support. Take out the cable from the side of the

exit hole located on the support.

7

Adjust the device installation support to the proper position and then run the cable

through the exit hole located on the installation surface.

8

Align the TOP mark on the device installation support with that of the installation

template.

9

Align the three screw holes in the device support with the three plastic expansion

bolt holes in the installation template.

10

Firmly affix the three self-tapping screws to the three plastic expansion bolts.

11

Secure the dome body to the installation surface.

12

Hold both sides of the base of the rotation bracket, rotate horizontally along the

axis and adjust the lens in the horizontal direction to the designated position.

13

Hold the LED cover and rotate it vertically while adjusting the lens in the vertical

direction to the designated position.

If too tight to adjust, first loosen the fixed screws on both sides of the bracket (do not

remove the fixed screws), then adjust the lens and tighten again the fixed screws.

14

While holding the LED cover, rotate it along the axis and adjust the lens image to

the correct surveillance position.

Range of lens:

 vertical (0°～+64°)

 horizontal (0°～+355°)

 image rotation direction (0°～+355°)

NOTE – When rotation is at 64° in the vertical direction, please pay attention to the

image rotation direction in order to prevent blockage of the IR light by the outer

cover, as this can negatively influence the IR effect.

10

Powering-up the IP Camera

1. Connect power to the Power port on the IP camera.

2. Connect power to an electrical outlet. When the IP camera boots up, the

GREEN power indicator light flashes.

Connecting the IP Camera to the Network

The IP camera supports several network connection options including LAN and

Wireless.

Connecting to a LAN Network

Connecting the IP camera to a network using the LAN (Local Area Network)

enables easy connection and setup with compatible APs (Access Points), e.g.

gateway or router.

1. Connect the incoming network cable to the Network port on the IP camera.

2. The GREEN network indicator lights to indicate that your IP camera is now

connected to the network. Continue as explained in Defining IP Camera

Settings.

Connecting to a Wireless Network using WPS

Connecting the IP camera to a wireless network using WPS (Wi-Fi Protected

Setup) requires that the router supports WPS functionality.

NOTE – Some routers have a virtual button on their management software.

(Refer to the router’s documentation for details about using its WPS functions).

1. Once the power cord is connected, wait for slow flashing GREEN network

indicator.

2. Momentarily press the WPS button on the IP camera and hold down the

WPS button on the router for 2 seconds. The GREEN network indicator light

indicates that your IP camera is now connected to the network. Continue as

explained in Defining IP Camera Settings.

11

Connecting to a Wireless Network using the RISCO Cloud

Connecting the IP camera to a wireless network using the RISCO Cloud (RISCO

Application Server) requires that you first connect the IP camera to the router via

the LAN and then, from the RISCO Cloud Installer Application, define the IP

camera settings and establish a wireless connection. Once a wireless connection

has been established the IP camera can then be disconnected from the router and

installed/mounted.

1. Connect the incoming network cable to the Network port on the IP camera.

2. The GREEN network indicator lights to indicate that your IP camera is now

connected to the network. Continue as explained in Defining IP Camera

Settings.

NOTE – Before disconnecting you must configure the wireless network through

the RISCO Cloud.

3. Once a wireless connection has been established, you may disconnect the IP

Camera from the router and install/mount it anywhere within the monitored

area.

12

IP Cameras and the RISCO Cloud Installer Application

The RISCO Cloud Installer Application provides an interface to your control

panel from a local or remote PC via the Web. This enables you to add IP cameras

and define camera and event alarm trigger settings.

IMPORTANT – A control panel must first be defined in RISCO Cloud in order

to accept IP cameras and define camera settings (Refer to the RISCO Cloud

Installer Application Manual)

Defining IP Camera Settings

Once you have connected the IP camera to the network (refer to, Connecting the

IP Camera to the Network) you can define the camera settings.

To define IP camera settings:

1. Log into the Installer Administration application using the Web page address

supplied by your service provider and enter your user name and password.

NOTE – It is recommended to use Google Chrome or Mozilla Firefox to log into

the Installer Administration application.

2. Select the Control Panels List link. The Control Panels List page is displayed.

Figure 5 Control Panels List Page

3. From the Control Panels List page, select the Control Panel you wish to view.

The Control Panels Update page is displayed.

13

Figure 6 Control Panel Update Page

4. Click the Network Cameras link in the left-hand column; the IP Camera List

page is displayed.

Figure 7 IP Cameras List

5. Click Add Camera; the Add Camera dialog box is displayed.

6. Select the RISCO P2P Camera type.

Figure 8 Add Camera

7. Define the following fields in the Add Camera dialog box.

Field Description

Label

Enter a name for the camera

Partitions

Select the partition(s) from the list of defined partitions

Type

Choose the RISCO P2P Camera type (for ONVIF or Generic camera type

settin

g

s, refer to the RISCO Cloud Installer A

pp

lication Manual)

MAC

Address

Enter the MAC address into this field. The MAC address (media access

control address) is the unique identifier assigned to the IP camera for

communications on the physical network.

NOTE: The MAC address is case sensitive and should be entered exactly as

it is shown on the box or on the back cover of the IP camera, e.g.

AA:BB:CC:DD:EE:FF

14

8. Click Add; the following message is displayed.

Figure 9 Waiting for camera to connect message

If the “Connect to WiFi” message is displayed, go straight to step 8.

Figure 10 Connect to WiFi message

9. Select one of the following options:

Connect to Wi-Fi – to establish a wireless network connection (go to step 9 to

connect the IP camera to the wireless network).

Not Now – to maintain IP Camera connection using a LAN network

connection (skip the wireless network connection steps 10, 11 and 12 and

connect the IP camera to the LAN network).

10. If you selected the “Connect to Wi-Fi” option, a list of available wireless

networks is displayed.

Figure 11 List of available wireless networks

11. Select a wireless network from the available list and click Connect.

15

NOTE – If your network is password protected, a password must be entered into

the displayed password screen.

Figure 12 AP Network Password

12. Click Connect to establish the wireless connection (Refer to Connecting to a

Wireless Network using the RISCO Cloud); the following success message is

displayed.

Figure 13 Operation Completed

13. Once the “camera is ready for use” message is displayed, click Close. The

defined IP camera is displayed in the IP Cameras page.

NOTE – Once a wireless connection has been established, don’t forget to

disconnect the IP camera Ethernet cable from the router.

Figure 14 IP Camera List

16

NOTE – You also have the option to edit or delete the selected IP camera.

Click the FW Action button below to check if the firmware is up-to-date.

Figure 15 Firmware Update

The newer Firmware version will be displayed in the screen that opens, if applicable.

Figure 16 Newer Firmware Version

Defining Camera Trigger Settings

Any event from the following list can be defined to trigger an alarm.

Partition Events

Fire Alarm Panic Alarm Medical Alarm Alarm

Full Arm Part Arm Disarmed Duress

Tamper 24 HR-X Alarm Water Alarm Gas Alarm

Environ. Alarm No Motion Alarm Exit Alarm Low Temperature

Detector Events

Alarm Zone Bypassed Zone Un-bypassed Zone Tamper

17

To define camera trigger settings:

1. From the Control Panel Cameras page, click the Triggers tab, the Camera

Triggers List page is displayed.

Figure 17 Camera Triggers List

2. Click Add Trigger; the Add Triggers dialog box appears.

Figure 18 Add Trigger

3. Define the following fields in the Add Trigger dialog box:

Field Description Event Type

Label

Enter a name for the camera trigger Partition and Detector events

Camera

Choose a camera from the list Partition and Detector events

Event Type

Choose an event type from the list Partition and Detector events

Event

Choose the event from the list, e.g.

alarm, duress, etc.

Partition and Detector events

18

Additional fields are displayed in the Add Trigger dialog box according to the

event type that you selected (see examples below for Partition and Detector event

types).

Figure 19 Add Partition Event Trigger Figure 20 Add Detector Event Trigger

4. Define the following fields in the Add Trigger dialog box according to the

event type that you selected.

Field Description Event Type

Partition(s)

Select the partition(s) from the list.

NOTE – Only partitions associated with

the camera are displayed.

Partition events only

Detectors

Select the detector from the list Detector events only

5. Define the following image (still) and clip (video) definitions:

Field Description

Images

(still)

Pre-event starting time (sec) – time, before the actual event occurred, to

start displaying still images.

Number of images – number of still images to display.

Interval between images (sec) – time required between each still image.

Clips

(video)

Pre-event starting time (sec) – time, before the actual event occurred, to

start displaying video clip.

Duration (sec) – total duration of the video clip

NOTE – These fields are currently locked and the default parameters

cannot be changed.

NOTE: To be able to record video clips, make sure to insert an SD Card and then

power down/up the camera.

La page charge ...

Risco VUpoint RVCM32W Guide d'installation

Risco VUpoint RVCM32W Guide d'installation

dans d''autres langues

Documents connexes

Autres documents