Ohaus STARTER 400D Manuel utilisateur

Presented By

Dallas HoustonAustinFt Worth

NicolScales.com

800.225.8181

Contact Us

Nicol Scales & Measurement is an ISO Accredited Calibration

Company that has provided calibration, repair and sales of all types

of weighing and measurement products since 1931.

STARTER 400D

Portable DO Meter

Instruction Manual

Medidor de DO Portátil

STARTER 400D

Manual de instrucciones

STARTER 400D

Oxymètre portable

Manuel d'instructions

EN-2 STARTER 400D Portable DO Meter

TABLE OF CONTENTS

1 INTRODUCTION ................................................................... 1

1.1 Definition of Signal Warnings and Symbols ...................................... 1

1.2 Safety Precautions ............................................................................ 2

1.3 Display and controls .......................................................................... 3

2 INSTALLATION ..................................................................... 5

2.1 Package contents .............................................................................. 5

2.2 Installing the batteries ....................................................................... 5

2.3 Installing the electrode clip ................................................................ 6

2.4 Installing the IP54 cover caps ........................................................... 6

2.5 Integrated stand for table top use ..................................................... 6

3 SETUP ................................................................................... 8

3.1 Setting Auto/Manual Endpoint ........................................................... 7

3.2 Setting Salinity Value ........................................................................ 7

3.3 Setting Temperature Unit .................................................................. 8

3.4 Setting the Date and Time ................................................................ 8

3.5 Setting Power State .......................................................................... 8

3.6 Setting Factory Reset ........................................................................ 8

3.7 Setting New Probe Cap Parameter ................................................... 9

4 OPERATION ........................................................................ 10

4.1 Calibration ....................................................................................... 10

4.1.1 Zero-oxygen solution ................................................................ 10

4.1.2 Performing 1-point calibration .................................................. 10

4.1.3 Performing 2-point calibration ................................................... 11

4.2 Sample measurement ...................................................................... 11

4.3 Temperature measurement .............................................................. 11

4.4 Barometer pressure measurement .................................................. 11

4.5 Using the memory ........................................................................... 12

4.5.1 Storing a reading ...................................................................... 12

4.5.2 Recalling from memory ............................................................ 12

4.5.3 Clearing the memory ................................................................ 12

5 MAINTENANCE .................................................................. 13

5.1 Error message ................................................................................. 13

5.2 Meter maintenance.......................................................................... 13

5.3 Probe maintenance ......................................................................... 14

6 TECHNICAL DATA ............................................................. 15

6.1 Specifications ................................................................................ 15

STARTER 400D Portable DO Meter EN-1

1 INTRODUCTION

Thank you for choosing OHAUS. Please read the manual completely before using the

STARTER 400D portable Optical DO (Dissolved Oxygen) meter to avoid incorrect operation.

The STARTER 400D has an excellent performance/price ratio and is designed with many useful

features. Optical DO probe Other accessories are also available from OHAUS.

Starter 400D offers many practical features such as:

 Ergonomic, multifunctional design for ambidextrous measurements or bench top use

 Meter can measure barometric pressure automatically to compensate the DO value; Salinity

value can be set to compensate the DO value.

 IP54 protection against dust and water

 Ohaus’ renowned user friendly software

1.1 Definition of Signal Warnings and Symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and

warnings. Ignoring the safety notes may lead to personal injury, damage to the instrument,

malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in

injuries or death if not avoided.

CAUTION For a hazardous situation with low risk, resulting in damage to the

device or the property or in loss of data, or injuries if not avoided.

Attention For important information about the product

Note For useful information about the product

Warning Symbols

General Hazard

Explosion Hazard Corrosive Hazard

EN-2 STARTER 400D Portable DO Meter

1.2 Safety Precautions

CAUTION Read all safety warnings before installing, making connections, or

servicing this equipment. Failure to comply with these warnings could result in

personal injury and/or property damage. Retain all instructions for future reference.

 Use the equipment only in dry locations.

 Dry off any liquid spills immediately. The instrument is not watertight.

 Use only approved accessories and peripherals.

 Operate the equipment only under ambient conditions specified in these instructions.

 Disconnect the equipment from the power supply when cleaning.

 Do not operate the equipment in hazardous or unstable environments.

 Service should only be performed by authorized personnel.

WARNING Do not use this instrument in an environment subject to explosion

hazards. The housing of the instrument is not gas tight (explosion hazard due to

spark formation, corrosion caused by the ingress of gases).

CAUTION When using chemicals and solvents, comply with the instructions of the

producer and the general lab safety rules.

STARTER 400D Portable DO Meter EN-3

1.3 Display and controls

Display

31

Time: HH:MM:SS

2

Date: YYYY-MM-DD

3

calibration data: |K-1|≤0.3 and |B|<0.1

Probe condition is very good

calibration data: 0.3≤|K-1|≤0.4 and |B| <0.1

Probe condition is acceptable.

4

Measurement icon - measurement (calibration) is running

5

Calibration icon - calibration is running

6

Power state icon, include power always on icon , means meter will not automatically turn

off; and auto-off icon which means after 10 minutes no operation meter will turn off(see

4.4); power state icon position is at the top-left of the battery status icon.

7

Battery status icon – the charged status of the battery

8

DO reading: mg/L and %

9

Temperature during measurement or in calibration process

10

Barometric pressure during measurement or in calibration process

11

Data log: memory number

12

ppt for salinity entry

11

12

13

1

6

5

4

3

2

7

8

9

10

EN-4 STARTER 400D Portable DO Meter

Controls

Button

Press & release

Press & hold

for 2 seconds

- Start or endpoint measurement

(manual endpoint mode)

- Confirm setting, confirm entered

value for setting

- switch between auto endpoint

and manual endpoint mode

- Start calibration

- Review the latest calibration

data

- Meter turn on

- Back to measurement screen

- Meter turn off

- Store current reading to memory

- Increase value during setting

- Scroll up through the memory

- Recall stored data

- Enter setup screen

- Scroll down through the memory

- Reset factory setting

STARTER 400D Portable DO Meter EN-5

2 INSTALLATION

Carefully unpack the box.

2.1 Package contents

The ST400D kit has the following items:

We also offer ST400D-G kit which includes ST400D kit and a portable bag.

Accessories:

Model

Description

P/N

STDO21

Optical DO probe

30219117

DO Zero Oxygen Chemical

30059257

Portable Bag for portable meters

30031635

2.2 Installing the batteries

 Remove the battery cover screw using a coin or screwdriver and remove the battery cover

 Insert the batteries in the battery compartment as shown

 Replace the battery cover and tighten the battery cover screw

ST400D

Units

STARTER 400D meter

1

STDO21 (with 1.0m cable)

1

AAA battery

4

Electrode Clip

1

IP54 cover caps

1 set

Wrist Strap

1

EN-6 STARTER 400D Portable DO Meter

2.3 Installing the electrode clip

The electrode clip is an electrode holder that can be placed next to the display on either side of

the housing.

 Attach the clip by inserting the tabs into the recess.

 Slide the clip forward to lock in position. Slide the shaft of the probe into the clip from above.

2.4 Installing the IP54 cover caps

Use the small plastic tool as shown:

2.5 Integrated stand for table top use

Starter 400D has an integrated table stand as shown, which can be pushed out to use the meter on

a lab bench or desk. To close the stand, push the middle edge of the stand toward the meter.

STARTER 400D Portable DO Meter EN-7

3 SETUP

Press to enter the setup interface. We have 7 setting items, they are:

1) Auto/Manual Endpoint

2) Salinity Value

3) Temperature Unit

4) Date and Time

5) Power State

6) Reset Factory Setting

7) New Probe Cap Parameter

3.1 Setting Auto/Manual Endpoint

When in calibration, ST400D is only work at Auto End Point Mode.

The default endpoint mode of ST400D for measurement is Auto End Point Mode. When users

want to judge the endpoint manually, you can shift to Manual Endpoint Mode.

End point Mode:

o When in Manual Mode, to manually reach and lock a pH measurement value, you

need to press button- when reading is stable，then the measurement value

freezes; And meter displays .

o When in Auto End Point Mode, the meter determines when the reading is stable

then locks the measurement or calibration value automatically, the reading freezes;

the meter displays .

Users can also change the endpoint mode by shortcut -- Press and hold button- to shift the

End Point Mode.

3.2 Setting Salinity Value

Since salinity has an influence on the dissolved oxygen value, it is important to input the correct

salinity value. The meter can compensate salinity for measurements in solutions with salinity from

0 to 50 ppt. The default value for salinity is 0.0 ppt.

 Press button- or button- to adjust the salinity value.

 Press button- to confirm the value or press button- to return to the Setting screen.

Normally seawater salinity is 35ppt, which means 35g of salt per 1000g seawater.

EN-8 STARTER 400D Portable DO Meter

3.3 Setting Temperature Unit

Ohaus optical DO probe STDO21 include a built-in temperature probe, the meter will be in

Automatic Temperature Compensation (ATC) mode automatically. You can select the temperature

unit according to your preferred: °C or °F .

Note: °C = 5/9 (°F -32)

The default setting is 25 °C (77°F).

3.4 Setting the Date and Time

The Date format is yy-mm-dd. Press button- or button- to adjust the value of each

numerical digit. Press button- to confirm current value then goes to next numerical digit.

3.5 Setting Power State

We have 2 power states: "Auto OFF" or "Always ON".

When "Auto OFF" is selected, which means the meter will turn off the powder without any press

operation after 10 minutes and auto-off icon will display at the top-left of the battery status icon.

"Always ON" means power will not turn off automatically, and the power always-on icon

displays.

Ohaus suggest you to select "Auto OFF” so to save power of batteries.

3.6 Setting Factory Reset

Press button- and button- together to enter the Reset Factory Setting screen.

STARTER 400D Portable DO Meter EN-9

3.7 Setting New Probe Cap Parameter

When replace a new probe cap, user must input the parameter of this new cap into the meter. Or

the measurement value will be incorrect.

Press button- , button- and button- together to enter the new probe cap parameter

setting screen. Input the parameter of the new cap. Then do calibration before any measurement.

Probe Body

Probe

Cap

Protection

Cover

O-ring

EN-10 STARTER 400D Portable DO Meter

4 OPERATION

WARNING Do not operate the equipment in hazardous environments. The

equipment is not explosion protected.

WARNING When using chemicals and solvents, comply with the instructions of the

chemical producer and the general lab safety rules.

4.1 Calibration

STARTER 400D allows you to perform 1-point or 2-point calibrations; Ohaus suggest 1-point

calibration(100% DO calibration) for samples which DO value is not less than 2 mg/L.

Only when measure samples which DO value is lower than 2 mg/L, Ohaus suggest 2-point

calibration.

4.1.1 Zero-oxygen solution

Preparing a zero-oxygen solution: put approximately 20ml of pure or deionized water into the

bottle of DO Zero Oxygen Chemical (30059257, there are about 5g powder in it), stir for at least 5

minutes.

This zero-oxygen solution is used for 2-point calibration.

4.1.2 Performing 1-point calibration

When performing calibration, the meter only uses Auto End Point Mode.

1 point calibration can be performed in the air or oxygen-saturated water. There will be a little

difference between calibration in the air and in oxygen-saturated water.

Before calibration you need to rinse the DO probe with pure water and carefully wipe the water off

with a tissue.

o Place the probe in the air (or in oxygen-saturated water).

o Press button- , the calibration icon appear on the display.

o The meter reaches endpoints automatically, 100% will display. Measurement icon

disappears.

STARTER 400D Portable DO Meter EN-11

Once you have completed your 1-point calibration, you have 3 options new:

o Press button- to finish 1-point calibration then return to measurement screen.

o Press button- to reject calibration and return to measurement screen.

o Press button- to complete a 2-point calibration (after preparing the zero

oxygen solution and putting STDO21 into it).

4.1.3 Performing 2-point calibration

 Perform the 1-point calibration.

 Place the probe in the zero oxygen solution and press button- .

The meter reaches the endpoint automatically. 0% will display then return to measurement

screen.

Pressing and holding button- will display the calibration data.

4.2 Sample measurement

Dissolved oxygen readings can display unit of mg/L or %.

Place the DO probe in the sample. Press to start the measurement.

When the meter reaches endpoint, the measurement reading will freeze on the screen.

4.3 Temperature measurement

For better accuracy, we recommend the use of the temperature probe. If a temperature probe is

used, ATC and the sample temperature are displayed.

STDO21 has a built-in temperature probe.

4.4 Barometer pressure measurement

Barometric pressure influences the DO value.

STARTER 400D has a built-in barometric pressure sensor which can measure the barometric

pressure automatically. This meter uses barometric pressure unit KPa (kilopascal).

EN-12 STARTER 400D Portable DO Meter

4.5 Using the memory

4.5.1 Storing a reading

The STARTER 400D can store up to 99 measurement readings. Press button- when the

measurement reaches end point. indicates that is the 2

nd

measurement reading had

been stored. The starter 400D can store up to 99 measurement readings.

4.5.2 Recalling from memory

Press and hold button- to recall the stored values from memory.

Press button- or button- to scroll through the stored results. Press button- to go

back to the measurement screen.

4.5.3 Clearing the memory

Continue pressing button- to scroll through the stored results until "Clear All" appears.

Press button- to confirm the deletion or press button- to return to the measurement

mode without deleting all the data in the memory.

STARTER 400D Portable DO Meter EN-13

5 MAINTENANCE

5.1 Error message

Low battery

If low battery, the battery icon will blink to show need

new battery. Then turn off after 10 seconds.

Communication fail

When do calibration or new cap parameter input, meter

will detect if the probe is connected properly. If not,

meter displays " Fail, please confirm the STDO21 probe

is connected”

Measured temperature out

of range (< -5°C or >55 °C)

Meter will displays "Temperature Out of Range!"

Please keep the sample temperature within the range for

measurement.

Calibration out of range

Meter displays "Calibration Fail".

|K-1| >0.4 or a |B| >0.1

You may need to do a proper calibration again, if

calibration data is still not good, you may need to replace

a new probe cap or probe.

Recall memory fail

Meter displays "No Data"

When recall memory while no data memorized yet.

The current data set has

already been stored once

Meter displays" Already saved!"

A measurement can only be stored once. Perform a new

measurement to store a new data set.

Any more problems, you can contact Ohaus.

5.2 Meter maintenance

The STARTER 400D does not require any maintenance other than replacement of depleted

batteries. To clean, use a damp cloth.

Attention: Do not disassemble the instrument. There are no user serviceable parts inside.

The housing is made of acrylonitrile butadiene styrene (ABS). This material is susceptible to

damage by some organic solvents, such as toluene, xylene and methyl ethyl ketone (MEK). Any

spillage should be immediately wiped off.

EN-14 STARTER 400D Portable DO Meter

5.3 Probe maintenance

The DO probe measures the oxygen based on luminescence principle. The optical DO probe

measures dissolved oxygen by emitting a blue light of the proper wavelength that causes the

sensing element to luminesce. Oxygen dissolved in the sample continually passes through the

diffusion layer to the sensing layer, affecting the luminescence lifetime. STDO21 can measure the

lifetime of the luminescence as it is affected by the presence of oxygen and compared with the

reference. This technology has been approved by EPA.

When measurement, optical probe did not consume the DO in the sample, that means the sample

do not need stir

Optical probe STDO21 do not need to replace the membrane or any maintenance of anode or

cathode. The optical probe only requires that its sensor cap be replaced every 12-18 months.

Please input the new cap parameter when new probe cap in installed, then do calibration before

any measurement.

When storing the probe for a longer period, make sure it is placed in the wetting protection cover.

Calibration frequency: Ohaus suggest verifying the calibration regularly according to your

measurement requirement. STDO21 only has very little calibration drift when compared to

electrochemical probes. This advantage results in less frequent calibrations. In fact, optical probes

are so stable they are capable of holding their calibration for many months.

Please also read the STDO21 probe manuals before using it.

STARTER 400D Portable DO Meter EN-15

6 TECHNICAL DATA

6.1 Specifications

Ambient conditions

 Altitude: Up to 2000 m

 Specified Temperature range: 5°C to 40°C

 Humidity: maximum relative humidity 80 % for temperatures up to 31°C decreasing linearly to

50% relative humidity at 40°C

 Installation category: N/A

 Pollution degree: N/A

 Operability is assured at ambient temperatures between 5°C to 40°C

Model: ST400D

Measurement Range

%

0.0 to 200.0%

mg/L

0.00 to 20.00mg/L (ppm)

Temp.

0 to 50 °C

Measurement Resolution

%

0.1%

mg/L

0.01 mg/L

Temp.

0.1 °C

Accuracy

± 0.2 mg/L (<8 mg/L)

± 0.3 mg/L (8 to 20 mg/L);

± 0.3 °C

Barometric

Range

50.0 to 115.0 kPa

Resolution

0.1 kPa

Accuracy

1.5 kPa

Temp compensation

ATC

Salinity compensation

0.0 to 40.0 ppt

Calibration

1 point or 2 points

Memory

99 sets, last calibration data

Power

4 x AAA(LR03) batteries, 12 hrs

Size/Weight

90 W x 150 D x 35 H mm

Weight

0.16kg

Display

liquid crystal

IP rating

IP54

T input

Mini-Din

Materials

ABS

La page charge ...

Ohaus STARTER 400D Manuel utilisateur

Ohaus STARTER 400D Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents