Robern CRAFT Series Manuel utilisateur

INSTALLATION GUIDE

DESIGNED IN BRISTOL, PA U.S.A.

ASSEMBLED IN CHINA

PORTRAY™ ELECTRIC UPGRADE

1

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

PORTRAY ELECTRIC UPGRADE

Important safety instructions

Save these instructions

Tools Needed - 2

Parts - 2

Prep for Install - 3

Swap Outlet Side - 4

Installation - 8

Care and Maintenance - 14

Warranty - 15

CONTENTS

Compatible With:

PL Portray Series Cabinets

P2C16, P2C20, P2C24

2

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

TOOLS NEEDED

Shipped Partially Assembled

PARTS

[205-3097]

Sub Assembly

[203-1115]

#6-32 x 1/4”

Screw

[203-1285]

#8-32 x 1/4”

Screw

[203-1055]

Romex

Connector

[211-1335]

Left Hand Finisher

[210-1671]

Mounting Bracket

[211-1334]

Right Hand Finisher

3

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

1. Remove the four #6-32 x 1/4” screws [203-1115] shown to remove the mounting bracket

from the assembly. Save these screws for reassembly later.

PREP FOR INSTALL

[203-1115]

#6-32 x 1/4”

Screw

1

4

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

NOTE: Electrical box assembly is shipped with the outlet mounted on the right-hand side.

If desired, follow steps 2 through 3 to mount the outlet on the left-hand side. Otherwise,

proceed to INSTALLATION on page 8.

2. Disconnect the Black and White Power Wires for the outlet and Black (L) and White (N)

Power Wires for the 12v driver from the WAGO terminals inside the assembly by lifting up

on the orange tab for each terminal. Set the loose 3 tab WAGO terminal blocks aside for

reassembly later.

Remove the two #6-32 x 1/4” screws [203-1115] securing the outlet and the two

#6-32 x 1/4” screws [203-1115] securing the driver.

Disconnect the JST connectors (white) between the power supply and the circuit board

(located at the top of the electrical box assembly).

SWAP OUTLET SIDE (OPTIONAL)

5

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

SWAP OUTLET SIDE (OPTIONAL)

2

[203-1115]

#6-32 x 1/4”

Screw

6

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

3. Position the outlet on the left-hand side and re-install with the two #6-32 x 1/4” screws

[203-1115] removed previously.

Reconnect the JST connectors (white) between the power supply and the circuit board.

Position the power supply on the right-hand side, and install with the two #6-32 x 1/4”

screws [203-1115] removed previously. Be careful not to pinch or cut any wires.

Reconnect the Black (L) and White (N) thick power wires from the outlet and power supply

to the Wago connectors by lifting the three orange tabs of the 3-tab WAGO connector.

Insert the Black (L) wire from the power supply in one of the square holes in the WAGO

connector; insert the Black wire from the outlet in the second square hole in the WAGO

connector. Lower the three tabs on the 3 tab WAGO connector. Repeat this process

for the White (N) wires from the power supply and outlet on the second 3-tab WAGO

connector. When you are nished, the Black (L) wires should be in one WAGO connector;

the White (N) wires should be in another.

NOTE: Ground (GREEN) Screw must remain on top of outlet as shown in Figure 3.

SWAP OUTLET SIDE (OPTIONAL)

7

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

SWAP OUTLET SIDE (OPTIONAL)

3

[203-1115]

#6-32 x 1/4”

Screw

GROUND SCREW

8

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

DANGER - RISK OF SHOCK - DISCONNECT

POWER BEFORE INSTALLATION

All wiring should be done by a qualied licensed electrician.

WARNING: To reduce the risk of electrical shock, shut o power before wiring the electrical box.

CAUTION: Requires 120 VAC 20 Amp GFI protected circuit.

CAUTION: This product must be connected to a grounded, metal permanent wiring system,

or an equipment-grounding conductor must be run with the circuit conductors and connected

to the equipment grounding terminal or lead on the product.

WARNING: Electrical box must be wired to a 20 Amp GFI (Ground Fault Interrupter)

protected circuit when used in bathrooms and all other locations required by the National

Electric Code.

ATTENTION: Verify that all power is removed from the source power wires before proceeding.

4. Strip outer jacket of the romex wire, exposing 2-3” of the White, Black, and Ground Wires.

Pull power wire through opening in cabinet and through wire grommet in mounting bracket

about 2-3” or until the outer jacket of the source power wire just protrudes through the

Romex connector.

Secure the mounting bracket removed in Step 1 to the cabinet using the two supplied

#8-32 x 1/4” screws [203-1285].

INSTALLATION

9

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

INSTALLATION

4

[203-1285]

#8-32 x 1/4”

Screw

10

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

5. Make eld connections as per wiring diagram.

INSTALLATION

5

Black (L)

White (N)

Green (G)

Ground

Ground (G)

120 VAC

20A GFI

Field Wire

Connection

Circuit

Breaker

Electric Upgrade Enclosure

Outlet

Driver

11

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

6. Position the electrical box assembly over the mounting bracket and secure with the four

#6-32 x 1/4” screws [203-1115] removed in Step 1. Be sure to guide the source power

wires to the inside of the Electrical Box, and not to pinch or cut any wires.

INSTALLATION

6

[203-1115]

#6-32 x 1/4”

Screw

12

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

7. Apply covers to electrical box working the snaps in from the front to the back.

INSTALLATION

7

13

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

8. Apply power to electrical box and test the outlet and night light.

NOTE: Cabinet interior light will ash when rst powered. May stay illuminated for up to 15

seconds, then go out. After an additional 15 - 20 seconds, the light will begin to function

normally.

NOTE: Cabinet interior light will power on for 15 seconds when motion is detected.

INSTALLATION

14

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

The Portray Electrical Upgrade is constructed of high-quality materials. Handle with care.

Ensure that power to the device has been turned o before cleaning.

Use only a soft damp cloth to clean. When cleaning, spray the cloth, not the product.

A 50/50 solution of water and isopropyl alcohol is recommended for cleaning product.

Ammonia or vinegar-based cleaners can damage the product.

CARE AND MAINTENANCE

No Ammonia

Sans Ammoniac

Sin Amoniaco

No Vinegar

Sans Vinaigre

Sin Vinagre

No Ammonia

No Vinegar

15

800.877.2376 www.robern.com

Part no. CB-209-1346 09/23/20

Portray Electric Upgrade

LIMITED ONE-YEAR TERM

Robern warrants to the original purchaser that, it will, at its election repair, replace

or make appropriate adjustment to products made by this company shown to have

signicant defects in material or workmanship which are reported to Robern in writing

within one (1) year from the date of delivery. Robern is not responsible for installation

costs. The warranty is void in the event the product is damaged in transit, or if damage

or failure is caused by abuse, misuse, abnormal usage, faulty installation, damage in an

accident, improper maintenance, or any repairs other than those authorized by Robern.

At the expiration of the one year warranty period, Robern shall be under no further

obligation under any warranty, expressed or implied, including the implied warranty of

merchantability. Robern shall not be liable for any consequential damages arising out of

or in connection with the use or performance of its products. Some states do not allow

limitations on how long an implied warranty lasts or do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion may not apply

to you.

Any liability against Robern under any implied warranty, including the warranty of

merchantability, is expressly limited to the terms of this warranty. Permission to return any

merchandise under this warranty must be authorized by Robern and returned prepaid by

the purchaser. Claims under this warranty should be sent directly to your dealer.

WARRANTY

GUIDE D’INSTALLATION

GUÍA DE INSTALACIÓN

PORTRAY™ MISE À NIVEAU ÉLECTRIQUE

PORTRAY™ ACTUALIZACIÓN ELECTRICA

CONÇU À BRISTOL, PA U.S.A.

FABRIQUÉ EN CHINE

DISEÑADO EN BRISTOL, PA EE. UU.

HECHO EN CHINA

1

800.877.2376 www.robern.com

No. de pièce / Pieza n.° CB-209-1346 09/23/20

Portray Mise à Niveau Électrique

Portray Actualización Electrica

Portray Mise à Niveau Électrique

Consignes de sécurité importantes

Enregistrez ces instructions

Portray Actualización Electrica

Instrucciones de seguridad importantes

Guarda estas instrucciones

Compatible avec / Compatible con:

PL Portray Series Cabinets

P2C16, P2C20, P2C24

Outils nécessaires - 2

Pièces - 2

Préparation pour l’installation - 3

Remplacez le côté

de la prise de courant - 4

Installation - 8

Utilisation et Entretien - 14

Garantie - 15

Herramientas necesarias - 2

Piezas - 2

Preparación para la instalación - 3

Intercambio del lado

de la toma de corriente - 4

Montaje - 8

Uso y Mantenimiento - 14

Garantía - 15

TABLE DES MATIÈRES CONTENIDO

2

800.877.2376 www.robern.com

No. de pièce / Pieza n.° CB-209-1346 09/23/20

Portray Mise à Niveau Électrique

Portray Actualización Electrica

Expédié Partiellement Assemblé /

Enviado Parcialmente Ensamblado

[205-3097]

Sous-assemblage /

Subensamblaje

[203-1115]

#6-32 x 1/4”

Vis / Tornillo

[203-1285]

#8-32 x 1/4”

Vis / Tornillo

[203-1055]

Romex Connecteur /

Romex Conector

[211-1335]

Finisseur à Gauche /

Acabadora Izquierda

[210-1671]

Support de Montage /

Soporte de Montaje

[211-1334]

Finisseur à Droite /

Acabadora Derecha

OUTILS NÉCESSAIRES HERRAMIENTAS

NECESARIAS

PIÈCES PIEZAS

3

800.877.2376 www.robern.com

No. de pièce / Pieza n.° CB-209-1346 09/23/20

Portray Mise à Niveau Électrique

Portray Actualización Electrica

[203-1115]

#6-32 x 1/4”

Vis / Tornillo

1

PRÉPARATION POUR

L’INSTALLATION

PREPARACIÓN PARA

LA INSTALACIÓN

1. Retirez les quatre vis #6-32 x 1/4 po

[203-1115] spéciée pour retirer le support de

montage de l’ensemble. Conservez ces vis pour

un remonter ultérieurement.

1. Extraiga los cuatro tornillos #6-32 x 1/4”

[203-1115] que se muestran para sacar el

soporte de montaje del conjunto. Guarde estos

tornillos para volver a colocarlos más adelante.

La page charge ...

Robern CRAFT Series Manuel utilisateur

Robern CRAFT Series Manuel utilisateur

dans d''autres langues

Documents connexes