Date Issued: 02/16/17
IS-43953-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
STEM(S)
SHORT THREADED PIPE
CAP
►
GLASS
SOCKET
SWIVEL
STEEL WASHER
NEOPRENE WASHER
MOUNTING SCREWS
OUTLET BOX
WIRE
CONNECTORS
STRAP MOUNTING
SCREWS
MOUNTING STRAP
CANOPY
LOCK-UP KNOBS
LOCKWASHERS
LOOP
CHAIN LINK
HEXNUT
LOCKWASHER
THREADED PIPE
LOOP/CHAIN LINK
►
THREADED PIPE
LOCK-UP KNOBS
LOCKWASHERS
STEM(S)
OUTLET BOX
WIRE
CONNECTORS
STRAP MOUNTING
SCREWS
HEXNUT
LOCKWASHER
RIGID STEM MOUNT
CAUTION – RISK OF SHOCK – DISCONNECT POWER AT
THE MAIN CIRCUIT BREAKER PANEL OR MAIN FUSE BOX
BEFORE STARTING AND DURING THE INSTALLATION.
LOOP/CHAIN LINK INSTALLATION
1) Insert steel washer all the way into the slot on the swivel.
2) Slip the flexible washer onto the steel washer.
3) Pass the fixture wire up through the glass and out through the
top.
4) Pass the fixture wire through the cap and out the narrow end.
5) Pass wire through a stem on the end with a short threaded
pipe.
6) Raise the socket into the glass. Rest the inside of the top of
the glass onto the washers.
7) Rest the cap onto the top of the glass.
8) Screw the stem to swivel on top of fixture body (inside the
cap). NOTE: Thread locking compound must be applied to all
stem threads as noted with symbol () to prevent accidental
rotation of fixture during cleaning, relamping, etc.
9) Pass wire through stem and screw stem to coupling on top of
fixture body. NOTE: Thread locking compound must be applied
to all stem threads as noted with arrow symbol to prevent
accidental rotation of fixture during cleaning, relamping, etc.
10) Pass wire through remaining stems and screw stems together.
11) Pass fixture wire through first loop. Thread first loop onto end
of last stem.
12) Pass threaded pipe at end of second loop through hole in
canopy. Thread lockwasher onto threaded pipe protruding from
inside canopy. Pass fixture wire through hole in hexnut and
thread hexnut onto end of threaded pipe.
13) Attach chain link to small loop at end of stem and to loop on
canopy. Close chain link ends together using chain pliers or
padded pliers to prevent damage to finish.
14) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
15) Attach mounting strap to outlet box.
Mounting strap can be adjusted to suit position of fixture.
16) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Put ground
wire from outlet box under cupped washer and green
ground screw and thread screw into hole in mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector,
(not provided) after following the above steps. Never con-
nect ground wire to black or white power supply wires.
17) Make wire connections. Reference chart below for correct
connections and wire accordingly.
18) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy. NOTE: Be certain wires do not get
pinched between mounting plate and canopy.
19) Slip lockwashers over mounting screws. Thread lock-up
knobs onto mounting screws. Tighten lock-up knobs to
secure fixture to ceiling.
20) Insert recommended bulb (Not supplied).
RIGID STEM INSTALLATION
1) Follow steps 1-9 from “Loop/Chain Link Installation”.
2) Make sure last stem has small threaded pipe attached.
3) Remove hexut, lockwasher, and loop from canopy.
4) Pass fixture wire through hole in canopy. Pass hole in canopy
down over threaded pipe on top of fixture body.
5) Pass lockwasher onto threaded pipe protruding from inside
of canopy and screw hexnut onto threaded pipe. Tighten to
secure.
6) Follow steps 14-20 from “Loop/Chain Link Installation”.
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada