Cal Spas Portable Spas Le manuel du propriétaire

Taper
Le manuel du propriétaire
LTR20061001, Rev. C
6/30/2006
CONTACT INFORMATION
For customer service, please contact your authorized dealer
immediately. If you need additional information and/or
assistance, please contact:
C.A.I. Customer Service Department
1462 East Ninth Street
Pomona, CA 91766
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
www.calspas.com
Copyright 2004, 2005, 2006 California Acrylic Industries, Inc. All rights reserved.
Duplication without written consent is strictly prohibited.
Cal Spas™, Adjustable Therapy System™, ATS™, Bio-Clean™, Cal Balance™, Cal
Entertainment System™, Cal Zone Quest 1000™ and Cal Zone Quest 2000™, Cal
Sweep™, Cal Select™, Fitness Spa Series™, Spa Cal™, and XL Heat Exchanger are
registered trademarks.
Due to continuous improvement programs, all models, operation, and/or specifications are
subject to change without prior notice.
LTR20061001, Rev. C
6/30/2006
Table of Contents
2006 Portable Spa Owner's Manual Page iii
Read This First!
Important Safety Instructions.....................................................................1
Basic Spa Information................................................................................2
Preparing for Your New Portable Spa
Planning the Best Location For Your Spa.................................................. 4
Preparing a Good Foundation for Your Portable Spa................................5
Electrical Set-up Before Delivery of Your Spa...........................................6
230 Volt Electrical Installation....................................................................7
Filling and Powering Up Your Portable Spa ..............................................9
Operating Your Spa
5005 Electronic Control Operation........................................................... 10
8005 Electronic Control Operation........................................................... 14
Auxiliary Control Operation......................................................................20
Adjustable Jets ........................................................................................20
Diverter Knobs.........................................................................................20
Air Venturis ..............................................................................................21
Adjustable Therapy System™ .................................................................21
Multi-Colored Spa Light Operation ..........................................................23
Spa Cover................................................................................................24
Aromatherapy ..........................................................................................24
Waterfalls.................................................................................................24
Removing and Reseating the Pillows ......................................................24
Draining Your Portable Spa.....................................................................25
Water Quality Maintenance
Cal Spas Clear Water Plan......................................................................27
Alternative Sanitation Options .................................................................27
Before You Begin.....................................................................................27
Chemical Overview..................................................................................28
Chemical Descriptions.............................................................................30
LTR20061001, Rev. C
Table of Contents
Page iv 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Traditional Chemical Start Up..................................................................34
Cal Zone Quest 2000 Ozonator Clear Water Plan ..................................37
Cal Clarity Automatic Bromine Generator Clear Water Plan ................... 38
Cal Inline Sanitation System Clear Water Plan .......................................40
Maintenance ............................................................................................42
Using the Cal Entertainment System
The Marine Grade Stereo Receiver.........................................................43
The DVD Multimedia Player ....................................................................44
Raising and Lowering the TV Monitor...................................................... 45
Universal Remote Control Operation.......................................................46
Appendix
Keeping Fit with your Cal Spa .................................................................48
Replacement Parts ..................................................................................51
Cal Spas™ Chemicals.............................................................................67
2006 Warranty Information ......................................................................68
Read This First!
2006 Portable Spa Owner's Manual Page 1
LTR20061001, Rev. C
Read This First!
Important Safety Instructions
When installing and using this electrical equipment, always follow basic safety precautions. Following
these instructions will help make your first spa session a pleasurable one.
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING: To reduce the risk of injury, do not allow children to use the spa unless they are supervised
at all times.
A licensed electrician may be required to upgrade your standard receptacle and/or circuit breaker.
DANGER -- RISK OF ACCIDENTAL DROWNING: Do not allow children to be in or around a spa
unless a responsible adult supervises them. Keep the spa cover on and locked when not in use. See
instructions enclosed with your cover for locking procedures.
DANGER -- RISK OF INJURY: The suction fittings in this spa are sized to match the specific water
flow created by the pump. Should the need arise to replace the suction fittings, or the pump, be sure the
flow rates are compatible.
DANGER -- RISK OF INJURY: Never operate the spa if the suction fitting or filter baskets are broken
or missing.
DANGER -- RISK OF INJURY: Never replace a suction fitting with one that is rated less than the flow
rate marked on the original suction fitting.
DANGER -- RISK OF ELECTRIC SHOCK: Install the spa at least 1.5 meters from all metal surfaces.
As an alternative, a spa may be installed within 1.5 meters of metal surfaces if each metal surface is
permanently bonded by a minimum #8 AWG solid copper conductor to the outside of the spa’s control
box.
DANGER -- RISK OF ELECTRIC SHOCK: Do not permit any external electrical appliances, such as
lights, telephones, radios, televisions, and etc., within 1.5 meters of the spa. Never attempt to operate any
electrical device from inside the spa. This does not apply to lights, stereos and televisions that are built in
to the spa as factory options from Cal Spas™.
Warning – Risk of Injury
The spa water should never exceed 40˚C. Water temperatures between 38˚C and 40˚C are considered
safe for a healthy adult. Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
High water temperatures have a high potential for causing fetal damage during pregnancy. Women
who are pregnant, or who think they are pregnant, should always check with their physician prior to
spa usage.
The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness, with
the possibility of drowning.
Persons suffering from obesity, a medical history of heart disease, low or high blood pressure,
circulatory system problems or diabetes should consult a physician before using the spa.
Read This First!
Page 2 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Persons using medications should consult a physician before using the spa since some medications
may induce drowsiness while others may affect heart rate, blood pressure and circulation.
Hyperthermia Danger
Prolonged exposure to hot air or water can induce hyperthermia. Hyperthermia occurs when the internal
temperature of the body reaches a level 2˚C to 4˚C above the normal body temperature of 37˚C. While
hyperthermia has many health benefits, it is important not to allow your body’s core temperature to rise
above 39.5˚C. Symptoms of excessive hyperthermia include dizziness, lethargy, drowsiness and fainting.
The effects of excessive hyperthermia may include:
Failure to perceive heat
Failure to recognize the need to exit spa or hot tub
Unawareness of impending hazard
Fetal damage in pregnant women
Physical inability to exit the spa
Unconsciousness
WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.
Basic Spa Information
The following operating and maintenance instructions are very important and must be followed carefully.
With the proper care and maintenance, your Cal Spa will provide you with years of satisfaction and
performance.
Do not be afraid to push buttons or turn knobs to learn about your new Cal Spa, as it is built with quality
materials and excellent craftsmanship.
Your new Cal Spa has been engineered with a high-powered water pump that pushes water through
various therapy jets, which will relax even the tightest muscles. In addition to the water pressure, you can
add air into the spa water with air venturi handles located seat-side that increase the intensity of your
massage.
The filtering of this spa is very important. It will minimize cleaning time and the amount of chemicals
needed to keep your spa water balanced. The two daily pre-programmed filter cycles of two hours in
duration can be increased to six hour cycles if the need arises. This can be accomplished through the
topside control panel.
IMPORTANT: Keep the spa covered when not in use!
Covered spas use less electricity while maintaining a set temperature.
Covering your spa will protect your spa’s finish from the sun’s ultraviolet rays.
You are required to keep the spa covered to maintain warranty coverage.
Covering your spa helps prevent children from drowning in the spa.
Your new Cal Spa comes equipped with an electric heater. Following the directions listed below will
ensure the most efficient operation:
NOTE: This method is only for spa usage under two hours a week.
Read This First!
2006 Portable Spa Owner's Manual Page 3
LTR20061001, Rev. C
Keep the spa’s operating temperature 3˚C below the desired usage temperature when not in use. One
or two hours before use, set the temperature to the desired temperature.
If the spa usage exceeds two hours a week, the set temperature should remain at the desired usage
temperature.
The air venturis should be used sparingly. When open, water temperature drops quite rapidly and can
also dissipate chemicals.
Allowing the water temperature to lower more than 6˚C below the desired usage temperature and
reheating it prior to usage will cause the heater to operate longer than it normally would maintaining the
desired temperature. Doing this will increase your operating cost and makes your heater work more than
necessary.
The filter needs to be cleaned or changed on a regular basis. This process takes only a few minutes and
the result is increased water clarity and equipment longevity.
Water level is very important to the operation of your spa. If the water level is too low or too high, your
spa will not operate properly. The water level should be to the middle of the skimmer area when the spa is
not being used.
We recommend that your spa water be changed every 4 to 6 months. You may find the need to change
your spa water more frequently with heavy use. When empty, your spa should be cleaned with a non-
abrasive cleaner, such as Cal Spas™ All Surface Cleaner, and then rinsed thoroughly.
See the section “Cleaning and Maintaining Your Spa” for instructions on draining your spa.
When filling your spa, always fill through the skimmer filter canister. Use only regular tap water.
WARNING: DO NOT USE SOFT WATER.
Preparing for Your New Portable Spa
Page 4 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Preparing for Your New Portable Spa
Congratulations! You have purchased a Cal Spa™. With a little preparation and care, your spa will give
you many years of enjoyment. This section has been designed to ensure that your new spa is installed
safely and is ready to enjoy as quickly as possible.
Most cities and counties require permits for exterior construction and electrical circuits. In addition, some
communities have codes requiring residential barriers such as fencing and/or self-closing gates on
property to prevent unsupervised access to the property by children. Your dealer can provide information
on which permits may be required and how to obtain them prior to the delivery of your Cal Spa™.
Planning the Best Location For Your Spa
Here are some of the things that you will need to consider when determining where to place your new spa.
Safety First
Do not place your spa within 3 meters of overhead power lines.
Make sure the spa is positioned so that access to the equipment compartment and all side panels will
not be blocked. Be certain that your installation will meet all city and local safety codes and
requirements.
Consider How You Will Use Your Spa
How you intend to use your spa will help you determine where you should position it. For example, will
you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation,
be sure to leave plenty of room around it for activity. If you will use it for relaxation and therapy, you’ll
probably want to create a specific mood around it.
Plan for Your Environment
If you live in a region where it snows in the winter or rains frequently, place the spa near a house entry.
By doing this, you will have a place to change clothes and not be uncomfortable.
Consider Your Privacy
In a cold-weather climate, bare trees won’t provide much privacy. Think of your spa’s surroundings
during all seasons to determine your best privacy options. Consider the view of your neighbors as well
when you plan the location of your spa.
Provide A View With Your Spa
Think about the direction you will be facing when sitting in your spa. Do you have a special landscaped
area in your yard that you find enjoyable? Perhaps there is an area that catches a soothing breeze during
the day or a lovely sunset in the evening.
Preparing for Your New Portable Spa
2006 Portable Spa Owner's Manual Page 5
LTR20061001, Rev. C
Keep Your Spa Clean
Prevent dirt and contaminants from being tracked into your spa by placing a foot mat at the spa’s entrance
where the bather’s can clean their feet before entering your spa. You may also consider keeping a small
water-filled basin nearby for bathers to rinse their feet before enter your spa.
In planning your spa’s location, consider a location where the path to and from the house can be kept
clean and free of debris.
Allow For Service Access
Many people choose to install a decorative structure around their spa. If you are installing your spa with
any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always
best to design special installations so that the spa can still be moved, or lifted off the ground.
Preparing a Good Foundation for Your Portable Spa
Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of
the spa and the occupants who use it. If the foundation is inadequate, it may shift or settle after the spa is
in place, causing stress that could damage your spa shell or finish.
Damage caused by inadequate or improper foundation support is not covered by the warranty. It is
the responsibility of the spa owner to provide a proper foundation for the spa. We strongly
recommended that you have a qualified, licensed contractor prepare the foundation for your spa.
Place the spa on a level foundation (preferably a 10 cm concrete slab). If you are installing the spa
indoors, pay close attention to the flooring beneath it. Choose flooring that will not be damaged or
stained.
If you are installing your spa on an elevated wood deck or other structure, consult a structural engineer or
a contractor to ensure the structure will support the weight of 68 kg per square foot.
Your Cal Spas™ retailer can help you with your foundation and more. Your retailer has a wealth of
information and experience about how to get the most out of your spa and can provide you with a full line
of accessories that are designed to compliment your spa and increase your enjoyment.
Preparing for Your New Portable Spa
Page 6 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Electrical Set-up Before Delivery of Your Spa
When installed internationally, the electrical wiring of the spa must meet the requirements of any
applicable national, state or local codes. The electrical circuit must be installed by an electrical contractor
and approved by a local building / electrical inspector.
All 230V spas must be permanently connected (hard wired) to the power supply. Supplying power to a
spa that is not in accordance with these instructions will void both the independent testing agency listing
and the manufacturer’s warranty.
The power supplied to the spa must be on a dedicated RCD protected circuit with no other appliances or
lights sharing the power.
To determine the current, voltage, and wire size required for the spa configuration to be connected, refer
to the following:
Wire size must comply with applicable local, state, and national codes.
Wire size is determined by length of run from breaker box to spa and maximum current draw.
We recommend copper wire with THHN insulation or equivalent.
All wiring must be copper to ensure adequate connections. Do not use aluminum wire.
When code requires the use of wires larger than #6 (10mm²), install a junction box near the spa and
use #6 (10mm²) wire between the junction box and the spa.
IMPORTANT: A clearly labeled emergency shutoff or control switch for the purpose of disconnecting
all electrical power to the spa including the motors, recirculation system and jet system(s) shall be
installed at a point readily accessible to the users and not less than 1.5 meters away, adjacent to, and
within sight of the spa or as applicable per national code.
Preparing for Your New Portable Spa
2006 Portable Spa Owner's Manual Page 7
LTR20061001, Rev. C
230 Volt Electrical Installation
All 230V spas are required to have a residual current device (RCD)
breaker and should only be wired by a licensed electrician. To ensure
proper wiring of your RCD, follow the wiring diagram on the next page.
Always follow applicable local, state, and federal codes and guidelines.
Your new 230V Cal Spa™ requires a dedicated 20-Amp RCD Service
with three #10 AWG copper wires. This will include a BROWN load
wire for your incoming power, a BLUE wire for your neutral, and a
GREEN/YELLOW wire for your ground.
#10 AWG wire is acceptable on wire run up to 20 meters. Wire run
over 20 meters must increase to #8 AWG gauge.
Please note that this is the only acceptable electrical wiring procedure.
Spas wired in any other way will void your warranty and may result in
serious injury.
Before each use of your spa, you should check the RCD. During this test, the spa should be operational.
1. Press the test button on the RCD. The RCD will trip and the spa will shut off.
2. Wait 30 seconds and reset the RCD breaker. This is accomplished by turning the breaker off then
back on. Your spa will be operational in about five seconds.
3. Your spa is now safe to use.
Figure 1. Two-Phase Incoming Power
Preparing for Your New Portable Spa
Page 8 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Figure 2. RCD Hook-Up
Preparing for Your New Portable Spa
2006 Portable Spa Owner's Manual Page 9
LTR20061001, Rev. C
Filling and Powering Up Your Portable Spa
Never fill your spa with soft water. Soft water makes it impossible to maintain the proper water chemistry
and may cause the water to foam, which will ultimately harm the finish of the spa and void your warranty.
1. Once the spa has been placed on an approved surface and has been correctly wired by a licensed
electrician, inspect all plumbing connections in the equipment area of your spa. Ensure that these
connections are secure and that they did not loosen during shipment.
2. If equipped, open all gate valves in the equipment area. Before operating the spa, these valves must
be in the UP or OPEN position.
3. Remove the filter basket and cartridge from skimmer/filter canister.
4. Place a garden hose in the skimmer/filter canister and fill your spa with regular tap water to the
proper water level (halfway up the skimmer area).
5. (For owners of the automatic bromine generator) Make sure the dial on the face of the bromine
generator unit is turned to the OFF position.
6. Open the air relief valve (located next to the two filters, if equipped) after the air bubbles stop
coming out of it. Close the valve hand-tight.
7. Once the water is at the correct level and air is bled, turn on the power at the GFCI breaker. (Ensure
that the 120V spas are connected to the proper electrical outlet.)
NOTE: When the power is turned on to the spa, it will perform a diagnostic check for 30 seconds. When
the diagnostic is complete, the spa will automatically operate at filter speed and continue heating
until the spa water temperature reaches the default temperature of 37.7˚C.
8. If no water is flowing when the pump is running there could be an air pocket at the suction side of
the pump. Shut off power to the spa and loosen the pump union on the suction side of the pump to
bleed the air. When air is bled, turn power back on.
9. Re-install the filter and the filter basket into the skimmer/filter canister.
The spa is now ready for use.
NOTE: Never run the spa with the gate valves closed or without water circulating for long periods
of time. Be careful not to over-tighten the plumbing fittings.
Operating Your Spa
Page 10 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Operating Your Spa
5005 Electronic Control Operation
Figure 3. 5005 Electronic Control
Initial Start up
When first powered up, the 5005 system (Figure 3) performs a self-diagnostic check, then automatically
heats to and maintains 37.5C until you change the set temperature as described in the “Temperature
Adjustment” section below.
Temperature Adjustment (Range 26.6˚C to 40˚C)
The electronic control panel displays the actual water temperature in centigrade.
To display the temperature that the spa is set to:
Press the TEMP button. The set temperature setting will flash.
While the display is flashing, each time you press the TEMP button, the set temperature will increase
or decrease by one degree.
Letting the display revert back to the actual water temperature, then pressing the TEMP button again will
allow you to change the direction of temperature adjustment.
Standard and Economy Modes
Your new spa is equipped with a heating feature that gives you complete control of the heating system.
When the spa is powered up, it will automatically start in the standard heating mode. In this mode, the
heating system will automatically activate whenever the water temperature drops more than one degree
below the set temperature. In the economy heating mode, the heating system will only activate during
filtration times.
Operating Your Spa
2006 Portable Spa Owner's Manual Page 11
LTR20061001, Rev. C
To switch from the standard heating mode to the economy heating mode, simply press the TEMP button
followed by the LIGHT button. Press the same sequence to switch back to the standard heating mode.
Once in the economy heating mode, Ec will display in the center of the control panel and flash alternately
with the water temperature.
NOTE: There is no control panel message displayed while in the standard heating mode; only the actual
water temperature is displayed.
Some spa models are equipped with the exclusive XL Heat Exchanger™, the most efficient spa heater
available anywhere. This highly innovative device heats water faster and more efficiently with no
chemical build-up. For your protection, it includes a High Limit Overheat Protection safety device that
prevents spa equipment from overheating. The XL Heat Exchanger™ works automatically and requires
no maintenance.
Jets
Press the JETS button:
One pump equipment:
Once to activate the low speed pump
Twice to activate the high speed pump
Three times to turn off the high-speed
One pump equipment with circulation pump:
Once to activate the circulation pump
Twice to activate the circulation pump and the high-speed pump
Three times to turn off both the circulation pump and the high-speed pump
Two pump equipment without circulation pump:
Once to activate the low-speed pump
Twice to activate the high speed on pump 1
Three times to activate the high speed on pump 1 and high speed on pump 2
Four times to turn off the high speed on pump 1. The high-speed on pump 2 will remain on.
Five times to turn the high speed off on pump 2.
Two pump equipment with circulation pump:
Once to activate the circulation pump
Twice to activate the circulation pump and the high-speed pump 1
Three times to activate the circulation pump, high-speed pump 1 and high-speed pump 2
Four times to turn off the circulation pump and high speed pump 1. High-speed pump 2 will
remain on.
Five times to turn off the high-speed on pump 2
Operating Your Spa
Page 12 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Light
Press the LIGHT button to turn on the spa light and again to turn the light off.
Turbo (Optional)
Press the OPTION button to turn on the turbo system. Press it once again to turn off the turbo system.
Setting the Temperature Lock
This feature allows you to lock a temperature into the system. When engaged the set temperature will
blink on and off when the TEMP button is pressed. However, you will not be able to change it until you
unlock the set temperature:
Press the TEMP button.
Press the OPTION button to unlock the set temperature.
Select a temperature with the TEMP button.
Press the OPTION button to set and lock the temperature.
Automatic Time Outs
These features will automatically turn themselves off during periods of continuous use:
Low speed pump After 2 hours
Optional circulation pump After 4 hours
High-speed pump After 15 minutes
Optional turbo system After 15 minutes
Spa light After 15 minutes
Setting Filtration Cycles
Your spa will automatically filter itself twice a day. To set the filtration time, turn off the power to the
spa at the GFCI breaker. Turn the GFCI breaker back on at the time of day you would like to start the
filtration cycle. The first cycle will start after the spa is powered up. The second filtration cycle will
begin twelve hours later. The filtration cycle duration is preset to 2 hours (F2). To change the duration of
the filtration time, press the Temp pad, then press the Jets pad. Press the Temp button again to choose
from 2,4,6,8, and 12 hours twice a day (FC = Filtration Continuous).
After selecting the desired filtration cycle duration, press the Jets pad to exit the filtration program. The
circulating pump and ozone generator (optional) will run during filtration cycles.
Operating Your Spa
2006 Portable Spa Owner's Manual Page 13
LTR20061001, Rev. C
NOTE: The filtration cycle settings of F8 and FC are only intended for use with the optional Spa Cal™
Filtration System.
Safety Suction System
Your new Cal Spa™ is equipped with a state-of-the-art Safety Suction System. This will automatically
shutdown the spa in the event of a filtration or suction restriction, and display SF on the topside control
panel. If this happens, check all suction fittings and filter cartridge(s) for obstructions. Then, reset the
system by pressing any control panel button.
Diagnostic Messages
Message Meaning
OH Overheat protection (spa is shutdown) DO NOT ENTER THE WATER! If the spa has
reached 45˚C, remove the spa cover to cool the water. Overheating may occur if the filter
cycle is set too long. At 43˚C, the spa should reset itself. If the high-limit sensor detects
48˚C at the heater, the spa will shut down. When the heater cools down to 43˚C, press any
button to reset the spa. If the spa will not reset, then shut the power off to the spa and call
your dealer of service organization.
FL Flow Detection Switch. Pressure switch is not working correctly. Call your dealer or
service organization.
Sn Sensor (Spa is shut down). The high limit or water temperature sensor is not working
correctly. Call your dealer or service organization.
Sf Vacuum Switch (Spa is shut down). The display will show “SF” as soon as the vacuum
switch closes. All functions will turn off and the system will be disabled until a panel
button is pressed.
LED - Heater LED will come on when the heater is on (and goes off when heater is off).
- Ozone LED will come on when in filtration cycles.
- Safety switch is a status LED noting power and system monitoring.
Operating Your Spa
Page 14 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
8005 Electronic Control Operation
When first powered up, the 8005 electronic system (Figure 4) will perform a self-diagnostic check and
then it will automatically heat to and maintain a temperature of 37.5˚C until you change the set
temperature as listed in the “Temperature Adjustment” section below.
Figure 4. 8005 Electronic Control Panel
These instructions will describe features and options that your particular spa may not be equipped with.
Initial Start-up
When your spa is first powered up, it displays some configuration codes and then goes into priming mode
(Pr will appear on the display panel). This mode lasts up to four minutes and then the spa begins to heat to
its pre -programmed temperature of 37.7˚C. You can exit the priming mode early by pressing UP or
DOWN buttons.
Temperature Adjustment (26.0˚C - 40.0˚C)
The start-up temperature is set at 37.5˚C. The last measured temperature is constantly displayed on the
control panel. Note that the last measured spa temperature is displayed. The displayed temperature will be
updated when the pump has been running for at least two minutes.
Press the UP or DOWN buttons once to display the set temperature. Each time either button is pressed
again, the set temperature will increase or decrease depending on which button is pressed. After three
seconds, the control panel will automatically display the last measured spa temperature.
Note: Some spa models are equipped with the exclusive XL Heat Exchanger™, the most efficient spa
heater available anywhere. This highly innovative device heats water faster and more efficiently with no
chemical build-up. For your protection, it includes a High Limit Overheat Protection safety device that
prevents spa equipment from overheating. The XL Heat Exchanger™ works automatically and requires
no maintenance.
Operating Your Spa
2006 Portable Spa Owner's Manual Page 15
LTR20061001, Rev. C
Time
When time hasn’t been programmed, the TIME icon flashes. To set the time, press the TIME button and
then the MODE/PROG button. Use the UP and DOWN buttons to adjust time. See the next page for
more detailed instructions.
Standard, Economy, Sleep, and Standby Modes
Mode/Prog: This button is used to switch between standard, economy, and sleep modes.
1. Press MODE/PROG to enter mode programming.
2. Press the DOWN button to cycle through to the desired mode.
3. Press MODE/PROG to confirm selection.
Standard Mode: This is programmed to maintain the desired temperature. Note that the last measured
spa temperature displayed is current only when the pump has been running for at least two minutes. The
“STAND” icon will display until the mode is changed.
Economy Mode: Economy mode heats the spa to the set temperature only during filter cycles. The
“ECON” icon will display until the mode is changed. Pressing the JETS 1 button while in economy mode
puts the spa in standard-in-economy mode, which operates the same as standard mode but reverts back to
economy mode automatically after one hour. During this time, pressing the MODE/PROG button will
revert to economy mode immediately.
Sleep Mode: Sleep mode heats the spa to within 11˚C of the set temperature only during filter cycles. The
“SLEEP” icon will display until the mode is changed.
Standby Mode: Pressing “Warm” or “Cool” then “Jets 2” will turn off all spa functions temporarily. This
is helpful when changing a filter. Pressing any button resets the spa.
Jets 1 and Jets 2
Press the JETS 1 button once to turn pump 1 on or off and to shift between low and high speeds if
equipped. If left running, the low speed turns off after two hours and the high speed turns off after 15
minutes. On non-circulation systems, the low speed of pump 1 runs when the blower or any other pump is
on. It may also activate for at least two minutes every 30 minutes to detect the spa temperature and then to
heat to the set temperature if needed, depending upon the mode. When the low speed turns on
automatically, it cannot be deactivated from the panel; however, the high speed may be started.
Option (Optional Blower)
Press the OPTION button to turn the optional equipment on and off. If left on, the equipment will
automatically turn off after 15 minutes.
Light
Press the LIGHT button to turn the spa light on and off.
Invert
Press the INVERT button to change the numbers in the display to read upside down. Another press
returns the display to the right-side-up position. This enables you to read the display while you are in the
spa.
Operating Your Spa
Page 16 2006 Portable Spa Owner's Manual
LTR20061001, Rev. C
Locking the Panel
To lock the panel:
Press TIME, JETS 1, and the UP button within three seconds. When locked, the panel will display
“LOCK”. All buttons are frozen except the TIME button.
To unlock the panel:
Press TIME, JETS ,1 then the DOWN button within three seconds.
Setting the Temperature Lock
To activate the temperature lock:
Press the UP or DOWN button, TIME, JETS 1, then the UP button within three seconds. The
panel will display “TEMP LOCK” when the set temperature is locked.
To unlock the set temperature:
Press the UP or DOWN button, TIME, JETS 1, then the DOWN button..
Circulation Pump (optional)
If your system is equipped with a circulation pump, it may be configured to work in one of two different
ways:
1. The circulation pump operates continuously (24 hours) with the exception of turning off for 30
minutes at a time when the water temperature reaches 1.7˚C above the set temperature (most likely
to happen in very hot climates).
2.
The circulation pump will come on when the system is checking temperature, during filter cycles,
during freeze conditions, or when another pump is on.
Preset Filter Cycles
There are two filter cycles per day. The start and end times of each cycle are programmable. To program,
set the time as instructed above, then press MODE/PROG to advance to the next setting (or to exit after
the last setting). The default filter cycles are as follows:
The first filter cycle is automatically activated at 8:00 AM and operates the pump until 10:00 AM.
The “FILTER 1” indicator icon will light when filter 1 is running.
The second filter cycle is automatically activated at 8:00 PM and operates the pump until 10:00
PM. The “FILTER 2” indicator icon will light when filter 2 is running.
The pump and the ozone generator will run during filtration. At the start of each filter cycle, the blower
will run on highest speed for 30 seconds to clean out the air channels. The lowest speed of pump 2 and
pump 3 will run for five minutes. In the event of power loss or shut down, the time of day will need to be
reset for filter cycles to run according to your desired programming.
Clean-up Cycle
When the pump or blower is turned on by a button press, a clean-up cycle begins 30 minutes after the
pump or blower is turned off or times out. The pump and the ozone generator will run for one hour.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296

Cal Spas Portable Spas Le manuel du propriétaire

Taper
Le manuel du propriétaire