LG 1334946 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
Model Name*=color number
P/No. MFL67527912-8
ENGLIS
H
ESPAÑOL
www.lg.com
OWNER’S MANUAL
TOP FREEZER
REFRIGERATOR
Please read this manual carefully before operating
your appliance and retain it for future reference.
LTCS20220*
LTCS24223*
LTCS20120*
GT66BP*
GT58BP*
GT57BP*K
LTWS24223*
LTNS20220*
Copyright © 2018-2019 LG Electronics Inc .All Rights Reserved.
T Copyright © 2018-2019 LG Electronics Inc. odos los Derechos Reservados.
FRANÇAIS
AFN75754512
Copyright © 2018-2019 LG Electronics Inc. Tous droits réservés.
LTCS20020*
LT57BPSX
1
Important Safety Instructions 2-3
Requirements for Ground Connection 3
Parts and Features 4
Water Filter 17
Refrigerator Installation 5-11
gnikcapnU 5
noitallatsnI 5
How to remove and Install the
srooD rotaregirfeR 6-7
How to reverse and Install the
srooD rotaregirfeR 8-11
Closing and Aligning the Doors 11
Using your Refrigerator 12-16
Ensuring Proper Air Circulation 12
Adjusting the Controls
12
Adjusting Control Settings
13
Food Storage Guide
13
Refrigerator Shelves
14
14
Pantry Drawer
Ice Tray
15
Humidity Controlled Crispers 15
sniB rooD 15
Water Dispenser
16
rekamecI citamotuA 16
Dairy Bin 15
Refrigerator Care and Cleaning 18-19
Refrigerator Cleaning 18
Outside 18
81 edisnI
Door Lining & Gaskets 18
Plastic Parts (Covers and Panel)
Back Cover 18
Replacing Refrigerator Lights
18 snoitpurretnI rewoP
When Going on Vacation 18
When Moving
About the Automatic Ice Maker 1 9
Connecting the Water Line 20-22
Troubleshooting Guide 22-26
Warranty
28-32
TABLE OF CONTENTS
TABLE OF CONTENTS
Spanish Version
French Version
Smart Diagnosis
TM
Door Alarm
19
18
18
27
27
66
34
2
This manual contains several important safety notices. Always read and obey all of the following safety messages.
You may be killed or suffer fatal damage if you do not follow instructions.
You may be killed or seriously injured if you do not follow instructions.
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or damage to the product.
All safety messages inform you of potential danger, advise you on how to reduce the risk of injury and tell you what can
occur if the instructions are not followed.
This is the safety alert symbol. This symbol is a warning to potential dangers that could cause death, injury or
damage to you, others or the product. All safety messages will follow after this warning symbol and the word
“DANGER”, “CAUTION” or “WARNING”. These words mean:
IMPORTANT SAFETY INSTRUCTIONS
SAFETY MESSAGES
WARNING
DANGER
WARNING
CAUTION
KEEP THESE INSTRUCTIONS
In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the
room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 10.8 square
feet (1 square meter) in size for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your
particular appliance is shown on the identification plate inside the appliance. Never start up an appliance showing any
signs of damage. If in doubt, consult your dealer.
This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible. When
transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating
circuit are damaged. Refrigerant squirting out of the pipes could ignite orcause an eye injury. If a leak is
detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance
is standing for several minutes.
RISK OF FIRE AND FLAMMABLE MATERIALS
To reduce the risk of fire, electrical shock or personal injury, the following precaution measures should be followed:
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended
by the manufacturer.
Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type
recommended by the manufacturer.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Do not light a candle to remove odors in the refrigerator.
• In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an authorized service
center before resuming use. Do not touch the refrigerator or power cord of the refrigerator.
NEVER disconnect the refrigerator by pulling the power cord, always grip the plug rmly and disconnect it directly from the outlet.
Immediately repair or replace all faulty or damaged service cables. Do not use cords that have cracks or abrasion
damage on the length of the cord or on the plug.
When moving your refrigerator, take care not to roll over the electrical cord.
DO NOT
store or use gasoline or other combustible liquids or vapors in proximity with this or any other electrical appliance.
DO NOT permit children to climb, stand or swing from the doors or shelves of the refrigerator. This can cause serious
injury to them and damage to the product.
Keep your fingers away from areas in which they can become caught, such as the doors, hinges and cabinets. Be
careful closing the doors when children are near.
Unplug the refrigerator before cleaning or repairing. NOTE: We strongly recommend that any repair services be
performed by a qualified professional.
• Before replacing a burned-out light bulb, unplug the refrigerator or shut down the circuit breaker to avoid contact with
a live wire (the bulb could break while being replaced). NOTE: Setting the control to the OFF position does not discon-
nect the power from the light bulb circuit.
If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper disposal by a quali-
fied servicer.
If you release the refrigerant or throw away the insulation foam, you may be fined or imprisoned in accordance with the
relevant environmental law. Insulation foam contains flammable blowing gas.
Do not keep bottles in the freezer compartment, they could explode after freezing and cause damage.
For your safety, this product should be properly grounded. Have a qualified professional check the electrical circuit
and outlet to ensure a proper ground connection.
Read all instructions before utilizing the product. Utilize this product only as explicitly expressed in this guide.
Once the refrigerator is operating, avoid touching cold surfaces of the freezer with damp or wet hands; the skin could
become adhered to these surfaces.
In refrigerators with an automatic ice dispenser, avoid contact with moving parts of the ejector mechanism or with the
heating mechanism that discharges the cubes. DO NOT place your fingers or hands in the ice dispenser mechanism
while the refrigerator is connected.
DO NOT refreeze foods which have already thawed. The Department of Agriculture of the United States, in your Bulle-
tin of Home and Gardens No. 69 establishes that:
“...You can refreeze food that has thawed if they contain ice crystals or are cold and below 40 °F (4 °C)”.
“...Ground beef, perishable food or seafood that is discolored or has an unpleasant odor should not be frozen or
consumed. Consumption of melted ice cream should also be avoided. If the odor or color of food is questionable,
discard it. The food may be dangerous to consume”.
“Partial thawing or refreezing reduces the quality of the food, especially fruit, vegetables and prepared meals. The quality
of red meat is less affected than that of other foods. Use refrozen products as soon as possible in order to
maintain their quality”.
• Do not store any living animal inside your refrigerator.
3
This appliance is not intended for use by children, persons with physical or mental disabilities, persons with reduced
sensory or mental capacity, or persons that lack experience or know-how, unless they have supervision or instruction
in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to
assure that they do not play with the appliance.
Children becoming trapped or suffocated is not
a problem of the past. Discarded and abandoned
refrigerators are a hazard, even if they remain there
“for just a few days”. If you would like to dispose of
your old refrigerator, please follow the instructions
below to prevent any accidents.
BEFORE DISPOSING YOUR REFRIGERATOR
OR FREEZER WHEN NO LONGER IN USE:
Remove the doors and magnetic gaskets.
Leave the shelves in place so that children
cannot easily become stuck in them.
IMPORTANT: Attentively read the following.
TO CONNECT ELECTRICITY
WARNING
ELECTRICAL SHOCK HAZARD
FOR YOUR PERSONAL SAFETY, this appliance must
be properly grounded. Have a qualified electrician
check your wall outlet to ensure that the plug is
grounded properly.
3 prong
grounding type
wall receptacle
3 prong
grounding Ensure proper
plug ground exists
before use
RECOMMENDED GROUNDING METHOD
Your refrigerator must always be plugged to its own
outlet which is adequately grounded. The energy current
should only be 115 V ~ 60 Hz, AC or 127 V ~ 60 Hz, AC
(according to the National rating). and fused at 15 or 20
A. This provides the best performance and prevents an
overload which could cause a fire from the overheating
of the cables. It is recommended that a separate circuit
be used for this appliance, as well as a receptacle that
cannot be disconnected with a switch.
Do not use an extension cable.
It is your responsibilit
y and obligation to replace tw
o-
prong outlets with that of an adequately grounded three-
prong outlet.
Do not, under any circumstance, cut or extract the third
prong from the plug.
NOTE: Before installation, cleaning or replacing light
bulbs, you must disconnect the appliance from the
power source. When finished, plug the appliance back in
and adjust the thermostat to the desired position.
USE OF EXTENSION CABLES
We do not recommend the use of extension cables.
However, if you still choose to utilize an extension cable,
it is absolutely necessary that it is listed in the UL (in
the United States) or CSA (in Canada), that it supports
three-pronged plugs and that the electrical current
support a minimum of 15 A and 120 V.
The use of an extension cable will increase the amount
of space needed behind the refrigerator.
WARNING
REPLACING ELECTRICAL CABLE
If the power cord is damaged, it must be replaced by
our service center or qualified LG technician to avoid
any risk.
CAUTION
DANGER:
CHILDREN MAY BECOME TRAPPED
CFC DISPOSAL
REQUIREMENTS FOR GROUND CONNECTION
Your old refrigerator may have a cooling system that
uses CFC’s (chlorofluorocarbons). CFC affects the
stratospheric layer of the ozone.
f you decide to throw out
your old refrigerator, ensure that CFC contaminants are
properly disposed of by a qualified professional. If you
intentionally remove the CFC refrigerant, you could be
subject to fines or prison in accordance with environmental
legislation in effect.
If you no longer require the use of this unit, contact the
local authorities to dispose of this product in a safe way
because it uses Cycle-Pentane or Pentane as foaming
and flammable gases for insulation. Gases insulation
material require special removal process. This product
contains flammable insulation and refrigerant gases.
WARNING:
Do not extend or modify the power cord length, damage
the power cord may cause electric shock or damage the
unit.
It is recommended use a separate circuit for this product
as well as receptacle which can not be disconnected with
a switch. Do not use extension cords or adapters
ungrounded.
4
PARTS AND FEATURES
Use this page to become more familiar with the parts and features of your refrigerator. Page references are
included for your convenience.
NOTE: This guide covers several models. The refrigerator you have purchased may have some or all of the items
listed below. The locations of the features shown below may not match your model.
Custom Cube Icemaker *
Ice Bin *
Ice Tray *
Freezer Shelf
Freezer Temperature Control
Refrigerator Temperature Control
Shelves
Refrigerator Light (LED)*
Pantry Drawer*
A
B
C
H
F
G
E
D
I
J
K
L
M
N
A
B
C
D
E
F
G
H
N
P
I
J
O
M
K
O
P
Q
L
Crispers
F-Deco Duct
Smart Diagnosis *
TM
Door Alarm *
Freezer Light (LED)*
Freezer Door Bins
Dairy Bin
Refrigerator Door Bins
Refrigerator Door Bins*
* On some models
Q
5
REFRIGERATOR INSTALLATION
WARNING
EXCESSIVE WEIGHT HAZARD
Use the assistance of two or more persons to move or
install the refrigerator. Not following these instructions
may cause injury to the back and other parts of the
body.
UNPACKING
Before installing your refrigerator, remove any tape
or temporary stickers. Do not remove any stickers
that feature warnings, the model serial number or the
technical label of the product located on the back of the
refrigerator.
To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent. Clean with warm
water and let dry.
Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the
adhesive tape or glue. These products can
damage the
surface of your refrigerator. For more information, see
the section on “Impo
NOTE: Remove protective film on doors before plugging
in the unit (on some models).
rtant Safety Instructions”.
The shelves come already installed in their factory
position. Remove the shelves and replace them
according to your spacing needs.
Moving Your Refrigerator:
Your refrigerator is extremely heavy. Make sure you
protect the floor when moving your refrigerator for
cleaning or servicing. Always pull your refrigerator
straight out when moving it. Do not shift from side
to side or “walk” the refrigerator when attempting to
move it as this can cause damage to the floor.
WARNING
EXPLOSION HAZARD
Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator. Not following
these instructions may cause death, explosion or fire
INSTALLATION
1.
2.
3.
CAUTION: Avoid placing the unit near heat
sources, direct sunlight or humidity.
ONCE INSTALLED
1. Carefully clean your refrigerator and remove and dust
accumulated during shipping.
2. Install accessories such as the ice bin, door racks,
shelves, etc., in their proper places. These are already
packed to prevent any possible damage during
shipping.
3. Leave your refrigerator on for 2 to 3 hours before
storing food inside. Verify that there is a flow of cold air
in the freezer compartment to ensure proper cooling.
Your refriger
ator is now re
ady for use.
WARNING:
ţTake care when working with the hinges, base cover
and stops, etc. You may injure yourself.
ţDO not place your hands or any tools in the air vents,
the base cover or in the bottom of the refrigerator. This
may cause injury or electrical shock.
Keep a Proper Distance from Adjacent Objects
Please keep the refrigerator at an adequate distance
from other objects. Insufficient spacing can reduce the
refrigerator’s freezing efficiency and increase electricity
consumption.
2” (5.08 cm)
2” (5.08 cm)
2” (5.08 cm) 2” (5.08 cm)
REFRIGERATOR INSTALLATION
CAUTION:
This appliance is intended to be used in household and
similar applications such as: staff kitchen areas in shops,
offices and other working environments; farm houses
and by clients in hotels, motels and other residential type
environments, bed and breakfast type environments,
catering and similar non-retail applications.
Avoid placing the unit near heat sources, direct
sunlight, or humidity.
To avoid vibration, the unit should be leveled and
placed on even floor. If needed, adjust the leveling
screws to compensate for an unleveled floor. The front
should be slightly taller than the rear to ensure that the
doors close properly. The leveling screws can easily be
turned by slightly tilting the front of the refrigerator,
turning the leveling screws clockwise ( ) to raise it
and counter-clockwise ( ) t
o lower it.
Install the refrigerator in an area between 55 °F (13 °C)
and 110 °F (43 °C). If the surrounding temperature is
lower or higher than previously mentioned, it can
adversely affect the unit.
6
HOW TO REMOVE AND INSTALL THE REFRIGERATOR DOORS
If entrance is lees than 35 inches wide, the refrigerator’s door will need to be removed.
IMPORTANT: Before starting, turn off and unplug the refrigerator. Remove all food and the racks from the doors.
TOOLS YOU MIGHT NEED OR USE
3/8 in
10 mm
Hex Socket Wrench Phillips Screwdriver No. 2 Flat Head Screwdriver Adjustable Wrench
WARNING
ELECTRICAL SHOCK HAZARD
Before you begin, either unplug the refrigerator or
turn off the power at the circuit breaker or fuse box.
Remove food and any door rack from the refrigerator.
Failure to do so could result in death or serious injury.
1. Removing Freezer Door
Gently pry off the Top Hinge Cover with a flat head
screwdriver and remove it. See Fig. 1.
Using 10 mm or 3/8 inch socket wrench, remove
the three bolts and lift the Top Hinge (See Fig. 2). Set
parts aside.
Lift freezer door slightly and remove it (See Fig. 3) Set
parts aside.
2. Removing Refrigerator Door
Loose and remove the two bolts and the screw to
remove the middle hinge bracket from refrigerator
housing (Figure 4). Set parts aside (Figure 5).
Lift up door slightly and remove it (See Figure 6).
REFRIGERATOR INSTALLATION
Hinge Pin
Middle Hinge Bracket
Fig. 1
Fig. 3
Middle
Hinge Bracket
Fig. 4
Fig. 5
1/4 in
(For additional support on this topic, including helpful videos, please visit us at: www.lg.com
).
Fig. 2
Middle
Hinge Bracket
7
To replace doors, begin with refrigerator door and then
follow with freezer door.
3. Replacing Refrigerator Door
Set door on Bottom Hinge Pin (See Figure 7).
Place hinge pin of middle bracket inside the hinge pin
insert on the top of the door (See Figure 8). Hold the
door in place and line up the hinge with the holes in
the refrigerator housing.
Use the two bolts and the screw to refasten the middle
hinge with the refrigerator housing. See Figure 9.
4. Replacing Freezer Door
Set the freezer door onto the Middle Hinge pin (Figure
10).
Place upper hinge in the top of the freezer door and
line up the hinge with the holes in top of refrigerator.
Use the three bolts to fasten the hinge (See Figure 11).
Carefully, force the top hinge cover back into place over
hinge (See Figure 12).
REFRIGERATOR INSTALLATION
Fig. 8
Fig. 9
Fig. 12
Bottom Hinge Pin
Fig. 6
Fig. 10
Fig. 7
REFRIGERATOR INSTALLATION
Fig. 11
8
HOW TO REVERSE AND INSTALL THE REFRIGERATOR DOORS (on some models)
You may find it more convenient to have the doors converted from the left opening type (factory installed) to the right
opening type. Directions refer to the right side as the side on your right as you face the unit.
1. Removing Freezer Door
Gently pry off the top hinge cover with a flat head
screwdriver and remove.
Using 10mm or 3/8 inch socket wrench, remove the
three bolts and lift off the top hinge. Set parts aside
Slightly lift up the refrigerator door and remove it.
Turn the freezer door upside down on a non-scratch
surface. Loosen the screw to remove the Door
Closer/Stop and Hinge Pin Insert.
Move the Hinge Pin Insert Bracket to the other side of
the door, keeping the same orientation, and move the
Hinge Pin Insert into the hole on the left side of the
bracket.
Reverse the Door Closer/Stop by flipping it over. Place
it
on top of the Hinge Pin Insert Bracket, and tighten bo
th
down with the screw.
Pry off the cover on the top left side of the refrigerator to
uncover the screw holes.
Set the freezer door and top hinge parts to the side and
remove the refrigerator door.
REFRIGERATOR INSTALLATION
Hinge Pin
Middle Hinge Bracket
Hinge Pin
Insert Bracket
Hinge Pin Insert
Cover
(on top of
refrigerator)
REVERSIBLE DOORS MODELS
LTCS20220*
LTCS24223*
GT66BP*
GT58BP*
LTWS24223*
LTNS20220*
LTCS20020*
LT57BPSX
WARNING
ELECTRICAL SHOCK HAZARD
TOOLS YOU MIGHT NEED OR USE
3/8 in
10 mm
Hex Socket Wrench Phillips Screwdriver No. 2 Flat Head Screwdriver
1/4 in
Before you begin, either unplug the refrigerator or turn off the power at the circuit breaker or fuse box. Remove
food and any door rack from the refrigerator. Failure to do so could result in death or serious injury.
9
2. Reversing and Reinst
alling Refrigerator Door
Using a ¼” socket wr
ench, loosen and remove Hinge
Pin fr
om the Middle Hinge Bracket. Remove washer
undernea
th the middle hinge and set aside.
NOTE: At this point the door
will be loose. Slightly lift the
door and remove it.
Loosen and remove the tw
o bolts and use the Phillips
head screwdriver to remov
e the Middle Hinge Bracket
from the refrigerat
or housing. Set parts aside.
Remove the washer fr
om the Bottom Hinge Pin.
Using a ¼” socket wr
ench, loosen and remove the
Hinge Pin from the Bott
om Hinge. Reattach the
Hinge Pin to the opposit
e side of the hinge.
NOTE:
NOTE:
WARNING:
This is easier to do
while the hinge is still
attached.
Using a 3/8’’ socket wrench with a 2-Inch extension
and screwdriver, loosen the two bolts and one screw, and
remove the Bottom Hinge from right side of the housing.
Remove the Decorative Caps on the bottom of the
refrigerator housing. You will need these holes for the
Bottom Hinge.
Move the Bottom Hinge to the left side of the housing,
keeping the same orientation, and reattach with the
two bolts and one screw. The flat screw must be
placed on the exterior side of the hinge. Move the
Decorative Bolt to the hole on the lower right side
of the housing.
Turn the refrigerator door upside down on a
nonsc
to remove the Bottom Hinge Pin Insert Bracket
with the Hingr Pin Insert.
If you reinstall or replace doors, move
ratching surf
The leveler is only present on some models.
ace. Loosen the two screws
REFRIGERATOR INSTALLATIONREFRIGERATOR INSTALLATION
Leveler
the leveler to the opposite side.
Hinge Pin
Insert
Hinge
Pin Bracket
Door
Closer/
Stop
Door
Closer/
Stop
Hinge Pin
Insert
Hinge
Pin Bracket
10
With a flat-head screwdriver, carefully pry off and
remove the cover over the screw holes on the left side of
refrigerator housing.
Remove the outer lower Decorative Screw from the
housing at the area between the freezer and refrigerator
doors. (You will need this hole for the Middle Hinge
Bracket.)
Flip the Middle Hinge Bracket, (flange will now be on
top) position it on left side of the refrigerator and reattach
with two bolts and a Phillips screwdriver. Place the
refrigerator door down over the pin on the bottom hinge.
Place the washer between the refrigerator door and
middle hinge and re-attach Hinge Pin to Hinge Bracket
with a ¼” socket wrench.
NOTE: Bracke
NOTE:The Door Closer Stop is only presented on some
t has been flipped, but Hinge Pin stays
in the same orientation with its hexagonal end facing
upward.
Insert the Decorative Screw into the outer hole on the
right side of the housing. Attach cover on the right side.
Cover is force-fitted.
REATTACHING THE DOORS
Place the freezer door down over the Hinge Pin on the
Middle Hinge Pin Bracket.
Place the Upper Hinge Pin on top of the freezer door
and line up the Upper Hinge with holes on top of the
refrigerator. Use the three bolts to replace the Hinge.
Middle Hinge
Bracket
Flange
Decorative
Screw
REFRIGERATOR INSTALLATION
Reverse the Door Closer/Stop by flipping it over. Place
it on top of the Hinge Pin Insert Bracket, and tighten
both down with the screw. Tighten the Hinge Pin
Bracket to the door.
models.
11
Tighten the bolts. Force-fit Top Hinge Cover over Top
Hinge.
Replace cover on the top left side of the refrigerator
to the right top to cover the holes. Cover is also
force-fitted.
After changing doors, make sure that the corners
of the Door Gaskets are not folded over. To ensure a
good seal, apply a small amount of silicon grease on
the corners of gaskets.
Corners
Cover (on top of
refrigerator)
REFRIGERATOR INSTALLATION
REFRIGERATOR INSTALLATION
CLOSING AND ALIGNING THE DOORS
To avoid vibration, the unit must be leveled. If necessary,
adjust the Leveling Legs to compensate for unevenness
of the floor. The front should be slightly higher than the
rear to aid in door closing.
Your refrigerator has three front leveling screws, one on
the right and one on the left. If your refrigerator seems
unstable or if you would like the doors to close more
easily, simply adjust the inclination of the refrigerator by
following the instructions below:
NOTE: Third leveling screw is used for protection of
hinge lower.
1. Plug the refrigerator into a 3 prong grounded outlet.
Move the refrigerator into its final position.
2.
Use a 11/16” (18 mm) wrench or an adjustable wrench
to adjust the leveling screws (see Figure A), turning
clockwise to raise the side of the refrigerator and
counter-clockwise to lower it. It may take several turns
to adjust it to the inclination you would like.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling legs.
This will make it easier to adjust the level.
3. Open both doors again and check to make sure that
they close easily. If not, tilt the refrigerator slightly
more to the rear by turning both Leveling Screws
clockwise. It may take several more turns, and you
should turn both Leveling Screws the
same times.
Door Alignment
If the space between your doors is uneven, follow the
instructions below to align the doors:
1. Gently pry off the Top Hinge Cover with a flat head
screwdriver and remove.
2. Loosen the Top Hinge Bolts using a 10 mm or 13/32
inch socket wrench or open-end wrench.
3. Have someone hold the freezer door so the space
between the two doors is even, and retighten the top
hinge bolts.
4. Replace the Top Hinge Cover.
Figure A
12
ENSURING PROPER AIR CIRCULATION
In order to obtain stable temperature, the air must flow
between the freezer and refrigerator sections. As shown
in the illustration below, the cold air enters through
the bottom part and circulates upward. This air returns
below the freezer floor and the rest of the air enters the
refrigerator section through the top vent.
Do not block any of these vents with packages of food.
This can interrupt the flow of air and cause temperature
and moisture problems.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer
to the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out
of food, make sure you wrap or cover foods tightly (See
the “Food Storage Guide” section for details).
NOTE:
If you close the fresh food
compartment door applying
more force than necessary,
freezer door may get open and
close again, due internal air flow
of refrigerator.
ADJUSTING THE CONTROLS
ţYour refrigerator has two controls that allow you to
regulate the temperature the freezer and refrigerator
compartments.
ţRefrigerator Control (On Some Models)
Initially set the Refrigerator Control on the middle
setting (number 3). To do so, press the TEMPERATURE
ADJUST button until it reaches the middle position
(the third LED turns ON). Leave the refrigerator on this
setting for 24 hours to reach the correct temperature.
After 24 hours, adjust the compartment temperature
as you desire. ALWAYS wait 24 hours before you adjust
the temperature. If you want to set the refrigerator
compartment temperature to a warmer temperature
than the current, continue pressing the TEMPERATURE
ADJUST button until it reaches the desired temperature.
ţDemo Mode (For Store Use Only)
Demo Mode disables all cooling in
the refrigerator and freezer sections to conserve energy
while on display in a retail store. When activated, OFF
will display on the control panel.
To deactivate:
Press the TEMPERATURE ADJUST button until your
desired temperature setting is reached. The OFF light
will turn off once the Demo Mode is deactivated.
ţFreezer Control
The freezer control should come from factory on the
middle setting (number 3). Wait 24 hours before
adjusting the freezer compartment temperature. Roll
the knob to set the freezer temperature as you desire.
ALWAYS wait 24 hours after any adjustment to reach the
desired temperature.
NOTE: Setting at higher number
of the freezer compartment, the
temperature of freezer compart-
ment becomes colder.
USING YOUR REFRIGERATORUSING YOUR REFRIGERATOR
13
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before adding
food to the refrigerator. The mid-settings indicated in the
previous section should be correct for normal household
refrigerator usage. The controls are set correctly when
milk or juice is cold to your liking and ice cream is firm.
The refrigerator control functions as the thermostat for
the entire appliance. The higher the number setting, the
longer the compressor will run to keep the temperature
colder. The freezer control adjusts the cold air flow from
the freezer to the refrigerator. Setting the freezer control
to a lower temperature keeps more cold air in the freezer
compartment to make it colder.
If you need to adjust the tempe
rature in the refrigerator
or freezer, begin by adjusting the refrigerator first. Wait
24 hours after the refrigerator adjustment to check the
freezer temperature. If it is too warm or too cold, then
adjust the freezer control as well.
Use the settings listed in the table below as a guide.
CONDITION/REASON: RECOMMENDED
ADJUSTMENT:
REFRIGERATOR section
is too warm
Opening the door often
Adding a large amount
of food
Room temperature is
very warm
Adjust the
REFRIGERATOR setting
to the next highest
number and wait 24
hours, then check.
FREEZER section is too
warm/ ice is made too
slowly
Opening the door often
Adding a large amount
of food
Room temperature is
very low (not cycling
often enough)
Using ice frequently
Air vents blocked by
objects
Adjust the FREEZER
setting to the next
highest number and wait
24 hours, then check.
Remove any objects
blocking air flow.
REFRIGERATOR section
is too cold
Controls not set
correctly for your
conditions
Adjust the
REFRIGERATOR setting
to the next lowest
number and wait 24
hours, then check.
FREEZER section is too
cold
Controls not set
correctly for your
conditions
Adjust the FREEZER
setting to the next lowest
number and wait 24
hours, then check.
FOOD STORAGE GUIDE
ITEMS HOW TO STORE
Storing Fresh Food Wrap or store food in the
refrigerator in airtight and
moisture-proof material unless
otherwise noted. This prevents
food odor and taste transfer
throughout the refrigerator. For
dated products, check date code
to ensure freshness.
Butter or
margarine
Store opened butter in a covered
dish or in a closed compartment.
When storing a larger quantity,
wrap in freezer packing and
freeze.
Cheese Store in original packaging until
you are ready to use it. Once
opened, tightly rewrap with
plastic wrap or aluminum foil.
Vegetables with
skins (carrots,
peppers)
Place in bags or plastic containers
inside the crisper.
Fruit Wash and let dry; store in plastic
bags in the refrigerator. Do not
wash or pit berries until you
are ready to eat them. Berries
should be selected and kept in
their original packaging (if there
is any) or in a paper bag closed
halfway and set on a shelf.
Leafy Vegetables Remove original packaging and
trim any dirty or discolored parts.
Wash in cold water and drain.
Place in a plastic bag or plastic
container and store in the crisper.
Fish Consume fish or seafood the
same day purchased.
Chef Fresh Store any meat in original airtight,
moisture-proof packaging.
Rewrap if necessary.
Leftovers Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with airtight lids can
also be used.
USING YOUR REFRIGERATOR
14
Packaging Recommendations:
Us se s containers.
Us s containers o surface.
Package f o resistance.
Wr yered stic.
Use wat roo stic.
Us rec s t store frozen foods.
Follow these or container instructions in order
t
re est freezing
Do not use:
Bread r
Plas c o safe f storing.
Containers seals.
Wax wax stic.
Thin wr ot wat roof.
Freezing
IMPORTANT:
o k ottle freez
c r t ter free
caus
For the a use of your freezer do not store exces
food. not introduce a large of unfrozen f
that cannot frozen within 24 hours (no re
2–3 or ,91 kg - 1,36 kg of food squar
inch of ce in the freezer). Sufficient ce st
left in order for the air to circulate r around
es. Leave enough ce in order to close y
refrigerator ty.
Storage
es can vary on the t
quality of the food, the way its or
container used, (in c son to air and ty),
the t rature it stored in. Ice crystals f
inside your are it indicates the air
t av condensed.
NOTE: Let w
foods cool off at r t ratur
for ro ately 30 then wr accordingly
the ethods ove and freeze. By letting y
w foods cool off fore you introduce to y
freez save y rgy.
WARNING
SUFFOCATING DANGER
Adequate ventilation is required when using dry ic
ry ice is oxide (CO
2). When it e rates
roduces oxygen, causing dizziness, slight headache
unconsciousness or death. not inhale these r
and r ventilate the r while in use fdryic
USING YOUR REFRIGERATORUSING YOUR REFRIGERATOR
REFRIGERATOR SHELVES
The glass shelves in your refrigerator are adjustable to
meet your individual storage needs.
Adjusting the shelves to fit different heights of items will
make finding the exact item you want easier. Doing so
will also reduce the amount of time the refrigerator door
is open which will save energy.
IMPORTANT: Do not clean glass shelves with warm water
while they are cold. Shelves may break if exposed to
sudden temperature changes or impact.
NOTE: Glass shelves are heavy. Use special care when
removing them.
Adjusting Shelves
Remove shelves from the shipping position and replace
shelves in the position you want.
To remove a shelfTilt up the back of the shelf in the
direction of 1 and lift it in the direction of 2 . Pull
the shelf out.
To reinstall a shelf—
Slide the shelf into
the guides until it
stops.
1
2
PANTRY DRAWER (on some models)
To remove the Pantry Drawer:
1
2
15
Grasp the drawer handle and pull it forward to the drawer
stop. Lift up and pull out.
To replace the Pantry Drawer:
Slide the drawer back all the way past the drawer stop.
Ice Tray (On some models)
indicated in the picture. Do not
overfill with water or ice cubes
will be difficult to remove
freezer dial to 3.
Twist the ice tray to remove the
ice cubes
so may result in damage to the
tray.
pour water on the back of the
tray or soak it in water before
removing ice cubes.
USING YOUR REFRIGERATOR
HUMIDITY CONTROLLED CRISPERS
The crispers provide fresher tasting fruit and vegetables
by letting you easily control humidity inside the drawer.
You can control the amount of humidity in the
moisturesealed crispers by adjusting the control to any
setting between VEGETABLES and FRUIT.
VEGETABLES keeps moist air in the crisper for bes
storage of fresh, leafy vegetables.
FRUIT lets moist air out of the crisper for best storage
of fruit.
To remove and install the crisper drawers:
1. Pull the crisper drawer out to the drawer stop.
2. Lift the front of the crisper up, then pull it straight out.
3. To install, slightly tilt up
the front, insert the drawer
into the frame and push it
back into place, past the
drawer stop.
To remove the crisper glass:
1. Remove the
crisper drawers (as
described above).
2. Reach in under
the glass and lift up.
3. Gently push the
glass up and out.
To remove the crisper cover:
1. Remove both
crisper drawers.
2. Remove the
crisper glass.
3. While holding the
support and crisper
cover, pull upand
out.
DOOR BINS
The door bins are removable for easy cleaning and
adjustment.
1. To remove the bin, simply lift the bin up and pull
straight out.
NOTE: Some bins may vary in appearance and will
only fit in one location.
2. To replace the bin,
slide it in above the
desired supportand
push down until it
snaps into place.
DAIRY BIN
1. To remove the Dairy Bin, simply lift up and pull out.
2. To replace the Dairy Bin, slide it in above the desired
support slots and push down until it stops.
Dairy Bin
16
USING YOUR REFRIGERATOR
WATER DISPENSER (On some models)
Dispenser
Switch
WHEN YOU SHOULD SET THE ICEMAKER
POWER SWITCH TO OFF (O)

When the water supply will be shut off for several hours.
WARNING: Do not put your fingers up the ice chute
CAUTION: Do not dispense ice into fine china or
crystal glasses. China or crystal can break.
AUTOMATIC ICEMAKER (on some models)





When the ice bin is removed for more than one or two
minutes.

When the refrigerator will not be used for several days.
NORMAL SOUNDS YOU MAY HEAR

CAUTION:



Icemaker
Power Switch
Ice detecting
sensor

PREPARING FOR VACATION
Some dripping may occur after dispensing. Hold your cup
beneath the dispenser for a few seconds after dispensing to
catch all of the drops.
Set the icemaker power switch to OFF (O) and shut offthe water
supply to the refrigerator.
To dispense cold water, push on the dispenser switch with a
glass.
NOTE: The ice bin should be emptied when the icemaker
ON/OFF switch is turned to the OFF position.
The icemaker will produce approximately 100-130 cubes in
a 24-hour period, depending on freezer compartment
temperature, room temperature, number of door openings
and other operating conditions.
opening. Doing so can result in severe injury.
It takes about 12 to 24 hours for a newly installed refrig-
erator to begin making ice. Wait 72 hours for full ice
production to occur.
Ice making stops whe
n the bin fills to the level of the feeler
arm.
To turn off the automatic icemaker, set the icemaker
switch to OFF (O). To turn on the automatic icemaker,set
the switch to ON (I).
The water pressure must be between 20 and 120 psi on
models without a water filter and between 40 and 120 psi
on models with a water filter to produce the normal
amount and size of ice cubes.
Throw away the first few batches of ice (about 24 cubes).
This is also necessary if the refrigerator has not been used
for a long time.
Never store beverage cans or other items in the ice bin for
the purpose of rapid cooling. Doing so may damage the
icemaker or the containers may burst.
Never use thin crystal glass or crockery to collect ice. Such
containers may chip or break resulting in glass fragments
in the ice.
DO NOT place fingers or hands on the automatic ice
making mechanism while the refrigerator is plugged in.
WARNING
Personal Injury Hazard
NOTE: The ice bin should be emptied anytime the icemaker
ON/OFF switch is turned to the OFF (O) position.
NOTE: Keeping the power switch in the ON (I) position
before the water line is connected can damage the
icemaker.
The icemaker water valve will buzz as the icemaker fills with
water. If the power switch is in the ON (I) position, it will buzz
even if it has not yet been hooked up to water. To stop the
buzzing, move the power switch to OFF (O).
You will hear the sound of cubes dropping into the bin and
water running in the pipes as the icemaker refills.
If the ambient temperature will drop below freezing, have a
qualified technician drain the water supply system to prevent
serious property damage due to flooding caused by ruptured
water lines or connections.
17
WATER FILTER
AFTER INSTALLING THE WATER FILTER:
WATER FILTER (On some models)
It is recommended that you replace the water filter.
2. Turn the filter counterclockwise and then pull down and out.
Make sure to rotate the filter down completely before pulling
it out of the manifold hole.
Dispense 2.5 gallons (9.46 liters) of water to purge the
system, depressing and releasing the dispenser pad in
cycles of 30 seconds ON and 60 seconds OFF. Open the
refrigerator door and check the shelf area for water leaks.
NOTE: Replacing the water filter causes a small amount of
water (around 1 oz. or 25 cc) to drain. Wrap a cloth around
the front end of the water filter cover to collect any water.
Hold the water filter upright, once it is removed, to leaking
prevent any remaining water from spilling out of the water
filter.
NOTE: The substitute cap must be retained for the future.
If the filter is removed and not replaced, it is necessary to
reinstall the substitute cap to prevent water leaks from the
filter housing.
Approximately every 6 months.
When the Filter Exchange indicator turns on.
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
REMOVE THE OLD WATER FILTER.
REPLACE WITH A NEW WATER FILTER
1. Remove the red cap from the filter.
1. Replace the shelf to the initial position.
2. Turn on household water supply.
3.
Replacement Filter: ADQ72910906.
3. Push the water filter up into the filter receptacle and rotate it
clockwise to lock it into place. Once installed correctly, you
should not be able to rotate the filter clockwise any more.
1. Make sure to turn off the household water supply.
2. Insert the filter into the filter receptacle on the left side of
the refrigerator compartment.
18
WARNING
EXPLOSION HAZARD
Do not use flammable cleaners. Not following these
instructions can cause death, explosion or fire.
The refrigerator, as well as the freezer, do their own
de-freezing. This process does not prevent the build
up of contaminants, therefore it is suggested that you
clean both parts once a month; clean spilled liquids
immediately.
REFRIGERATOR CLEANING
ţUnplug your refrigerator.
ţPull out all of the removable parts (such as the
vegetable and dairy doors).
ţUse a clean sponge (or a soft rag) and use it with
lukewarm water mixed with detergent. Do not use
abrasive or concentrated cleaners.
ţHand wash it, and dry it thoroughly.
ţPlug the refrigerator back in.
OUTSIDE
Wax the outside in order to create better protection. Make
sure you use a product specifically design to be used
for electro-domestic products (car wax is acceptable).
Use a clean, soft rag, and perform this task twice a year.
For metal-made refrigerators, do not wax, simply clean
it with water and detergent. Do not use concentrated or
abrasive products.
In case of STS, apply cleaner in same direction that hair
line of STS.
NOTE: Avoid the usage of chemical products that
contain phosphates or bleach.
INSIDE (Allow freezer to slightly warm up a small
degree to prevent cloth from sticking)
In order to eliminate bad odors, clean the inside of
the refrigerator with a mixture of baking powder and
lukewarm water (one teaspoon of baking powder per cup
of water). Ensure that the powder dissolves thoroughly, in
order to prevent any sort of damage.
DOOR LINING AND GASKETS
Use only a mild detergent (such as dish soap).
PLASTIC PARTS (Covers and Panels)
Do not use abrasive, paper or rough products. These
could damage the product.
BACK COVER
WARNING
ELECTRICAL SHOCK HAZARD
Before you begin, either unplug the refrigerator or turn
off power at the circuit breaker or fuse box.
NOTE: Back Cover should only be
removed by a qualified technician.
In order to get an efficient
performance of your refrigerator,
clean the back cover of it at least
twice a year.
REPLACING REFRIGERATOR LIGHTS
The refrigerator and freezer compartment lights
are LED interior lighting, and service should
be performed by a qualified technician.
WARNING
ELECTRIC SHOCK HAZARD
Before replacing a burned-out light bulb, either unplug
the refrigerator or turn off power at the circuit breaker
or fuse box.
BACK
COVER
REFRIGERATOR CARE AND CLEANING
POWER INTERRUPTIONS
1. In case of a black out, call your electric company and
ask how long it will last.
2. In case of a 24 hour or less black out, do not open the
refrigerator; this will keep the food fresh.
3. In case of a longer black out, do one of the following
options:
ţ Pull out all of the frozen food and keep them in an ice
chest.
ţ Put 2 lbs (907 g) of frozen ice (make sure you use
gloves) for each square foot (28 L) inside the freezer.
This task will preserve the food from 2 to 4 days.
ţ In case you do not possess neither ice chest or dry ice,
consume your food as soon as possible.
REMEMBER: In a power failure, a full freezer stays cold
longer than a partially filled one. A freezer full of m
eat
stays cold longer than a freezer full of baked goods. If
you see that food contains ice crystals, it may be safely
refrozen, although the quality and flavor may be affected.
If the condition of the food is poor or if you feel it unsafe,
dispose of it.
WHEN GOING ON VACATION
If you decide to leave your refrigerator on when going
away, consider these steps:
1. Consume all of the perishable items and freeze the
rest.
2. Empty the ice bin.
If you decide to leave your refrigerator off:
1. Remove all of the food.
2. Unplug your refrigerator.
3. Clean and dry it well.
4. Make sure the doors stay open (use blocks or tape) in
or
der to prevent bad odors and fungi from happening.
19
WHEN MOVING
If you decide to take your refrigerator with you when
moving, consider the following:
1. Remove all of the food from it, and place the frozen
food in an ice chest with dry ice.
2. Unplug your refrigerator.
3. Empty the water from its tray.
4. Clean and dry it with a rag.
5. Pull out all of the removable parts, and wrap them with
adhe
sive tape.
6. Depending on the model of the refrigerator, lift the top
part of the refrigerator so it can roll with ease, or screw
the levelers so it won´t scratch the floor. Consult to the
section “Closing and Aligning Doors”.
7. Keep the doors closed with the cable glued to the
refrigerator cabinet with an adhesive tape.
When your refrigerator arrives to your home, put
everything back into place and read the
section
“Refrigerator Installation” in order to obtain installation
preparation. In case your refrigerator has a factory ice
maker, remember you have to reconnect the water
supply
.
REFRIGERATOR CARE AND CLEANINGREFRIGERATOR CARE AND CLEANING
ABOUT THE AUTOMATIC ICE MAKER
NOTE: The automatic Ice maker is only included in some
models. Check your specifications of your refrigerator.
WARNING
PERSONAL INJURY HAZARD
Avoid contact with any moving parts of the ejector
mechanism or with the heater that releases the ice
cubes. DO NOT place your fingers in the automatic ice
maker when the refrigerator is plugged in.
OPERATING INSTRUCTIONS
After turning on your refrigerator, the ice will start to be
made between 12 and 24 hours.
Identify your ice maker type.
Type 1
Icemaker
Power Switch
Ice detecting
sensor
The ice maker produces 8 cubes per cycle (between 64
and 128 cubes in a 24 hour period), depending on the
temperature of the freezer, the times in which the door
opens, and other using conditions (amount of food in
the freezer, etc).
If the refrigerator is used before the connection of water
to the ice maker was performed, you must turn its dial
to O (off).
When the water connections are performed, turn its dial
to I (on).
The ice maker will fill up (and start making ice) between
12 and 24 hours after the refrigerator is turned on.
Throw away the first batch of ice. Make sure that nothing
interferes with the sensor.
When the ice reaches the sensor, the ice maker will stop
to make ice immedia
tely.
It’s normal that some ice gets stuck. If the ice is not used
frequently, the older cubes of ice will be opaque in color,
smaller, and
with a strange flavor.
NOTE: Never store beverage cans or other items in the
ice bin for the purpose of rapid cooling. Doing so may
damage the ice maker or the container may burst.
YOU MUST TURN THE SWITCH TO O (OFF)
When the water supply is interrupted for many hours.
When the ice container is left out of its place for more
than one or two minutes.
When the refrigerator will not be in use for various
days.
NORMAL SOUNDS
The valve will emit a buzzing sound when the ice maker
is full of water. If the switch is placed in the on position
the buzz will still be heard even when the water pipe
has not been connected. To avoid this sound, move
switch to O (off) position.
NOTE: The ice maker can get damaged if the switch is
kept in the ON position before the water pipe has been
connected.
While
the ice maker is filling up with water and
producing ice, you will hear the sound of the ice falling
and water flowing through the pipes.
You will hear the sound of cubes dropping into the
bin and water running in the pipes as the icemaker
refills.
PREPARING FOR VACATIONS
Move the ice maker switch to the O (off) position and cut
the flow of water going into the refrigerator.
If room temperature is at freezing point, have a
specialized technician drain the flow of water from the
inner pipes (certain models) to avoid broken pipe related
damage.
NOTE: To avoid water spilling, the unit should be leveled
and placed on even floor. Do not remove the ice bin
from the ice maker for a long period, doing so may
cause ice spilling.
1 / 1

LG 1334946 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

dans d''autres langues