Kodak Advantix F320 Manuel utilisateur

Taper
Manuel utilisateur
F320/F330 AutoCamera
Consumer Imaging
EASTMAN KODAK COMPANY
Rochester, NY 14650
Kodak
Camera Identification
Unfold front and back cover flaps of manual to view camera diagrams.
ENGLISH/ESPAÑOL/FRANÇAIS
1 shutter button
2 self-timer button
3 LCD panel
4 viewfinder
5 self-timer bulb
6 flash
7 lens-cover switch
8 lens
9 film-door lever
15 film chamber
16 film door
17 tripod socket
18 battery door
1
2
3
4
9
6
7
8
5
15
18
16
17
© Eastman Kodak Company, 2001
Pt. No. 919 6403 Printed in USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
NOTE: Your model camera has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits provide reasonable
protection against interference in residential use. The camera generates, uses and can
radiate radio frequency energy and, if not used in accordance with the instructions, may
cause interference to radio communications. There is no guarantee that interference will
not occur. If this camera does cause interference to radio or television reception, which
can be determined by turning the camera off and on, you may reduce the interference by
the following:
— Reorient or relocate the receiving antenna.
— Increase the separation between the camera and the receiver.
— Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
19
LCD Panel
20
21
10 print-format
switch
11 viewfinder
eyepiece
12 film-rewind button
13 flash-ready lamp
14 strap post
19 self-timer indicator
20 picture counter
21 battery symbol
10
11
13
14
12
1
Kodak
ENGLISH
F320/F330 Auto Camera
NEED HELP WITH YOUR CAMERA OR MORE INFORMATION
ABOUT THE ADVANCED PHOTO SYSTEM?
Go to our Web site at http://www.kodak.com (for US) or
http www.kodak.ca (for Canada) or call: Kodak (US only) from
9:00 a.m. to 7:00 p.m. (Eastern time) Monday through Friday
at 1-800-242-2424.
Kodak (Canada only) from 8:00 a.m. to 5:00 p.m. (Eastern time)
Monday through Friday at 1-800-465-6325, ext. 36100; for the
Toronto area, call 416-766-8233, ext. 36100. When you call,
please have your camera available.
For warranty purposes, please keep your sales receipt as
proof of the date of purchase.
2
CONTENTS
CAMERA FEATURES ................ 3
ATTACHING THE STRAP .......... 4
LOADING THE BATTERIES ...... 5
Low-batteries indicator......... 6
Battery tips .......................... 6
Power shutdown................... 7
LOADING THE FILM ................. 8
TAKING PICTURES ................ 10
Typical print sizes
(formats) .......................... 12
Tips for better pictures ...... 13
TAKING FLASH PICTURES .... 14
Flash-to-subject distance .. 15
USING THE SELF-TIMER ....... 15
UNLOADING THE FILM .......... 16
Automatic rewind ............... 16
Manual rewind .................... 17
CARING FOR
YOUR CAMERA .................... 18
TROUBLESHOOTING ............. 19
SPECIFICATIONS ................... 21
3
CAMERA FEATURES
Three Print Formats
You can take three different
size pictures: Classic (C), Group/
HDTV (H), and Panoramic (P)
pictures from the same film
cassette. The viewfinder
changes to show the selected
picture size.
Double Exposure Protection (DEP)
You dont need to worry about
accidentally re-exposing your
film. Your camera reads the
Film Status Indicator (FSI) on
the film cassette to prevent
double exposures.
Easy, Drop-in Loading
Easy, drop-in loading is fast
and virtually error-free. The
camera uses KODAK ADVANTIX
Film. The film cassette com-
municates the status of film
and becomes the carrier and
storage container for the
processed film.
Safety-Locked Film Door
After you close the safety-
interlocked film door and the
film starts to prewind, you
cannot open the door until the
film is completely rewound into
the film cassette.
4
ATTACHING THE STRAP
Thread the shorter looped end
of the strap under the strap
post (14); pull the longer end
through the shorter loop and pull
it tight.
Film Status Indicator (FSI)
A highlighted indicator
advances from one symbol to
another to identify the status
of the film inside the cassette.
4
3
2
1
Processed negatives
Unexposed
Partially exposed
Fully
exposed
5
Before you remove the old
batteries, close the lens cover.
LOADING THE BATTERIES
This camera uses 2 AAA-size
batteries that supply power for all
camera operations.
1.Open the battery door (18).
2. Place the batteries over the
battery-pull strap and insert
into the chamber as shown.
3. Snap the battery door closed.
NOTE: Insert the batteries into
the camera before you load
the film.
6
Keep batteries away
from children.
Do not try to take apart,
recharge or short circuit the
batteries, or subject them to
high temperature or fire.
Do not use rechargeable
batteries.
Store batteries in their original
packaging prior to use.
Remove the batteries from the
camera when the camera is
not going to be used for an
extended length of time.
Replace all batteries with the
same brand and grade and as
a set at the same time.
Low-batteries indicator
Its time to replace the batteries
when the battery symbol (21)
appears on the LCD panel (3) or
when the flash-ready lamp (13)
takes longer than 12 seconds to
turn on.
Battery tips
Dispose of batteries according
to local and national regulations.
Remember to keep spare
batteries with you at all times.
Read and follow all warnings
and instructions supplied by
the battery manufacturer.
7
In the unlikely event that
battery fluid leaks onto your
skin, contact Kodak Health,
Safety and Environment
Information at 1-716-722-5151
in the U.S. Customers outside
the U.S. can contact their local
health care provider.
In the unlikely event that
battery fluid leaks inside the
camera, U.S. customers can
contact the Kodak Information
Center (KIC) at 1-800-242-
2424. Customers outside the
U.S. can contact their local
Kodak Customer Service
representative.
Power shutdown
To conserve battery power, the
camera automatically goes into a
sleep mode if it is not operated
for more than 4 minutes. You can
awaken the camera by taking a
picture or by closing and
reopening the lens cover. When
the camera will not be used for an
extended length of time, close
the lens cover to completely turn
off the camera.
8
The film door opens only
when the film chamber is
empty or the film in the
camera is completely
rewound into the film cassette.
2. Insert the film cassette
completely into the film
chamber (15).
LOADING THE FILM
You can load film into the camera
with the camera ON or OFF.
Insert the batteries into the camera
before you load the film.
1. Move the film-door lever (9) to
open the film door (16).
9
Look for this logo to be certain that the film
you buy is made for this camera.
Look for this logo to select a certified
photofinisher for developing your film and to
assure that you get all the features of the
Advanced Photo System.
Make sure the Film Status
Indicator (FSI) on the film
cassette is at
(#1 position)
for a new cassette.
Do not force the film
cassette into the film chamber.
3. Close the film door to start the
automatic film prewind. The
picture counter (20) on the LCD
panel (3) displays the number
of pictures remaining on
the film.
After you close the safety-
interlocked film door and the
film starts to prewind, you
cannot open the door until
the film is completely
rewound into the film cassette.
10
TAKING PICTURES
You can take Classic (C), Group/
HDTV (H)*, and Panoramic (P)
pictures on the same film cassette. Your
photo-processing cost may be
based on the format size(s) that
you use to expose the film.
* High Definition Television (HDTV) prints
are the same aspect ratio as the TV for
CD interface capabilities.
1. Slide the lens-cover switch (7)
to uncover the lens (8) and
to turn on the camera.
11
3. Frame your subject within the
viewfinder eyepiece (11).
For a sharp picture, stand at
least 3.3 ft (1.0 m) from
your subject.
For low-light conditions, wait
until the flash-ready lamp (13)
turns green.
2. Move the print-format switch (10)
to select C, H, or P format.
The viewfinder changes to
show the selected field of view.
P
H
C
CH P
12
Typical print sizes (formats)
CH P
Classic Group (HDTV) Panoramic
3.5 x 5 in. or 4 x 6 in. 3.5 x 6 or 4 x 7 in. 3.5 x 8.5 in. to 4 x 11.5 in.
(88.9 x 127 mm or (88.9 x 152 mm or (88.9 x 216 mm to
102 x 152 mm) 102 x 178 mm) 102 x 292.7 mm)
NOTE:
Your photofinisher generally provides 4 x 6, 4 x 7, and 4 x 11.5 in.
(102 x 152, 102 x 178, and 102 x 292.7 mm) sizes. Some local printers may offer
3.5 x 5, 3.5 x 6, and 3.5 x 8.5 in. (88.9 x 127, 88.9 x 152, and 88.9 x 216 mm) sizes.
4. Press the shutter button (1)
to take the picture.
13
Tips for better pictures
Hold your camera steady
by keeping your elbows close
to your body when you press
the shutter button to avoid
blurry pictures.
Keep your pictures simple.
Move close enough to your
subject so that it fills the
viewfinder but not closer
than 3.3 ft (1.0 m).
Take pictures at the subjects
level. Kneel down to take
pictures of children and pets.
Keep the sun behind you.
This provides the best
subject illumination.
Hold your camera vertically to
capture tall, narrow subjects,
such as a waterfall, skyscraper,
or a single person.
Add interest to your picture by
framing it with a tree branch,
a window, or even the rails of
a fence.
Stand at an angle to shiny
surfaces like windows or
mirrors to avoid flash reflection
and bright spots in your pictures.
Turn on all the room lights and
have your subject look at the
lights. This helps to reduce red
eyes in flash pictures.
14
TAKING FLASH PICTURES
In dim light, such as indoors or
outdoors in heavy shade, or on
dark overcast days, you need
flash. Your camera has a built-in
automatic flash that fires
as needed.
Dont take pictures beyond
the maximum distance or
your pictures will be dark.
4. Wait for the flash-ready
lamp (13) to turn green.
5. Press the shutter button (1)
to take a picture.
1. Slide the lens-cover switch (7)
to uncover the lens (8) and
to turn on the camera.
2. Frame your subject within the
viewfinder eyepiece (11).
3. Keep the subject within the
distance range for the speed
of film in your camera (see
Flash-to-subject distance).
15
USING THE SELF-TIMER
Use this feature to include
yourself in pictures.
Flash-to-subject distance
ISO film Flash-to-subject
speed distance
100 3.3 to 10 ft
(1.0 to 3.1 m)
200 3.3 to 14 ft
(1.0 to 4.3 m)
400 3.3 to 18 ft
(1.0 to 5.5 m)
1. Attach a tripod to the camera
tripod socket (17) or place it on
a firm support.
2. Press the self-timer button (2).
The self-timer
indicator (19)
appears
on the LCD
panel (3).
3. Frame your
subject within
the viewfinder
eyepiece (11)
and allow room for yourself in it.
16
UNLOADING THE FILM
Automatic rewind
The camera automatically rewinds
the film into the cassette after
the last exposure.
1. Wait for the camera motor to
stop to ensure that the film is
completely rewound into the
film cassette.
The picture counter (20)
on the LCD panel (3) displays
0. The picture-counter
display disappears when the
lens cover is closed.
2. Move the film-door lever (9) to
open the film door (16).
4. Hold the camera steady and
gently press the shutter
button (1).
5. Quickly position yourself in the
composed picture making sure
that you see the self-timer
bulb (5).
The self-timer bulb glows and
then blinks during the last two
seconds of countdown.
To cancel the self-timer
selection before the shutter
releases, close the lens
cover.
The self-timer automatically
turns off after the shutter
releases.
17
3. Remove the film cassette from
the camera and reload with
new KODAK ADVANTIX Film.
The FSI on the fully-exposed
film cassette is at
(#3 position).
Manual rewind
If you dont want to take pictures on
the entire film, you can manually
actuate the automatic rewind.
1. Press the film-rewind button (12)
to start the
auto-film
rewind.
2. See
Automatic
rewind,
steps 13.
NOTE:
You cannot
reload partially exposed film
into this camera to continue
taking pictures.
18
CARING FOR YOUR CAMERA
Protect the camera from dust,
moisture, sudden impact, and
excessive heat.
CAUTION: Do not use solvents
or harsh or abrasive cleaners
on the camera body.
If the lens appears dirty,
breathe on it to form a mist
and wipe the surface gently
with a soft, lintless cloth or a
camera lens-cleaning tissue.
Never wipe a dry lens.
CAUTION: Do not use solvents
or solutions not designed for
cleaning camera lenses. Do
not use chemically treated
tissues intended for cleaning
eyeglasses.
Remove the batteries when
you store the camera for an
extended time.
CAUTION: To prevent possible
damage and electrical shock,
do not attempt to disassemble
or repair the camera or flash
unit by yourself.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82

Kodak Advantix F320 Manuel utilisateur

Taper
Manuel utilisateur