KitchenAid KBPU182VSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBPU182VSS00

Taper: Le manuel du propriétaire

Ce manuel convient également à

POWER KBPU182VSS

I_itchen_kid ®

OUTDOOR BUILT-IN POWER TMBURNER

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, call for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.KitchenAid.ca

BRULEUR HAUTE PUISSANCE ENCASTRE

POWER TMPOUR USAGE EXTERIEUR

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site Web a...

www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 4

iMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

_, conserver pour consultation par I'inspecteur local des installations _lectriques.

InstaHateur : Remettre les instructions d'installation au propri_taire.

Propri6taire : Conserver les instructions d'installation pour r_f_rence ult_rieure.

Model/Modele KBPU182VSS

W10243318A

OUTDOOR BUILT-IN POWER TMBURNER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

_, DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

,_ WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

m If using a ball valve, it shall be a T-handle type.

m A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: This Power TM burner is manufactured for outdoor use only. For Power TMburners that are to be used at elevations

above 2000 ft (609.6 m) orifice conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to

comply with the minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate can be found

on the right-hand side panel.

Copies of the standards listed may be obtained from:

National Fire Protection Association CSA International

One Batterymarch Park 8501 East Pleasant Valley Rd.

Quincy, Massachusetts 02269 Cleveland, Ohio 44131-5575

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

m Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

m Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

m The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

m This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

m Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

m Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

[] Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

[] Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

[] Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

[] Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

SAVE THESE

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

"Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

[] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

iNSTRUCTiONS

TABLEOF CONTENTS

OUTDOOR BUILT-IN POWER TM BURNER SAFETY ................... 2

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Product Dimensions .................................................................... 5

Cabinet Dimensions ..................................................................... 6

Electrical Requirements ............................................................... 9

Gas Supply Requirements ........................................................... 9

Gas Connection Requirements .................................................. 10

INSTALLATION INSTRUCTIONS ................................................ 11

Built-in Outdoor Power TM Burner Installation ............................ 11

Install Tank Tray for 20 Ib LP Gas Fuel Tank ............................. 11

GAS CONVERSIONS .................................................................... 15

Tools and Parts for Gas Conversion .......................................... 15

Conversion to a Local LP Gas Supply ....................................... 15

Conversion from LP Gas to Natural Gas ................................... 16

Check and Adjust the Burners ................................................... 18

USING YOUR OUTDOOR POWER TM BURNER ......................... 19

PowerTM Burner Use .................................................................. 19

LightingYour PowerTM Burner ................................................... 20

OUTDOOR POWER TM BURNER CARE ...................................... 21

General Cleaning ........................................................................ 21

TROUBLESHOOTING .................................................................. 22

ASSISTANCE OR SERVICE ......................................................... 22

In the U.S.A................................................................................ 22

Accessories ................................................................................ 22

In Canada ................................................................................... 22

WAR RANTY .................................................................................. 23

TABLEDES MATIERES

SI_CURITI_ DU BRULEUR HAUTE PUISSANCE ENCASTRI_

POUR USAGE EXTI_RIEUR POWER TM ....................................... 25

EXIGENCES D'INSTALLATION ................................................... 27

Outillage et pieces ...................................................................... 27

Exigences d'emplacement ......................................................... 27

Dimensions du produit ............................................................... 27

Dimensions du placard .............................................................. 27

Specifications electriques .......................................................... 30

Specifications de I'alimentation en gaz ..................................... 31

Exigences concernant le raccordement au gaz ........................ 32

INSTRUCTIONS D'INSTALLATION ............................................. 34

Installation du brQleur haute puissance d'exterieur

encastre Power TM ....................................................................... 34

Installation du chariot de bouteille de gaz propane

de 20 Ib....................................................................................... 34

CONVERSIONS DE GAZ .............................................................. 38

Outillage et pieces ...................................................................... 38

Conversion au gaz propane local .............................................. 38

Conversion du gaz propane au gaz naturel ............................... 39

Contr61e et reglage des brQleurs................................................ 41

UTILISATION DU BRULEUR HAUTE PUISSANCE POWER TM

D'EXTI_RIEUR ............................................................................... 42

Utilisation du brQleur haute puissance Power TM ........................ 42

Allumage du brQleur haute puissance Power TM ........................ 43

ENTRETIEN DU BRULEUR HAUTE PUISSANCE POWER TM

D'EXTI_RIEUR ............................................................................. 44

Nettoyage general ...................................................................... 44

DI_PANNAGE ................................................................................. 45

ASSISTANCE OU SERVICE ......................................................... 46

Accessoires ................................................................................ 46

GARANTIE .................................................................................... 47

INSTALLATION REQUIREMENTS

_?' i_: _ _._1:_

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Tape measure • Wrench or pliers

• Small, flat-blade screwdriver • Pipe wrench

• Flat-blade screwdriver • Scissors or cutting pliers

• #2 and #3 Phillips screwdriver (to remove tiedowns)

• Level • Noncorrosive leak-

detection solution

Parts Supplied

Gas pressure regulator/hose assembly set for 11" WCP LP

gas (attached to manifold)

• 1 single-prong plug/2,085 mAmp transformer assembly

• Convertible regulator set for 4" WCP Natural gas

• Orifices for Natural gas conversion

• LP gas fuel tank tray

Parts Needed

• 20 Ib LP gas fuel tank - approximately 18" (45.7 cm) height

and 12" (30.5 cm) diameter

[,,:}ca ::(_s Reqs,:: te_sle its

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for built-in outdoor

Power TM burners:

• A minimum of 24" (58 cm) must be maintained between the

sides and back and any combustible construction.

• A zero clearance may be maintained below the cooking

surface and any combustible construction.

Ignition

A grounded, 3-prong outdoor GFI outlet is to be located inside

the island cabinet and to the left of the Power TM burner. See

"Electrical Requirements" section.

t A q

T-

® ©

A. 18_" (47.9 cm)

B. 10%" (27.0 cm)

C. 22 z_,,(58.1 cm)

D. 23%" (60.0 cm)

E. 22¼" (56.5 cm)

F. Manifold pipe

G. 3¼" (8.3 cm)

H. 191_,, (50.0 cm)

I.201_,, (53.2 cm)

Built-In Outdoor Power TM Burner Enclosure

This built-in outdoor Power TM burner is for installation in a built-in

enclosure constructed of combustible and noncombustible

materials. Some types of noncombustible materials could be

brick, firewall or steel. Some types of combustible materials

could be wood or laminate.

The enclosure for the built-in outdoor Power TM burner is to be a

minimum of 11" (28.0 cm) high x 20" (50.8 cm) deep x

19" (48.6 cm) wide.

Counterorsupportsurfacesmustbelevel.

TheinstallationofthisPowerTM burner must conform with local

codes or, in the absence of local codes, with either the National

Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and Handling

Code, B149.2.

Copies of the standards listed may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

NOTE: The outdoor Power TM burner drops into the enclosure

opening and is supported by its side flanges. No bottom support

is needed.

The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor

products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and

minimum spacing must be followed.

E Gri!ls orrnent C

Refre_"

H A

Between 2 or more sets of Access Doors adjacent to each other:

K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a Trash Drawer, Utility Drawer, or Warming Drawer:

K = 3" (7.6 cm)

Cabinet Height and Depth Dimensions

With outdoor refrigerator

Grill with insulated jacket

Grill without insulated jacket

Dimension A Minimum

37" (94.0 cm)

361/2'' (92.7 cm)

351/2"(90.2 cm)

Dimension B Minimum

26" (66.0 cm)

27" (68.6 cm)

26" (66.0 cm)

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 29%" (75.2 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)

36" (91.4 cm) 388/8'' (98.1 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)

48" (121.9 cm) 50%" (128.6 cm) 103_'' (27.3 cm) 227/8'' (58.1 cm)

Cutout Dimensions - Built-in Grill with Insulated Jacket

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 33" (83.8 cm) 11%" (29.8 cm) 24" (61.0 cm)

36" (91.4 cm) 42" (106.7 cm) 11%" (29.8 cm) 24" (61.0 cm)

48" (121.9 cm) 54" (137.2 cm) 11%" (29.8 cm) 24" (61.0 cm)

Cutout Dimensions - Built-in Power TM Burner

Dimension C Dimension D Dimension E

193/8'' (49.2 cm) 103A'' (27.3 cm) 193A'' (50.2 cm)

Cutout Dimensions - Built-in Side Burner

Burner Position Dimension C Dimension D Dimension E

Front to Back 131/2'' (34.3 cm) 10%" (27.3 cm) 228/8'' (57.5 cm)

Side by Side 241/2'' (62.2 cm) 103_'' (27.3 cm) 167/8'' (42.9 cm)

Dimension C Dimension D Dimension E

131/2'' (34.3 cm) 10%" (27.0 cm) 221Vie'' (57.6 cm)

Cutout Dimensions - Built-in Refreshment Center

Dimension C Dimension D Dimension E

301/2'' (77.5 cm) 10%" (27.3 cm) 23" (58.4 cm)

Cutout Dimensions - Built-in Access Doors

Door Size Dimension F Dimension L*

18" (45.7 cm) 163/16"(41.1 cm) 11/2"(3.8 cm)

27" (68.6 cm) 251/8'' (63.8 cm) 11/2"(3.8 cm)

30" (76.2 cm) 281/8'' (71.4 cm) 11/2"(3.8 cm)

36" (91.4 cm) 341/8'' (86.7 cm) 11/2"(3.8 cm)

48" (121.9 cm) 461/8'' (117.2 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Dimension G Dimension H

24" (61.0 cm) 35W' (89.5 cm)

Cutout Dimensions - Outdoor Ice Maker

Dimension G Dimension H

18" (45.7 cm) 34" (86.4 cm) min. to 341/2'' (87.6 cm) max.

Cutout Dimensions - Built-in Warming Drawer

Warming Drawer Size Dimension J

24" (61.0 cm) 221/2'' (57.2 cm)

Dimension M Dimension L*

12W' (31.1 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Built-in Outdoor Grill Enclosure Ventilation for LP Gas:

An enclosure for an LP gas fuel tank is to be ventilated by

openings at both the top and lower levels of the enclosure.

If converting to LP gas, these vents are to be in the

enclosure:

An enclosure for use with an LP gas fuel tank for built-in

installation is to have at least one ventilation opening on an

exposed exterior side located within 5" (12.7 cm) of the top is to

be a minimum of 20 in.2 (129.0 cm2). One ventilation opening

within 1" (2.5 cm) of the bottom of the enclosure and the bottom

opening is to be a minimum of 10 in.2(64.5 cm_).All vent

openings are to be unobstructed. Every opening is to be a

minimum of 1/8"(0.32 cm) wide.

20 in.2(129.0 crn 2) rain.

ventimation both sides

1" (2.5 crn)

10 in? (64.5 crn 2)

ventilation both sides

5" (12.7 crn) max.

"_' (12.7 crn) max.

£:i',l@CI (;.a/_,.@;]!

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

Power TM burner is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that aseparate circuit servicing only this

Power TM burner be provided.

• To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

• Unplug from the outlet when not in use and before

cleaning. Allow to cool before putting on or taking off

parts.

Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner.

Contact the manufacturer for repair.

• Do not let the cord hang over the edge of a table or touch

hot surfaces.

• Do not use an outdoor cooking appliance for purposes

other than intended.

• When connecting, first connect plug to the outdoor

cooking gas appliance then plug appliance into the outlet.

• Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

• Do not remove the ground prong or use with an adapter

of 2 prongs.

The model/serial number rating plate is located on the right-hand

side panel. See the following illustration.

A. Model/serial number plate

Recommended Ground Method

The outdoor Power TM burner, when installed, must be electrically

grounded in accordance with local codes or, in the absence of

local codes, with the National Electrical Code ANSI/NFPA 70, or

Canadian Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

S ..............................

A ......................

A. 3 prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

"" _f ; _'_'_ /s /s ,/ _ ..................

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149.1 - latest

edition.

IMPORTANT: The Power TM burner must be connected to a

regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

GasConversion:

NoattemptshallbemadetoconvertthePowerTM burner from

the gas specified on the model/serial rating plate for use with a

different gas type without consulting the serving gas supplier. The

conversion kits supplied with the Power TM burner must be used.

See "Gas Conversions" section for instructions.

Gas Pressure Regulator

The gas pressure regulator supplied with this Power TM burner

must be used. The inlet (supply) pressure to the regulator should

be as follows for proper operation:

LP Gas:

Set pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Set pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7' to 14" (17.8 cm to 35.5 cm)

WCP maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The Power TM burner and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures greater than

1/2psi (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or

lower:

The Power TM burner must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2psi (3.5 kPa).

20 Ib LP Gas Fuel Tank

This Power TM burner is equipped for use with a 20 Ib LP gas fuel

tank (fuel tank not supplied). A gas pressure regulator/hose

assembly is supplied.

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

A. Gaspressure regulator/hose assembly

The 20 Ib LP gas fuel tank must be mounted and secured.

Door Style Tank Tray

1. Open cabinet doors.

2. Pull out the tank tray.

Tank tray

3. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

B C

A. Locking screw

B. Mounting hole

C. Bottom collar

5. Slide tank tray back into the cabinet.

6. Close cabinet doors.

Local LP Gas Supply Conversion

Conversion must be made by a qualified gas technician. The

qualified gas technician shall provide the gas supply to the

selected Power TM burner location in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition,

and local codes. For conversion to local LP, the convertible

regulator in the conversion kit supplied with the Power TM burner

must be used.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified

LP gas technician shall provide the LP gas supply to the selected

Power TM burner location in accordance with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 and local codes.

Follow instructions for converting to local LP gas in the "Gas

Conversions" section.

A. New CSAInternational approved

"outdoor" flexiblegas supply line

B. Rear of Power TM burner

C. Tolocal LP gassupply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the

Power TM burner and should be in a location that allows ease of

opening and closing. Do not block access to the shutoff valve.

The valve is for turning on or shutting off gas to the Power TM

burner.

A. Gas supply line

B. Shutoff valve "open" position

C. To Power TM burner

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected Power TM burner location in accordance

with the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest

edition, and local codes. For conversion to Natural gas, the

Natural gas conversion kit supplied with the Power TM burner

must be used.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

To convert to Natural gas, the Natural Gas Conversion Kit

supplied with the Power TM burner must be used. Follow

instructions for converting to Natural gas in the "Gas

Conversions" section.

_:::::::::::::::::::::) _ ,

A. New CSA International approved

"outdoor" flexible gas supply fine

B. Rear of Power TM burner

C. To Natural gas supply

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the

Power TM burner and should be in a location that allows ease of

opening and closing. Do not block access to the shutoff valve.

The valve is for turning on or shutting off gas to the Power TM

burner.

A. Gas supply line

B. Shutoff valve "open" position

C. To Power TM burner

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install side

burner.

Failure to do so can result in back or other injury.

1. Position the tank tray for 20 Ib LP gas fuel tank in the island

cabinet.

Unpack Power TM burner. Remove all packaging materials and

remove Power TM burner from carton.

Place Power TM burner into outdoor enclosure, but leave

enough room in back to connect to gas supply and electrical

single prong plug-in.

centerline of

tank tray

20%"

(52.4 crn)

18%"

21/4 It

(5.7 crn)

A. 8%2" (20.6 cm)

B. 16_" (41.1 cm)

2. Square the tank tray mounting brackets and mark the

mounting hole locations in the island base.

3. Remove the top nuts (4) from the tank tray assembly and lift

the tank tray off of the mounting brackets.

The tank tray for the 20 Ib LP gas fuel tank must be adjusted

so that the bottom of the tank tray is %" (0.32 cm) above the

cabinet door opening and is level. The top nut on each of the

mounting brackets is to be loose. Turn the bottom nuts

counterclockwise to raise the tank tray and turn the bottom

nuts clockwise to lower the tank tray. When the tank tray is

level and slides in and out without touching the cabinet door

opening at the bottom or top with the 20 Ib LP tank installed,

tighten the top nuts against the adjustment flange.

A. Top nut

B. Tank tray

C. Bottom nut

D. Bolt

E. Mounting bracket

Install the tank tray mounting brackets to the base or floor of

the island using the proper size and type of mounting

hardware (not supplied). Tighten mounting hardware.

g /

A. Screw (Use proper screw for island floor material.)

B. Lock washer

C. Flat washer

5. Pre-adjust each of the bottom nuts on the mounting brackets

to 3" (7.6 cm) from the base of the island to the top of the

nuts.

6. Remount the tank tray back onto the mounting brackets.

Replace the 4 top nuts but do not tighten.

A. 20 Ib LP gas fuel tank

B. Tank tray for 20 Ib gas fuel tank

C. Top nut (do not tighten)

D. Mounting bracket

A. Top nut loosened

B. Top nut tightened

NOTE: A bracket or shelf (not supplied) that is large enough

to keep a second 20 Ib LP gas fuel tank from being stored in

the storage area under the Power TM burner is required to be

mounted inside the island.

Make Gas Connection

Gas Connection to a 20 Ib LPGas FuelTank

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

If converting to local LP or Natural gas, follow the instructions in

the "Gas Conversions" section.

IMPORTANT: A 20 Ib LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the Power TM burner must be used. Replacement

gas pressure regulator/hose assembly specific to your model, is

available from your outdoor Power TM burner dealer.

To Install the 20 Ib LP Gas Fuel Tank:

1. Open cabinet doors.

2. Pull out the tank tray.

Tank tray

3. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

Gas Connection to Natural Gas or Local LP Gas

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

B C

A. Locking screw

B. Mounting hole

C. Bottom collar

Screw the gas pressure regulator/hose assembly to the 20 Ib

LP gas fuel tank as shown. (To disconnect, turn off the gas

supply to the 20 Ib LP gas fuel tank, then unscrew the gas

pressure regulator/hose assembly from the 20 Ib LP gas fuel

tank as shown.

A.20 Ib LP gas fuel tank

B.Gaspressure regulator/hose assembly

6. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

7. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

8. Slide tank tray back into the cabinet.

9. Go to "Plug in Power TM Burner" in this section.

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1 - latest edition, or

CAN/CGA-B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

1. Make gas connections.

A combination of pipe fittings must be used to connect the

Power TM burner to the existing gas line.

If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA

International, to connect the Power TM burner to the rigid

gas supply line. A %" diameter line is recommended.

Using a wrench to tighten, connect the gas supply to the

Power TM burner. Use pipe-joint compound on all non-

flared male threads. Do not kink or damage the flexible

connector when moving the Power TM burner.

• Pipe-joint compounds suitable for use with LP gas must

be used. Do not use TEFLON ®ttape.

A. New CSA International approved

"outdoor" flexible gas supply line

B. Rear of Power TM burner

C. To Natural gas or local LP gas supply

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

2. Open the manual shutoff valve in the gas supply line. The 4. Gently slide the Power TM burner completely into the outdoor

valve is open when the handle is parallel to the gas pipe. enclosure.

A. Closed valve

B. Open valve

Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

Plug in Power TM Burner

NOTE: This built-in outdoor Power TM burner comes with a large

2,085 mAmp power transformer/plug assembly for the Power TM

burner igniters. Follow the instructions for plugging in and

mounting the power transformer. Keep any electrical supply cord

away from any heated surfaces.

1. Plug the single-prong plug into the receptacle on the left

underside of the Power TM burner.

A. Single-prong plug

Locate or build a non-combustible surface inside the island

cabinet to mount the power transformer. It must be to the left

side of the Power TM burner at a minimum of 3" (7.6 cm) from

the side and 4" (10.2 cm) below the bottom of the Power TM

burner.

Mount the power transformer to the mounting surface using

4 #8 screws (not supplied) that are the proper type and length

for the transformer and the mounting surface. It must be

mounted with the wire for the single-prong plug upward or

toward the Power TM burner.

NOTE: The cord must be properly mounted with a cord

retention device so that its 3-prong plug will not touch the

ground when it is unplugged.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug 3-prong power cord plug into a grounded 3-prong GFI

outlet.

• To avoid electrical shock, do not immerse cord or plugs in

water or other liquid.

• Unplug from the outlet when not in use and before

cleaning. Allow to cool before putting on or taking off

parts.

Do not operate any outdoor cooking gas appliance with a

damaged cord, damaged plug, or after the appliance

malfunctions or has been damaged in any manner.

Contact the manufacturer for repair.

• Do not let the cord hang over the edge of a table or touch

hot surfaces.

• Do not use an outdoor cooking appliance for purposes

other than intended.

When connecting, first connect plug to the outdoor

cooking gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected circuit

with this outdoor cooking gas appliance.

Do not remove the ground prong or use with an adapter

of 2 prongs.

Assemble Cooking Area

1. Lift off cover and grate and set aside.

A. Cover

B. Grate

2. Remove packing from around burner. 3. Remove plastic bags from grate and film from cover.

4. Reinstall grate.

5. Dispose of/recycle all packaging materials.

6. Go to the "Check and Adjust the Burners" section.

GAS CONVERSIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Pipe wrench

• Adjustable wrench

• 10 mm socket and wrench

or 10 mm nut driver

• Thin flat-blade screwdriver

• Pliers

• Pipe thread sealant

certified for LP gas

Parts supplied

• Brass connector

• Convertible regulator 4" W.C. Natural, 11" W.C. LP

• Natural gas orifices

IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas

supply to the appliance prior to disconnecting the electrical

power.

This kit is designed for use from sea level up to 2000 ft elevation.

For higher elevations contact KitchenAid at 1-800-422-1230 in

the U.S.A. or call 1-800-607-6777 in Canada.

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug Power TM burner or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Use adjustable wrench to remove LP hose regulator from

brass elbow. Use adjustable wrench to remove brass elbow.

A. Manifold

B. Brass elbow

C. Rear of Power TM burner

D. Gas pressure regulator/hose assembly

Apply pipe sealant to the threads of the brass connector. Use

pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to

manifold fitting.

NOTE: The arrow on the regulator must be pointing toward

the brass connector.

_m_ _'_I?',

iiiii!Y

Use pipe wrench to install the convertible regulator. Brass

cap will be facing up when tight.

A B

A, Brass connector

B. Convertible regulator

To set the appliance regulator for LP gas, use adjustable

wrench to remove the brass cap on the convertible regulator.

10. Examine the stem on the brass cap. The letters "NAT" should

be showing on the end of the plastic stem farthest away from

the brass cap.

11. Remove stem from cap, turn it over and snap stem back into

the cap so the letters "LP" are at the end of the stem farthest

away from the brass cap.

12. Use adjustable wrench to reinstall cap onto regulator.

Make Power TM Burner Connections

Connect Local LP Gas Supply

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply

pipe to inlet side of regulator from Fixed LP gas supply

according to local codes requirements. Use pipe thread

sealant that is certified for use with LP gas at connections

where required. There must be a certified manual shutoff

valve in the gas supply line near the Power TM burner for easy

access.

2. Turn on the gas supply to the Power TM burner.

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leaks found.

Record Conversion

In the last page of the Use and Care Guide, write "Converted to

Local LP Gas Supply." Also record the conversion date and the

technician/company that performed the conversion.

Installation of the regulator

1. Turn off the main gas supply valve.

2. Unplug Power TM burner or disconnect power.

3. Disconnect 20 Ib LP gas fuel tank (if present).

4. Turn off all burner control valves.

5. Use adjustable wrench to remove LP hose regulator from

brass elbow. Use adjustable wrench to remove brass elbow.

A .................

A. Manifold

B. Brass elbow

C. Rear of Power TM burner

D. Gaspressureregulator/hose

assembly

Apply pipe sealant to the threads of the brass connector. Use

pipe thread sealant that is certified for use with LP gas.

Use adjustable wrench to install brass connector (supplied) to

manifold fitting.

NOTE: The arrow on the regulator must be pointing toward

the brass connector.

Use pipe wrench to install the convertible regulator. Brass

cap will be facing up when tight.

A B

ii( 'iiiiiiiiD

A. Brass elbow

B. Convertible regulator

To make sure the regulator is set for Natural gas, use

adjustable wrench to remove brass cap on appliance

regulator.

10. Examine the stem on the brass cap. If the letters "NAT" are

not showing on the end of the plastic stem farthest away from

the brass cap, remove stem from cap, turn it over and snap

stem back into the cap so the letters "NAT" are at the end of

the stem farthest away from the brass cap.

11. Reinstall cap onto convertible regulator.

Change the Power TM burner orifices

1. Remove the Power TM burner grate.

2. Remove the wok ring. Twist counterclockwise, lift, and set

aside.

Remove inner burner top ring from burner base.

Remove outer burner top ring from burner base.

A. Inner burner

B. Outer burner

C. Burner base

Remove the burner base.

a. Lift rear of burner to remove Iocator pin from Iocator hole.

b. Gently pull the burner base to the rear to disengage the

burner from the gas valves and openings.

IMPORTANT: The igniter is connected to the burner base.

Make sure the wires do not get pulled from the ignition.

c. Rotate burner base 90° and place in the bottom of the

burner box.

A. Igniter wire

6. Use a 10 mm socket and wrench or 10 mm nut driver to

remove the brass orifices from the gas valves.

A. Inner burner

B. Outer burner

Use a 10 mm socket and wrench or 10 mm nut driver to

install the new 2.06 mm (inner burner) and 2.78 mm (outer

burner) brass orifices supplied with this kit.

NOTE: The number 2.06 and 2.78 are stamped on the orifices

for identification.

Replace the burner base. Insure the Iocator pin locks into the

Iocator hole.

A. Locator pin

Replace outer burner top ring, locate with the igniter slot over

the igniter.

A.Igniter

10. Replace inner burner top ring.

11. Replace the wok ring, locate the tabs to the slots and twist

clockwise to secure.

12. Replace burner grate.

Hook up to Natural gas and Leak Test

1. Use pipe wrench to connect certified 1/2"(1.3 cm) gas supply

pipe to inlet side of regulator from Natural gas supply

according to local codes requirements. Use pipe thread

sealant that is certified for use with LP gas at connections

where required. There must be a certified manual shutoff

valve in the gas supply line near the grill for easy access.

2. Turn on the gas supply to the grill.

3. Test all connections using an approved noncorrosive leak-

detection solution. Bubbles will show a leak. Correct any leak

found.

Record Conversion

The Power TM burner nameplate is located on the right-hand side

panel. With a permanent marker, check the box next to "Natural

gas" and mark through "LP - Propane."

In the last page of the Use and Care Guide, write "Converted to

Natural Gas." Also record the conversion date and the

technician/company that performed the conversion.

NOTE: Place LP gas parts in plastic parts bag for future use and

keep with pack containing literature.

........ .......... : +

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to low flame setting necessary.

It is recommended that a qualified person make burner

adjustments.

A. 4" (10.2 cm) for outer burner when set to "HI."

B. 3" (7.6 cm) for inner burner when set to HI."

Low Flame Adjustment

If flame goes out on the "LO" setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until burners are cool.

2. Light Power TM burner using information in the "Outdoor

Power TM Burner Use" section.

3. Turn burner to its lowest setting and remove knob.

4. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

5. Watch the flame and slowly turn the screwdriver

counterclockwise.

6. Adjust flame to minimum stable flame.

A. Valve stem

B. Small flat-blade screwdriver

C. Priers

7. Replace the control knob and turn off the burner.

8. Repeat steps 3 through 7 for each burner if needed.

USING YOUR OUTDOOR PO C-ER TMBURNER

Inspect the LP Gas Fuel Tank Supply Hose Wok Ring

Inspect the gas pressure regulator/hose assembly before each

use.

1. Open the cabinet door and slide 20 Ib LP gas fuel tank out.

2. Inspect the entire gas pressure regulator/hose assembly for

cuts, abrasions, or excessive wear.

3. If necessary, replace the gas pressure regulator/hose

assembly before using the Power TM burner.

Contact the dealer and use only replacement hoses specified for

use with the Power TM burner.

A. Gas pressure regulator/hose assembly

Prepare the Gas Supply

1. Remove outdoor Power TM burner cover.

2. Make sure the control knobs are all turned to the OFF

position.

Turn the Gas Supply On

NOTE: The Power TM burner can be used with or without the wok

ring. Without the wok ring, the heat zone expands to the edges of

the grate.

IMPORTANT: Before removing the Power TM burner grate, make

sure the gas supply is Off, all controls are in the Off position, and

the Power TM burner is cool.

To Remove the Wok Ring

1. Remove the Power TM burner grate.

2. Remove the wok ring. Twist counterclockwise, lift, and set

aside for future use with a Wok.

3. Replace burner grate.

To Replace the Wok Ring:

1. Remove the Power TM burner grate and set aside for future

use.

2. Set the wok ring into the notches in Power TM burner frame.

Twist clockwise to secure.

1. For outdoor Power TM burners using a 20 Ib LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your Power TM burner

may not light. If your Power TM burner does light, the flames

will be low and will not heat properly. Turn 20 Ib LP gas fuel

tank valve and all control knobs off and wait 30 seconds.

After shutting off the 20 Ib LP gas fuel tank, very slowly open

tank valve and wait 5 seconds before lighting.

2. For outdoor Power TM burners using gas supply source other

than 20 Ib LP gas fuel tank:

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

The Power TM Burner, depending on your need can be used with:

• The inner burner provides the lowest amount of heat for

cooking smaller quantities of food or liquid using smaller pots

and pans.

• The outer burner provides high heat for cooking large

quantities of food or liquid using large pots and pans.

• Both inner and outer burners together provide extra-high heat

for cooking extra-large quantities of food or liquid using

extra-large pots and pans.

3. Place Wok onto wok ring.

_,_ih_::ii_.... _ _i_ i_ow_i_:i'_¸_¸¸_¸_......._ _ _

Burn Hazard

Do not let the burner flame extend beyond the edge of

the pan.

Doing so can result in burns.

Manually lighting the Power TM burner

1. Remove the outdoor Power TM burner cover.

2. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

1. Remove the Power TM burner cover. Do not light burners with

the cover on.

2. Do not lean over the Power TM burner.

3. Push in and turn the control knob for the inner or outer burner

to LITE/HI and hold in.

3. Strike the match to light it.

4. Guide the match to the burner you wish to light.

5= Do not lean over the Power TM burner. Push in and turn the

burner knob to LITE/HI for the burner you wish to light. The

burner will light immediately. When burner is lit, turn knob to

desired setting.

4. You will see the igniter glow. When burner is lit, release the

knob. Turn knob to desired setting.

5. Repeat for the other burner as needed.

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

6. Repeat for each of the other burners as needed.

7. Remove match and replace manual lighting extension inside

its holder.

IM PORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to manually light them,

contact the KitchenAid Customer eXperience Center. See the

"Assistance or Service"

La page charge ...

KitchenAid KBPU182VSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBPU182VSS00

Taper: Le manuel du propriétaire

Ce manuel convient également à

POWER KBPU182VSS

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KBPU182VSS00 Owner's manual

KitchenAid KBPU182VSS00 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KBPU182VSS00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents