Toro eTimeMaster eTM76 76cm 60V Lawn Mower Manuel utilisateur

Form No. 3461-721 Rev A

eT imeMaster™ eTM76 76cm 60V Lawn Mower

21876 , 21876T

eT imeMaster™ eTM76 76 cm 60 V -Rasenmäher

21876 , 21876T

Cortacésped eT imeMaster™ eTM76 60 V de 76 cm

21876 , 21876T

T ondeuse eT imeMaster™ eTM76 de 76 cm et 60 V

21876 , 21876T

eT imeMaster™ eTM76 76 cm 60 V gazonmaaier

21876 , 21876T

www .T oro.com.

*3461-721*

Form No. 3461-709 Rev A

eT imeMaster ™ eTM76 76cm 60V

Lawn Mower

Model No. 21876 —Serial No. 400000000 and Up

Model No. 21876T —Serial No. 400000000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3461-709*

This product complies with all relevant European

directives; for details, please see the separate product

specic Declaration of Conformity (DOC) sheet.

For assistance, please see

www .T oro.com/support

for instructional videos or

contact your Authorized

Service Dealer before

returning this product.

Do not tamper with or disable safety devices on the

machine, and check their proper operation regularly .

Do not attempt to adjust or tamper with the engine

speed control; doing so may create an unsafe

operating condition, resulting in personal injury .

Introduction

This rotary-blade, walk-behind lawn mower is intended

to be used by residential homeowners. It is designed

primarily for cutting grass on well-maintained lawns

on residential properties. It is not designed for cutting

brush or for agricultural uses. It is designed to use

T oro 60V lithium-ion battery packs. These battery

packs are designed to be charged only by T oro 60V

lithium-ion battery chargers. Using these products for

purposes other than their intended use could prove

dangerous to you and bystanders.

Model 21876T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g428069

Figure 1

1. Model and serial number location

Model No.

Serial No.

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Contents

Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety ....................................................................... 3

........................................................................... 3

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup ........................................................................ 8

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in Mexico

1 Assembling and Unfolding the Handle . . . . . . . . . . . . . . 8

2 Installing the Blade-Control Bar . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Assembling the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Mounting the Battery Charger

(Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Adjusting the Handle Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adjusting the Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Starting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjusting the Blade Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Using the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Shutting Of f the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Recycling the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Bagging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Side-Discharging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Removing the Battery Pack from the

Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cleaning Under the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Folding the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Recommended Maintenance Schedule(s) . . . . . . . . . . . 20

Lubricating the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Adjusting the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . 20

Servicing the Blade-Drive System . . . . . . . . . . . . . . . . . . . . . 20

Servicing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Checking for Bent Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Removing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Preparing the Battery Pack for

Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using electric lawn mowers, basic

safety precautions should always be followed

to reduce the risk of re, electric shock, and

personal injury , including the following:

Read All Instructions

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

3. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

4. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

5. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders, especially children and pets,

out of the operating area.

2. Do not operate the machine without all guards

and safety devices, such as deectors and grass

catchers, in place and functioning properly on

the machine.

3. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

4. Before using the machine, ensure that the blade,

blade bolt, and blade assembly are not worn or

damaged. Replace any damaged or unreadable

labels.

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet that

is not 100 to 240V can cause a re or electric

3

shock. Do not plug the battery charger into an

outlet other than 100 to 240V . For a dif ferent

style of connection, use an attachment plug

adapter of the proper conguration for the power

outlet if needed.

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant footwear (not barefoot or wearing

sandals); and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry that can get caught in moving parts.

W ear a dust mask in dusty operating conditions.

III. Operation

1. Contact with the moving blade will cause serious

injury . Keep your hands and feet away from the

cutting area and all moving parts of the machine.

Keep clear of any discharge opening.

2. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

3. Disengage the self-propel drive (if equipped)

before starting the machine.

4. Do not tilt the machine when starting the motor .

5. Prevent unintentional starting—Ensure that

the electric-start button is removed from the

electric-start switch before connecting the

battery pack and handling the machine.

6. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

7. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

8. Remove the battery pack and electric-start

button from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Do not use a battery-operated lawn mower in

rain.

12. Operate the machine only in good visibility and

appropriate weather conditions. Do not operate

the machine when there is the risk of lightning.

13. Use extreme caution when reversing or pulling

the machine toward you.

14. Keep proper footing and balance at all times,

especially on slopes. Mow across the face

of slopes, never up and down. Use extreme

caution when changing directions on slopes. Do

not mow exceedingly steep slopes. W alk, never

run with the machine.

15. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Stop the blade(s) when crossing surfaces

other than grass.

16. W atch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause you

to lose your balance or footing.

17. W et grass or leaves can cause serious injury if

you slip and contact the blade. Do not mow in

wet conditions. Do not mow when it is raining.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the electric-start button, remove the

battery pack, and wait for all movement to stop

before examining the machine for damage.

Make all necessary repairs before resuming

operation.

19. Stop the machine and remove the electric-start

button before loading the machine for hauling.

20. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

4

IV . Maintenance and Storage

1. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an Authorized

Service Dealer perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. Sharpen a dull blade on both edges to maintain

balance. Clean the blade and ensure that it is

balanced.

5. Replace the blade if it is bent, worn, or cracked.

An unbalanced blade causes vibration, which

could damage the motor or cause personal

injury .

6. When servicing the blade, be aware that the

blade can still move even though the power

source is of f.

7. Check the grass collection bag frequently for

deterioration or wear , and replace a worn bag

with a T oro [replacement] bag.

8. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

9. Maintain the machine—Keep cutting edges

sharp and clean for the best and safest

performance. Keep handles dry , clean, and free

from oil and grease. Keep guards in place and in

working order . Keep blades sharp. Use identical

replacement blades only .

10. Check the machine for damaged parts—If there

are damaged guards or other parts, determine

whether the machine will operate properly .

Check for misaligned and binding moving parts,

broken parts, mounting, and any other condition

that may af fect its operation. Unless indicated

in the instructions, have an Authorized Service

Dealer repair or replace a damaged guard or

part.

1 1. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

12. Check the blade and motor mounting bolts

frequently for tightness.

13. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

14. Do not expose a battery pack or machine to re

or excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

15. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal1 12-8760

1 12-8760

1. Thrown object hazard—keep bystanders away .

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

decal120-9570

120-9570

1. W arning—stay away from moving parts, keep all guards

and shields in place.

decal134-4691

134-4691

1. Auto speed 2. Max speed

decal145-1454

145-1454

1. W arning—read the

Operator ’ s Manual .

4. Thrown object

hazard—keep bystanders

away; shut of f the machine

and wait for all moving

parts to stop before

leaving the machine; pick

up debris before mowing.

2. Cutting/dismemberment

hazard of the hand, mower

blade—stay away from

moving parts; keep all

guards and shields in

place.

5. Cutting/dismemberment

hazard of the foot, mower

blade—do not mow up

or down slopes; only

mow across slopes; look

behind you when mowing

in reverse.

3. Cutting/dismemberment

hazard of the hand, mower

blade—remove the key

and read the Operator ’ s

Manual before performing

maintenance.

6

Model 81805

decal144-6035

144-6035

1. Do not dispose improperly 3. For indoor use

2. Read the Operator ’ s Manual .

4. Double insulated

decal145-3129

145-3129

1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature

range.

2. The battery pack is fully charged. 4. Battery pack charging fault

Model 68810

decal145-8263

145-8263

1. Read the Operator ’ s

Manual .

4. Keep away from open re

or ames

2. Recycle the battery 5. Do not expose to rain

3. Do not dispose improperly

decal145-8265

145-8265

1. Battery charge status

7

Setup

Important: The battery pack is not fully charged when it is purchased. Before using the machine for

the rst time, refer to Charging the Battery Pack ( page 17 ) .

Important: Remove and discard the protective plastic sheet that covers the motor and any other

plastic or wrapping on the machine.

1

Assembling and Unfolding the Handle

No Parts Required

Procedure

W ARNING

Folding or unfolding the handle improperly can damage the cables, causing an unsafe

operating condition.

• Do not damage the cable(s) when folding or unfolding the handle.

• Ensure that the cable(s) are routed to the outside of the handle.

• If a cable is damaged, contact an Authorized Service Dealer .

g426198

Figure 3

8

2

Installing the Blade-Control

Bar

No Parts Required

Procedure

g344378

Figure 4

3

Assembling the Grass Bag

No Parts Required

Procedure

g230447

Figure 5

4

Mounting the Battery

Charger (Optional)

Parts needed for this procedure:

2

Mounting hardware (not included)

Procedure

If desired, mount the battery charger securely on a

wall using the wall-mount key holes on the back of

the charger .

Mount it indoors (such as a garage or other dry place),

near a power outlet, and out of the reach of children.

Refer to Figure 6 for assistance in mounting the

charger .

Slide the charger over the appropriately positioned

hardware to secure the charger in place (hardware

not included).

g290534

Figure 6

9

Product Overview

g434444

Figure 7

1. Side-discharge deector

8. T raction-assist handle

2. Headlight 9. Electric-start button

3. Battery compartment

10. Rear deector

4. Handle-lock lever 1 1. Rear cutting-height lever

5. Handle knob (2)

12. W ashout port

6. Blade-control bar 13. Front cutting-height lever

7. Personal pace handle

g410592

Figure 8

1. Grass bag 3. Side-discharge chute

2. Rear-discharge plug

(installed)

g426502

Figure 9

1. Battery charger Model

81805 (included with

Model 21876)

2. Battery pack Model 68810

(2 included with Model

21876)

Specications

Model

Model W eight Length W idth Height

21876 and

21876T

59.4 kg

(131 lb)

165

cm (65

inches)

81 cm (32

inches)

1 14

cm (45

inches)

Battery Pack

Model 68810

10.0 AhBattery pack capacity

540 Wh

Battery manufacturer rating = 60V maximum and 54V nominal.

Actual voltage varies with load.

Battery Charger

Model 81805

T ype 60V MAX Lithium-Ion Battery

Rapid Charger

Input

100 to 240V AC ~5.0A, 50/60Hz

Output 60V DC 5.5A MAX

Appropriate T emperature Ranges

Charge battery pack at 5°C (41°F) to 40°C (104°F)*

Use battery pack at

-30°C (-22°F) to 49°C (120°F)

Store battery pack/charger at 5°C (41°F) to 40°C (104°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the tool, battery pack, and battery charger in an

enclosed clean, dry area.

10

Attachments/Accessories

A selection of T oro approved attachments and accessories is available for use with the machine to enhance

and expand its capabilities. Contact your Authorized Service Dealer or authorized T oro distributor or go to

www .T oro.com for a list of all approved attachments and accessories.

T o ensure optimum performance and continued safety certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be

dangerous, and such use could void the product warranty .

Operation

Note: Determine the left and right sides of the machine from the normal operating position.

Before Operation

Installing the Battery Pack

Important: Use the battery pack only in temperatures that are within the appropriate range; refer

to Specications ( page 10 ) .

1. Make sure that the vents on the battery are clear of any dust and debris.

2. Lift up the battery-compartment lid (A of Figure 10 ).

3. Line up the cavity in the battery pack with the tongue on the machine and slide the battery pack into the

compartment until it locks into place (B of Figure 10 ).

4. Close the battery-compartment lid (C of Figure 10 ).

Note: If the battery-compartment lid does not close completely , the battery is not fully installed.

g410618

Figure 10

1 1

Adjusting the Handle Height

Y ou may raise or lower the handle to a position comfortable for you.

Pull the handle-lock lever rearward to disengage the handle-lock pins, move the handle to 1 of 4 positions, and

release the handle-lock lever to secure the handle in place ( Figure 1 1 ).

g426209

Figure 1 1

Adjusting the Cutting Height

DANGER

Adjusting the height of cut could bring your hands into contact with a moving blade and

result in serious injury .

• Shut off the motor , remove the battery , and wait for all moving parts to stop before adjusting

the cutting height.

• Do not put your ngers under the housing when adjusting the cutting height.

Note: T o raise the machine, move the front and rear cutting-height levers forward; to lower the machine,

move the cutting-height levers rearward. Set all the wheels to the same height unless special circumstances

require otherwise.

g426213

Figure 12

12

During Operation

Starting the Machine1. Ensure that the battery pack(s) are installed in the machine; refer to Installing the Battery Pack ( page 1 1 ) .

2. Insert the electric-start button into the electric-start switch (A of Figure 13 ).

3. Squeeze the blade-control bar and hold it to the handle for 2 seconds (B of Figure 13 ).

4. Press the electric-start button and keep it pressed until the motor starts (C of Figure 13 ).

g426674

Figure 13

Adjusting the Blade Speed

This machine has 2 blade-speed settings: A UTO and

MAX .

•When set to the A UTO position, the blade speed

is adjusted automatically for greater ef ciency;

changes in cutting conditions are detected and

the blade speed increases when necessary to

maintain quality of cut.

•When set to the M AX position, the blade speed

remains at the highest speed at all times. The

traction speed of the machine also increases.

T urn the electric-start button in the electric-start switch

to either position to adjust the blade speed setting

(Figure 14 ).

g337279

Figure 14

1. A UTO position 2. M AX position

Using the Self-Propel Drive

T o operate the self-propel drive, simply walk with your

hands on the upper handle and your elbows at your

sides, and the machine will automatically keep pace

with you ( Figure 15 ).

Note: Use the traction-assist handle in situations

when you need more control than you have with the

self-propel drive alone.

g434445

Figure 15

Note: If the machine does not freely roll backward

after self-propelling, stop walking, hold your hands

in place, and allow the machine to roll a couple of

centimeters (inches) forward to disengage the wheel

drive. Y ou can also try reaching just under the upper

handle to the metal handle and pushing the machine

forward a couple of centimeters (inches). If the

machine still does not roll backward easily , contact an

Authorized Service Dealer .

13

Shutting Off the Machine

1. Release the blade-control bar (A of Figure 16 ).

2. Remove the electric-start button from the

electric-start switch (B of Figure 16 ).

3. Remove the battery pack; refer to Removing the

Battery Pack from the Machine ( page 17 ) .

Note: Whenever you are not using the machine,

remove the battery pack.

g335480

Figure 16

Recycling the Clippings

This machine comes from the factory ready to recycle

grass and leaf clippings back into the lawn. T o prepare

the machine to recycle, do the following:

•If the side-discharge chute is on the machine,

remove it and lower the side-discharge deector;

refer to Removing the Side-Discharge Chute

( page 15 ) .

•If the grass bag is on the machine, remove it; refer

to Removing the Grass Bag ( page 15 ) .

•If the rear-discharge plug is not installed, grip it by

the handle, raise the rear deector , and insert it

into the rear-discharge chute until the latch locks

into place; refer to Figure 17 .

g426214

Figure 17

Bagging the Clippings

Use the grass bag when you want to collect grass and leaf clippings from the lawn.

If the side-discharge chute is on the mower , remove it before bagging the clippings; refer to Removing the

Side-Discharge Chute ( page 15 ) .

Installing the Grass Bag

1. Raise and hold up the rear deector (A of Figure 18 ).

2. Remove the rear-discharge plug by pulling down on the latch with your thumb and pulling the plug out

from the machine (B of Figure 18 ).

3. Install the bag rod into the notches at the base of the handle and rock the bag back and forth to ensure

that the rod is seated at the bottom of both notches (C of Figure 18 ).

4. Lower the rear deector until it rests on the grass bag.

14

g426289

Figure 18

Removing the Grass Bag

DANGER

The machine can throw grass clippings and other objects through an opening in the machine

housing. Objects thrown with enough force could cause serious personal injury or death to

you or to bystanders.

• Never remove the grass bag and then start the machine without the discharge plug installed

on the machine.

• Never open the rear deector on the machine when the machine is running.

T o remove the bag, reverse the steps in Installing the Grass Bag ( page 14 ) .

Side-Discharging the

Clippings

Use the side discharge for cutting very tall grass.

If the bag is on the machine, remove it and insert the

rear-discharge plug; refer to Removing the Grass Bag

( page 15 ) before side-discharging the clippings.

Important: Ensure that the rear-discharge plug is

in place before you recycle the clippings ( Figure

17 ).

Installing the Side-Discharge

Chute

1. Remove the side-discharge deector bracket

and fasteners (A of Figure 19 ).

2. Unlatch and lift up the side deector and install

the side-discharge chute (B, C, and D of Figure

19 ).

g456257

Figure 19

1. Locknut

3. Deector bracket

2. Bolt

Removing the Side-Discharge

Chute

T o remove the side-discharge chute, lift up the side

deector , remove the side-discharge chute, and lower

the side-discharge deector until it latches securely .

15

Important: Install the deector bracket when not

using the side-discharge chute (A of Figure 19 ).

Operating T ips

General Mowing T ips

•Inspect the area where you will use the machine

and remove all objects that the machine could

throw .

•A void striking solid objects with the blades. Never

deliberately mow over any object.

•If the machine strikes an object or starts to vibrate,

immediately shut of f the machine, wait for all

moving parts to stop, remove the battery pack

from the machine, and examine the machine for

damage.

•For best performance, install new T oro blades

before the cutting season begins or when

necessary .

Cutting Grass

•Cut only about a third of the grass blade at a time.

For improved quality of cut, runtime, and bagging,

cut grass at a higher height of cut.

•Do not cut below 51 mm (2 inches) unless the

grass is sparse or it is late fall when grass growth

begins to slow down.

•When cutting grass over 15 cm (6 inches) tall,

mow at the highest cutting height setting and walk

slower; then mow again at a lower setting for the

best lawn appearance. If the grass is too long, the

machine may plug and cause the motor to stall.

•W et grass and leaves tend to clump on the yard

and can cause the machine to plug or the motor to

stall. A void mowing in wet conditions.

•Be aware of a potential re hazard in very dry

conditions, follow all local re warnings, and keep

the machine free of dry grass and leaf debris.

•Alternate the mowing direction. This helps

disperse the clippings over the lawn for even

fertilization.

•If the nished lawn appearance is unsatisfactory ,

try 1 or more of the following:

– Replace the blades or have them sharpened.

– W alk at a slower pace while mowing.

– Raise the cutting height on your machine.

– Cut the grass more frequently .

– Overlap cutting swaths instead of cutting a full

swath with each pass.

Cutting Leaves

•After cutting the lawn, ensure that half of the lawn

shows through the cut leaf cover . Y ou may need

to make more than a single pass over the leaves.

•If there are more than 13 cm (5 inches) of leaves

on the lawn, mow at a higher cutting height and

then again at the desired cutting height.

•Slow down your mowing speed if the machine

does not cut the leaves nely enough.

16

After Operation

Removing the Battery Pack

from the Machine

1. Lift up the battery-compartment lid.

2. Press the battery-pack latch to release the

battery pack and remove the battery pack.

3. Close the battery-compartment lid.

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 10 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents on the battery and charger

are clear of any dust and debris.

g290533

Figure 20

1. Battery pack cavity

5. LED indicators (current

charge)

2. Battery pack venting areas 6. Handle

3. Battery pack terminals

7. Charger LED indicator

light

4. Battery-charge-indicator

button

8. Charger venting areas

2. Line up the cavity in the battery pack ( Figure 20 )

with the tongue on the charger .

3. Slide the battery pack into the charger until it is

fully seated ( Figure 20 ).

4. T o remove the battery pack, slide the battery

backward out of the charger .

5. Refer to the following table to interpret the LED

indicator light on the battery charger .

Indicator

light

Indicates

Of f

No battery pack inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the appropriate temperature range

Red

blinking

Battery pack charging fault*

*Refer to T roubleshooting ( page 25 ) for more

information.

Important: The battery can be left on the charger

for short periods between uses.

If the battery will not be used for longer periods,

remove the battery from the charger; refer to

Storage ( page 24 ) .

Cleaning Under the

Machine

Service Interval : After each use

W ARNING

A broken or missing washout tting could

expose you and others to thrown objects or

blade contact. Contact with a blade or thrown

debris can cause injury or death.

• Replace a broken or missing washout

tting immediately , before using the

machine again.

• Never put your hands or feet under the

machine or through openings in the

machine.

1. Move the machine to a level surface.

2. Shut of f the machine and wait for all moving

parts to stop before leaving the operating

position.

3. Lower the machine to its lowest cutting-height

setting. Refer to Adjusting the Cutting Height

( page 12 ) .

17

4. Attach a hose to the washout tting, and turn the

water on high ( Figure 21 ).

Note: Spread petroleum jelly on the washout

tting O-ring to make the coupling slide on

easier and protect the O-ring.

g003934

Figure 21

1. W ashout tting 3. O-ring

2. Hose

4. Coupling

5. Start the machine, engage the blade-control

lever , and let the machine run for 1 to 3 minutes

with the blades turning.

6. Disengage the blade-control lever , shut of f the

machine, and wait for all moving parts to stop.

7. Shut of f the water and remove the coupling from

the washout tting.

Note: If the machine is not clean after a single

washing, soak it and let it stand for 30 minutes.

Then repeat the process.

8. Run the machine again and engage the blades

for 1 to 3 minutes to remove the excess water .

18

La page charge ...

Toro eTimeMaster eTM76 76cm 60V Lawn Mower Manuel utilisateur

Ce manuel convient également à

Toro eTimeMaster eTM76 76cm 60V Lawn Mower Manuel utilisateur

dans d''autres langues

Documents connexes