Maytag CES3760AAQ Manuel utilisateur

Marque: Maytag

Modèle: CES3760AAQ

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!i!i!i!ii!ii!i!!ii!iiiiiiiiii!i_ii_iii_

iii i i

Electric S|ide-|. Smoo_h_op -

Sasy Touch Co._ro| 500

Table of Contents

important Safety instructions ................. 1=3

Care & Cleaning ......................................... 4-7

Self-Clean Oven

Cleaning Procedures

Maintenance ............................................... 7=8

Oven Window

Oven Light

Troubleshooting ...................................... 9-10

Surface Cooking ................................... 11-13

Surface Controls

Smoothtop Surface

Oven Cooking ........................................ 14-20

Baking Broiling

Cook & Hold Sabbath Mode

Delay Cook & Hold Oven Racks

Keep Warm

Warranty & Service ..................................... 21

Guide d'utUisation et d'entretien ............. 22

Guia de uso y cuidado ............................... 46

Form No. A/01/06 Part No. 8113P610-60 @2006 Maytag Appliances Sales Co. Litho U.S.A.

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer.

Always disconnect power to appliance before servicing.

por a l$afe

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance must

be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service, or

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or

Smoke Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot.

To prevent grease fires, do not let cooking grease or

other flammable materials accumulate in or near the

appliance.

|n Case of Fire

Use dry chemical or foam-type extinguisher or baking

soda to smother fire or flame. Never use water on a

grease fire.

1. Turn off appliance to avoid spreading the flame.

2. NEVER pick up or move a flaming pan.

3. Smother fire or flame by closing the oven door.

Turn off ventilating hood to avoid spreading the flame.

Extinguish flame then turn on hood to remove smoke

and odor.

Child Safety

Do not use the cooktop or oven as a storage area for food

or cooking utensils.

NEVER leave children alone or unsupervised near the

appliance when it is in use or isstill hot. Children should

never be allowed to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in

it can be hot. Let hot utensils cool in a safe place, out of

reach of small children. Children should be taught that an

appliance is not a toy. Children should not be allowed to

play with controls or other parts of the appliance.

About Your Appliance

To prevent potential hazard to the user and damage to the

appliance, do not use appliance as a space heater to heat

or warm a room. Also, do not use the oven as a storage

area for food or cooking utensils.

Do not obstruct the flow of air by blocking the oven vent.

the oven vent is located at the rear of the cooking surface.

DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even

though they are dark in color. Interior surfaces of any oven

become hot enough to cause burns. During and after use,

do not touch, or let clothing or other flammable materials

contact heating elements or interior surfaces of oven until

they have had sufficient time to cool. Other surfaces of the

appliance may become hot enough to cause burns -

among these surfaces are: oven vent opening and surface

near this opening, oven door, window of oven door.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Cooking Safety

NEVER heat an unopened food container in the oven.

Pressure build-up may cause container to burst resulting

in serious personal injury or damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes should

never be used as potholders because they can trail across

hot elements and ignite or get caught on appliance parts.

Wear proper apparel. Loose fitting or long hanging-

sleeved apparel should not be worn while cooking.

Clothing may ignite and cause burns if garment comes in

contact with heating elements.

Always place oven racks in the desired positions while

oven iscool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be moved

while hot, use a dry potholder. Do not let potholder

contact hot element in oven.

Use racks only in the oven in which they were shipped/

purchased.

Use care when opening the oven door. Let hot air or steam

escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer's instructions. If a plastic frozen food con-

tainer and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

Do not allow aluminum foil or meat probe to contact

heating element.

Always turn off all controls when cooking is completed.

Utensil Safety

Follow the manufacturer's directions when using oven

cooking bags.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices or

accessories that are not specifically recommended in this

guide. Do not use add-on oven convection systems. The

use of devices or accessories that are not expressly

recommended in this guide can create serious safety

hazards, result in performance problems, and reduce the

life of the components of the appliance.

If pan is smaller than element, a portion of the element

will be exposed to direct contact and could ignite clothing

or potholder.

Cont.

ImportentSefetv

Only certain types of glass, glass/ceramic, ceramic,

earthenware, or other glazed utensils are suitable for

cooktop or oven service without breaking due to the

sudden change in temperature. Follow utensil

manufacturer's instructions when using glass.

Turn pan handle toward center of cooktop, not out into

the room or over another surface element. This reduces

the risk of burns, ignition of flammable materials, or

spillage if pan is accidently bumped or reached by small

children.

Cooktop

NEVER leave surface units unattended, especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different sized surface

elements. Select pans with flat bottoms large enough to

cover element. Fitting pan size to element will improve

cooking efficiency.

GLASS=CEPJtMIC SURFACE: NEVER cook on a broken

cooktop. If cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and create a

risk of electric shock. Contact a qualified technician

immediately.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease

or other flammable materials from accumulating on hood

or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and wait

for appliance parts to cool before touching or cleaning.

Clean with caution. Use care to avoid steam burns if a wet

sponge or cloth is used to wipe spills on a hot surface.

Some cleaners can produce noxious fumes if applied to a

hot surface.

Clean only parts listed in this guide.

Self-Clean Oven

Do not clean door gasket. The door gasket isessential

for a good seal. Care should be taken not to rub, damage,

or move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

Important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/or

door in the room where the appliance is located during

the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a very

sensitive respiratory system. Fumes released during an

oven self-cleaning cycle may be harmful or fatal to birds.

Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These Instructions for Future Reference

Cleanln

Self-Clean Oven

To set Self=Clean:

Important: Oven temperature must be below 400° Fto

program a clean cycle.

1. Close the oven door.

2. Move door lock lever right to the locked position.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

Remove all pans and oven racks from the oven. The oven

racks will discolor and may not slide easily after a self-

clean cycle ifthey are not removed.

Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket isthe seal around the oven door and

window).

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket isdesigned to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

isacid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-clean

cycle.

3. Pressthe CLEAN pad. CLEAN

, CLEAN flashes in the display.

4. Pressthe A or V pad.

, CUM (Clean - Medium Soil) is displayed.

If the door isnot closed, beeps will sound and \ _,

"door" will display. If the door is not closed

within 45 seconds, the self-cleaning operation will be

canceled and the display will return to the time of day.

Pressthe A or Y pad to scroll through the

self-cleaning settings.

CUH (Clean - Heavy Soil, 4 hours)

CUM (Clean - Medium Soil, 3 hours)

, CUL (Clean - Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, the oven will start cleaning.

The cleaning time will start counting down in the display.

LOCKwill appear in the display.

CLEAN will appear in the display.

To Delay a Self=Clean Cycle:

1. Pressthe DELAY pad.

, DELAY flashes.

, 00:00 will appear in the display.

Pressthe A or V pad to set the amount of time

you want to delay the cycle. Delay time can be

set from ten minutes (00:10) to 11 hours, 59

minutes (11:59).

3. While DELAY is flashing, press the CLEAN pad.

, CLEAN will flash.

4. Pressthe A or V pad.

, CUM (Clean - Medium Soil) is displayed.

DELAY

CLEAN

Cont.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

¢leanin

5. Press the A or V pad to scroll through the self-cleaning

settings.

, CUH (Clean - Heavy Soil, 4 hours:)

CUM (Clean - Medium Soil, 3 hours:)

CUL (Clean - Light Soil, 2 hours:)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, CLEAN, DELAY and LOCKwill appear

in the display to show that the oven is set for a delayed

clean operation. The delay time is displayed.

DELAY

if the oven has already been set for a clean

cycle and you wish to set a delay:

1. Press the DELAY pad.

, DELAY flashes.

, 00:00 will appear in the display.

2. Press the A or V pad to set the amount of time

you want to delay the cycle.

After four seconds, CLEAN, DELAY and LOCK

will appear in the display to show that the oven \,_,_"

is set for a delayed clean operation.

The delay time is displayed.

When the Self-Clean cycle starts:

, DELAY will turn off.

The clean time will appear in the display.

To cancel the Self-Clean cycle:

Press the CANCEL pad.

, All words disappear from the display.

, All functions are canceled.

The time of day appears in the display.

CANCEL

During the Self=Clean Cycle

When LOCK shows in the display, the door cannot be opened.

To prevent damage to the door, do not force the door open

when LOCK isdisplayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

After Self=Cleaning

About one hour after the end of the self-clean cycle, LOCK

will turn off. The door can then be opened. Move door lock

lever to the left to unlock.

Some soil may leave a light gray, powdery ash. Remove

itwith a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re-

moved during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This isnormal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect perfor-

mance.

Notes:

, If the oven door isleft open, "door" will flash in the

display and a signal will beep until the door is closed

and the CLEAN pad is pressed again.

, If more than five seconds elapse between pressing the

CLEAN pad and the A or Y pad, the program will

automatically return to the previous display.

, The oven door will be damaged if the oven door is

forced to open when LOCK is still displayed.

Cleaning Procedures

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-877-232-6771 U.S.A.and

1-800-688-8408 Canada.

Cooktop -

Porcelain Enamel

Clock and

Control Pad

Area

Control Knobs

Cooktop -

Glass=Ceramic

Oven Window

and Door = Glass

Porcelain enamel is glass fused on metal and may crack or chip with misuse. It isacid-resistant, not acid-

proof. All spillovers, especially acidic or sugary spillovers, should bewiped up immediatelywith adry cloth.

* When cool, wash with soapy water, rinse and dry.

* Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

* Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

* To activate control lock for cleaning, see Locking the Controls, page 15.

* Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the surface.

* Glass cleaners may be used if sprayed on a cloth first. DO NOTspray directly on centre/pad and

display area.

* Remove knobs in the OFF position by pulling forward.

* Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

* Turn on each element to be sure the knobs have been correctly replaced.

Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.

important: Call an authorized servicer if the glass=ceramic top should crack, break or if metal or

aluminum foil should melt on the cooktop.

* Allow the cooktop to cool before cleaning.

* General ==Cleancooktop after each use,orwhen needed, with adamp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001:)**.Then, buff with a clean dry cloth.

Important: Permanent stains will develop ff softis allowed to cook on by repeatedly using the cooktop

when soiled.

* Heavy Soils or Metal Marks -- Dampen a "scratchless" or "never scratch" scrubber sponge. Apply

Cooktop Cleaning Creme* (Part No. 20000001:)**and scrub to remove as much soil as possible. Apply a

thin layer of the creme over the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3

hours for very heavy soil:).Keep moist by covering the paper towel with plastic wrap. Scrub again, then

buff with a clean, dry cloth.

important: Onlyuse a CLEAN,DAMP "scratchless"pad that is safe for non-stick cookware. Thepattern and

glass will be damaged if the pad is not damp, if thepad is soiled, orif another type of pad is used.

* Burned-on or Crusty Soils ==Scrub with a "scratchiess" or "never scratch" scouring pad and Cooktop

Cleaning Creme*.

Important: Hold a razor blade scraper at 30° angle and scrape any remaining soil. Then clean as

described above. Do not use the razor blade for daily cleaning as it may wear the pattern on _ _

the glass. _ _9_

, Melted Sugar or Plastic ==Immediately turn element to LOW and scrape sugar or !A_

p astcfromhotsurface to acoo area ThenturneementOFFanda owtocoo Cean _

residue with razorblade scraper and Cooktop Cleaning Creme* (PartNo. 20000001:)**. d

* Avoid using excessive amounts of water which may seep under or behind glass, causing staining.

* Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a

cloth first.

* Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will

scratch glass.

Cont.

Cleanin9

Oven Interior . Follow instructions on page 4-5 to set a self-clean cycle.

Oven Racks * Clean with soapy water.

Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

Rackswill permanently discolor and may not slide smoothly if left inthe oven during aself-clean operation.

If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

Stainless Steel * DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

(select models) * DO NOT USEABRASIVE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil ==Wipe with one ofthe following - soapywater, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

• Moderate/Heavy Soil == Wipe with one of the following - Don Ami*, Smart Cleanser*, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinseand dry. Torestore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

• Discoloration == Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediatelyand dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

Storage Drawer, * When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp

Door Handle = cloth as this may damage the surface and may cause a steam burn.

Painted Enamel * F_rstubb_rns_i__usemi_d_yabrasivec_eaningagentssuchasbakings_dapaste_rB_nAmi.*D_n_tuse

abrasive, caustic or harsh cleaning agents such as steel wool pads or oven cleaners. These products will

scratch or permanently damage the surface.

Important: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface

may discolor or dull if soil is not immediately removed. Thisis especially important for

white surfaces.

• Brand names for cleaning products are registered trademarks of the respective manufacturers.

•* To order direct, call 1-877-232-6771 U.S.A. and 1-800-688-8408 Canada.

Meintenence

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or

other objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

itsstructure causing an increased risk of breakage at a later

date.

Cont.

Oven Door

4. Replace bulb cover and secure with wire retainer.

5. Reconnect power to range. Reset clock.

Use a dry potholder and very carefully unscrew bulb cover

and bulb.

Replace with a 40-watt, oven-rated appliance bulb. Bulb

with a brass base is recommended to prevent fusing of

bulb into socket.

Replace bulb cover and reconnect power to oven.

Resetclock.

To remove:

1. When cool, open the oven door to the

first stop position (about four inches).

2. Grasp door at each side. De net use

the door handle to lift door.

3. Lift up evenly until door clears hinge arms.

To replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges.

Door sheuld net appear crooked.

Important: The oven door on a new range may feel "spongy"

when it isclosed. This isnormal and will decrease with use.

Leveling Legs

Be sure the range isleveled when installed.

ifthe range is not level, turn the leveling legs,

located at each corner of the range, until

range is level.

Storage Drawer

ANTI-TIP BRACKET

LEVELING LEG

Oven Light (style varies by model)

To replace oven light bulb:

1. When oven is cool, hold bulb cover

inplace, then slide wire retainer

off cover. Important: Bulb

cover will fall if not held in

place while removing wire

retainer.

2. Remove bulb cover and light

bulb.

3. Replace with a 40-watt appliance bulb.

BULBCOVER

RETAINER

The storage drawer can be removed to allow you to clean

under the range.

To remove:

1. Empty drawer and pull out to the first stop position.

2. Lift up the front of the drawer.

3. Pull out to the second stop position.

4. Grasp sides and lift drawer up and out.

To replace:

1. Fit the ends of the drawer glides into the rails in the range.

2. Lift up the front of the drawer and gently push in to the

first stop position.

3. Lift drawer up again and push until drawer is closed.

Troubleshoodn9

For most concerns, try these first.

Part or all of appliance does

not work.

Clock, indicator words, and/or

lights operate but oven does

not heat.

Baking results are not as

expected or differ from

previous oven.

Food is not broiling properly or

smokes excessively.

Oven will not self=clean.

Oven did not clean properly.

Oven door will not unlock after

self=clean cycle.

Check

if oven controls have been properly set.

to be sure plug is securely inserted into receptacle.

or re-set circuit breaker. Check or replace fuse.

power supply.

Check

if surface and/or oven controls have been properly set. See pages 11 & 15.

if oven door is unlocked after self-clean cycle. See page 5.

if oven is set for a delayed cook or clean program. See pages 16,4 & 5.

if Control Lock is activated. See page 15.

if control is in Sabbath Mode. See page 19.

, Oven may be set for a Cook & Hold or Delay function.

, The Control Lock may have been set.See page 15.

Make sure the oven vent has not been blocked. See page 20 for location.

Check to make sure range is level.

Temperatures often vary between a new oven and an old one.As ovens age,the oven

temperature often "drifts" and may become hotter or cooler. See page 19 for

instructionson adjusting the oven temperature. Important: It is not recommended

to adjust the temperature if only one or two recipes are in question.

, Check oven rack positions. Food may be too close to element.

, Broil element was not preheated.

, Aluminum foil was incorrectly used. Never line the broiler insertwith foil.

, Oven doorwas closed during broiling. Leavethe door open to the first stop position

(about 4 inches_).

, Trim excess fat from meat before broiling.

, A soiled broiler pan was used.

, Voltage in house may be low.

, Check to make sure the cycle is not set for a delayed start. See pages 4-5.

Check if door isclosed.

Check if control is inSabbath Mode. See page 19.

Oven may be over 400° F. Oven temperature must be below 400° Fto program a

clean cycle.

, Longer cleaning time may be needed.

, Excessive spillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

, Oven interior is still hot. Allow about one hour for the oven to cool after the

completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

, The control and door may be locked. See page 5.

Smoothtop surface

shows wear.

Moisture collects on oven

window or steam comes from

oven vent.

There is a strong odor or light

smoke when oven is turned on.

Fault Codes

Noises may be heard.

There are no beeps and

no display.

SAb flashing and then

displayed continuously.

* Tinyscratches or abrasions.

- Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans

across top. Make sure pan bottom isnot rough. Use the recommended

cleaning agents. See page 6.

* Metal marks.

- Do not slide metal pans across top. When cool, clean with Cooktop

Cleaning Creme (Part No. 20000001)*. See page 6.

* Brown streaks and specks.

- Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure

cooktop and pan bottom are clean.

* Areas with a metallic sheen.

- Mineral deposits from water and food. Use recommended cleaning agents.

See page 6.

* Pitting or flaking.

- Remove sugary boilovers promptly. See page 6.

* This is normal when cooking foods high in moisture.

* Excessivemoisture was used when cleaning the window.

* This isnormal for a new range and will disappear after a few uses. Initiating a clean

cycle will "burn off" the odors more quickly.

* Turning on aventilation fan will help remove the smoke and/or odor.

* Excessivefood soils on the oven bottom. Use a self-clean cycle.

* BAKE or LOCK may flash rapidly in the display to alert you if there is an error

or a problem. If BAKE or LOCK appear in the display, press CANCEL pad.

If BAKE or LOCKcontinue to flash, disconnect power to the appliance.

Wait a few minutes, and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized servicer.

* If the oven is heavily soiled, excessive fiareups may result in a fault code during

cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out

excess soil, then reset the clean cycle. If the fault code reappears, contact an

authorized servicer.

* The oven makes several low-level noises.You may hear the oven relays asthey go on

and off. This isnormal.

* As the oven heats and cools, you may hear sounds of metal parts expanding and

contracting. This isnormal and will not damage your appliance.

* A fan sound can be heard. This isthe cooling fan and isnormal. The fan will

continue to run after use until the oven cools.

* Oven may be in Sabbath Mode. Seepage 19.

* Control may be locked. See page 15.

* Oven is in Sabbath Mode. To cancel, press and hold the CLOCK pad for

five seconds.

To order direct, call 1-877-232-6771 U.S.A. and 1-800-688-8408 Canada.

SurfeceCookin9

Surface Controls

Use to turn on the surface elements. An infinitechoice of

heat settings isavailable from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

The control panel is marked to identify which

element the knob controls. Forexample, the

graphic at right indicates left front element.

®0

3. There isan element indicator light on the control panel.

When any surface control knob isturned on, the light will

turn on.The light will turn off when all the surface

elements are turned off.

When a control isturned on, a glow can be seen through

the smoothtop surface. The element will cycle on and off

to maintain the preset heat setting, even on High.

4. After cooking, turn knob to OFF. Remove pan.

Suggested Heat Settings

The size and type of cookware, type and amount of food

being heated, and wattage of individual elements will

determine where to set the knob for cooking operations.

Some elements have a predetermined simmer and melt

setting that will require only minor adjustment up or down

depending on the food being prepared. The other elements

have settings printed around the knobs that are also unique

to those elements. Adjust the heat settings to the numbers

that give the desired cooking results. The following

descriptions will aid in choosing the settings that will give

optimum results.

Hold or Warm: Food maintains a temperature above 140° F

without continuing to cook. Food isinitially hot and then heat

isreduced. Never use a hold or warm setting to reheat cold

food.

Simmer: Food forms bubbles that barely break the

surface. Foods are between 185° Fand 200° F.A simmer

setting can also be used to steam or poach foods or continue

cooking covered foods.

Slow Boil: Food forms bubbles at a moderate pace. A slow

boil setting can also be used for most frying and for

maintaining the cooking of large amounts of liquids.

Boil: Liquid forms bubbles at a rapid pace.A fast boil setting

can also be used to brown meat, stir fry, saute, and heat oil

for frying before turning to a lower setting. The highest 3 or 4

settings on the knob are used for these cooking

operations. The highest setting isalways used to bring water

to a boil. Some elements offer an even higher speed for

boiling liquids.

Srnoothtop Surface

Notes:

Cooktop may emit light smoke and odor the first few

times the cooktop is used. This isnormal.

, Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food iscompletely cooked and use

the retained heat to complete cooking. When the hot

surface light turns off, the cooking area will be cool

enough to touch. Because of the way they retain heat, the

smoothtop elements will not respond to changes in

settings as quickly as coil elements.

, In the event of a potential boilover, remove the pan from

the cooking surface.

, Never attempt to lift the cooktop.

The smoothtop surface may appear discolored when it is

hot. This isnormal and will disappear when the surface

cools.

Cooking Areas

The cooking areas on your range are identified by permanent

circles on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend more than !/2 to 1=inch beyond

the cooking area.

When a control isturned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on High.

For more informationon cookware, refer to Cookware

Recommendations on page 13.

9" SINGLE

6" SINGLE

ELEMENT 6" SINGLE ELEMENT

9" SINGLE

ELEMENT

Hot Surface Light

The Hot Surface indicator light islocated at the front of the

cooking surface. The light illuminateswhen any cooking area

is hot. It will remain on, even after the control isturned off,

until the surface has cooled.

Tips to Protect the

Srnoothtop Surface

Cleaning ([seepage 6 for more information,)

, Before first use, clean the cooktop.

, Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

, If a spillover occurs while cooking, immediatelyclean the

spill from the cooking area while it ishot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean, dry towel.

, Do not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

, Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

, Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

* Do not use glass pans. They may scratch the surface.

, Never place a trivet or wok ring between the surface and

pan. These itemscan mark or etch the top.

, Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. ([See

Cleaning, page 6._)

, Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

, To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area.Wipe

the cooktop surface with a clean cloth or paper towel

before using.

Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

Continuously cooking on a soiled surface may/will result in

a permanent stain.

Cont.

$urfuceCookin

To Prevent Other Damage

* Do not allow plastic, sugar or foods with high sugar

content to melt onto the hot cooktop. Should this happen,

clean immediately.([SeeCleaning, page 6._)

* Never let a pan boil dry as this will damage the surface and

pan.

* Never use cooktop as a work surface or cutting board.

* Never cook food directly on the surface.

* Do not use a small pan on a large element. Not only does

this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning.

* Do not use non-flat specialty itemsthat are oversized or

uneven such as round-bottom woks, rippled bottom and/or

oversized canners and griddles.

* Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized servicer.

Cookware Recommendations

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

To determine whether your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles asthe water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

_,,_,_,_,_t_,,,,_,:,,_;_,_,__;_;;;_;_;;_;_;;_;_;;_;_ _!!__ i,_ ! _!,_ ii_!i_ _i i__ _i;_',_________________, ______,_,,_,,_,_,_,_........

Flat,smooth-bottom Panswith grooved or warped bottoms.

pans. Panswith uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pansthat arethe Panssmaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavyhandles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat-bottom woks. Woks with a ring-stand bottom.

Canning and Oversize

Cookware

All canners and large pots must have flat bottoms and

must be made from heavy=gauge materials. Thisiscritical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer,and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure isreached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. Ifthe heat isnot turned down, the cooktop may be

damaged.

Control Panel

A B

BROIL _,

CLEAN DELAY CLOCK

F G H

TIMER

CANCEL

Thecontrol panelisdesigned for easeinprogramming. Thedisplaywindow on thecontrol shows time ofday,timer and ovenfunctions.

Control panel shown includesmodel specific features. (Styling may vary depending on model.)

iiiiiiiiiiiiiiiiiii_i

BROIL

BAKE

More (A) or

Less (V)

TIMER

COOK& HOLD

CLEAN (select

models)

DELAY

CLOCK

KEEP WARM

CANCEL

Use for broiling and top browning.

Use for baking and roasting.

Enters or changes time, oven

temperature. Sets HI or LObroil.

Sets Timer.

Bakes for a preset time, then holds food

warm for 1 hour.

Use to set self-clean cycle.

Programs the oven to start baking at

a later time.

Use to set time-of-day clock.

Use to keep cooked food warm in oven.

Cancels all operations except Timer

and Clock.

Using the Touchpads

. Pressthe desired pad.

* PressA or Y to enter time or temperature.

. A beep will sound when any pad is touched.

. A double beep will sound if a programming error occurs.

Important: Four seconds after pressing the A or Y pad,

the time or temperature will automatically be entered. If

more than 30 seconds elapse between touching a function

pad and the A or V pad, the function will be canceled and

the display will return to the previous display.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To change the clock to

24=hour format:

1. Press and hold the CANCEL and

BELAY pads for three seconds.

2. Press A or V pad to select 12 or

24 hour.

3. Set the time of day following the

directions below.

-- CANCEL

-- DELAY

To set the Clock:

1. Press the CLOCK pad.

. Colon flashes in the display.

2. Press A or V pad to set the time of day.

. Colon continues flashing.

3. Press the CLOCK pad again or wait four

seconds. The colon stops flashing.

When electrical power is supplied or after a power

CLOCK

interruption,the last clock time before power was interrupted

will flash.

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Delay Cook, Delay Clean or Cook & Hold.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the CANCEL and CLOCK pads for three

seconds. The time of day will disappear from the display.

Cont.

Whentheclockdisplayiscanceled, press the CLOCK pad to

briefly display the time of day.

To restore the Clock display:

Press and hold the CANCEL and CLOCK

pads for three seconds. The time of day

will reappear in the display.

-- CANCEL

--CLOCK

]rimer

The timer can be set from one minute (0:01) up to 99 hours

and 59 minutes (99:59).

The timer can be used independentlyof any other oven

activity. It can also be set while another oven function is

operating.

The timer does not control the oven. It only controls a beeper.

To set the Timer: _,

1. Pressthe TIMER pad. TIMER

,0:00 lights in the display.

The colon will flash.

2. Pressthe A or Y pad until the

correct time appears in the display.

The colon will continue to flash.

3. PressTIMER pad again or wait four seconds.

The colon continues flashing and the time begins

counting down.

The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, one long beep will sound.

To cancel the Timer:

1. Press and hold the TIMER pad for three seconds.

2. Pressthe TIMER pad and set the time to 0:00.

Locking the Controls

The touchpad controls can be lockedfor safety, cleaning, or

to prevent unwanted use. They will not function when locked.

If the oven is currently in use, the controls cannot be locked.

The current time of day will remain in the display when the

controls are locked.

To lock:

Press and hold the CANCEL and COOK &

HOLD pads for three seconds. (Press the

CANCEL pad first.)

To unlock:

Press and hold the CANCEL and COOK &

HOLD pads for three seconds. (Press the CANCEL pad first.)

-- CANCEL

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there isan error or a problem. If BAKE or LOCK flash in the

display, press the CANCEL pad. If BAKE or LOCK continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Bake

To set Bake:

1. Press the BAKE pad.

BAKEwill flash.

000 will light in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 550°.

Press or press and hold the A or Y pad.

350°will light when either pad isfirst pressed.

Pressthe A pad to increase the temperature.

Pressthe V pad to decrease the temperature.

3. Press BAKE pad again or wait four seconds.

BAKE

BAKEwill stop flashing and light in the display.

100° or the actual oven temperature will display. It will

rise in 5 degree increments until the preset temperature

is reached.

4. Allow the oven to preheat for 8-15 minutes.

When the set oven temperature is reached, one long

beep will sound.

To recall the set temperature during preheat, press the

BAKE pad.

5. Placefood in the oven.

6. Check cooking progress at the minimum cooking time.

Cook longer if needed.

7. When cooking is finished, press CANCEL. CANCEL

8. Remove food from the oven. _,_,/

Notes:

, Tochange the oven temperature during cooking, press the

Bake pad, then the A or V pad until the desired tem-

perature is displayed.

Tochange the oven temperature during preheat, press the

Bake pad twice, then press the A or V pad until the

desired temperature is displayed.

If you forget to turn off the oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate this

feature, see page 19.

After one hour in HOLD WARM:

"End" will display.

, The time of day will reappear in the display.

To cancel Cook & Hold at any time:

Press the CANCEL pad. Remove food from oven.

Delay Cook & Hold

CANCEL

Baking Differences Between Your Old

and New Oven

It isnormal to notice some baking time differences between a

new oven and an old one. See Adjusting the Oven Temperature

on page 19.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Press the COOK & HOLD pad.

BAKE and HOLD flash.

999 lights in the display.

2. Select the oven temperature. The oven

temperature can be set from 170° to 559°.

Press or press and hold the A or V pad. \_

Press the A pad to increase the temperature.

Press the V pad to decrease the temperature.

3. Press COOK & HOLD again ORwait four seconds.

HOLD flashes.

99:99flashes in the display.

4. Enter the amount of time you want to bake by pressing the

A or Y pad. Bake time can be set from ten minutes

(99:19) to 11 hours, 59 minutes (11:59).

BAKE and HOLD light in the display.

The baking time will light in the display.

The baking time will start counting down.

When the cooking time has elapsed:

, Four beeps will sound.

, BAKEwill turn off.

, HOLD and WARM will light.

, 179°will display.

When using Delay, the oven begins to cook later inthe day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time.

Delay time can be set from 19 minutes (99:19) to 11 hours, 59

minutes (11:59).

To set a Delayed Cook & Hold cycle:

1. Pressthe DELAY pad.

DELAY flashes.

99:99 flashes in the display.

2. Pressthe A or V pad to set the delay time.

While DELAY is still flashing:

3. Pressthe COOK & HOLD pad.

999 lights in the display.

BAKE and HOLD flash.

4. Press A to set the baking temperature.

99:99 and HOLD flash.

DELAY

" BAKEstays lit.

Press A to set the baking time.

, The Delay time, DELAY, BAKE and HOLD light in

the display.

When the Delay time has expired:

, DELAYwill turn off.

Baking time is displayed.

BAKE and HOLD are displayed.

To set a Delay when Cook & Hold has already

been programmed: _,

1. Press the DELAY pad. DELAY

* DELAY flashes.

00:00 appears in the display.

Cont.

2. Press the A or V pad to set the delay time.

, After four seconds, DELAY will

stay lit to remind you that a delayed

cooking cycle has been set.

When the Delay time has expired

and the oven starts:

, The baking time will be displayed.

, DELAYwill turn off.

, BAKE and HOLD will remain lit.

To cancel:

Press the CANCEL pad.

, All timed and untimed cooking functions

will be canceled.

CANCEL

, The time of day will reappear in the display.

Important:

, DO NOT use delayed baking for itemsthat require a

preheated oven, such as cakes, cookies, and breads.

, Do not use delayed baking if oven isalready hot.

Notes:

, Foroptimal food quality, oven cooked foods should be kept

warm for no longer than 1 to 2 hours.

, To keep foods from drying, cover loosely with foil or a lid.

, To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press KEEPWARM and A pads to set 170° F.

- warm for 12-15 minutes.

To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press KEEPWARM and A pads to set 170° F.

- warm for five minutes, turn off the oven and leave plates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing.

Keep Warm

For safely keeping foods warm or for warming breads

and plates.

To set Keep Warm:

1. Press the KEEPWARM pad.

, WARM flashes.

000 appears in the display.

Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to 190°.

Press or press and hold the A or Y pads.

170° will light when either pad isfirst pressed.

Press the A pad to increase the temperature.

Press the Y pad to decrease the temperature.

WARM and the temperature will be displayed while Keep

Warm isactive.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

CANCEL

Changing Temp °F/°C

1. The factory default setting for temperature is Fahrenheit.

2. To change the setting, press and hold the CANCEL and

BAKE pads at the same time for three seconds.

3. A single beep will sound and the current setting will be

displayed (°F or °C). (if no change is made, the range will

return to the existing setting after 30 seconds.)

4. To change the setting, press the A or T pad. Pressagain to

return to existing setting. Wait five seconds and the setting

will be complete.

To set Broil:

1. Press the BROIL pad. BROIL

* BROIL flashes.

, SEt isdisplayed.

2. Press the A pad to set HI Broil or press the V pad to set

LO Broil.

, HI or LO will be displayed.

, Select HI Broil (550° F) for normal broiling. Select

LO Broil (450° F)for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

, BROIL will remain lit.

For optimum browning, preheat broil element for 3-4

minutes before adding food.

Place food in the oven. Leave oven door open about four

inches(the first stop).

Turn meat once about halfway through cooking.

When food iscooked, press the CANCEL pad.

Removefood and broiler pan from the oven. CANCEL

The time of day will reappear in the display.

Notes:

For best results when broiling, use a pan designed for

broiling.

Expect broil times to increaseand browning to be

slightly lighter if appliance is installedon a 208-volt

circuit.

, HI is used for most broiling. Use LO Broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

, Tochange the oven temperature during broiling, press the

BROIL pad and then press the A or V pad to switch

between LO and HI Broil.

Broil times may be longer when the lower broiling

temperature isselected.

Most foods should be turned halfway through broiling

time.

Broiling Chart

Beef

Steak, 1" thick

Hamburgers, 3/4" thick

Pork

Bacon

Chops, 1"

Ham - precooked slice, 1/2" thick

Poultry

Chicken Pieces

Seafood

Fish Steaks, buttered, 1" thick

Fillets

The top rack position is#5.

3or4

Medium

Well Done

Warm

Well Done

Flaky

15- 18 minutes

19 - 23 minutes

15- 18 minutes

6 - 10 minutes

22 - 26 minutes

8 - 12 minutes

LO Broil

28 - 38 minutes

10 - 15 minutes

8 - 12 minutes

Note: This chart isa suggested guide. The times may vary with the food being cooked.

Automatic Shut-Off/

Sabbath Mode

The oven will automatically turn off after 12 hours ifyou

accidentally leave it on. This safety feature can be turned off.

To cancel the 12-hour shut=off and run the

oven continuously for 72 hours:

1. Set the oven to BAKE (see page 15).

CLOCK

2. Pressand holdtheCLOCK pad forfiveseconds.

SAb will be displayed and flash for five seconds.

SAb will then be displayed continuously until turned

off or until the 72-hour time limit is reached.

BAKE will also be displayed if a bake cycle is in use

while the oven is in Sabbath Mode.

. BAKE is the only function that operates during the

Sabbath Mode. Aft other functions (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press CANCEL pad.

BAKEwill turn off in the display.

No beeps will sound.

To cancel the Sabbath Mode:

1. Pressthe CLOCK pad for five seconds.

2. After 72 hours, the Sabbath Mode will end.

SAb will flash for five seconds.

CANCEL

CLOCK

The time of day will return to the display.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25 degrees

higher or lower than your recipe recommends, then bake.

The results of the "test" should give you an idea of how much

to adjust the temperature.

To adjust the oven temperature:

1. Press BAKE.

2. Enter 550° by pressing the A pad.

3. Press and hold the BAKE pad for several

seconds or until 0° appears in the display.

BAKE

If the oven temperature was previously adjusted,

the change will be displayed. For example, if the oven

temperature was reduced by 15 degrees the display

will show-15 °.

4. Press the A or V pad to adjust the temperature.

Eachtime a pad is pressed, the temperature changes by 5

degrees. The oven temperature can be increased or

decreased by 5 to 35 degrees.

5. The time of day will automatically reappear in the display

You do not need to readjust the oven temperature if there

is a power failure or interruption. Broiling, Keep Warm and

Cleaning temperatures cannot be adjusted.

Notes:

Sabbath Mode can be turned on at any time with or

without the oven on.

Sabbath Mode cannot be turned on if the touchpads are

locked out or when the door is locked.

If the oven is baking when Sabbath Mode is set, BAKE

will go out at the end of the baking cycle. There will be

no audible beeps.

If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

When the Sabbath Mode is started, no preheat beep will

sound.

All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

The automatic door lock does not operate during the

Sabbath Mode.

Pressing CANCEL will cancel a Bake cycle, however the

control will stay in the Sabbath Mode.

If power fails, the oven will power up in Sabbath Mode with

72 hours remaining and no cycle active.

La page est en cours de chargement...

Maytag CES3760AAQ Manuel utilisateur

Marque: Maytag

Modèle: CES3760AAQ

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag CES3760AAQ User manual
español: Maytag CES3760AAQ Manual de usuario

Maytag CES3760AAQ Manuel utilisateur

Ce manuel convient également à

Maytag CES3760AAQ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents