Jacuzzi (2014) J-300™ Le manuel du propriétaire

OWNER’S MANUAL

J-300

™

Collection

J - 315

J - 325

J - 335

J - 345

J - 355

J - 365

J - 375

J - 385

2530-398A Rev. B

Attention New Spa Owner!

Congratulations on the purchase of your new Jacuzzi

®

spa! The following is a

list of automated functions performed by your spa. These functions are listed

below in an attempt to alleviate any operational concerns you may have during

the rst 24 hours of ownership! Also listed below are important maintenance

recommendations you should observe on a regular basis to protect your new

investment.

Automated Operations

Approximately two minutes after power is applied to the spa, the rst ltration/

heating cycle turns on pump 1. An automatic “blow-out” function also activates

pump 2 (if equipped) for a period of one minute to ush all lines. Then, after one

minute, pump 2 turns off and pump 1 continues to operate for the duration of the

cycle.

Note: This function only occurs during the rst ltration/heating cycle each day.

Maintain Healthy Spa Water

Always maintain your spa’s water chemistry within the following parameters:

With CLEARRAY® Without CLEARRAY®

pH 7.4-7.6 7.4-7.6

Free Chlorine no less than 1.0 ppm 3.0-4.0 ppm

Free Bromine no less than 2.0 ppm 2.0-4.0 ppm

Total Alkalinity 100-150 ppm 100-150 ppm

Calcium Hardness 150-250 ppm 150-250 ppm

IMPORTANT: CLEARRAY® Water Purication System is factory installed. If

the CLEARRAY® system is altered or is not operating efciently then follow

the “without CLEARRAY®” water chemistry parameters as dened by the

Association of Pool and Spa Professionals. CLEARRAY® requires an annual

bulb replacement to properly sanitize your water.

!

TO DECREASE RISK OF INFECTION OR DISEASE! Always maintain

your spas lter as outlined below to ensure healthy spa water. Refer page 43

“Water Quality Maintenance” for additional information.

Required Filter Maintenance

Your new spa is equipped with an advanced water ltration system that provides

unsurpassed water quality! To ensure maximum water quality at all times, you

should clean both lter cartridges every month, or earlier as necessary. See page

36 for detailed lter cartridge cleaning/replacement instructions.

Required Water Replacement

!

TO DECREASE RISK OF INFECTION OR DISEASE!

You should replace

the spa’s water every 3 months. The frequency depends on a number of variables

including frequency of use, number of users, and attention paid to water quality

maintenance. You will know it is time for a change when you cannot control

sudsing and/or you can no longer get

the normal feel or sparkle to the water,

even though the key water balance measurements are all within the proper

parameters. See page 43 for additional information.

J-300

Table of Contents

1.0 Important Spa Owner Information.....................................1

2.0 FCC Notice ..........................................................................1

3.0 Important Safety Instructions for all Spa Owners ...........2

3.1 Entrapment Risk ...................................................................6

3.2 Hyperthermia ........................................................................7

3.3 Important Additional CSA Safety Instructions

(Canada Only) ......................................................................8

3.4 General Electrical Safety Instructions ...................................8

4.0 Choosing A Location ..........................................................9

4.1 Outdoor Location ................................................................10

4.2 Indoor Location ...................................................................10

5.0 General Electrical Safety Instructions ............................11

6.0 Power Requirements ........................................................12

7.0 Electrical Wiring Instructions ..........................................15

8.0 Spa Fill Up Procedure ......................................................18

9.0 Control Functions .............................................................23

9.1 Control Panel ......................................................................23

9.2 General Spa Features And Controls ...................................24

10.0 Operating Instructions .....................................................25

10.1 Setting Water Temperature ................................................25

10.2 Activate Jet Pumps .............................................................26

10.3 Light On/Off Button .............................................................26

10.4 Light Mode Button...............................................................26

10.5 Jets .....................................................................................26

10.6 Selecting Desired Massage Action .....................................27

10.7 Waterfall Feature ................................................................27

10.8 Air Controls .........................................................................27

10.9 Optional BLUEWAVE® Spa Stereo System .......................27

11.0 Menu Features and Programming Instructions .............28

11.1 Primary Filtration Menu.......................................................29

11.2 Programming the Primary Filtration Cycle ..........................30

11.3 Programming the Change Filter Timer ...............................31

11.4 Secondary Filtration Menu ..................................................32

11.5 Programming the Secondary Filtration Cycle .....................32

11.6 Programming the CLEARRAY Bulb Replacement Timer ...33

11.7 Economy Menu ...................................................................33

11.8 Programming the Economy Mode ......................................34

J-300

11.9 Lock Menu ..........................................................................34

11.10 Programming the Lock Modes ............................................35

11.11 Top Menu Lock ...................................................................35

11.12 Programming the Top Menu Lock Feature .........................35

12.0 Spa Maintenance ..............................................................36

12.1 Cleaning The Filters............................................................36

12.2 DrainingandRelling..........................................................39

12.3 Pillow Care..........................................................................40

12.4 Cleaning The Spa Interior ...................................................40

12.5 Vinyl Cover Care and Maintenance ....................................40

12.6 Tool Free Access Door .......................................................41

12.7 Maintaining The Synthetic Cabinet .....................................41

12.8 Winterizing ..........................................................................42

12.9 Restarting Your Spa in Cold Weather .................................43

13.0 Water Quality Maintenance ..............................................43

13.1 pH Control...........................................................................44

13.2 Sanitizing ............................................................................44

13.3 CLEARRAY®(Ultraviolet)WaterPuricationSystem ........45

13.4 CLEARRAY® Bulb Replacement and

Quartz Tube Maintenance ..................................................46

14.0 Error Conditions/Error Messages ...................................49

14.1 Summer Logic.....................................................................49

14.2 Panel Displays COL ............................................................49

14.3 Panel Displays ICE .............................................................49

14.4 Panel Displays SN1 ............................................................49

14.5 Panel Displays SN2 ............................................................49

14.6 Panel Displays BLB ............................................................49

14.7 Panel Flashes FL1 or FL2 ..................................................50

14.8 Panel Displays OH..............................................................50

14.9 Panel Displays (- - -) ...........................................................50

14.10 Panel Displays CF ..............................................................51

15.0 Troubleshooting Procedures ...........................................51

15.1 None of the Components Operate (e.g. Pump, Light) ........51

15.2 Pump Does Not Operate ....................................................51

15.3 Poor Jet Action ...................................................................52

15.4 Water is Too Hot .................................................................52

15.5 No Heat...............................................................................52

J-300

16.0 Circuit Board Diagrams....................................................53

16.1 North American J-335, J-345, J-355, J-365, J

-375 and J-385 Dedicated Power Models (60 Hz) ..............53

16.2 North American J-315 and J-325 Convertible

Power Models (60 Hz) ........................................................54

16.3 Export J-335, J-345, J-355, J-365, J-375 and

J-385 Models (50 Hz) .........................................................55

16.4 Export J-315 and J-325 Models (50 Hz) .............................56

17.0 Optional BLUEWAVE® Spa Stereo System ....................57

17.1 Pairing the Remote and Stereo ..........................................58

17.2 Audio Settings.....................................................................58

17.3 Wireless Remote Control Functions ...................................60

17.4 Electronic Device Connections and Functions ...................61

17.5 Wireless Remote Battery Replacement Procedure ............64

17.6 BLUEWAVE®SpaStereoSystemSpecications ..............64

17.7 Stereo Cautions ..................................................................65

J-300

1

J-300

1.0 Important Spa Owner Information

Your Jacuzzi J-300 Collection spa is constructed to the highest standards

and is capable of providing many years of trouble-free use. However,

because heat retentive materials are utilized to insulate the spa for

efcient operation, an uncovered spa surface and wall ttings directly

exposed to sunlight and high temperatures for an extended period are

subject to permanent damage. Damage caused by exposing the spa

to this abuse is not covered under warranty. We recommend that you

always keep the spa full of water when it is exposed to direct sunlight

and that you keep the Jacuzzi premium insulating cover in place at

all times when the spa is not in use. Read and carefully follow the

requirements for your spa’s support base found in Section 4.0 titled,

“Choosing A Location” (page 9).

Jacuzzi constantly strives to offer the nest spas available,

therefore modications and enhancements may be made which

affect the specications, illustrations and/or instructions contained

herein.

2.0 FCC Notice

This equipment has been tested and found to comply with the limits for

a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

1. Rearrange or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from the

circuit connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modications not expressly approved by the party

responsible for FCC compliance could void the user’s authority to

operate this equipment.

2

J-300

3.0 Important Safety Instructions for all Spa Owners

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY!

This spa was manufactured to meet the standards and specications

outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB

Safety Act). When installing and using this spa, basic safety precautions

should always be followed, including:

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Extreme caution must be exercised to prevent unauthorized access

by children.

• To avoid accidents, ensure that children do not use this spa unless

supervised at all times. Adult supervision is a critical safety factor in

preventing children from drowning.

• Use the straps and clip tie downs to secure the spa cover when not

in use. This will help discourage unsupervised children from entering

the spa. Keep the spa cover secure in high-wind conditions.

• There is no representation that the cover, clip tie-downs, or actual

locks will prevent access to the spa.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Keep hair, loose articles of clothing or hanging jewelry away from

suction ttings, rotating jets or other moving components to avoid

entrapment that could lead to drowning or severe injury.

• Never use the spa unless all suction guards, lter, lter lid, or

skimmer assembly are installed to prevent body and/or hair

entrapment.

• Never operate or use the spa if the lter, lter lid, or skimmer

assembly are broken or any part of the skimmer assembly is missing.

Please contact your dealer or nearest service center for service.

• The suction ttings and suction covers in this spa are sized to match

the specic water ow created by the pump(s). If it is necessary to

replace the suction ttings, suction covers or pump(s), be sure that

the ow rates are compatible and are in compliance with the VGB

Safety Act.

• Never replace a suction tting or suction cover with one rated less

than the ow rate marked on the original suction tting. Using

improper suction ttings or suction covers can create a body or hair

suction entrapment hazard that may lead to drowning or severe

injury.

3.

!

DANGER: RISK OF SEVERE INJURY FROM ELECTRIC

SHOCK OR DEATH FROM ELECTROCUTION!

• Install the spa at least 5 feet (1.5m), from all metal surfaces. As an

alternative, a spa may be installed within 5 feet of metal surfaces

if each metal surface is permanently connected (bonded) by a

minimum No. 8 AWG (8.4 mm²) solid copper conductor attached

to the wire connector on the grounding lug, inside the equipment

compartment on the equipment box.

3

J-300

• A grounding wire connector is provided on this unit to connect a

minimum No. 8 AWG (8.4 mm²) solid copper conductor between

this unit and any metal equipment, metal enclosures of electrical

equipment, metal water pipe, or conduit within 5 feet (1.5m) of the

unit.

• Never permit any electrical appliance, such as a light, telephone,

radio, television, etc. within 5 feet (1.5m) of a spa unless such

appliances are built-in by the manufacturer.

• Never bring any electrical appliances into or near the spa.

• Never operate any electrical appliances from inside the spa or when

you are wet.

• The electrical supply for this product must include a suitably rated

switch or circuit breaker to open all ungrounded supply conductors

to comply with section 422-20 of the National Electrical Code/USA,

ANSI/NFPA 70. The disconnecting means must be readily accessible

and visible to the spa occupant but installed at least 5 feet (1.5m),

from the spa.

• The electrical circuit supplied for the hot tub must include a suitable

ground fault circuit interrupter (GFCI) as required by NEC Article

680-42.

4.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Extreme caution must be exercised to prevent diving or jumping

into the spa or slipping and falling, which could result in

unconsciousness, drowning, or serious injury. Remember that wet

surfaces can be very slippery.

• Never stand, walk or sit on the top railing of the spa.

5.

!

WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)

CAUSING SEVERE INJURY, BURNS, WELTS OR DEATH!

• Water temperature in excess of 104°F (40°C) may be injurious to

your health.

• Refer to Section 3.2 Hyperthermia for specic causes and symptoms

of this condition.

• The water in the spa should never exceed 104°F (40°C). Water

temperatures between 100°F (38°C) and 104°F (40°C) are

considered safe for a healthy adult.

• Lower water temperatures are recommended for young children

(children are especially sensitive to hot water) and when spa use

may exceed 10 minutes.

• The Consumer Products Safety Commission/USA has stated that the

water temperature in a spa should not exceed 104°F (40°C).

• Always test the spa water temperature before entering the spa.

The user should measure the water temperature with an accurate

thermometer since the tolerance of water temperature-regulating

devices may vary as much as +/- 5°F (2°C).

4

J-300

6.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Since excessive water temperatures have a high potential for

causing fetal damage during the early months of pregnancy, if

pregnant or possibly pregnant, consult your physician before using a

spa.

• Pregnant or possibly pregnant women should limit spa water

temperatures to 100°F (38°C).

• Persons suffering from obesity or a medical history of heart disease,

low or high blood pressure, circulatory system problems, diabetes,

infectious diseases or immune deciency syndromes should consult

a physician before using a spa.

• If you experience breathing difculties in association with using or

operating your spa, discontinue use and consult your physician.

• Persons using medication should consult a physician before using

a spa since some medication may induce drowsiness, while other

medication may affect heart rate, blood pressure, and circulation.

• Persons suffering from any condition requiring medical treatment, the

elderly, or infants should consult with a physician before using a spa.

• The use of alcohol, drugs, or medication before or during spa use

may lead to unconsciousness with the possibility of drowning.

7.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Prolonged immersion in a spa may be injurious to your health.

• Observe a reasonable time limit when using the spa. Exposures

at higher temperatures can cause high body temperature (over-

heating). Symptoms may include dizziness, nausea, fainting,

drowsiness, and reduced awareness. These effects could possibly

result in drowning or serious injury.

• Never use a spa immediately following strenuous exercise. Enter

and exit the spa slowly. Wet surfaces can be slippery.

8.

!

WARNING: TO DECREASE RISK OF INFECTION OR DIS-

EASE!

• To reduce the risk of contracting a waterborne

illness (e.g. an infec-

tion, bacteria or virus) and/or respiratory ailments

, maintain water

chemistry within the parameters listed on the inside cover of this

manual and consult with a licensed engineer regarding proper venti-

lation if installed indoors or in an enclosed area.

• People with infectious diseases should not use a spa to avoid water

contamination, which could result in spreading infections to others.

• Always shower before and after using your spa. Maintain water

chemistry in accordance with manufacturer’s instructions. Failure to

do so may result in contracting a waterborne

illness (e.g. an infection,

bacteria or virus).

5

J-300

9.

!

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the risk of

contracting a waterborne

illness (e.g. an infection, bacteria or virus)

and/or respiratory ailments

that could be present in the air or water.

Consult a licensed architect or building contractor to determine your

specic needs if installing your hot tub indoors.

10. CAUTION: TO DECREASE RISK OF PRODUCT DAMAGE.

• Maintain water chemistry in accordance with manufacturer’s

instructions.

• Proper chemical maintenance of spa water is necessary to maintain

safe water and prevent possible damage to spa components.

11.

!

WARNING: RISK OF SEVERE INJURY OR DEATH! The

appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience or knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

12. NOTE: This spa is not intended nor designed to be used in a

commercial or public application. The spa buyer shall determine

whether there are any code restrictions on the use or installation

of this spa since local code requirements vary from one locality to

another.

Hot Tub Safety Literature

To ensure you have a safe and enjoyable hot tub experience,

learn all you can about hot tub safety and emergency procedures.

Especially useful are the brochures listed below:

• Children Aren’t Waterproof

• Pool and Spa Emergency Procedures For Infants and

Children

• Layers of Protection

• The Sensible Way to Enjoy Your Spa or Hot Tub

The Association of Pool and Spa Professionals publishes these

brochures. To acquire a brochure:

• Ask your hot tub dealer (they may have copies)

• Go to http://apsp.org

• Conduct your own search on the internet

• Write to the following address:

The Association of Pool and Spa Professionals

2111 Eisenhower Avenue

Alexandria VA 22314

703.838.0083

6

J-300

3.1 Entrapment Risk

The Consumer Products Safety Commission/USA has reported that

users of pools and spas have become entrapped (stuck) to drain and/or

suction ttings causing death, drowning, or serious injury (see diagram

below). This spa was manufactured to meet the standards and specica-

tions outlined in the “Virginia Graeme Baker Pool and Spa Safety Act”

(VGB Safety Act). Entrapment risk can be minimized if proper precau-

tions are taken.

DANGER: RISK OF PERSONAL INJURY OR DEATH!

Never operate the spa if a suction tting, suction cover, lter,

lter lid or skimmer assembly are broken, damaged or miss-

ing.

!

Note: Suction covers must be replaced every 5 years.

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Hair entrapment: May occur if hair is entangled, knotted or snagged

in a drain suction or skimmer assembly. This has been reported in

persons who when submerge themselves underwater, allowing hair

to come close and/or within the reach of the suction fittings, suction

covers or skimmer assembly.

• Keep hair away from suction ttings, suction covers, lter, lter lid or

skimmer assembly.

• Children are at risk for hair entrapment if swimming under water.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Limb entrapment: May occur when a limb becomes entrapped,

inserted or sucked into a suction or outlet opening.

• Always keep suction ttings, suction covers, lter, lter lid or skimmer

assembly in place when operating to avoid limb entrapment.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

Suction Fittings,

Suction Covers

(locations vary

by models)

Filter, Filter Lid,

Skimmer As-

sembly (location

and style vary by

models)

7

J-300

3.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Body entrapment: May occur when part of the torso becomes

entrapped, inserted or sucked into a suction or outlet opening.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

4.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Evisceration (disembowelment) entrapment: May occur when the

buttocks becomes entrapped, inserted or sucked into a suction or

outlet opening.

• Never sit on suction ttings, suction covers, lter, lter lid or skimmer

assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

5.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Mechanical entrapment: May occur when jewelry, swimsuit, or

hair accessories become entangled, knotted or snagged in a drain

suction or skimmer assembly.

• Never allow your jewelry, swimsuit, or hair accessories to come close

to the suction ttings, suction covers or skimmer assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

3.2 Hyperthermia

Prolonged immersion in hot water may induce hyperthermia (over-

heating). The use of alcohol or drugs can greatly increase the risk of fatal

hyperthermia in spas. A description of the causes, symptoms, and effects

of hyperthermia are as follows:

Hyperthermia occurs when the internal temperature of the body reaches

a level several degrees above the normal body temperature of 98.6°F

(37°C). The symptoms of hyperthermia include drowsiness, lethargy

(fatigue), and an increase in the internal temperature of the body (feeling

of being too hot). The effects of hyperthermia include:

• Unawareness of impending hazard;

• Failure to perceive heat;

• Failure to recognize the need to exit spa;

• Physical inability to exit spa;

• Fetal damage in pregnant women; and

• Unconsciousness and DANGER of drowning.

A Warning Sign is provided in your warranty packet. Please install at

a location near your spa, where it is visible to users of the spa. For

additional or replacement Warning Signs please contact your local

Jacuzzi dealer and reference item number #6530-082.

8

J-300

3.3 Important Additional CSA Safety Instructions (Canada Only)

When using this electrical equipment, basic safety precautions should

always be followed, including the following:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. A green colored terminal or a terminal marked G, Gr, Ground,

Grounding or the symbol* is located inside the supply terminal box

or compartment. To reduce the risk of electric shock, this terminal

must be connected to the grounding means provided in the electric

supply service panel with a continuous copper wire equivalent in size

to the circuit conductors that supply this equipment (*IEC Publication

417, Symbol 5019).

3. At least two lugs marked “Bonding Lugs” are provided on the

external surface or on the inside of the supply terminal box/

compartment. To reduce the risk of electric shock, connect the local

common bonding grid in the area of the spa to these terminals with

an insulated or bare copper conductor not smaller than No. 6 AWG

(10 mm²).

4. All eld installed metal components such as rails, ladders, drains or

other similar hardware within 10 feet (3m) of the spa shall be bonded

to the equipment grounding buss with copper conductors not smaller

than No. 6 AWG (10 mm

2

).

5. SAVE THESE INSTRUCTIONS.

3.4 General Electrical Safety Instructions

Your new Jacuzzi spa is equipped with a “state-of-the-art” equipment

system. It contains the most advanced safety and self-protective

equipment in the industry. Nonetheless, this spa must be installed

properly to ensure dependable usage. Please contact your local Jacuzzi

dealer or local building department should you have any questions

regarding your installation.

Proper grounding is extremely important. Jacuzzi spas are equipped with

a current collector system. A pressure wire connector is provided on the

surface of the control box, located outside the equipment door (Figure

B, page 17) to permit connection of a bonding wire between this point

and any ground metal equipment, metal water pipe or conduit within 5

feet (1.5m) of the spa, or copper clad grounding rod buried within 5 feet

(1.5m) of the spa. Bonding wire must be at least No. 8 AWG (8.4 mm²)

solid copper wire. This is a most important safety assurance feature.

Before installing your spa, check with your local building department to

insure installation conforms to local building codes.

9

J-300

4.0 Choosing A Location

WARNING: For spas that are to rest on balconies, roofs

or other platforms not specically tied into main struc-

tural support, consult a professional Structural Engineer

with experience in this type of application.

!

The spa must be installed in such a manner as to provide drainage away

from it. Placing the spa in a depression without provisions for proper

drainage could allow rain, overow and other casual water to ood the

equipment and create a wet condition in which it would sit in. For spas

which will be recessed into a oor or deck, install so as to permit access

to the equipment, either from above or below, for servicing. Make certain

that there are no obstructions which would prevent removal of all side

cabinet side panels and access to the jet components, especially on the

side with the equipment bay.

CAUTION: If the spa is indoors or located in an enclosed area,

proper ventilation should be discussed with an Engineer or authority

competent enough to understand the necessary provisions needed

to vent moist or heated air and air associated with chemical odors

outdoors. When the spa is in use considerable amounts of

moisture will escape potentially causing mold and mildew. This

can cause health risk. Over time, this can damage certain surfaces,

surroundings, and equipment.

IMPORTANT: Because of the combined weight of the spa, water

and users, it is extremely important that the base upon which the

spa rests be smooth, at, level and capable of uniformly supporting

this weight, without shifting or settling, for the entire time the spa is

in place. If the spa is placed on a surface which does not meet these

requirements, damage to the skirt and/or the spa shell may result.

Damage caused by improper support is not covered under warranty.

It is the responsibility of the spa owner to assure the integrity of the

support over time. We recommend a poured, reinforced concrete

slab with a minimum thickness of 4 inches (10 cm). Wood deck-

ing is also acceptable provided it is constructed so that it meets the

requirements outlined above.

!

10

J-300

4.1 Outdoor Location

In selecting the ideal outdoor location for your spa, we suggest that you

take into consideration:

• The proximity to changing area and shelter (especially in colder

weather).

• The pathway to and from your spa (this should be free of debris so

that dirt and leaves are not easily tracked into the spa).

• The closeness to trees and shrubbery (remember that leaves and

birds could create extra work in keeping the spa clean).

• A sheltered environment (less wind and weather exposure can result

in lowered operation and maintenance costs).

• The overall enhancement of your environment. It is preferable not to

place the spa under an unguttered roof overhang since run-off water

will shorten the life expectancy of the spa cover.

• For spas that are to rest on balconies, roofs or other platforms not

specically tied into main structural support, consult a professional

Structural Engineer with experience in this type of application.

• In the unlikely event that you should ever need to access or gain

entry to any portion of the spa for servicing, it is highly recommended

that you plan your outdoor installation to provide full access to the

entire spa. Please take this into consideration when placing the spa

in a deck or enclosed by a surrounding.

• Consider locating your spa away from any reective surface or glass

to prevent any damage to the synthetic skirt.

• Do not shim the spa. To ensure proper support the spa must sit at

on the intended foundation.

4.2 Indoor Location

For indoor installations many factors need to be considered before

installing a spa indoors:

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the

risk of contracting a waterborne

illness (e.g. an infection, bac-

teria or virus) and/or respiratory ailments

that could be pres-

ent in the air or water. Consult a licensed architect or building

contractor to determine your specic needs if installing your

hot tub indoors.

!

• Proper Foundation: Consult a Structural Engineer when

considering a foundation that will adequately support the spa

the entire time it is in place. Proper support is critical especially

if the spa is to rest on a second story or higher. For spas that are

to rest on balconies, roofs or other platforms not specically tied

into the main structural support, you should consult a professional

Structural Engineer with experience in this type of application.

11

J-300

• Proper Drainage: It is extremely important to have in place

measures to sufciently handle excessive water spillage. Be

sure the ooring in which the spa rests on has adequate drainage

and can handle the entire contents of the spa. Be sure to make

provisions for ceilings and other structures that may be below the

spas installation. Areas around your spa can become wet or moist so

all ooring and subsequent furniture, walls and adjacent structures

should be able to withstand or resist water and moisture.

• Proper Ventilation: Proper ventilation should be discussed with

an Engineer or authority competent enough to understand the

necessary provisions needed to vent moist or heated air and air

associated with chemical odors outdoors. When the spa is in use

considerable amounts of moisture will escape, potentially causing

mold and mildew over time which can damage certain surfaces and/

or surroundings.

• Sufcient Access: In the unlikely event that you should ever need

to access or gain entry to any portion of the spa for servicing, it is

highly recommended that you plan your indoor installation to provide

full access to the entire spa.

• Warranty: Damage caused by not following these guidelines or any

improper installation not in accordance to local codes or authorities is

not covered under the spas warranty. Please consult your local state

or city building ordinances.

• Do not shim the spa. To ensure proper support the spa must sit at

on the intended foundation.

5.0 General Electrical Safety Instructions

Your new Jacuzzi spa is equipped with a “state-of-the-art”

equipment system. It contains the most advanced safety

and self-protective equipment in the industry.

Nonetheless, this spa must be installed properly to insure

dependable usage. Please contact your dealer or local

building department should you have any questions regarding your

installation.

Proper grounding is extremely important. Jacuzzi spas are equipped with

a current collector system. A pressure wire connector is provided on the

surface of the control box, located outside the equipment door (Figure

B, page 17) to permit connection of a bonding wire between this point

and any ground metal equipment, metal water pipe or conduit within 5

feet (1.5m) of the spa, or copper clad grounding rod buried within 5 feet

12

J-300

(1.5m) of the spa. Bonding wire must be at least No. 8 AWG (8.4 mm²)

solid copper wire. This is a most important safety assurance feature.

Before installing this spa, check with the local building department to

insure installation conforms to local building codes.

120/240 Volt Convertible Models

A spa connected to a 120 VAC electrical service must be located close

enough to a grounded, grounding-type electrical outlet so that the

included 10 feet (3m) power cord can be plugged directly into it. DO NOT

USE AN EXTENSION CORD as this could cause damage to the spa’s

equipment due to insufcient voltage. The power supplied to this spa

must be a dedicated circuit with no other appliances or lights sharing the

power provided by the circuit.

6.0 Power Requirements

Jacuzzi spas are designed to provide optimum

performance and exibility of use when connected to the

maximum electrical service listed below. Minor circuit

board modications can be performed to allow your new

spa to accept an electrical service other than the factory

operation setting.

Note: Refer to pages 53-56 for circuit board conguration details or

contact your authorized Jacuzzi dealer.

North American J-335, J-345, J-355, J-365, J-375 and J-385 Models

(60 Hz)

240V/40A* 240V/50A** 240V/60A***

Circuit Breaker (2-Pole): 40A 50A 60A

Number of Wires: 3 3 3

Frequency: 60 Hz 60 Hz 60 Hz

Current Draw: 26A 36A 45A

*

In 40A conguration, the heater will not operate while either jets

pump is running.

**

In 50A conguration, the heater will not operate while both jets

pumps are running. This is the factory setting.

***

In 60A conguration the heater will operate while both jets pumps

are running.

13

J-300

North American J-315 and J-325 Convertible Models (60 Hz)

120V/15A† 240V/30A† 240V/40A

‡

Circuit Breaker: 15A, 1-Pole 30A, 2-Pole 40A

,

2-Pole

Number of Wires: 3 (15A GFCI

Cord US

Only*)

4 (Hard Wire

Only)

4 (Hard Wire

Only)

Frequency: 60 Hz 60 Hz 60 Hz

Current Draw: 12A 21A 30A

†

In 15A/30A conguration, the heater will not operate while the jets

pump is running. The factory setting is 120V/15A.

‡

In 40A conguration, remove jumper JP1-2 on the board, to allow the

heater to operate while the jets pump is running.

‡

Caution (For 4-wire 240 VAC Heater Operation): Move the red

wire on the main terminal strip (TB1) from position #1 to position

#3. Make certain wires are connected exactly as shown in Figure

D (page 17) before applying power. Failure to do so will result in

damage to the circuit board and/or related components and void the

manufacturer’s warranty.

14

J-300

Export J-335, J-345, J-355, J-365, J-375 and J-385 Models (50 Hz)

230V/20A* 230V/30A** 230V/40A***

RCD Breaker: 20A 30A 40A

Number of Wires: 3 3 3

Frequency: 50 Hz 50 Hz 50 Hz

Current Draw: 15A 23A 29A

Wattage: 3.5 kW 5.3 kW 6.7 kW

*

In 20A conguration, the heater will not operate while either jets

pump is running. This is the factory setting.

**

In 30A conguration, the heater will operate while one jets pump

is running.

***

In 40A conguration the heater will operate while both jets pumps

are running.

Export J-315 and J-325 Models (50 Hz)

230V/20A* 230V/30A**

RCD Breaker: 20A 30A

Number of Wires: 3 3

Frequency: 50 Hz 50 Hz

Current Draw: 15A 21A

Wattage: 3.5 kW 4.8 kW

*

In 20A conguration, the heater will not operate while the jets

pump is running. This is the factory setting.

**

In 30A conguration, the heater will operate while the jets pump is

running.

La page est en cours de chargement...

Jacuzzi (2014) J-300™ Le manuel du propriétaire

Jacuzzi (2014) J-300™ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents