Halsey Taylor XP.A Le manuel du propriétaire

Halsey Taylor
Marque
Halsey Taylor
Modèle
XP.A
Taper
Le manuel du propriétaire
XP8W-Q*1A
97039C (Rev. A - 4/98)PAGE 1
HALSEY TAYLOR OWNERS MANUAL
USES HFC-134A REFRIGERANT
FIG. 1
5,6,7
2 - SEE FIG. 5
3,4
20
13
17
30
19,25,26
22
23
12
29
11,14
21
16
SEE FIG.3
27,28
XP8W-Q*1A
PAGE 297039C (Rev. A - 4/98)
FIG. 2
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA
REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE
MUR.
F = POWER CORD 4' (1219mm) LONG
CABLE ELÉCTRICO DE 4' (1219mm) PIE, DE LARGO
CORDON DALIMENTATION 4' (1219mm)
G = WALL SCREW HOLES
AGUJEROS DE TORNILLOS DE PARED
TROUS DE VIS DU MUR
H = 2 X 4 BLOCKING
BLOQUEO DE 2 X 4
BLOC 2 X 4
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2"
(38mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD
EMPLACEMENT DE LA PRISE DE COURANT
XP8W-Q*1A
97039C (Rev. A - 4/98)PAGE 3
CORRECT STREAM HEIGHT
FIG. 5
PUSH BUTTON VALVE ADJUSTMENT
FIG. 3
1
24
8
10
9
1,15,18
ADJUST THIS SCREW TO ELIMINATE VALVE LEVER "FREE PLAY"
OR CONTINUOUS FLOW FROM BUBBLER
STREAM HEIGHT
ADJUSTMENT SCREW
FIG. 4
CONDENSER WATER VALVE ADJUSTMENT
The condenser water valve is factory preset for a condenser water outlet temperature of 95° to 105° F.
If actual temperature varies greatly from this, readjust water flow rate at the valve using the following procedures.
1. START UP COMPRESSOR
This can be accomplished by depressing the cooler push button (See Fig. 1 - Item 3). Keep water
running during the entire readjustment procedure.
2. ADJUSTMENT CONDENSER WATER VALVE
Adjust valve by rotating adjustment stem. Rotating stem clockwise will increase water flow.
Counterclockwise rotation will decrease water flow. Increasing water flow will result in a lower
condenser outlet temperature, while decreasing water flow will result in a higher outlet temperature.
Proper adjustment is attained when condenser outlet temperature is 95° to 105° F.
XP8W-Q*1A
PAGE 497039C (Rev. A - 4/98)
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
ITEM NO.
PART NO. DESCRIPTION
15005C
51544C
10-15075-31-550
10-14534-31-640
10-26399-31-640
16-02705-08-640
17-14037-42-590
26860C
26861C
26862C
31513C
35790C
40136C
45340C
50986C
60-14181-51-550
66327C
61314C
45689C
66202C
75494C
55996C
45347C
55880C
55913C
55885C
35803C
35797C
401536242830
401536342830
401507442830
Nut-Regulator Retaining
Bubbler
Push Button Stem
Cap Push Button
Drain Plug
Strainer Plate
Basin
Regulator Lever
Pivot Bracket
Regulator Retaining Bracket
Cold Control
Compressor
Water Temperature Valve
Electrical Box-Cold Control
Regulator Holder
Condenser Assy
Evaporator
Regulator
Tailpipe Assy
Drier
Check Valve
Strainer
Electrical Box-Power Connection
Regulator Mounting Bracket
Adaptor-Drain
Nut 1-1/4 Slip Joint
Relay
Overload
Panel Side - Right
Panel Side - Left
Panel Front
ITEMIZED PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
NS
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water cool-
ers or orders for repair parts MUST include Model No. and Serial No. of
cooler, name and part number of replacement part.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Halsey Taylor XP.A Le manuel du propriétaire

Halsey Taylor
Marque
Halsey Taylor
Modèle
XP.A
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

Documents connexes