Hobart Legasy HL600 Manuel utilisateur

Marque: Hobart

Modèle: Legasy HL600

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Ce manuel convient également à

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

INSTRUCTION

MANUAL

MODELS

HL600 & HL662

ML-141104

ML-141105

F45239 (December 2013)

– 2 –

TABLE OF CONTENTS

GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . 4

Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Bowl Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Agitator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power Bowl Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Prepare for Mixing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Timer Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operating Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Unloading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Wire Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Agitators and Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CLEANING. . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 19

– 3 –

INSTALLATION, OPERATION AND CARE OF

LEGACY

60 QUART MIXERS

SAVE THESE INSTRUCTIONS

GENERAL

The Legacy

60 quart mixer series are heavy-duty mixers which feature a 2.7 horsepower motor,

SmartTimer

™

, a power bowl lift and a #12 attachment hub as standard equipment.

The Legacy

series is available in three models:

• The HL600 is equipped with Stir, plus four mixing speeds.

• The HL662 is equipped with two mixing speeds.

A 40 quart bowl and agitators are also available.

A variety of attachments, agitators and accessories are available. These are described in a separate Use

and Applications Handbook, which is furnished on the Legacy

Mixer Operator Training CD provided with

each mixer.

– 4 –

INSTALLATION

UNPACKING

Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found

to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of

delivery.

LOCATION

Prior to installation, test the electrical service to assure that it agrees with the speciﬁ cations on the machine

data plate.

Place the mixer in its operating location. There should be adequate space around the mixer for the user

to operate the controls and to install and remove bowls. The area above and to the right side of the mixer

should allow the top and side covers to be removed for routine maintenance and servicing.

Once in position, the mixer must be leveled:

• Remove the two top cover screws and the top cover.

• Place a level on the top rim of the large pulley (Fig. 1). Slide shims under the base contact surface

of the mixer as required to level it front-to-back and side-to-side.

• Do not replace the top cover until installation is completed.

Check Lubrication Before Use

This mixer is shipped with oil in the transmission. Check oil level before starting mixer. Refer to Lubrication

page 15 for applicable lubrication procedures.

Transmission Fill Plug / Oil Dipstick

Fig. 1

Top Rim

– 5 –

ELECTRICAL CONNECTIONS

Electrical and grounding connections must comply with the applicable portion

of the National Electrical Code and/or other local electrical codes.

DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /

tagout procedures.

A hole for 3/4"-trade-size conduit is located at the top of the pedestal. Make electrical connections per the

wiring diagram located on the inside of the top cover.

Single-Phase Mixer:

• Connect ﬁ eld supply lead wires to L1 and L2.

• Connect ground wire to ground lug on the mixer.

• Cut off stripped portion of L3 on Legacy

Mixer and wrap securely with electrical tape to insulate

the exposed conductor.

Three-Phase Mixer:

• Connect ﬁ eld supply lead wires to L1, L2 and L3.

• Connect ground wire to ground lug on the mixer.

Check Initial Operation

1. Apply power to the mixer.

2. Turn the SPEED dial pointer to STIR for the HL600 and to 1 for the HL662.

3. Install the bowl and lock into mix position, with the Bowl Support all the way up and bowl guard

closed. Momentarily run the machine by pushing the START and then STOP buttons.

– 6 –

OPERATION

Moving agitator in bowl, keep hands, clothing and utensils out while in

operation. Do not use without interlocked guard.

The Legacy

mixer is equipped with SmartTimer

™

controls and a power bowl lift. Other operating parts

(Fig. 2) and their functions are described throughout the Operation section.

The Wire Cage must be in position or the mixer will not operate.

The bowl must stay in locked position on Bowl Support or the mixer will not operate.

If the Bowl Support is not all the way up (mix position), the mixer will not operate unless the START button

is pressed and held.

If the Bowl Support is not at the mix position and the START button is pressed and held, the mixer will

operate only in Stir speed.

Fig. 2

Controls

Attachment Hub

Wire Cage

Drip Cup-

Splash

Guard

Assembly

Agitator

Apron

Bowl Lock Lever

Bowl Support

– 7 –

CONTROLS

Model HL600 (With Four Mix Speeds Plus Stir Speed)

Model HL600 Mixer Speeds

STIR (Slow) STIR speed is for incorporating ingredients at the start of each mixing

process.

Speed 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters and

potatoes.

Speed 2 (Medium-low) This speed is for mixing cake batters, mashing potatoes and developing

bread dough.

Speed 3 (Medium-high) This speed is for incorporating air into light batches, as well as ﬁ nishing

whipped items.

Sped 4 (High) This speed is for maximum and accelerated air incorporation into light

batches.

Starts Mixer

Stops Mixer

Speed Selector

Time Selector

Raises and Lowers

Mixing Bowl

Displays Selected

Mix Speed

Displays

Mixing Time

– 8 –

Model HL662 (With Two Mix Speeds Plus Meat Grind, Cheese Shred, Vegetable Slice Speeds)

Model HL662 Mixer Speeds

SPEED 1 (Slow) This speed is for heavy mixtures such as pizza dough.

SPEED 2 (Low) This speed is for developing pizza dough.

MEAT GRIND This speed is for grinding meat.

CHEESE SHRED This speed is for shredding cheese.

VEGETABLE SLICE This speed is for slicing vegetables.

Starts Mixer

Stops Mixer

Displays Selected

Mix Speed

Displays

Mixing Time

Speed Selector

Time Selector

Raises and Lowers

Mixing Bowl

– 9 –

BOWL PLACEMENT

The bowl must be installed before the agitator is installed.

To install the bowl, fully lower the bowl support. Position bowl so the alignment pins on the left side of the

bowl support ﬁ t in the holes in the bowl. Swing the bowl into the locked position on bowl support.

AGITATOR

To install an agitator, the bowl must be on the bowl support and fully lowered.

To Install

1. Open the wire cage.

2. Place the agitator inside the bowl and line up the

horizontal slot on the agitator with the agitator shaft

pins.

3. Slide the agitator up the agitator shaft until it stops

and latches.

To Remove

1. Open the wire cage.

2. Lower the bowl by pressing and holding the down

arrow on the bowl switch.

3. Hold the agitator and pull the plunger of the agitator out

(Fig. 3). Slide agitator down off the agitator shaft.

POWER BOWL LIFT

CAUTION: Before lowering the bowl onto a bowl truck, always unlock bowl and swing bowl out

slightly.

To raise the bowl, the bowl must be in the locked position. Push and hold the up arrow on the bowl

switch.

To lower the bowl, push and hold the down arrow on the bowl switch.

To Raise the Bowl While Mixing

To raise the bowl while the agitator is mixing the product (when required by recipe or when using the Bowl

Scraper Attachment):

1. Close the wire cage, then select a mixing speed on the SPEED dial.

2. Select a count-down time or HOLD for continuous count-up mixing.

3. While pressing and holding the up arrow on the bowl switch, press and hold the START button.

The mixer runs only in stir speed while the bowl is rising.

4. When the bowl reaches the mix position, release the START button. The mixer automatically

changes to the selected mixing speed.

Fig. 3

– 10 –

PREPARE FOR MIXING

1. Place the mixing bowl on the bowl support.

2. Pour ingredients into the bowl.

3. Swing the bowl back to the locked position.

4. Place the agitator inside the bowl, then attach

it to the agitator shaft (Fig. 4).

5. Return the wire cage to front-center position.

6. Push and hold the up arrow on the bowl switch

until the bowl reaches the mix position and stops.

7. The mixer is now ready for mixing. (See Timer

Operation.)

TIMER OPERATION

Using the Count-Up Mode (Continuous Mixing)

1. Turn the SPEED dial to select a mix speed (the SPEED setting can be changed at any time dur-

ing the mixing operation).

NOTE : STIR is to be used for incorporating ingredients. Do not use to develop dough products.

2. Set the timer on hold by turning the TIME selector counterclockwise until "Hold" appears in the

TIME window.

3. Press the START button to begin mixing. The timer starts counting forward from 00:00.

NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the mix-

ing operation, close the wire cage and press the START button.

4. Use the STOP button to stop the mixer; the mixing time is displayed in the TIME window.

5. Press the start button to resume mixing if needed.

NOTE: When the timer reaches 20:00 minutes, it will rollover to 00:01 and continue counting until

the STOP button is pressed.

Wire Cage

Dough Hook

Accessory

Fig. 4

– 11 –

Using the Count-Down Mode (Timed Mixing)

1. Turn the SPEED dial to select a mix speed.

a. If the count-up mode was used for the previous batch, the desired time needs to be entered.

b. If the count-down mode was used for the previous batch, the previous time will be displayed. If

a different time is needed, turn the TIME selector to the desired time.

2. Press the START button to begin mixing; the timer starts counting down from the set time.

a. To stop the mixer at any time, press the STOP button. To resume mixing, press the START

button. For example: The mixer is started at SPEED 1 for 30 seconds and is stopped after 10

seconds. Pressing the START button will resume the mixing operation.

b. If the mixer is stopped and a new time setting is entered, pressing the START button saves

the new time setting on the current speed selection. For example: The mixer is started at

SPEED 1 for 30 seconds and is stopped after 10 seconds. A new time is entered by turning

the TIME selector. The new time will replace the initial 30 seconds for SPEED 1 after the

START button is pressed.

c. If the time is changed while mixing, the mixer will operate until the new time expires. The

adjustment to the time will not be stored.

d. If speed is changed while mixing, the time will change to the previous time for the selected

speed and count down.

NOTE: If the wire cage is opened at any time, the mixing operation will stop. To resume the mix-

ing operation, close the wire cage and press the START button.

3. When the timer reaches 00:00, the mixer stops; a beeper sounds for 3 seconds. The count-down

timer displays the last-entered time.

OPERATING NOTES

• STIR is to be used for incorporating ingredients. Do not use it to develop dough products.

• If the mixer is stopped during a mixing operation, the timer also stops. The timer starts again

where it left off when the START button is pressed.

• The SPEED window will display the SPEED dial's current speed selection. Turn the Time selector

clockwise to take the mixer out of the hold mode.

– 12 –

UNLOADING

1. Unlock the bowl and swing-out slightly. Press and hold the down arrow on the bowl switch to

lower the bowl.

2. Open the wire cage assembly.

3. Remove the agitator from the agitator shaft.

4. Remove the bowl from the bowl support.

WIRE CAGE (Fig. 5)

The wire cage can be rotated out of the way to add ingredients or to access the bowl and agitator.

Note how the grooves on the nylon retainer shoes allow the Wire Cage to ride around the circular ridge

of the planetary drip cup.

• To open the wire cage, rotate it to your left.

• To close the wire cage, rotate it to your right until it stops in the front-center, closed position.

NOTE: The wire cage must be returned to the closed position for the mixer to operate.

Front-Center Retainer Shoe

Drip Cup-

Splash

Guard

Assembly

Wire Cage Front-Center Position

Rear Retainer Shoe

Circular Ridge on

Planetary Drip Cup

Wire Cage Rotated Left

Fig. 5

– 13 –

Remove and Clean Wire Cage (Fig. 6)

1. Lower the bowl. Remove the agitator and bowl.

2. While holding the wire cage securely with both hands, rotate it to your left until the front-center

retainer shoe reaches the gap in the circular ridge of the planetary drip cup.

3. Lower the front of the wire cage and move the wire cage slightly to the rear so the rear retainer

shoes clear the ridge of the drip cup. The wire cage can now be removed.

4. Wash the wire cage in a sink, rinse with clear water, and dry with a clean cloth.

5. The stainless steel splash guard can be wiped off and/or washed with a cloth or sponge using

warm, soapy water. Rinse with clear water and dry with a clean cloth.

Reinstall Wire Cage

1. Position the ring of the wire cage so the front-center retainer shoe is positioned below the gap in

the circular ridge of the planetary drip cup.

2. Position the grooves so the rear retainer shoes straddle the circular ridge on the planetary drip

cup.

3. Lift the front of the wire cage so the front-center retainer shoe passes up through the gap in the

circular ridge on the planetary drip cup.

4. Rotate the wire cage to your right until all three retainer shoes straddle the ridge on the drip cup.

5. Continue rotating the wire cage so the opening is to the front of the mixer (to install the agitators)

or until it stops at the front-center position.

AGITATORS AND ATTACHMENTS

Attachments for attachment hub and agitators are covered in a separate Hobart Legacy

Mixer Use and

Application Handbook on the Mixer Operator Information CD. Follow the instructions accordingly.

Front-Center Retainer Shoe

Gap in Circular Ridge

Fig. 6

– 14 –

CLEANING

DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /

tagout procedures.

New mixer bowls and accessories (beaters, whips and dough arms) should be thoroughly washed with hot

water and a mild soap solution, rinsed with either a mild soda or vinegar solution and thoroughly rinsed with

clear water before being used. This cleaning procedure should also be followed for bowls and agitators

before whipping egg whites or whole eggs.

The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it should be washed

with a clean, damp cloth. The base allows ample room for cleaning under the mixer. The apron (Fig. 2,

page 6) may be removed for cleaning by loosening the thumb screws.

The drip cup-splash guard assembly (Fig. 2, page 6) should be removed periodically and wiped clean.

For cleaning the Wire Cage refer to page 13.

– 15 –

MAINTENANCE

DISCONNECT the ELECTRICAL POWER to the machine and follow lockout /

tagout procedures.

LUBRICATION

Slideway

The slideways (Fig. 7) should be lubricated approximately twice a year. To reach these areas, fully lower

the bowl support and remove the apron, which is secured by thumb screws. Wipe a thin coat of Lubriplate

630AA on the bowl pad area of the bowl supports and on each slideway. Install the apron.

Planetary Seal

Occasionally, the planetary seal (Fig. 7) may become dry and begin to squeak. To correct this, work a little

lubrication (mineral oil) under the lip of the seal.

Planetary Seal

Slideway

Fig. 7

– 16 –

Transmission

To check the oil level, remove the top cover, which is secured by two screws. Remove the Transmission Fill

Plug (Fig. 8) and check the oil level. If the oil level is below the line on the oil dipstick, add a small amount

of the recommended transmission oil until it returns to the proper level. Do not overﬁ ll the transmission, as

leakage may result. Contact your local Hobart Service Ofﬁ ce for the recommended transmission oil.

ADJUSTMENTS

Agitator Clearance

The agitator clearance should be checked periodically. The agitator must not touch the bowl, and the

maximum clearance between the bottom of the bowl and the B ﬂ at beater is 1/8" (3 mm); the maximum

clearance between the bottom of the bowl and the ED dough arm is 5/16" (8 mm).

Install a bowl and agitator (e.g., beater). If the bowl and beater come into contact before the bowl support

reaches its stop, adjust the stop screw. Refer to Adjust the Bowl/Agitator Clearance, page 17.

Transmission Fill Plug/Oil Dipstick

Fig. 8

– 17 –

Measure Clearance

Pour enough ﬂ our in the bowl to cover the bottom of the bowl where the beater travels. With the bowl fully

raised (beater should not touch the bottom of the bowl), brieﬂ y run the mixer at the lowest speed.

Turn off the mixer, disconnect the electrical power supply, and measure the depth of ﬂ our where the

beater has traced a path. This measurement should be taken at several points around the bowl to assure

accuracy.

Adjust the Bowl/Agitator Clearance

• Remove the apron (which is secured by thumbscrews).

• Adjust the stop screw on right side.

- Loosen the bottom locking nut, (Fig. 9) and turn

the stop screw counterclockwise to increase

the clearance or clockwise to decrease the

clearance.

- Tighten the locking nut while holding the stop

screw.

• After the adjustments are made, replace the apron

and secure it with the thumbscrews.

• Reconnect the electrical power supply.

• Carefully operate the bowl lift several times to

check the adjustment.

Bowl Lock Lever

• Occassionally debris may collect and cause

the lever to move slowly.

• Pour very warm water around lock pin to ﬂ ush

out food particles that may have collected

there. The water should ﬂ ow through, around

the pin. Be sure to have a cloth or dish under

to bowl support to catch the water and food

particles.

• Lubricate the pin with a thin coat of lubriplate

630AA.

Stop Screw &

Locking Nut

Fig. 9

Bowl Lock Lever

– 18 –

TROUBLESHOOTING

Symptoms Possible Causes

Mixer will not start. Circuit protector is in open position - check fuse or

disconnect switch.

Mixer is overloaded.

Wire cage is not in the closed position.

Bowl is not in closed (locked) position.

Agitator touches bowl. Bowl is not in closed (locked) position.

Improper agitator clearance - see Maintenance for

adjustment procedure.

Agitator is not installed properly.

Planetary seal squeaks. Seal requires occasional lubrication - see Maintenance.

Timer displays error code (ErXX). If the error code is ﬂ ashing - wait for mixer to clear error

condition. If mixer continues to stop and timer displays

ﬂ ashing error code, disconnect electrical power from

mixer for 1 minute, then reconnect. If symptoms still exist,

contact your local Hobart Service ofﬁ ce.

– 19 –

SERVICE

If service is needed on this equipment, contact your local Hobart Service ofﬁ ce.

– 20 –

F45239 (December 2013) PRINTED IN U.S.A.

NOTES

La page charge ...

Hobart Legasy HL600 Manuel utilisateur

Marque: Hobart

Modèle: Legasy HL600

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hobart Legasy HL600 User manual

Hobart Legasy HL600 Manuel utilisateur

Ce manuel convient également à

Hobart Legasy HL600 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents