WORX Tools Chainsaw WT525 Manuel utilisateur

Cordless Circular Saw ENG

Scie Circulaire Sans Cordon F

Sierra Circular Inalámbrica ES

Pag 02

Pag 18

Pag 36

5 1/2”/18V

WT525

NA-WT525-M-050727.indd 1 2005-7-27 17:45:56

Cordless Circular Saw WT525

SAFETY INSTRUCTIONS

WARNING! Read and understand all instructions. Failure to follow all instructions

listed below, may result in electric shock, ﬁre and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. WORK AREA

a) Keep your work area clean and well lit. Cluttered benches and dark areas invite ac-

cidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

ﬂammable liquids, gases or dusts. Power tools create sparks which may ignite the dust

or fumes.

c) Keep by-standers, children, and visitors away while operating a power tool. Dis-

tractions can cause you to lose control.

2. ELECTRICAL SAFETY

a) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the speciﬁed charger for the battery. A charger that may be suit-

able for one type of battery may create a risk of ﬁre when used with another battery.

b) Use battery operated tool only with speciﬁcally designated battery pack. Use of

any other batteries may create a risk of ﬁre.

3. PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the inﬂuence of drugs, alcohol,

or medication. A moment of inattention while operating power tools may result in serious

personal injury.

b) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts. Keep handles dry, clean and free from oil and

grease. Rubber gloves and non-skid footwear are recommended when working outdoors.

c) Avoid accidental starting. Be sure switch is in the locked or “OFF” position before

inserting battery pack. Carrying tools with your ﬁnger on the switch or inserting the bat-

tery pack into a tool with the switch “ON” invites accidents.

d) Remove all adjusting keys and wrenches. Make a habit of checking that adjusting keys,

wrenches, etc. are removed from the tool before turning it “ON”.

e) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

f) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection may be used for appropriate conditions.

g) Keep hands away from all cutting edges and moving parts.

h) If devices are provided for the connection of dust extraction and collection facili-

ties, ensure these are connected and properly used. Use of these devices can reduce

dust-related hazards.

4. TOOL USE AND CARE

a) Use clamps or other practical way to secure and support the work-piece to a

stable platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

b) Do not force tool. Use the correct tool for your application. The correct tool will do the

0302

NA-WT525-M-050727.indd 2 2005-7-27 17:45:57

Cordless Circular Saw WT525

job better and safer at the rate for which it is designed. Excessive force only causes operator fatigue,

increased wear and reduced control.

c) Do not use tool if switch does not turn it “ON” or “OFF”. A tool that cannot be con-

trolled with the switch is dangerous and must be repaired.

d) Disconnect battery pack from tool or place the switch in the “LOCKED” or “OFF”

position before making any adjustments, changing accessories, or storing the

tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

e) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

f) When battery pack is not in use, keep it away from other metal objects like: pa-

per clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause sparks, burns, or a ﬁre.

g) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges, are less likely to bind and easier to control.

h) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

i) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on an-

other tool.

j) Use the right tool. Do not force the tool or attachment to do a job for which it was not

designed

5. SERVICE

a) Tool service must be performed only by qualiﬁed repair personnel. Service or main-

tenance performed by unqualiﬁed personnel could result in a risk of injury.

b) When servicing a tool, use only identical replacement parts. Follow instructions

in the Maintenance section of this manual. Use of unauthorized parts or failure to fol-

low Maintenance Instructions may create a risk of electric shock or injury.

ADDITIONAL SAFETY RULES - FOR CORDLESS CIRCULAR

SAWS

WARNING! Failure to follow these rules may result in serious personal injury.

1) Hold tool by insulated gripping surfaces when performing an operation where the

cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2) Always keep your hands away from cutting area. Do not reach under the material being

cut because the nearness of the blade to your hand is hidden from your sight.

3) Always wear eye protectors when using tool. Use a dust mask or respirator for ap-

plications which generate dust.

4) Do not use dull or damaged blades. Sharp blades will do the job better and safer. Bent

blades can break easily or cause kickback.

5) The base plate must always be held ﬁrmly against the material being cut to reduce

saw vibration, blade jumping and blade breakage.

6) Never stop the cutting blade by applying side pressure to the blade.

7) Only withdraw the blade from the cut when the blade has stopped moving.

0302

NA-WT525-M-050727.indd 3 2005-7-27 17:45:58

Cordless Circular Saw WT525

8) Do not reach underneath the work-piece while cutting. The guard cannot protect you

from the blade below the work-piece.

9) Your circular saw is a hand-held tool, do not clamp your circular saw.

10) Before cutting, check the cutting line is free of nails, screws, etc.

11) Do not cut small work-pieces with a circular saw. If possible, use a jigsaw.

12) Only use blades that the rated speed exceeds the saw no load speed.

13) Never remove the guard system. Never use the saw if the guard system does not func-

tion correctly. Never lock the moving guard open. The guard must move freely.

14) ALWAYS check lower guard to ensure proper closing before each use. Do not op-

erate saw if lower guard does not move freely and close instantly. Never clamp or

tie the lower guard in the open position. If saw is accidentally dropped, lower guard may be

bent. Raise the lower guard with the Lower Guard Lever and make sure guard moves freely

and does not touch the blade or any other part of the saw, in any angle and depth of cut.

15) Always check walls, ﬂoors and ceilings to avoid hidden power cable and pipes.

16) Do not cut material containing asbestos.

17) Do not use metal or stone saw blades. Only use wood saw blades.

18) Do not use circular saw to cut tree limbs or logs.

19) Do not use any abrasive wheels.

20) Keep your body positioned to either side of the saw, but not in-line with the saw

blade. KICKBACK could cause the saw to jump backwards.

21) Be aware that this tool is always in an operating condition because it does not

have to be plugged into an electrical outlet.

22) Disconnect battery pack from the tool or place switch in the “LOCKED” or “OFF”

position before making any assembly, adjustments or changing accessories. Such

preventive safety measures reduce the risk of starting the tool accidentally.

23) Save these instructions. Refer to them frequently and use them to instruct others who

may use this tool. If someone borrows this tool, make sure they have these instructions.

WARNING! Some dust created by power sanding, sawing, grinding, drilling and

other construction activities contains chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemical are:

• Lead from lead-based paint

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically-treated lumber

Your risk to these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals:

• Work in a well ventilated area

• Work with approved safety equipment, such as those dust masks that are speciﬁcally designed to

ﬁlter out microscopic particles.

BATTERY / CHARGER

1. Do not dispose of batteries in ﬁre, or with household waste. Return exhausted batter-

ies to your local collection or recycling point.

2. Before using battery charger, read all instructions and cautionary markings on (1)

battery charger, (2) battery pack, and (3) product using battery.

3. CAUTION: To reduce the risk of injury, a WORX charger should only be used to

charge a WORX battery pack. Other types of batteries may burst causing personal injury

and damage. Do not charge a WORX battery pack with any other charger.

4. Do not store the battery pack in temperatures over +102ºF (39ºC).

0504

NA-WT525-M-050727.indd 4 2005-7-27 17:45:58

Cordless Circular Saw WT525

0504

Read the manual

Warning

Wear safety goggles, dust mask

and ear protection

Use inside only

1-Hour Charging Time

Double insulation

Do not expose to rain or water

Do not burn

Do not dispose of batteries. Return

exhausted batteries to your local col-

lection or recycling point.

Always charge battery between 36ºF

- 95ºF (2ºC -35ºC)

5. Always charge the battery pack between temperatures 36ºF to 95ºF (2ºC to 35

ºC). Ideal charging temperature is 65ºF to 84ºF (18ºC to 29ºC).

6. Avoid short circuit of the battery pack connections (screws & nails).

7. Charger is double insulated for additional electrical safety.

8. Do not expose charger to rain or water.

9. Charger is for indoor use only.

10. Do not incinerate or burn the battery pack, it may explode.

11. Do not charge a damaged battery pack.

12. Do not charge non-rechargeable batteries.

13. Replace any damaged power supply cords on your charger.

14. Always disconnect the charger power supply before making or breaking the con-

nections to the battery pack.

15. Battery pack and charger will be warm during charging, this is normal.

16. When not in use, remove a charged battery pack from the charger.

17. Always remove the battery pack from the charger immediately after re-charging is

completed.

WARNING: A small amount of electrolyte could leak from the battery pack under

extremes of temperature or after heavy use. Avoid contact with skin and eyes.

Wash off immediately from your skin and hands using clean water. For eye contact,

rinse thoroughly with clean water and seek medical treatment immediately.

The label on your tool may include the following symbols:

V...................................................................................................................................................................Volts

A.................................................................................................................................................................Amps

Hz.................................................................................................................................................................Hertz

~..........................................................................................................................................Alternating current

no ...............................................................................................................................................No load speed

................................................................................................Class II Construction / Double insulation

SYMBOLS

NA-WT525-M-050727.indd 5 2005-7-27 17:46:00

Cordless Circular Saw WT525

0706

1. SAFETY ON/OFF SWITCH

2. FRONT HANDLE

3. SAW BLADE

4. DEPTH OF CUT SCALE

5. BASE PLATE

6. BASE PLATE ANGLE SCALE

7. PARALLEL GUIDE

8. DUST EXTRACTION OUTLET

9. SPINDLE LOCK BUTTON

10. OUTER FLANGE

11. BLADE BOLT

12. LOWER GUARD LEVER

16

15

20

13

18

19

17

14

10

11

12

8

21

3

5

9

6

7

2

41

NA-WT525-M-050727.indd 6 2005-7-27 17:46:02

Cordless Circular Saw WT525

0706

13. DEPTH OF CUT ADJUSTMENT LEVER

14. BASE PLATE BEVEL LOCK

15. BATTERY PACK

16. BATTERY PACK RELEASE LATCH

17. CHARGER

18. CHARGED INDICATOR LIGHT (GREEN)

19. CHARGING INDICATOR LIGHT (RED)

20. HEX KEY HOLDER

21. MAIN HANDLE

TECHNICAL DATA

Voltage rating: 18V

No load speed: 3,300rpm

Bevel Capacity: 0-50º

Blade Size: 5 1/2” (140mm)

Blade Bore: 3/8” (10mm)

Maximum Cutting Capacity:

Cutting Capacity at 90º 1 5/8” (41.5mm)

Cutting Capacity at 45º 1 3/16” (30mm)

Machine Weight: 7.7lbs (3.5Kg)

ACCESSORIES

Batteries two(2)18V - 2.0Ah Ni-Cd (WT525/WT940K)

1-Hour Charger Voltage 120V~60Hz

Hex Key 1pc

Parallel Guide 1pc

We recommend that you purchase your accessories from the same store that sold you the tool.

Use good quality accessories marked with a well-known brand name. Choose the type according

to the work you intend to undertake. Refer to the accessory packaging for further details. Store

personnel can assist you and offer advice.

NA-WT525-M-050727.indd 7 2005-7-27 17:46:03

Cordless Circular Saw WT525

0908

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction

book carefully.

KICKBACK

Further safety instructions for all saws

Causes and operator prevention of kickback:

- kickback is a sudden reaction to pinched, bound or mis-

align saw blade, causing an uncontrolled saw to lift up

and out of the work-piece toward the operator;

- when the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator;

- if the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the

top surface of the wood causing the blade to climb out of

the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect op-

erating procedures or conditions and can be avoided by

taking proper precautions as given below.

a. Maintain a ﬁrm grip with both hands on the saw and

position your arms to resist kickback forces. Position your

body to either side of the blade, but not in line with the

blade. Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the operator, if

proper precautions are taken.

b. When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw motion-

less in the material until the blade comes to a complete

stop. Never attempt to remove the saw from the work

or pull the saw backward while the blade is in motion or

kickback may occur. Investigate and take corrective ac-

tions to eliminate the cause of blade binding.

c. When restarting a saw in the work-piece, center the

saw blade in the kerf and check that saw teeth are not

engaged into the material. If saw blade is binding, it may

walk up or kickback from the work-piece as the saw is

restarted.

d. Support large panels to minimize the risk of blade

pinching and kickback.

Large panels tend to sag under their own weight. Sup-

ports must be placed under the panel on both sides, near

the line of cut and near the edge of the panel.

e. Do not use dull or damaged blades. Unsharpened or

improperly set teeth produce narrow kerf causing exces-

sive friction, blade binding and kickback.

f. Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

NA-WT525-M-050727.indd 8 2005-7-27 17:46:03

Cordless Circular Saw WT525

g. Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

POCKET CUTTING

Pocket cutting (soft materials only) This operation re-

quires much skill with a saw and must only be carried

out by a competent person.

Warning: the blade teeth are exposed during this

operation so proceed with extreme caution.

a. Clearly mark the area to be cut.

b. Set the depth of cut on the saw.

c. Position the saw over the marked area with the front

edge of the base plate resting on the work surface and

cutting guide aligned with marked line on work-piece

(See Fig 8).

d. Ensure the blade is not touching but is close to the

work surface. The moving lower guard must be rotated

open by using lever (5).

e. Switch the saw on and gently swing the blade down

into the material but maintain a pivoting force on the

front edge of the base. The moving lower guard can now

be released for normal action of the guard.

BLADE GUARDS

a. Check lower guard for proper closing before

each use. Do not operate the saw if lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open posi-

tion. If saw is accidentally dropped, lower guard may be

bent. Raise the lower guard with the retracting handle

and make sure it moves freely and does not touch the

blade or any other parts, in all angles and depths of cut.

b. Check the operation of the lower guard spring.

If the guard and the spring are not operating prop-

erly, they must be serviced before use. Lower guard

may operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c. Lower guard should be retracted manually only

for special cuts such as “plunge cuts” and “com-

pound cuts”. Raise lower guard by retracting han-

dle and as soon as blade enters the material, the

lower guard must be released. For all other sawing,

the lower guard should operate automatically.

d. Always observe that the lower guard is cover-

ing the blade before placing saw down on bench

or ﬂoor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path. Be

aware of the time it takes for blade to stop after switch

is released.

0908

NA-WT525-M-050727.indd 9 2005-7-27 17:46:04

Cordless Circular Saw WT525

1. BEFORE USING YOUR CORDLESS CIRCULAR

SAW

Your battery pack is UNCHARGED and you must charge

once before use. Your battery pack will not be fully

charged until you have performed several charge and

discharge operations by charging & working with your

saw. After this your battery pack performance will im-

prove.

Warning: The charger and battery pack are specif-

ically designed to work together so do not attempt

to use any other devices. Never insert or allow metallic

objects into your charger or battery pack connections be-

cause an electrical failure and hazard will occur.

2. HOW TO CHARGE YOUR BATTERY PACK (See

Fig 1)

1) Connect the battery charger to the power supply. The

red light will illuminate for 3 seconds and then it will go

out.

Note: If the red light ﬂashes at a rapid rate (approx. 5

ﬂashes per second), this means that the charger has

failed and must be replaced.

2) Fully insert the battery pack into the charger. With

a normal charging process, only the red light will illu-

minate to show charging has started. The red light will

remain on during the charging process. A discharged

battery at normal ambient temperature will take approx-

imately 1 hour to reach full charge.

Note: If the battery temperature is lower than 32ºF (0ºC),

the green light will ﬂash slowly (approximately 2 ﬂashes

per second). Remove the battery and allow the battery

to warm-up to a charging temperature between 36ºF to

95ºF (2ºC and 35ºC).

If the battery temperature is over 140ºF (60ºC), the green

light will ﬂash rapidly (approximately 5 ﬂashes per sec-

ond). Remove the battery and allow the battery to cool-

down to a charging temperature between 36ºF to 95ºF

(2ºC and 35ºC).

If the battery temperature is over 176ºF (80ºC), the charg-

ing process will be stopped, and the red light will ﬂash

with a low speed (approximately 2 ﬂashes per second).

The battery must be replaced.

3) When the charging is complete, only the green light

will illuminate.

Note: When the battery is under charging and its volt-

age cannot reach 4V in 2 minutes, we consider the bat-

tery to be “dead”, and the red light will ﬂash with a low

speed (approximately 2 ﬂashes per second). Remove the

1110

Fig 1

18

19

17

NA-WT525-M-050727.indd 10 2005-7-27 17:46:05

Cordless Circular Saw WT525

“dead” battery from the charger and replace with a new

battery.

4) When the charging process is ﬁnished, the battery is

still charging with a current 50mA.

Note: The charger timer-circuit and battery pack temper-

ature safety-cutout device prevents overcharging of the

battery pack. However, it is recommended to remove the

battery from the charger when the charging cycle has

been completed as indicated by the illumination of the

green light.

3. TO REMOVE OR INSTALL BATTERY PACK

Locate latches on side of battery pack and depress both

sides to release battery pack from your saw. Remove

battery pack from your saw. After recharge insert the

battery pack into saw’s battery port. A simple push

and slight pressure will be sufﬁcient.

4. SAFETY ON/OFF SWITCH

Your switch is locked off to prevent accidental starting.

Depress lock off button (a) then on/off switch (b) and re-

lease lock off button (a). Your switch is now on. To switch

off just release the on/off switch (See Fig 2).

5. CHANGING A SAW BLADE

Loosen the locking lever (13) and raise the saw body

away from the base plate. Take out the Hex key (20) from

the base plate. Press the spindle lock button (9) and

use the hex key provided to remove the bolt and outer

ﬂange. Rotate lower guard counter-clockwise and hold

open using the lever (12) while changing the saw blade.

Ensure the blade bore is located on the inner ﬂange and

the blade direction arrow points in the same direction

as the lower guard arrow. Check that the blade surface

and ﬂanges are clean. Press the spindle lock again and

re-ﬁt the outer ﬂange over the spindle ﬂats, bolt with 1/4

turn more than ﬁnger tight. Check the blade is securely

clamped (See Fig 3).

1110

Fig 2

a

b

Status Light ON/OFF/Flash

Battery charging red on

Charger failure red fast ﬂash (5/sec)

Battery <32ºF (0ºC) green slow ﬂash (2/sec)

Battery + 140ºF (60ºC) green fast ﬂash (5/sec)

Battery + 176ºF (80ºC) red slow ﬂash (2/sec)

Battery dead red slow ﬂash (2/sec)

Charging complete green on

NA-WT525-M-050727.indd 11 2005-7-27 17:46:06

Cordless Circular Saw WT525

Warning: Blade teeth are very sharp. Wear gloves

when changing saw blades. For best cutting re-

sults ensure you use a saw blade suited to the material

and cut quality you need. Ensure the blade is suitable

for the rated speed of the tool. Only use carbide-tipped

blades in this tool.

6. DEPTH OF CUT ADJUSTMENT

Lift the depth of cut locking lever (13) and raise the saw

body away from the base plate (5). Set the depth of cut

using the scale (4) and push the lever down to lock (See

Fig 4). Always add 1/8” (3mm) to your depth of cut so

the blade can cut through the material. The riving knife

automatically adjusts position when the depth of cut is

changed.

7. BASE PLATE

Adjusting the angle of the base plate (5) enables bev-

el cutting. The base plate must always be held ﬁrmly

against the material being cut to reduce saw vibration,

blade jumping or blade breakage.

8. BASE PLATE ANGLE ADJUSTMENT

Loosen the base plate bevel lock knob (14) and rotate the

base plate (5) to set the bevel angle using the base plate

angle scale (6). Then clamp the base plate (6) in position

using the lock knobs (14) (See Fig 5). Finally, check the

angle and ensure the base plate is ﬁrmly clamped. The

angle markings on the angle scale are accurate for most

general purposes but it is recommended, for accurate

work, to set the angle with a protractor and make a test

cut on other material. Do not use the depth of cut scale

when making bevel cuts due to possible inaccuracy.

9. PARALLEL GUIDE ADJUSTMENT

The parallel guide is used for making cuts parallel to a

work-piece edge at a chosen distance. Slide the paral-

lel guide (7) arm through both ﬁxtures to achieve the

required cutting distance and tighten screw to lock into

position (See Fig 6). It can be used from both sides of

the base plate (5). The cutting distance is shown on the

guide scale and by using the 90º or 45º notch edge on

the base plate (5). Always make a trial cut to check the

setting.

10. DUST EXTRACTION OUTLET

To remove sawdust, connect a suitable external dust ex-

traction device (e.g. vacuum cleaner) to the dust extrac-

tion outlet (8) using a ﬂexible hose connection. Ensure

the hose connection is secure.

1312

Fig 6

Fig 3

Fig 4

Fig 5

NA-WT525-M-050727.indd 12 2005-7-27 17:46:07

Cordless Circular Saw WT525

1312

11. DISPOSAL OF AN EXHAUSTED BATTERY PACK

To preserve natural resources, please recycle or dis-

pose of the battery pack properly. This battery pack

contains nickel-cadmium batteries. Consult your local

waste authority for information regarding available re-

cycling and/or disposal options. Discharge your battery

pack by operating your saw, then remove the battery

pack from the saw housing and cover the battery pack

connections with heavy duty adhesive tape to prevent

short circuit and energy discharge. Do not attempt to

open or remove any of the components.

WORKING HINTS FOR YOUR CIR-

CULAR SAW

a) If your power tool becomes too hot, run your circular

saw no load for 2-3 minutes to cool the motor. Avoid

prolonged usage at very low speeds.

b) Always use a blade suited to the material and material

thickness to be cut. The quality of cut will improve as the

number of blade teeth increase.

c) Always ensure the work-piece is ﬁrmly held or

clamped to prevent movement.

d) Support large panels close to the cut line. Any move-

ment of the material may affect the quality of the cut.

e) The blade cuts on the upward stroke and may chip the

uppermost surface or edges of your work piece. When

cutting, ensure your uppermost surface is a non-visible

surface when your work is ﬁnished. Feeding too fast sig-

niﬁcantly reduces the performance of the machine and

shortens the life of the saw blade. Always face the good

side of the work-piece down, to ensure minimum splin-

tering. Only use sharp saw blades of the correct type.

FREQUENTLY ASKED QUESTIONS

1. WHY DOES THE SAW NOT TURN ON WHEN YOU

PRESS THE SWITCH?

The safety on/off switch (b) is locked and you must de-

press the button (a) ﬁrst (See Fig 2).

2. THE SAW ROTATES SLOW. WHY?

If the battery is not fully charged, recharge the battery

with the supplied battery charger.

Note: Do not charge the battery with a different charger.

Charge battery pack only with the charger provided.

3. I CANNOT FIT THE BATTERY INTO THE BAT-

NA-WT525-M-050727.indd 13 2005-7-27 17:46:08

Cordless Circular Saw WT525

1514

TERY CHARGER.WHY?

The battery can be inserted into the charger only in one

direction. Turn the battery around until it can be inserted

into the slot, the red LED light should turn on when the

battery is charging (See Fig 7.1, 7.2).

4. REASONS FOR DIFFERENT CHARGING TIMES.

Your charge time can be affected by many reasons -

which are not defects in your product. If the battery pack

is only partly discharged it may be re-charged in less than

1 hour. If the battery pack and ambient temperature are

very cold then re-charging may take 1 to 1 1/2 hours. If

the battery pack is very hot it will not re-charge because

the internal temperature safety cut-out will prevent it. If

hot you must remove your battery pack from the char-

ger and allow your battery pack to cool ﬁrst to ambient

temperature and then recharging can be started. If you

charge a second battery pack immediately after the ﬁrst

then the charger can be over-heated. Always allow at

least 15 minutes rest between battery pack charging.

5. REASONS FOR DIFFERENT BATTERY PACK

WORKING TIMES

Charging time problems, as above, and having not used

a battery pack for a prolonged time will reduce the bat-

tery pack working time. This can be corrected after sev-

eral charge and discharge cycles by charging & working

with your saw. Do not re-charge your battery pack below

36OF and above 95OF (2OC and above 35OC) as this will

affect performance.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for better and safer perfor-

mance. Follow instructions for lubricating and changing

accessories. Inspect tool cords periodically and if dam-

aged, have repaired by authorized service facility.

Your power tool requires no additional lubrication or

maintenance. There are no user serviceable parts in

your power tool. Never use water or chemical cleaners

to clean your power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place. Keep the

motor ventilation slots clean. Keep all working controls

free of dust. If you see some sparks ﬂashing in the ven-

tilation slots, this is normal and will not damage your

power tool.

Fig 7.1

Fig 7.2

NA-WT525-M-050727.indd 14 2005-7-27 17:46:08

Cordless Circular Saw WT525

1514

WARRANTY

LIMITED 60-DAY EXCHANGE POLICY

During the ﬁrst 60 days after date of purchase, you may

exchange a tool which does not work properly due to

defects in materials or workmanship by returning the

power tool to the retailer where it was purchased. To

receive a replacement power tool, you must present a

dated proof of purchase and return all original equip-

ment packaged with the original product.

LIMITED TWO YEAR WARRANTY

The manufacturer warrants that, for a period of 2 years

from the date of purchase, this product shall be free of

defects in materials and workmanship. We will repair

or replace, at our option, this tool during the warranty

period, and we may require that the tool be sent postage

prepaid to an approved service center with all original

equipment and a dated proof of purchase. Any replace-

ment or repaired power tool will only be covered by the

limited warranty for the balance of the warranty period

from the date of the original purchase.

WHAT IS NOT COVERED

This warranty applies only to the original purchaser at

retail and is not transferable.

This warranty does NOT cover service or replacement of

parts resulting from normal wear.

This warranty does NOT cover accessories or battery

packs.

This warranty does NOT cover malfunction, failure or

defects due to:

- abnormal use, abuse, neglect, or use not in accordance

with the operations manual

- damage resulting from accidents, drops or mishan-

dling of the tool

- alteration or repairs by other than approved service

centers

- commercial or rental use.

The manufacturer makes no warranties, representa-

tions or promises as to the quality or performance of its

power tools other than those speciﬁcally stated in this

warranty.

FOR SERVICE

Contact our toll-free consumer service line at 1-866-354-

WORX (9679) (Mon.- Sat. 9am to 9pm EST) to receive a

replacement tool or to be directed to an approved ser-

vice center. When you make a warranty claim or send

the tool for warranty service, you must also include a

dated proof of purchase.

NA-WT525-M-050727.indd 15 2005-7-27 17:46:09

Cordless Circular Saw WT525

ADDITIONAL LIMITATIONS

This warranty is only valid for products purchased and

used in the United States of America, its territories or

Canada. Any implied warranty granted under state law,

including warranties of merchantability or ﬁtness for a

particular purpose, are limited to two years from the

date of purchase. The manufacturer is not responsible

for direct, indirect, incidental or consequential damages

including, but not limited to, liability for loss of income

arising from the purchase or use of the product. Some

states and provinces do not allow limitations on how

long an implied warranty lasts and/or do not allow the

exclusion or limitation of incidental damages, so the

above limitations and exclusions may not apply to you.

This warranty gives you speciﬁc legal rights, and you

may also have other rights which vary from state to state

or province to province.

The manufacturer declines any responsibility in regards

to civil liability arising from abusive use or not in confor-

mity with proper use and maintenance of the machine

as described in the operator’s manual.

After the purchase, the manufacturer recommends

proper maintenance of the machine and to read

the operator’s manual before using the machine.

1716

NA-WT525-M-050727.indd 16 2005-7-27 17:46:09

1716

NA-WT525-M-050727.indd 17 2005-7-27 17:46:10

Scie Circulaire Sans Cordon WT525

1918

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT! Lisez et assimilez toutes les instructions. Le non-respect des instruc-

tions ci-après peut entraîner un risque de choc électrique, d’incendie et/ou de blessures

graves.

CONSERVEZ CES INSTRUCTIONS

1. AIRE DE TRAVAIL

a) Veillez à ce que l’aire de travail soit propre et bien éclairée. Le désordre et le manque de

lumière favorisent les accidents.

b) N’utilisez pas d’outils électriques dans un milieu présentant un risque d’explosion, par

exemple en présence de liquides, de gaz ou de poussières inﬂammables. Les outils élec-

triques créent des étincelles qui pourraient enﬂammer les poussières ou les vapeurs.

c) Gardez à distance les curieux, les enfants et les visiteurs lorsque vous travaillez

avec un outil électrique. Ils pourraient vous distraire et vous faire faire une fausse ma-

noeuvre.

2. SÉCURITÉ ÉLECTRIQUE

a) Un outil à pile avec piles incorporées ou un bloc-pile distinct doit être rechargé

uniquement avec le chargeur indiqué pour la pile. Un chargeur qui peut être adéquat

pour un type de pile peut créer un risque d’incendie lorsqu’il est utilisé avec une autre pile.

b) Utiliser un outil à pile uniquement avec le bloc-pile désigné spéciﬁquement.

L’emploi de toute autre pile peut créer un risque d’incendie.

3. SÉCURITÉ DES PERSONNES

a) Restez alerte, concentrez-vous sur votre travail et faites preuve de bon sens.

N’utilisez pas un outil électrique si vous êtes fatigué ou sous l’inﬂuence de

drogues, d’alcool ou de médicaments. Un instant d’inattention lors de l’utilisation

d’outils électriques peut entraîner des blessures graves.

b) Habillez-vous convenablement. Ne portez ni vêtements ﬂottants ni bijoux. Conﬁ-

nez les cheveux longs. Gardez les cheveux, les vêtements et les gants éloignés des pièces

en mouvement. Les vêtements ﬂottants, les bijoux ou les cheveux longs risquent d’être hap-

pés par des pièces en mouvement. Gardez les poignées sèches, propres et exemptes d’huile

et de graisse. Le port de gants en caoutchouc et de chaussures à semelle antidérapante est

recommandé si vous travaillez à l’extérieur.

c) Évitez les démarrages accidentels. Avant d’insérer la pile dans l’outil, assurez-

vous que sa détente est á la position “OFF” (Arrêt) ou verrouillée. Le fait de trans-

porter un outil avec le doigt sur la détente/l’interrupteur ou d’insérer la batterie dans un outil

dont la détente est á la position << ON >> (Marche) peut causer un accident.

d) Retirez les clés de réglage. Prenez l’habitude de vériﬁer si les clés de réglage et autres

outils sont retirés de l’outil avant de le mettre en marche.

e) Ne vous penchez pas trop en avant. Maintenez un bon appui et restez en équilibre

en tout temps. Une bonne stabilité vous permet de mieux réagir à une situation inatten-

due.

f) Utilisez des accessoires de sécurité. Portez toujours une protection oculaire. Selon

les conditions, portez aussi un masque antipoussière, des bottes de sécurité antidérapantes,

un casque protecteur et une protection antibruit.

g) Tenez les mains à l’écart des arrêtes tranchantes et des pièces en mouvement.

h) Si un sac de récupération de poussière et port pour aspirateur est fourni, assurez

vous qu’il est correctement relié et utilisé de façon appropriée. L’utilisation de ce

système réduit les dangers physiques et physiologiques liés à la poussière.

NA-WT525-M-050727.indd 18 2005-7-27 17:46:10

Scie Circulaire Sans Cordon WT525

Scie Circulaire Sans Cordon WT525 Scie Circulaire Sans Cordon WT525

1918

4. UTILISATION ET ENTRETIEN DE L’OUTIL

a) Immobilisez le matériau travaillé sur une surface stable au moyen de serre-joints

ou de toute autre façon adéquate. Le fait de tenir la pièce avec la main ou contre votre

corps n’offre pas une stabilité insufﬁsante et peut entraîner une perte de contrôle de l’outil.

b) Ne forcez pas l’outil. Utilisez l’outil approprié à la tâche. L’outil approprié fonctionne

mieux et de façon plus sécuritaire. Respectez aussi la vitesse de travail qui lui est propre. Un

usage excessif, en plus de fatiguer l’utilisateur, augmentera l’usure de l’outil et rendra son

maniement plus difﬁcile.

c) N’utilisez pas un outil si l’interrupteur ne le met pas en marche ou ne peut l’arrêter.

Un outil qui ne peut être contrôlé par l’interrupteur est dangereux et doit être réparé.

d) Débranchez le bloc-pile de l’outil ou mettez son commutateur en position << OFF

>> (Arrêt) ou <<LOCKED>> (Verrouillé) avant d’effectuer un réglage, de changer

d’accessoire ou de ranger l’outil. De telles mesures de sécurité préventive réduisent le

risque de démarrage accidentel de l’outil.

e) Rangez les outils hors de la portée des enfants et d’autres personnes inexpéri-

mentées. Les outils sont dangereux dans les mains d’utilisateurs novices.

f) Lorsque le bloc-pile n’est pas en usage, tenez-le à l’écart d’autres objets métal-

liques tels que trombones, pièces de monnaie, clés, clous, vis ou autres petits

objets métalliques susceptibles d’établir une connexion d’une borne à une autre.

Le court-circuitage des bornes de batterie peut causer des étincelles, des brûlures, une ex-

plosion ou un incendie.

g) Prenez soin de bien entretenir les outils. Les outils de coupe doivent être toujours

bien affûtés et propres. Des outils bien entretenus, dont les arrêtes sont bien tranchantes,

sont moins susceptibles de se coincer et plus faciles à contrôler.

h) Soyez attentif à tout désalignement ou coincement des pièces en mouvement,

à tout bris ou à toute autre condition préjudiciable au bon fonctionnement de

l’outil. Si vous constatez qu’un outil est endommagé, faites-le réparer avant de

vous en servir. De nombreux accidents sont causés par des outils en mauvais état.

i) Utilisez seulement les accessoires recommandés par le fabricant de votre modèle.

Certains accessoires peuvent convenir à un outil, mais être dangereux avec un autre.

j) Utilisez l’outil approprié à la tâche à accomplir. Ne forcez pas l’outil ni l’accessoire en

tentant d’effectuer une tâche pour laquelle ils n’ont pas été conçus.

5. ENTRETIEN

a) L’entretien ou la réparation de l’outil doit être réalisé seulement par du personnel qualiﬁé.

L’entretien ou la réparation d’un outil électrique, effectués par un amateur, peuvent avoir des

conséquences graves.

b) Pour l’entretien d’un outil, n’employez que des pièces de rechange identiques. Suivez les

directives fournies dans la section <<Entretien>> du présent manuel. L’emploi de pièces

non autorisées ou le non-respect des instructions d’entretien peut créer un risque de choc

électrique ou de blessures.

RÉGLES DE SÉCURITÉ SUPPLÉMENTAIRES POUR SCIES

CIRCULAIRE SANS CORDON

AVERTISSEMENT! La non observance de ces règles peut conduire à des blessures

graves.

1) Lors de l’exécution d’une opération au cours de laquelle l’outil de coupe peut venir

en contact avec les ﬁls cachés ou son propre cordon, tenez l’outil par ses surfaces

NA-WT525-M-050727.indd 19 2005-7-27 17:46:11

Scie Circulaire Sans Cordon WT525

2120

isolées de préhension. Le contact avec un ﬁl sous tension rendra les pièces métalliques

exposées de l’outil sous tension et causera des chocs à l’opérateur.

2) Gardez les mains à l’écart de la zone de coupe. Ne placez surtout pas la main sous le

matériau que vous coupez. Il est impossible de déterminer exactement la proximité de la lame

de votre main.

3) Portez toujours des lunettes à coques latérales ou des lunettes de protection en

utilisant cet outil. Utilisez un respirateur ou un masque anti-poussières pour les

applications produisant de la poussière.

4) N’utiliser pas de lames émoussées ou endommagées. Les lames bien affûtées scient

mieux et améliorent la sécurité. Les lames pliées peuvent aisément se fracturer ou causer un

rebond.

5) La base doit être maintenue fermement contre le matériau à couper aﬁn de réduire

les vibrations de la scie, les sauts et cassures de lame.

6) N’arrêtez jamais la scie de coupe par pression latérale sur la lame.

7) Ne retirez la scie de la pièce travaillée que lorsque la lame s’est arrêtée.

8) En travaillant, ne mettez pas vos mains sous la pièce; le garde ne protège pas de la

lame en dessous de l’ouvrage.

9) La scie circulaire est un outil à main, ne pas la ﬁxer.

10) Avant la coupe, vériﬁer que la ligne de coupe est dépourvue de clous, vis, etc.

11) Ne pas couper de petites pièces avec la scie circulaire. Utiliser plutôt une scie sau-

teuse.

12) N’utilisez que des lames dont la vitesse nominale de rotation dépasse la vitesse à

vide de la scie.

13) Ne jamais enlever le système de capot protecteur. Ne jamais utiliser la scie si le sys-

tème de capot protecteur ne fonctionne pas correctement. Ne jamais verrouiller le capot mo-

bile sur la position ouverte. Le capot doit bouger librement.

14) Avant chaque emploi, vériﬁez TOUJOURS si le garde-lame inférieur se ferme cor-

rectement. N’utilisez pas la scie si le garde-lame inférieur ne pivote pas librement

et ne se ferme pas instantanément. Ne ﬁxez/attachez jamais le garde-lame inférieur en

position ouverte. Si vous échappez accidentellement a scie, le garde-lame inférieur peut se

tordre. Relevez le avec le levier de rétraction. Assurez-vous que le garde se déplace librement

et qu’il ne touche pas la lame ni aucune autre pièce sous tout angle et profondeur de coupe.

15) Toujours vériﬁer les murs, sols et plafonds aﬁn de voir s’il existe des câbles et

tuyaux cachés.

16) Ne pas couper de matériaux contenant de l’amiante.

17) Ne pas utiliser des lames pour métal ou pierre. Utiliser uniquement des lames pour

bois.

18) Ne pas utiliser la scie circulaire pour couper des branches d’arbre ou des bûches.

19) Ne pas utiliser de meules.

20) Positionnez vous d’un côté ou de l’autre de la scie et non directement derrière

celle-ci. Un saisissement de lame pourrait projeter l’outil vers l’arrière.

21) Rappelez vous que cet outil est toujours en état de fonctionnement possible parce

qu’il ne doit pas être branché dans une prise de courant.

22) Sortez le bloc pile de l’outil ou placez son commutateur en position << OFF >> (Ar-

rêt) ou <<LOCKED>> (Verrouillé) avant d’y faire un travail quelconque, d’effectuer un

réglage ou de changer d’accessoire. Une telle mesure de sécurité préventive préviendra le

démarrage accidentel de l’outil.

23) Conservez ces instructions. Reportez-vous y fréquemment et utilisez-les pour informer

d’autres personnes qui pourraient utiliser cet outil. Si une autre personne utilise cet outil, as-

surez-vous de lui fournir ces instructions.

NA-WT525-M-050727.indd 20 2005-7-27 17:46:11

La page charge ...

WORX Tools Chainsaw WT525 Manuel utilisateur

Ce manuel convient également à

WORX Tools Chainsaw WT525 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents