Toro eTimeMaster 76cm 60V Lawn Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

Form No. 3461-721 Rev A
eT imeMaster™ eTM76 76cm 60V Lawn Mower
21876 , 21876T
eT imeMaster™ eTM76 76 cm 60 V -Rasenmäher
21876 , 21876T
Cortacésped eT imeMaster™ eTM76 60 V de 76 cm
21876 , 21876T
T ondeuse eT imeMaster™ eTM76 de 76 cm et 60 V
21876 , 21876T
eT imeMaster™ eTM76 76 cm 60 V gazonmaaier
21876 , 21876T
www .T oro.com.
*3461-721*
Form No. 3461-709 Rev A
eT imeMaster ™ eTM76 76cm 60V
Lawn Mower
Model No. 21876 —Serial No. 400000000 and Up
Model No. 21876T —Serial No. 400000000 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3461-709*
This product complies with all relevant European
directives; for details, please see the separate product
specic Declaration of Conformity (DOC) sheet.
For assistance, please see
www .T oro.com/support
for instructional videos or
contact your Authorized
Service Dealer before
returning this product.
Do not tamper with or disable safety devices on the
machine, and check their proper operation regularly .
Do not attempt to adjust or tamper with the engine
speed control; doing so may create an unsafe
operating condition, resulting in personal injury .
Introduction
This rotary-blade, walk-behind lawn mower is intended
to be used by residential homeowners. It is designed
primarily for cutting grass on well-maintained lawns
on residential properties. It is not designed for cutting
brush or for agricultural uses. It is designed to use
T oro 60V lithium-ion battery packs. These battery
packs are designed to be charged only by T oro 60V
lithium-ion battery chargers. Using these products for
purposes other than their intended use could prove
dangerous to you and bystanders.
Model 21876T does not include a battery or a
charger .
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for more information, including
safety tips, training materials, accessory information,
help nding a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Dealer or T oro Customer Service and have the model
and serial numbers of your product ready . Figure 1
identies the location of the model and serial numbers
on the product. W rite the numbers in the space
provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information.
g428069
Figure 1
1. Model and serial number location
Model No.
Serial No.
Safety-Alert Symbol
The safety-alert symbol ( Figure 2 ) shown in this
manual and on the machine identies important safety
messages that you must follow to prevent accidents.
g000502
Figure 2
Safety-alert symbol
The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word DANGER ,W ARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury .
W ARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury .
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury .
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes general
information worthy of special attention.
Contents
Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety ....................................................................... 3
........................................................................... 3
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setup ........................................................................ 8
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in Mexico
All Rights Reserved
1 Assembling and Unfolding the Handle . . . . . . . . . . . . . . 8
2 Installing the Blade-Control Bar . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Assembling the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Mounting the Battery Charger
(Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Adjusting the Handle Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Starting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the Blade Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Shutting Of f the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Recycling the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bagging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Side-Discharging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removing the Battery Pack from the
Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning Under the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Folding the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Recommended Maintenance Schedule(s) . . . . . . . . . . . 20
Lubricating the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . 20
Servicing the Blade-Drive System . . . . . . . . . . . . . . . . . . . . . 20
Servicing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Checking for Bent Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Preparing the Battery Pack for
Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Safety
IMPORT ANT SAFETY
INSTRUCTIONS
W ARNING
When using electric lawn mowers, basic
safety precautions should always be followed
to reduce the risk of re, electric shock, and
personal injury , including the following:
Read All Instructions
I. T raining
1. The operator of the machine is responsible for
any accidents or hazards occurring to others or
their property .
2. Do not allow children to use or play with the
machine, battery pack, or the battery charger;
local regulations may restrict the age of the
operator .
3. Do not allow children or untrained people to
operate or service this device. Allow only people
who are responsible, trained, familiar with the
instructions, and physically capable to operate
or service the device.
4. Before using the machine, battery pack, and
battery charger , read all the instructions and
cautionary markings on these products.
5. Become familiar with the controls and proper
use of the machine, battery pack, and battery
charger .
II. Preparation
1. Keep bystanders, especially children and pets,
out of the operating area.
2. Do not operate the machine without all guards
and safety devices, such as deectors and grass
catchers, in place and functioning properly on
the machine.
3. Inspect the area where you will use the machine
and remove all objects that could interfere with
the operation of the machine or that the machine
could throw .
4. Before using the machine, ensure that the blade,
blade bolt, and blade assembly are not worn or
damaged. Replace any damaged or unreadable
labels.
5. Use only the battery pack specied by T oro.
Using other accessories and attachments may
increase the risk of injury and re.
6. Plugging the battery charger into an outlet that
is not 100 to 240V can cause a re or electric
3
shock. Do not plug the battery charger into an
outlet other than 100 to 240V . For a dif ferent
style of connection, use an attachment plug
adapter of the proper conguration for the power
outlet if needed.
7. Do not use a damaged or modied battery
pack or battery charger , which may exhibit
unpredictable behavior that results in re,
explosion, or risk of injury .
8. If the supply cord to the battery charger is
damaged, contact an Authorized Service Dealer
to replace it.
9. Charge the battery pack with only the battery
charger specied by T oro. A charger suitable for
1 type of battery pack may create a risk of re
when used with another battery pack.
10. Charge the battery pack in a well-ventilated area
only .
1 1. Follow all charging instructions and do
not charge the battery pack outside of the
temperature range specied in the instructions.
Otherwise, you may damage the battery pack
and increase the risk of re.
12. Dress properly—W ear appropriate clothing,
including eye protection; long pants; substantial,
slip-resistant footwear (not barefoot or wearing
sandals); and hearing protection. T ie back long
hair and do not wear loose clothing or loose
jewelry that can get caught in moving parts.
W ear a dust mask in dusty operating conditions.
III. Operation
1. Contact with the moving blade will cause serious
injury . Keep your hands and feet away from the
cutting area and all moving parts of the machine.
Keep clear of any discharge opening.
2. Using this machine for purposes other than its
intended use could prove dangerous to you and
bystanders.
3. Disengage the self-propel drive (if equipped)
before starting the machine.
4. Do not tilt the machine when starting the motor .
5. Prevent unintentional starting—Ensure that
the electric-start button is removed from the
electric-start switch before connecting the
battery pack and handling the machine.
6. Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
7. Stop the machine, remove the electric-start
button, remove the battery pack from the
machine, and wait for all movement to stop
before adjusting, servicing, cleaning, or storing
the machine.
8. Remove the battery pack and electric-start
button from the machine whenever you leave it
unattended or before changing accessories.
9. Do not force the machine—Allow the machine to
do the job better and safer at the rate for which it
was designed.
10. Stay alert—W atch what you are doing and use
common sense when operating the machine.
Do not use the machine while ill, tired, or under
the inuence of alcohol or drugs.
1 1. Do not use a battery-operated lawn mower in
rain.
12. Operate the machine only in good visibility and
appropriate weather conditions. Do not operate
the machine when there is the risk of lightning.
13. Use extreme caution when reversing or pulling
the machine toward you.
14. Keep proper footing and balance at all times,
especially on slopes. Mow across the face
of slopes, never up and down. Use extreme
caution when changing directions on slopes. Do
not mow exceedingly steep slopes. W alk, never
run with the machine.
15. Do not direct the discharge material toward
anyone. A void discharging material against a
wall or obstruction; material may ricochet toward
you. Stop the blade(s) when crossing surfaces
other than grass.
16. W atch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could cause you
to lose your balance or footing.
17. W et grass or leaves can cause serious injury if
you slip and contact the blade. Do not mow in
wet conditions. Do not mow when it is raining.
18. If the machine strikes an object or starts to
vibrate, immediately shut of f the machine,
remove the electric-start button, remove the
battery pack, and wait for all movement to stop
before examining the machine for damage.
Make all necessary repairs before resuming
operation.
19. Stop the machine and remove the electric-start
button before loading the machine for hauling.
20. Under abusive conditions, the battery pack may
eject liquid; avoid contact. If you accidently
come into contact with the liquid, ush with
water . If the liquid contacts your eyes, seek
medical help. Liquid ejected from the battery
pack may cause irritation or burns.
4
IV . Maintenance and Storage
1. Stop the machine, remove the electric-start
button, remove the battery pack from the
machine, and wait for all movement to stop
before adjusting, servicing, cleaning, or storing
the machine.
2. Do not attempt to repair the machine except as
indicated in the instructions. Have an Authorized
Service Dealer perform service on the machine
using identical replacement parts.
3. W ear gloves and eye protection when servicing
the machine.
4. Sharpen a dull blade on both edges to maintain
balance. Clean the blade and ensure that it is
balanced.
5. Replace the blade if it is bent, worn, or cracked.
An unbalanced blade causes vibration, which
could damage the motor or cause personal
injury .
6. When servicing the blade, be aware that the
blade can still move even though the power
source is of f.
7. Check the grass collection bag frequently for
deterioration or wear , and replace a worn bag
with a T oro [replacement] bag.
8. For best performance, use only genuine T oro
replacement parts and accessories. Other
replacement parts and accessories could be
dangerous, and such use could void the product
warranty .
9. Maintain the machine—Keep cutting edges
sharp and clean for the best and safest
performance. Keep handles dry , clean, and free
from oil and grease. Keep guards in place and in
working order . Keep blades sharp. Use identical
replacement blades only .
10. Check the machine for damaged parts—If there
are damaged guards or other parts, determine
whether the machine will operate properly .
Check for misaligned and binding moving parts,
broken parts, mounting, and any other condition
that may af fect its operation. Unless indicated
in the instructions, have an Authorized Service
Dealer repair or replace a damaged guard or
part.
1 1. When the battery pack is not in use, keep it
away from metal objects such as paper clips,
coins, keys, nails, and screws that can make a
connection from 1 terminal to another . Shorting
the battery terminals may cause burns or a re.
12. Check the blade and motor mounting bolts
frequently for tightness.
13. When you are not using the machine, store it
indoors in a dry , secure place out of the reach
of children.
14. Do not expose a battery pack or machine to re
or excessive temperature. Exposure to re or
temperature above 130°C (265°F) may cause
explosion.
15. CAUTION—A mistreated battery pack may
present a risk of re, explosion, or chemical
burn.
Do not disassemble the battery pack.
Replace the battery pack with a genuine
T oro battery pack only; using another type of
battery pack may cause a re or risk of injury .
Keep battery packs out of the reach of
children and in the original packaging until
you are ready to use them.
SA VE THESE
INSTRUCTIONS
5
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal1 12-8760
1 12-8760
1. Thrown object hazard—keep bystanders away .
2. Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.
decal120-9570
120-9570
1. W arning—stay away from moving parts, keep all guards
and shields in place.
decal134-4691
134-4691
1. Auto speed 2. Max speed
decal145-1454
145-1454
1. W arning—read the
Operator ’ s Manual .
4. Thrown object
hazard—keep bystanders
away; shut of f the machine
and wait for all moving
parts to stop before
leaving the machine; pick
up debris before mowing.
2. Cutting/dismemberment
hazard of the hand, mower
blade—stay away from
moving parts; keep all
guards and shields in
place.
5. Cutting/dismemberment
hazard of the foot, mower
blade—do not mow up
or down slopes; only
mow across slopes; look
behind you when mowing
in reverse.
3. Cutting/dismemberment
hazard of the hand, mower
blade—remove the key
and read the Operator ’ s
Manual before performing
maintenance.
6
Model 81805
decal144-6035
144-6035
1. Do not dispose improperly 3. For indoor use
2. Read the Operator ’ s Manual .
4. Double insulated
decal145-3129
145-3129
1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature
range.
2. The battery pack is fully charged. 4. Battery pack charging fault
Model 68810
decal145-8263
145-8263
1. Read the Operator ’ s
Manual .
4. Keep away from open re
or ames
2. Recycle the battery 5. Do not expose to rain
3. Do not dispose improperly
decal145-8265
145-8265
1. Battery charge status
7
Setup
Important: The battery pack is not fully charged when it is purchased. Before using the machine for
the rst time, refer to Charging the Battery Pack ( page 17 ) .
Important: Remove and discard the protective plastic sheet that covers the motor and any other
plastic or wrapping on the machine.
1
Assembling and Unfolding the Handle
No Parts Required
Procedure
W ARNING
Folding or unfolding the handle improperly can damage the cables, causing an unsafe
operating condition.
• Do not damage the cable(s) when folding or unfolding the handle.
Ensure that the cable(s) are routed to the outside of the handle.
If a cable is damaged, contact an Authorized Service Dealer .
g426198
Figure 3
8
2
Installing the Blade-Control
Bar
No Parts Required
Procedure
g344378
Figure 4
3
Assembling the Grass Bag
No Parts Required
Procedure
g230447
Figure 5
4
Mounting the Battery
Charger (Optional)
Parts needed for this procedure:
2
Mounting hardware (not included)
Procedure
If desired, mount the battery charger securely on a
wall using the wall-mount key holes on the back of
the charger .
Mount it indoors (such as a garage or other dry place),
near a power outlet, and out of the reach of children.
Refer to Figure 6 for assistance in mounting the
charger .
Slide the charger over the appropriately positioned
hardware to secure the charger in place (hardware
not included).
g290534
Figure 6
9
Product Overview
g434444
Figure 7
1. Side-discharge deector
8. T raction-assist handle
2. Headlight 9. Electric-start button
3. Battery compartment
10. Rear deector
4. Handle-lock lever 1 1. Rear cutting-height lever
5. Handle knob (2)
12. W ashout port
6. Blade-control bar 13. Front cutting-height lever
7. Personal pace handle
g410592
Figure 8
1. Grass bag 3. Side-discharge chute
2. Rear-discharge plug
(installed)
g426502
Figure 9
1. Battery charger Model
81805 (included with
Model 21876)
2. Battery pack Model 68810
(2 included with Model
21876)
Specications
Model
Model W eight Length W idth Height
21876 and
21876T
59.4 kg
(131 lb)
165
cm (65
inches)
81 cm (32
inches)
1 14
cm (45
inches)
Battery Pack
Model 68810
10.0 AhBattery pack capacity
540 Wh
Battery manufacturer rating = 60V maximum and 54V nominal.
Actual voltage varies with load.
Battery Charger
Model 81805
T ype 60V MAX Lithium-Ion Battery
Rapid Charger
Input
100 to 240V AC ~5.0A, 50/60Hz
Output 60V DC 5.5A MAX
Appropriate T emperature Ranges
Charge battery pack at 5°C (41°F) to 40°C (104°F)*
Use battery pack at
-30°C (-22°F) to 49°C (120°F)
Store battery pack/charger at 5°C (41°F) to 40°C (104°F)*
*Charging time will increase if you do not charge the
battery within this range.
Store the tool, battery pack, and battery charger in an
enclosed clean, dry area.
10
Attachments/Accessories
A selection of T oro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or authorized T oro distributor or go to
www .T oro.com for a list of all approved attachments and accessories.
T o ensure optimum performance and continued safety certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be
dangerous, and such use could void the product warranty .
Operation
Note: Determine the left and right sides of the machine from the normal operating position.
Before Operation
Installing the Battery Pack
Important: Use the battery pack only in temperatures that are within the appropriate range; refer
to Specications ( page 10 ) .
1. Make sure that the vents on the battery are clear of any dust and debris.
2. Lift up the battery-compartment lid (A of Figure 10 ).
3. Line up the cavity in the battery pack with the tongue on the machine and slide the battery pack into the
compartment until it locks into place (B of Figure 10 ).
4. Close the battery-compartment lid (C of Figure 10 ).
Note: If the battery-compartment lid does not close completely , the battery is not fully installed.
g410618
Figure 10
1 1
Adjusting the Handle Height
Y ou may raise or lower the handle to a position comfortable for you.
Pull the handle-lock lever rearward to disengage the handle-lock pins, move the handle to 1 of 4 positions, and
release the handle-lock lever to secure the handle in place ( Figure 1 1 ).
g426209
Figure 1 1
Adjusting the Cutting Height
DANGER
Adjusting the height of cut could bring your hands into contact with a moving blade and
result in serious injury .
Shut off the motor , remove the battery , and wait for all moving parts to stop before adjusting
the cutting height.
Do not put your ngers under the housing when adjusting the cutting height.
Note: T o raise the machine, move the front and rear cutting-height levers forward; to lower the machine,
move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances
require otherwise.
g426213
Figure 12
12
During Operation
Starting the Machine1. Ensure that the battery pack(s) are installed in the machine; refer to Installing the Battery Pack ( page 1 1 ) .
2. Insert the electric-start button into the electric-start switch (A of Figure 13 ).
3. Squeeze the blade-control bar and hold it to the handle for 2 seconds (B of Figure 13 ).
4. Press the electric-start button and keep it pressed until the motor starts (C of Figure 13 ).
g426674
Figure 13
Adjusting the Blade Speed
This machine has 2 blade-speed settings: A UTO and
MAX .
When set to the A UTO position, the blade speed
is adjusted automatically for greater ef ciency;
changes in cutting conditions are detected and
the blade speed increases when necessary to
maintain quality of cut.
When set to the M AX position, the blade speed
remains at the highest speed at all times. The
traction speed of the machine also increases.
T urn the electric-start button in the electric-start switch
to either position to adjust the blade speed setting
(Figure 14 ).
g337279
Figure 14
1. A UTO position 2. M AX position
Using the Self-Propel Drive
T o operate the self-propel drive, simply walk with your
hands on the upper handle and your elbows at your
sides, and the machine will automatically keep pace
with you ( Figure 15 ).
Note: Use the traction-assist handle in situations
when you need more control than you have with the
self-propel drive alone.
g434445
Figure 15
Note: If the machine does not freely roll backward
after self-propelling, stop walking, hold your hands
in place, and allow the machine to roll a couple of
centimeters (inches) forward to disengage the wheel
drive. Y ou can also try reaching just under the upper
handle to the metal handle and pushing the machine
forward a couple of centimeters (inches). If the
machine still does not roll backward easily , contact an
Authorized Service Dealer .
13
Shutting Off the Machine
1. Release the blade-control bar (A of Figure 16 ).
2. Remove the electric-start button from the
electric-start switch (B of Figure 16 ).
3. Remove the battery pack; refer to Removing the
Battery Pack from the Machine ( page 17 ) .
Note: Whenever you are not using the machine,
remove the battery pack.
g335480
Figure 16
Recycling the Clippings
This machine comes from the factory ready to recycle
grass and leaf clippings back into the lawn. T o prepare
the machine to recycle, do the following:
If the side-discharge chute is on the machine,
remove it and lower the side-discharge deector;
refer to Removing the Side-Discharge Chute
( page 15 ) .
If the grass bag is on the machine, remove it; refer
to Removing the Grass Bag ( page 15 ) .
If the rear-discharge plug is not installed, grip it by
the handle, raise the rear deector , and insert it
into the rear-discharge chute until the latch locks
into place; refer to Figure 17 .
g426214
Figure 17
Bagging the Clippings
Use the grass bag when you want to collect grass and leaf clippings from the lawn.
If the side-discharge chute is on the mower , remove it before bagging the clippings; refer to Removing the
Side-Discharge Chute ( page 15 ) .
Installing the Grass Bag
1. Raise and hold up the rear deector (A of Figure 18 ).
2. Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out
from the machine (B of Figure 18 ).
3. Install the bag rod into the notches at the base of the handle and rock the bag back and forth to ensure
that the rod is seated at the bottom of both notches (C of Figure 18 ).
4. Lower the rear deector until it rests on the grass bag.
14
g426289
Figure 18
Removing the Grass Bag
DANGER
The machine can throw grass clippings and other objects through an opening in the machine
housing. Objects thrown with enough force could cause serious personal injury or death to
you or to bystanders.
Never remove the grass bag and then start the machine without the discharge plug installed
on the machine.
• Never open the rear deector on the machine when the machine is running.
T o remove the bag, reverse the steps in Installing the Grass Bag ( page 14 ) .
Side-Discharging the
Clippings
Use the side discharge for cutting very tall grass.
If the bag is on the machine, remove it and insert the
rear-discharge plug; refer to Removing the Grass Bag
( page 15 ) before side-discharging the clippings.
Important: Ensure that the rear-discharge plug is
in place before you recycle the clippings ( Figure
17 ).
Installing the Side-Discharge
Chute
1. Remove the side-discharge deector bracket
and fasteners (A of Figure 19 ).
2. Unlatch and lift up the side deector and install
the side-discharge chute (B, C, and D of Figure
19 ).
g456257
Figure 19
1. Locknut
3. Deector bracket
2. Bolt
Removing the Side-Discharge
Chute
T o remove the side-discharge chute, lift up the side
deector , remove the side-discharge chute, and lower
the side-discharge deector until it latches securely .
15
Important: Install the deector bracket when not
using the side-discharge chute (A of Figure 19 ).
Operating T ips
General Mowing T ips
Inspect the area where you will use the machine
and remove all objects that the machine could
throw .
A void striking solid objects with the blades. Never
deliberately mow over any object.
If the machine strikes an object or starts to vibrate,
immediately shut of f the machine, wait for all
moving parts to stop, remove the battery pack
from the machine, and examine the machine for
damage.
For best performance, install new T oro blades
before the cutting season begins or when
necessary .
Cutting Grass
Cut only about a third of the grass blade at a time.
For improved quality of cut, runtime, and bagging,
cut grass at a higher height of cut.
Do not cut below 51 mm (2 inches) unless the
grass is sparse or it is late fall when grass growth
begins to slow down.
When cutting grass over 15 cm (6 inches) tall,
mow at the highest cutting height setting and walk
slower; then mow again at a lower setting for the
best lawn appearance. If the grass is too long, the
machine may plug and cause the motor to stall.
W et grass and leaves tend to clump on the yard
and can cause the machine to plug or the motor to
stall. A void mowing in wet conditions.
Be aware of a potential re hazard in very dry
conditions, follow all local re warnings, and keep
the machine free of dry grass and leaf debris.
Alternate the mowing direction. This helps
disperse the clippings over the lawn for even
fertilization.
If the nished lawn appearance is unsatisfactory ,
try 1 or more of the following:
– Replace the blades or have them sharpened.
W alk at a slower pace while mowing.
– Raise the cutting height on your machine.
– Cut the grass more frequently .
Overlap cutting swaths instead of cutting a full
swath with each pass.
Cutting Leaves
After cutting the lawn, ensure that half of the lawn
shows through the cut leaf cover . Y ou may need
to make more than a single pass over the leaves.
If there are more than 13 cm (5 inches) of leaves
on the lawn, mow at a higher cutting height and
then again at the desired cutting height.
Slow down your mowing speed if the machine
does not cut the leaves nely enough.
16
After Operation
Removing the Battery Pack
from the Machine
1. Lift up the battery-compartment lid.
2. Press the battery-pack latch to release the
battery pack and remove the battery pack.
3. Close the battery-compartment lid.
Charging the Battery Pack
Important: The battery pack is not fully charged
when you purchase it. Before using the tool for
the rst time, place the battery pack in the charger
and charge it until the LED display indicates the
battery pack is fully charged. Read all safety
precautions.
Important: Charge the battery pack only in
temperatures that are within the appropriate
range; refer to Specications ( page 10 ) .
Note: At any time, press the battery-charge-indicator
button on the battery pack to display the current
charge (LED indicators).
1. Ensure that the vents on the battery and charger
are clear of any dust and debris.
g290533
Figure 20
1. Battery pack cavity
5. LED indicators (current
charge)
2. Battery pack venting areas 6. Handle
3. Battery pack terminals
7. Charger LED indicator
light
4. Battery-charge-indicator
button
8. Charger venting areas
2. Line up the cavity in the battery pack ( Figure 20 )
with the tongue on the charger .
3. Slide the battery pack into the charger until it is
fully seated ( Figure 20 ).
4. T o remove the battery pack, slide the battery
backward out of the charger .
5. Refer to the following table to interpret the LED
indicator light on the battery charger .
Indicator
light
Indicates
Of f
No battery pack inserted
Green
blinking
Battery pack is charging
Green
Battery pack is charged
Red
Battery pack and/or battery charger is over or under
the appropriate temperature range
Red
blinking
Battery pack charging fault*
*Refer to T roubleshooting ( page 25 ) for more
information.
Important: The battery can be left on the charger
for short periods between uses.
If the battery will not be used for longer periods,
remove the battery from the charger; refer to
Storage ( page 24 ) .
Cleaning Under the
Machine
Service Interval : After each use
W ARNING
A broken or missing washout tting could
expose you and others to thrown objects or
blade contact. Contact with a blade or thrown
debris can cause injury or death.
Replace a broken or missing washout
tting immediately , before using the
machine again.
• Never put your hands or feet under the
machine or through openings in the
machine.
1. Move the machine to a level surface.
2. Shut of f the machine and wait for all moving
parts to stop before leaving the operating
position.
3. Lower the machine to its lowest cutting-height
setting. Refer to Adjusting the Cutting Height
( page 12 ) .
17
4. Attach a hose to the washout tting, and turn the
water on high ( Figure 21 ).
Note: Spread petroleum jelly on the washout
tting O-ring to make the coupling slide on
easier and protect the O-ring.
g003934
Figure 21
1. W ashout tting 3. O-ring
2. Hose
4. Coupling
5. Start the machine, engage the blade-control
lever , and let the machine run for 1 to 3 minutes
with the blades turning.
6. Disengage the blade-control lever , shut of f the
machine, and wait for all moving parts to stop.
7. Shut of f the water and remove the coupling from
the washout tting.
Note: If the machine is not clean after a single
washing, soak it and let it stand for 30 minutes.
Then repeat the process.
8. Run the machine again and engage the blades
for 1 to 3 minutes to remove the excess water .
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144

Toro eTimeMaster 76cm 60V Lawn Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à