Skil ID572701 Le manuel du propriétaire

Marque: Skil

Modèle: ID572701

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

ID572702

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

Model/ Modelo/ Modèle: ID572701

1-877-SKIL-999

www.skil.com

20V 1/4'' Hex Impact Driver

Clé à chocs hexagonale de 1/4 po et de 20 V

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-5

Safety Warnings for Impact Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Symbols .....................................................6-9

Get to Know Your Impact Driver ..................................10

Specications .................................................10

Operating Instructions .......................................11-15

Maintenance ...................................................16

Troubleshooting ...............................................16

Limited Warranty of SKIL Cordless Tool ............................17

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool . Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool

in unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR IMPACT DRIVER

Hold the power tool by insulated gripping surfaces, when performing an operation

where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an electric

shock.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No-load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or

reciprocations per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Symbol Name Designation/Explanation

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR IMPACT DRIVER

20V 1/4'' Hex Impact Driver

Fig. 1

Quick-change

Collet

Variable-Speed

Trigger Switch

LED Light

Direction-of-Rotation Indicator

Direction-of-Rotation

(forward/center-lock/

reverse) Selector

Soft Grip

Removable Belt

Clip

SPECIFICATIONS

Rated voltage 20V d.c.

Collet size 1/4" Hex (power groove impact bits only)

No-load speed 0~2500 /min

Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)

Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack or charger in



uid or allow a



uid to



ow inside them. Corrosive or conductive



uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc, can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this impact driver or create accessories not

recommended for use with this impact driver. Any such alteration or

modication is misuse and could result in a hazardous condition leading to possible serious

injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the impact driver when

assembling parts, making adjustments, cleaning, or performing maintenance.

This cordless impact driver must be used only with the battery packs and chargers

listed below:

Battery Pack

Charger

2Ah 4Ah 5Ah

SKIL BY519701 SKIL BY519601 SKIL BY519603 SKIL SC535801

NOTICE: Please refer to the battery and charger manuals for detailed operating information.

To Attach/Detach Battery Pack

(Fig. 2)

Lock the variable-speed trigger switch “OFF”

on the tool by placing the direction-of-rotation

(forward/center-lock/reverse) selector in the

center position before attaching or detaching

the battery pack.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves in the tool, and then slide the battery

pack onto the tool.

To detach the battery pack:

Depress the battery-release button, located

on the front of the battery pack, to release the

battery pack. Pull the battery pack out and

remove it from the tool.

NOTICE: When placing the battery pack onto the tool, be sure that the raised rib on battery

pack aligns with the groove inside the tool and that the latches snap into place properly.

Improper attachment of the battery pack can cause damage to internal components.

WARNING

Battery tools are always in operating condition. Therefore, the

direction-of-rotation (forward/center-lock/reverse) selector should

always be locked in the center position when the tool is not in use or carrying it at your

side.

Fig. 2

Attach

Battery-Release

Button

Detach

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector

WARNING

After tool use, lock the direction-of-rotation selector in the “OFF”

position (center-lock) to help prevent accidental starts and possible

injury.

Your tool is equipped with a direction-of-rotation selector, located above the variable-speed

trigger switch. This selector is used to change the direction of rotation of the bit and to lock the

variable-speed trigger in the “OFF” (center-lock) position (Fig. 3).

a. Position the direction-of-rotation selector to the far right of the tool for forward rotation.

b. Position the direction-of-rotation selector to the far left of the tool for reverse rotation.

c. Position the switch in the “OFF” (center-lock) position to help reduce the possibility of

accidental starting when not in use.

NOTICE: To prevent gear damage, always allow the impact driver to come to a complete stop

before changing the direction of rotation.

NOTICE: The impact driver will not run unless the direction-of-rotation selector is engaged

fully to the left or to the right.

Fig. 3

Forward Reverse

Center-Lock

Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned "ON"

or "OFF" by depressing or releasing the vari-

able-speed trigger switch.

The variable-speed trigger switch delivers high-

er speed with increased trigger pressure and

lower speed with decreased trigger pressure

(Fig. 4).

LED Light

Your tool is equipped with an LED light, located

on the base of the tool. This provides additional

light on the surface of the work piece for

operation in lower-light areas.

The LED light will automatically turn on with a

slight squeeze on the variable-speed trigger

switch before the tool starts running, and will

turn off 8 to 12 seconds after the variable-

speed trigger switch is released.

The LED light will rapidly ash when the tool

and/or battery pack becomes overloaded or too

hot, and the internal sensors will turn the tool

off. Rest the tool for a while or place the tool

and battery pack separately under air ow for

to cool them.

The LED light will ash more slowly to indicate

that the battery is at low-battery capacity. Recharge the battery pack.

Fig. 4

Variable-Speed

Trigger Switch

Fig. 5

Removable Belt Clip (Fig. 6)

Your tool is equipped with a removable belt clip

that can be positioned on the left side of the

tool for convenient transport.

Install the belt clip onto the tool:

a. Remove the battery pack from the tool.

b. Align the rib of the belt clip with the threaded

hole on the base of the tool.

c. Insert the screw and securely tighten the

screw with a screwdriver.

Remove the belt clip from the tool:

d. Remove the battery pack from the tool.

e. Use a screwdriver to loosen the screw that

attaches the belt clip to the impact driver.

f. Remove the screw and the belt clip.

Install and Remove Bits

Your tool is equipped with a quick-change collet, making bit installation and removal very

easy.

Lock the variable-speed trigger switch “OFF” by placing the direction-of-rotation selector in the

center position.

To install the bit:

Pull the locking sleeve forward, insert the bit as far as it will go into the collet, and release the

locking sleeve to lock the bit. (Fig. 7)

To remove the bit:

Pull the locking sleeve forward. Pull the bit from the collet and release the sleeve.

Fig. 7

Locking Sleeve

NOTICE: Use only bits with power grooves; other bits can be used with a universal bit holder

that has power groove. Do not use bits that have a damaged shank.

WARNING

Use protective gloves when removing the bit from the tool, or rst

allow the bit to cool down. The bit may be hot after prolonged use.

Fig. 6

Tighten and Loosen Nuts and Bolts

Variable-speed control must be used with

caution for driving nuts and bolts with socket-

set attachments. The best technique is to start

slowly, increase speed as the nut or bolt runs

down, and then set the nut or bolt snugly by

slowing the tool to a stop. If this procedure is

not followed, the tool will have a tendency to

torque or twist in your hand when the nut or

bolt seats.

a. Install a suitable bit.

b. Apply just enough pressure to keep the bit

engaged on the screw or nut.

c. Apply minimal pressure to the variable-speed

trigger switch initially. Increase the speed

only when full control can be maintained.

NOTICE:

a. Always use the correct type and size of bit for your application.

b. When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a hole in

order to avoid cracking of the wood.

c. When screw driving in hard wood, one should pre-drill a hole.

WARNING

Do not over-tighten, as the force of the impact driver can break the

fastener. Keep the impact driver at a right angle to the fastener to

avoid damaging the fastener head.

Fig. 8

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air. Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch selectors must be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and house hold detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep it away from corrosive

agents.

TROUBLE SHOOTING

Problem Cause Remedy

Tool does not work. 1. Battery pack is depleted. 1. Charge the battery.

2. Tool is over-loaded. 2. Release the variable-speed trigger

switch and try again.

3. Battery pack is over-

temperature

3. Turn off the impact driver and cool

the battery pack under air



ow.

4. Battery pack is not installed

properly.

4. Conrm that the battery is locked

and secured to the tool.

5. Burned out switch. 5. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

Bit cannot be

installed.

Bit does not t the sleeve. Use a suitable bit or adapter.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

08/18

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs

aux outils électriques . .......................................19-21

Avertissements de sécurité pour la clé à chocs. .....................21

Symboles ..................................................22-25

Apprenez à connaître votre clé à chocs. ............................26

Caractéristiques techniques .....................................26

Mode d’emploi ..............................................27-31

Entretien ......................................................32

Dépannage ....................................................33

Garantie limitée de l’outil sans l SKIL ..........................34-35

AVERTISSEMENT

•

La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres

activités liées à la construction peut contenir des produits chimiques reconnus par l’État

de la Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

Plomb provenant de peintures à base de plomb.

–

Silice cristalline provenant de la brique, du ciment ou d’autres matériaux de maçonnerie.

–

Arsenic et chrome contenus dans le bois d’œuvre traité avec des produits chimiques.

•

Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

Travaillez dans un endroit bien ventilé.

–

Munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques.

–

Évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le

polissage, le perçage et d’autres activités liées à la construction. Portez un équipement de

protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant

dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent

causer l’absorption de produits chimiques dangereux.

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX RELATIFS

AUX OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lisez tous les avertissements et toutes les instructions,

illustrations et spécications fournis avec cet outil

électrique. Le non-respect des consignes de sécurité ci-dessous peut occasionner un choc

électrique, un incendie ou des blessures graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES

INSTRUCTIONS AFIN DE POUVOIR LES CONSULTER RÉFÉRER

ULTÉRIEUREMENT.

L’expression « outil électrique » utilisée dans les avertissements correspond aux outils

électriques alimentés sur secteur (à l) ou alimentés par piles (sans l).

Mesures de sécurité dans l’aire de travail

Maintenez l’aire de travail propre et bien éclairée. Les aires de travail sombres et

encombrées sont propices aux accidents.

N’utilisez pas d’outils électriques dans un endroit présentant un risque d’explosion,

par exemple en présence de liquides, de gaz ou de poussières inammables. Les outils

électriques produisent des étincelles pouvant causer un incendie en raison de la poussière et

des fumées.

Gardez les enfants et les autres personnes à l’écart lorsque vous utilisez un outil

électrique. Une distraction peut vous faire perdre la maîtrise de l’outil.

Consignes de sécurité relatives à l’électricité

Les ches des outils électriques doivent correspondre à la prise. Ne modiez jamais la

che de quelque façon que ce soit. N’utilisez pas d’adaptateur avec les outils électriques

mis à la terre. L’utilisation de ches non modiées dans les prises compatibles réduit les

risques de choc électrique.

Évitez de toucher à des surfaces mises à la terre, par exemple, un tuyau, un radiateur,

une cuisinière ou un réfrigérateur. Le contact du corps avec une surface mise à la terre

augmente les risques de choc électrique.

N’exposez pas les outils électriques à la pluie ni à tout environnement humide.

L’inltration d’eau dans un outil électrique augmente les risques de décharge électrique.

N’utilisez pas le cordon d’alimentation de façon à l’endommager. Ne transportez jamais

un outil électrique en le tenant par son cordon, et ne tirez jamais sur le cordon pour le

débrancher. Tenez le cordon d’alimentation éloigné des sources de chaleur, de l’huile,

des objets coupants et des pièces mobiles. Les risques de choc électrique sont plus

élevés si le cordon d’alimentation est endommagé ou emmêlé.

Lorsque vous utilisez un outil électrique à l’extérieur, utilisez une rallonge conçue pour

être utilisée à l’extérieur. Ce type de rallonge réduit les risques de choc électrique.

Si vous n’avez d’autre choix que d’utiliser un outil électrique dans un endroit humide,

utilisez une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un

disjoncteur différentiel réduit les risques de choc électrique.

Sécurité personnelle

Soyez vigilant, prêtez attention à ce que vous faites et usez de votre jugement lorsque

vous utilisez un outil électrique. N’utilisez pas un outil électrique lorsque vous êtes

fatigué ou sous l’effet de drogues, d’alcool ou de médicaments. Un moment d’inattention

lorsque vous utilisez des outils électriques peut occasionner des blessures graves.

Utilisez un équipement de protection. Portez toujours des lunettes de sécurité. Le

port d’un équipement de protection (comme un masque antipoussières, des chaussures de

protection antidérapantes, un casque de sécurité ou un dispositif de protection auriculaire),

lorsque les conditions l’exigent, réduit les risques de blessures.

Prenez des mesures an d’éviter que l’outil se mette en marche accidentellement.

Veillez à ce que l’interrupteur soit en position d’arrêt avant de connecter le produit

au courant ou au bloc-piles, de le ramasser ou de le transporter. Transporter les outils

électriques avec le doigt sur la gâchette ou brancher les outils lorsque l’interrupteur est à la

position de marche augmente les risques d’accident.

Enlevez toute clé de serrage ou clé à molette avant de mettre l’outil électrique

en marche. Une clé de réglage oubliée sur une pièce rotative de l’outil électrique peut

occasionner des blessures graves.

Ne tendez pas les bras trop loin. Gardez une posture sécuritaire et un bon équilibre

en tout temps. Cela vous permet de mieux maîtriser l’outil électrique lorsque des situations

inattendues se présentent.

Habillez-vous convenablement. Ne portez pas de vêtements amples ni de bijoux.

Gardez vos cheveux, vos vêtements et vos gants loin des pièces mobiles. Les vêtements

amples, les bijoux ou les cheveux longs risquent de se prendre dans les pièces mobiles.

Si des dispositifs sont fournis pour le branchement d’équipement de dépoussiérage

et de collecte de la poussière, veillez à ce qu’ils soient branchés et utilisés de manière

appropriée. L’emploi d’un dépoussiéreur contribue à réduire les dangers liés à la poussière.

Même si vous connaissez parfaitement ces outils parce que vous les utilisez souvent,

soyez vigilant et respectez les principes de sécurité. Il suft d’être négligent une fraction

de seconde pour se blesser gravement.

Utilisation et entretien d’un outil électrique

Ne forcez pas l’outil électrique. Utilisez l’outil électrique approprié à la tâche que vous

souhaitez accomplir. L’outil électrique adéquat vous permettra de mieux accomplir le travail

avec plus de sécurité et au rythme pour lequel il a été conçu.

N’utilisez pas l’outil électrique si l’interrupteur ne permet pas de le mettre en marche et

de l’arrêter. Tout outil électrique qui ne peut être commandé au moyen de l’interrupteur est

dangereux et doit être réparé.

Débranchez la che de la source d’alimentation ou retirez, si possible, le bloc-

piles de l’outil électrique avant de le ranger ou de procéder à un ajustement ou à un

changement d’accessoire. Ces mesures de sécurité préventives réduisent les risques de

mettre accidentellement l’outil électrique en marche.

Rangez l’outil électrique à l’arrêt hors de la portée des enfants et n’autorisez pas une

personne ne sachant pas s’en servir ou n’ayant pas lu ces instructions à l’utiliser.

Les outils électriques sont dangereux s’ils se retrouvent entre les mains d’utilisateurs qui ne

savent pas s’en servir.

Entretenez les outils électriques et les accessoires. Vériez les pièces mobiles pour

vous assurer qu’elles ne sont pas désalignées, enrayées, brisées, ou dans un état qui

pourrait nuire à leur fonctionnement. Si l’outil électrique est endommagé, faites-le réparer

avant de l’utiliser. De nombreux accidents sont provoqués par des outils électriques mal

entretenus.

Gardez vos outils tranchants affûtés et propres. Des outils de découpe aux lames affûtées

risquent moins de s’accrocher et sont plus faciles à contrôler.

Utilisez l’outil électrique, les accessoires, les mèches, etc. conformément à ces

instructions, en tenant compte des conditions de travail et de la tâche à accomplir.

L’utilisation de l’outil électrique à des ns autres que celles pour lesquelles il a été conçu

pourrait créer une situation dangereuse.

La page charge ...

Skil ID572701 Le manuel du propriétaire

Marque: Skil

Modèle: ID572701

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

ID572702

Télécharger le PDF

rapport

dans d''autres langues

English: Skil ID572701 Owner's manual

Skil ID572701 Le manuel du propriétaire

Ce manuel convient également à

Skil ID572701 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents