Kenwood DRV-410 Le manuel du propriétaire

DRV-410

GPS Integrated Dashboard Camera

INSTRUCTION MANUAL

Camera de tableau de bord avec GPS integre

MODE D’EMPLOI

Camara de salpicadero con GPS integrado

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model DRV-410

Serial number

US Residents Only

Register Online

Register your Kenwood product at www.Kenwoodusa.com

3

CONTENTS

•

The screen images and operation examples in this document were created for

explaining the operating procedures. There may be screen images that dier from the

actual screens or examples of operations not actually performed.

•

Unless otherwise specied, microSDHC cards are referred to as SD cards in this

document.

•

The latest instruction manual, rmware update information, etc. are available at the JVC

KENWOOD website. Please visit the following website.

http://www.kenwood.com/cs/ce/

Disclaimer

•

Please note that JVC KENWOOD shall not be responsible for any damages suered by the customer or

a third party as a result of incorrectly using this product, a failure during use of this product, or other

trouble, or due to the use of this product, unless such liability is acknowledged by law.

Copyrights

•

Recorded video, image, and audio content cannot be used for other than personal enjoyment

without the consent of the copyright holder as specied in the Copyright Act.

•

Please note that the recording of an event such as a show, performance, or exhibition may be

restricted even when doing so for personal enjoyment.

Precautions for Use ................................................................................................................... 7

How to Install ............................................................................................................................. 8

How to Wire .............................................................................................................................. 10

Names and Functions of Parts ................................................................................................ 11

Before Using the Driving Support Function .......................................................................... 12

Basic Operations ...................................................................................................................... 13

Recording ................................................................................................................................. 16

Playback ................................................................................................................................... 17

Protecting or Deleting Files .................................................................................................... 18

Various Settings ....................................................................................................................... 19

Using the PC Application ........................................................................................................ 24

Troubleshooting ...................................................................................................................... 28

Appendix .................................................................................................................................. 31

Specifications ........................................................................................................................... 34

English

4

Precautions and notices

Warning! Do not operate the device while driving. Using this product does not change the

requirement for a driver to take full responsibility for his or her behavior. This responsibility includes

observing all trac rules and regulations in order to avoid accidents, personal injury or property

damage.

•

For your own safety, do not operate the controls of the product while driving.

•

A window mount is needed when using the recorder in a car. Make sure that you place the

recorder in an appropriate place, so as not to obstruct the driver’s view or deployment of airbags.

•

Make sure that no object is blocking the camera lens and no reective material is placed near the

lens. Please keep the lens clean.

•

If the car’s windscreen is tinted with a coating, it may impact the recording quality.

•

Connect the charger to a proper power source. The voltage requirements are found on the

product case and/or packaging.

•

Do not use the charger if the cord becomes damaged.

•

Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is

damaged or exposed to excess moisture.

5

Caring for your device

Taking good care of your device will ensure trouble-free operation and reduce the risk of damage.

•

Keep your device away from excessive moisture and extreme temperatures.

•

Avoid exposing your device to direct sunlight or strong ultraviolet light for extended periods of

time.

•

Do not place anything on top of your device or drop objects on your device.

•

Do not drop your device or subject it to severe shock.

•

Do not subject your device to sudden and severe temperature changes. This could cause

moisture condensation inside the unit, which could damage your device. In the event of moisture

condensation, allow the device to dry out completely before use.

•

The screen surface can easily be scratched. Avoid touching it with sharp objects. Nonadhesive

generic screen protectors designed specically for use on portable devices with LCD panels may

be used to help protect the screen from minor scratches.

•

Never clean your device with it powered on. Use a soft, lint-free cloth to wipe the screen and the

exterior of your device.

•

Do not use paper towels to clean the screen.

•

Never attempt to disassemble, repair or make any modications to your device.

Disassembly, modication or any attempt at repair could cause damage to your device and even

bodily injury or property damage and will void any warranty.

•

Do not store or carry ammable liquids, gases or explosive materials in the same compartment as

your device, its parts or accessories.

•

To discourage theft, do not leave the device and accessories in plain view in an unattended

vehicle.

•

Overheating may damage the device.

6

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this

equipment may cause harmful interference unless the modications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized

change or modication is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment may cause harmful interference to radio communications, if it is not installed and

used in accordance with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

7

Precautions for Use

Precautions for Installation

•

Install the device in a position where it will

not block the front view of the driver (position

where hidden by the rear-view mirror).

•

Install the device so that it is within the wiping

range of the wiper.

•

Install the device in a position where it will not

interfere with the movement of the rear-view

mirror.

•

Take care not to install the device over the

vehicle inspection sticker or other sticker.

•

Take care not to install the device where it will

interfere with driving or airbag operation.

•

When installing the device in a vehicle

equipped with a driving support system, check

the instruction manual of the vehicle and then

select an installation location that will not

interfere with the driving support system.

•

If the device is installed incorrectly, event

recording or parking recording may not work

correctly. Refer to "How to Install" for the

loosening of xing knob, installation orientation,

installation angle, and other information and

then install the device correctly.

(

Á

P. 8)

•

Do not install the device near a digital terrestrial

television antenna or an electrical component.

Doing so may reduce television receiver

sensitivity or cause ickering and noise.

•

Use a commercially available cleaning cloth

or the like to wipe off all dirt and grease on

the mounting surface and then x the mount

base in place. If the device is re-affixed or

mounted using, for example, general-purpose

double-sided tape, the adhesion strength may

weaken and cause the device to fall.

•

After mounting the device, leave it for 24

hours before use to enable the mounting

strength of the mount bracket to improve.

Failing to do so may result in the adhesion of

the mount bracket becoming weak and the

device falling.

•

Fix the cord in place with tape or the like so

that it does not interfere with driving.

Precautions for Use

•

Do not block the camera lens, get dirt on it, or

place a reective object near it.

•

When LED trac lights are recorded, video in

which they appear to be ickering or ashing

may be recorded. JVC KENWOOD assumes no

responsibility with regard to the distinguishing

or recording of trac lights.

•

If coating is used on the windshield of the

vehicle, recording quality may be aected.

•

There is no guarantee that the device can

record video in all conditions.

Cleaning the Device

•

When the device is dirty, wipe it with a dry

silicone cloth or other soft cloth. If the device

is very dirty, remove the dirt with a cloth

with neutral cleaner on it and then wipe off

the cleaner. Wiping the device with a hard

cloth or using using a volatile substance such

as thinner or alcohol may cause scratches,

deformation, deterioration, or other damage.

•

When the lens is dirty, gently wipe it with a soft

cloth dampened with water. Rubbing the lens

strongly with a dry cloth may cause scratches.

If You Notice a Problem with the

Device

If you notice a problem with the device, first

refer to "Troubleshooting" (

Á

P.28) and check

whether there is a way to resolve the problem.

If you are unable to find a way to resolve the

problem, press the [MENU/OK] button on

the device for at least 25 seconds to reset the

device. When the power turns o after resetting

the device, press the [MENU/OK] button for at

least 1 second to turn on the power. (

Á

P.11)

If the device does not return to normal after the

reset, turn o the power of the device and then

contact your dealer or nearest JVC KENWOOD

service center.

8

How to Install

Installation Procedure

Check that the vehicle is parked on a level

surface.

1.

Attach the device to the mount

bracket. (accessory)

Insert the mount bracket into the bracket

attachment part of the device and attach it to

the device.

Camera lens side

Mount bracket

2.

Determine where to mount the

device.

Determine the mounting position in reference

to "Recommended installation position."

3.

Clean the mounting surface and then

ax the device to the windshield.

Use a commercially available cleaning cloth or

the like to wipe off all dirt and grease on the

mounting surface. Peel o the release paper of

the double-sided tape on the mount bracket

and push the bracket against the windscreen

to ax it in place. Leave the device for 24 hours

before use to enable the mounting strength of

the mount bracket to improve.

Release paper

4.

Perform the cord wiring work.

Refer to "How to Wire" and then perform the

wiring work. (

Á

P.10)

5.

Adjust the installation angle of the

device and then x the device in place.

Turn the angle adjustment knob clockwise before

adjustment. When adjusting the installation angle,

check that the camera eld of view is parallel to a level

ground surface and that the ratio of the sky and ground

are the same. After adjusting the installation angle, turn

the angle adjustment knob of the adjustment bracket

counterclockwise to x the device in place.

Adjustment example

Angle

adjustment knob

Windshield

Rear-view mirror

•

If you will use the driving support

function, you need to make the

adjustments described in "Adjusting the

Settings to Match the Vehicle." (

Á

P.12)

•

Make the adjustments described in

"Adjusting the Settings to Match the Vehicle"

in a location with a level surface and a sight

distance of about 200 m. (

Á

P.12)

9

Recommended installation position

•

Install the device in a position where it will not block the front view of the driver (position where hidden

by the rear-view mirror).

•

Install the device so that it is within the wiping range of the wiper.

•

Mounting the device to the center of the windshield behind the rear-view mirror will facilitate optimal

video recording.

CAUTION

When passing the power cord through the front pillar or another part, observe the following points when

performing the wiring work.

•

Wire the power cord farther forward or farther rearward than the airbag so that it does not interfere with the airbag.

•

In the case of a vehicle in which the front pillar cover is xed in place with special clips or the like, the

clips may need to be replaced after you remove the front pillar cover. For how to remove the front pillar

cover, the availability of replacement parts, and other information, contact the vehicle dealer.

•

Fix the power cord in place with commercially available soft tape or the like so that it does not interfere with driving.

Windshield

Double-

sided tape

Inside

vehicle

Outside

vehicle

Front pillar cover

Clip

Airbag

Front pillar

Power cord

Soft tape*

* Fix the power cord in place with commercially available soft

tape or the like.

Rear-view

mirror

Power cord

Ceramic part

10

How to Wire

Before performing the connection work, rst check that the engine key

is removed and then be sure to disconnect the negative terminal of the

battery to prevent a short accident.

CAUTION

Power cord for Dashboard Camera (accessory)

Connecting the cigarette lighter plug cord (accessory)

Cord length (4 m)

Connect the drive recorder and power cord of the cigarette lighter plug cord.

Drive recorder

Connect the cigarette lighter plug to the cigarette lighter socket.

When disconnecting the power cord, disconnect

it while pressing the hook of the connector.

Ground cord (Black)

Connect to a metal part of the vehicle (part of the chassis with an electrical

connection to the negative side of the power supply).

Ignition key switch

Fuse

Battery

Main fuse

GND

Accessory cord (Red)

Connect to a power supply that can

be turned on and o with the switch.

Battery cord (Yellow)

Connect to a power supply with a voltage always applied

regardless of whether or not the engine key is on or o at

a point after the power has passed through the main fuse.

Accessory power supply

Fuse (2 A)

Dashboard Camera

Connect the Dashboard Camera and power cord.

Cord length (3.5 m)

ACC

BAT T

11

Names and Functions of Parts

1

Bracket attachment part

Attach the supplied mount bracket.

2

Camera lens

3

Speaker

Outputs voice guidance, warning sounds, and

le playback audio.

4

Power cord connector terminal

Connect the supplied cigarette lighter plug

cord or the Dashboard Camera power cable.

5

J

button

•

Press this button during playback to play the

previous le.

•

Hold down this button during playback to

rewind, and hold it down while playback is

paused to play slowly in the reverse direction.

Release this button during rewinding to play, and

release it during reverse slow playback to pause.

•

Press this button during menu display to

return to the previous item.

6

MENU/OK button

•

Hold down this button to turn on or o the

power of the device.

•

Press this button to display the MENU screen.

•

This button functions as the OK button

during menu display.

•

Hold down this button for at least 25

seconds to reset the device.

7

Microphone

Records audio.

1

8

2

9

3

!

0

@

7

5

4

6

8

K

button

•

Press this button during continuous

recording to take a photo.

•

Press this button during playback to play the

next le.

•

Hold down this button during playback

to fast-forward, and hold it down while

playback is paused to play slowly in the

forward direction. Release this button during

fast-forwarding to play, and release it during

forward slow playback to pause.

•

Press this button during menu display to go

to the next item.

9

Monitor screen

0

SD card slot

Insert an SD card for recording.

!

Indicator

Lights when the power of the device turns on.

@

button

•

Press this button during continuous

recording to start manual recording.

•

Each press of this button during playback

switches between the paused and playback

states.

•

Press and hold this button during playback

or menu setting to return to continuous

recording.

•

This button functions as the cancel, back, or

exit button during menu display.

12

Adjusting the Settings to Match the Vehicle

Before using the driving support function, set

the mounting height of the device from the road

surface and adjust the horizon and bonnet front

edge position settings to match the vehicle.

1.

Press the [MENU/OK] button.

MENU appears.

2.

Use the [

J

]/[K] buttons to select

<Driving support settings> and then

press the [MENU/OK] button.

2

1

3.

Use the [

J

]/[K] buttons to select

<Mounting height settings> and

then press the [MENU/OK] button.

2

1

4.

Use the [

J

]/[K] buttons to select the

mounting height from the road surface

and then press the [MENU/OK] button.

2

1

5.

Use the [

J

]/[K] buttons to select

<Detection range settings> and then

press the [MENU/OK] button.

2

1

6.

Press the [MENU/OK] button, use the [

J

]/[K]

buttons to align the guide line with the horizon,

and then press the [MENU/OK] button.

Adjust as shown in the gure.

1

2

3

7.

Press the [MENU/OK] button, use the

[

J

]/[K] buttons to align the guide

line with the bonnet front edge, and

then press the [MENU/OK] button.

Adjust as shown in the gure.

1

2

3

8.

Hold down the [ ] button to

end the procedure.

•

For the mounting height setting, set the

nearest height among the setting options.

•

In the case of a vehicle for which the bonnet

front edge cannot be seen, lower the guide line

to the lowest position at which the center of the

road surface is not hidden by the body or a part

of the vehicle and then set the setting.

•

The driving support function is set to

"OFF" by default (

Á

P.21).

Before Using the Driving Support Function

13

Inserting and Removing an SD Card

Turn o the power of the device and then insert

an SD card into the SD card slot until you hear

a clicking sound. Be careful with regard to the

orientation of the card.

To remove the SD card, turn o the power of the

device and then press the SD card so that it pops

up and remove the SD card by pulling it out.

•

Be sure to format an SD card with the

device.

•

When an SD card is formatted, all files

including protected les are deleted.

Turing the Power On/Off

Turning on the accessories power (ACC) switch

or starting the engine of the vehicle turns on

the power of the device and starts continuous

recording. When the device is connected using the

power code (

Á

P.10), turning off the accessories

power (ACC) turns o the power of the device and

switches to parking recording mode.

To Turn the Power On/Off Manually

When the accessories power (ACC) is on, the power

of the device can be turned on or o manually.

•

Hold down the [MENU/OK] button for at least 3

seconds while the device is on to turn o the power.

•

Hold down the [MENU/OK] button for at least 1

second while the device is o to turn on the power.

•

When the power has been turned off

manually, power is consumed because the

device is in standby.

•

There are vehicle models such as some

imported vehicles for which the power

to the cigarette lighter is not cut o even

when the engine is turned o. To protect

the battery, remove the cigarette lighter

plug when you get out of the vehicle.

Formatting an SD Card

Before using an SD card, rst format (initialize) it

with the device.

1.

Insert the SD card into the SD card slot.

2.

Press the [MENU/OK] button.

MENU appears.

3.

Use the [

J

]/[K] buttons to select

<Format SD card> and then press the

[MENU/OK] button.

2

1

4.

Use the [

J

]/[K] buttons to select

<OK> and then press the [MENU/OK]

button.

2

1

5.

Press the [MENU/OK] button to end

the procedure.

Basic Operations

14

Recording Modes

The device has four recording modes. Turning on the power of the device starts continuous

recording. The recorded video is recorded as les to the SD card. The recording les are sorted into a

separate folder for each recording mode.

Continuous recordings

Turning on the power of the device starts continuous recording. In continuous recording mode,

les are deleted in order from the oldest to record when there is no recording area remaining.

Continuous

recording

Elapsed time

→

•

The recording data is saved to the continuous recordings folder.

•

The recording time of one le can be set in "Continuous recording le length" (

Á

P.20).

Manual recording

Pressing the [ ] button on the device during continuous recording starts manual

recording. The recording time of manual recording is the 10 seconds before manual recording plus

the time set in "Manual recording time" (

Á

P.20). If you wish to extend the recording time, press

the [ ] button again. When manual recording ends, the mode returns to continuous

recording.

Elapsed time

→

Continuous

recording

Records 10 seconds before

manual recording

Manual recording

(If the button is pressed during manual recording, the recording time is extended

from that point by the amount of recording time set for manual recording.)

Manual recording (set time)

•

The recording data is saved to the manual recordings folder.

•

The recording time of one le is a maximum of one minute. If the recording time exceeds one minute,

the le is split to record.

•

When 10 les will be exceeded, manual recording cannot be performed (when 8 GB SD card). When

"Overwrite (manual)" is set to "ON," les are deleted in order from the oldest to record (

Á

P.20). Back

up the recording data you wish to keep to a PC or other device if necessary.

Basic Operations

15

Event recording

The detection of a sudden collision, unexpected collision, or other event during continuous

recording starts event recording. The recording time of event recording is the 10 seconds before

collision detection plus the time set in "Event recording time" (

Á

P.20). When event recording ends,

the mode returns to continuous recording.

•

The recording data is saved to the event recordings folder.

•

The recording time of one le is a maximum of one minute. If the recording time exceeds one minute,

the le is split to record.

•

If a collision is detected during event recording, event recording is extended.

•

When ve les will be exceeded, event recording cannot be performed (when 8 GB SD card). When

"Overwrite (event)" is set to "ON," les are deleted in order from the oldest to record (

Á

P.20). Back

up the recording data you wish to keep to a PC or other device if necessary.

Parking recording

Turning o the accessories power (ACC) turns o the power of the device and switches to parking

recording mode to perform vehicle collision monitoring. If the vehicle is subjected to a collision, the

power of the device turns on and parking recording starts. When parking recording ends, vehicle

collision monitoring resumes.

Parking recording

Collision detected

Collision

monitoring

Parking recording (set time)

Elapsed time

→

•

Parking recording mode is available only when the device is connected using the power code (

Á

P.10)

•

The recording data is saved to the parking recordings folder.

•

Parking recording starts a few seconds after the vehicle is subjected to a collision.

•

The monitor screen is not displayed during parking recording.

•

When 20 files will be exceeded, parking recording cannot be performed (when 8 GB SD card).

Delete any unnecessary data or back up the recording data you wish to keep to a PC or other device

if necessary. You can conrm whether there is an excess number of les with the "

8 Number of

les exceeded" indicator on the recording screen (

Á

P.16).

•

If parking recording is performed, a notication on the screen informs you that parking recording

has been performed when the power turns on.

•

Parking recording cannot be performed when "Recording time" is set to "OFF" (

Á

P.20).

•

Parking recording may sometimes be performed as result of detecting vibration when a door is closed.

Elapsed time

→

Continuous

recording

Collision detected

Records 10 seconds before

collision detection

Event recording (set time)

Event recording

16

Recording at Any Location (Manual

Recording)

Pressing the

[

]

button on the device

during continuous recording allows you to

record manually whenever you wish.

1.

Press the [ ] button.

Manual recording starts and then the mode

returns to continuous recording after the time

set for the recording time of manual recording

elapses.

•

If you wish to extend the recording time,

press the [ ] button again.

•

The recording time of manual recording

is the 10 seconds before manual

recording plus the time set in "Manual

recording time." (

Á

P.20)

•

Recording cannot be performed during

folder or le selection, playback, deletion,

and setting.

Recording

Taking a Photo

Pressing the [K] button on the device during continuous

recording allows you to take a photo whenever you wish.

1.

Press the [K] button.

•

If you wish to take another photo, press

the [K] button again.

•

A photo cannot be taken when the device

is not recording such as during playback

or when conguring menu settings.

Recording screen indicators

1

4 5 6 7 9

2 3

8

1

Recording mode

2

Time

3

GPS reception state

4

Resolution (3M: 2304x1296, FHD:

1920x1080, or HD: 1280x720)

5

Audio recording

6

HDR recording

7

Remaining manual recording or event

recording time

8

Number of les exceeded (manual recording,

event recording, parking recording, or photos)

9

Photo taking

Recording at Any Location (Forcibly

Recording)

Forcibly start recording even during playback or

menu display.

1.

Hold down the [ ] button.

Playback or menu display stops and continuous

recording resumes.

17

Playing Files

Select a file such as a recording file or photo

and start playback.

1.

Press the [MENU/OK] button.

MENU appears.

2.

Use the [

J

]/[K] buttons to select

<Playback> and then press the

[MENU/OK] button.

2

1

3.

Use the [

J

]/[K] buttons to select

the folder you wish to play and then

press the [MENU/OK] button.

The video for the most recent file in the

selected folder is displayed.

2

1

Continuous

recordings

There are continuous recording

les.

Manual recordings There are manual recording les.

Event recordings

There are event recording les.

Parking recordings There are parking recording les.

Still images

There are still image les.

4.

Use the [

J

]/[K] buttons to select the

le you wish to play and then press

the [MENU/OK] button and press the

[

] button.

Playback of the selected le begins.

2

1

Pressing the

[

J

]

or

[K]

button during

playback plays the previous or next le or photo.

To return to continuous recording

Hold down the [ ] button.

•

Files are listed in their recording or

capture order.

•

Recording is stopped while selecting a

folder or file and during playback. Also,

manual recording using the [

]

button does not work.

Playback screen indicators

1

65

4

2 3

1

Recording le playback state or photo

le indication

2

Play time

3

Play position

4

Recording le name, date, and time

5

File protection

6

Number of le playing/total number of les

Playback

18

Operation with the Playback

Menu

Protect or delete files such as event recording

les or photos. You can also delete all of the les

in a folder.

1.

Select a le or photo to play.

2.

Press the [MENU/OK] button, use the

[

J

]/[K] buttons to select an item, and

press the [MENU/OK] button.

2

1

Return Returns to folder selection.

Delete le Deletes a le that is not protected.

Delete folder

Deletes all les in the folder that are

not protected.

Protect le

Protects the le so that it will remain

even if an attempt to overwrite or

delete it is made.

Remove le

protection

Removes le protection.

3.

Use the [

J

]/[K] buttons to select

<OK> and then press the [MENU/OK]

button.

2

1

4.

Press the [MENU/OK] button to end

the procedure.

•

Continuous recording files cannot be

protected.

•

To delete a protected file, remove file

protection.

•

When an SD card is formatted, all files

including protected les are deleted.

Protecting or Deleting Files

19

Various Settings

Operation with MENU

Perform operations such as playback and

conguring video recording settings on the

MENU screen.

1.

Press the [MENU/OK] button.

MENU appears.

2.

Use the [

J

]/[K] buttons to select an

item and then press the [MENU/OK]

button.

2

1

Repeat the same operation according to the

selected item.

3.

Hold down the [ ] button to

end the procedure.

•

Except for the recording described in

"Recording at Any Location (Forcibly

Recording)," recording is not possible

while the menu is displayed. (

Á

P.16)

The MENU screen of step 2 changes in the

following order.

Playback

Parking recording settings

Video recording settings

Driving support settings

System settings

Format SD card

Update system

20

Various Settings

* Factory default settings

MENU

Playback

Continuous recordings

Select the desired folder from the list screen and play a le. (

Á

P.17)

Files can also be protected or deleted during playback. (

Á

P.18)

Manual recordings

Event recordings

Parking recordings

Still images

Parking recording settings

Recording time OFF/10 sec*/20 sec/30 sec

Set the recording time for parking recording after collision detection.

Overwrite ON*/OFF

Set whether or not to overwrite old files when the maximum number of

recording les will be exceeded.

Sensitivity settings

1(Low)/2/3(Mid)*/4/5(High)

Set the sensitivity for detecting a vehicle collision while parked.

1: Detects large collisions, 3: Standard, 5: Detects small collisions

Video recording settings

Audio recording ON*/OFF

Set whether or not to record audio with the microphone during recording.

Continuous recording file

length

1 min*/2 min/3 min

Set the recording time for continuous recording. The recording is divided each

time the recording time elapses.

Manual recording time 15 sec*/30 sec/1 min

Set the recording time for manual recording. The recording time for before

manual recording is set to 10 seconds.

Event recording time 15 sec*/30 sec/1 min

Set the recording time for after collision detection. The recording time for

before vehicle collision detection is set to 10 seconds.

Overwrite (manual) ON/OFF*

Set whether or not to overwrite old files when the maximum number of

recording les will be exceeded.

Overwrite (event) ON/OFF*

Set whether or not to overwrite old files when the maximum number of

recording les will be exceeded.

Resolution

3M (2304x1296)/1920x1080*/1280x720

Set the resolution for recording.

HDR recording ON*/OFF

Setting this to ON records subjects by reducing overexposure and loss of dark detail even when

capturing scenes with high light-dark contrast. HDR cannot be set to ON when the resolution is 3M.

Sensitivity settings

1(Low)/2/3(Mid)*/4/5(High)

Set the sensitivity for detecting a vehicle collision.

1: Detects large collisions, 3: Standard, 5: Detects small collisions

La page charge ...

Kenwood DRV-410 Le manuel du propriétaire

Kenwood DRV-410 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents