Zanussi ZRB934PW2 Manuel utilisateur

Marque: Zanussi

Modèle: ZRB934PW2

Catégorie: Réfrigérateurs-congélateurs

Taper: Manuel utilisateur

User manual 2

Notice d'utilisation 15

Fridge Freezer

Réfrigérateur/congélateur

ZRB934PW2

Contents

Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5

Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5

First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 7

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8

Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10

Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12

Environmental concerns _ _ _ _ _ _ _ _ _ _ 14

Subject to change without notice.

Safety instructions

In the interest of your safety and to ensure the

correct use, before installing and first using the

appliance, read this user manual carefully, in-

cluding its hints and warnings. To avoid unnec-

essary mistakes and accidents, it is important

to ensure that all people using the appliance

are thoroughly familiar with its operation and

safety features. Save these instructions and

make sure that they remain with the appliance

if it is moved or sold, so that everyone using it

through its life will be properly informed on ap-

pliance use and safety.

For the safety of life and property keep the pre-

cautions of these user's instructions as the

manufacturer is not responsible for damages

caused by omission.

Children and vulnerable people safety

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or instruc-

tion concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure

that they do not play with the appliance.

• Keep all packaging well away from children.

There is risk of suffocation.

• If you are discarding the appliance pull the

plug out of the socket, cut the connection

cable (as close to the appliance as you can)

and remove the door to prevent playing chil-

dren to suffer electric shock or to close

themselves into it.

• If this appliance featuring magnetic door

seals is to replace an older appliance having

a spring lock (latch) on the door or lid, be

sure to make that spring lock unusable be-

fore you discard the old appliance. This will

prevent it from becoming a death trap for a

child.

General safety

Warning!

Keep ventilation openings, in the appliance en-

closure or in the built-in structure, clear of ob-

struction.

• The appliance is intended for keeping food-

stuff and/or beverages in a normal house-

hold and similar applications such as:

– staff kitchen areas in shops, offices and

other working environments;

– farm houses and by clients in hotels, mo-

tels and other residential type environ-

ments;

– bed and breakfast type environments;

– catering and similar non-retail applica-

tions.

• Do not use a mechanical device or any artifi-

cial means to speed up the thawing process.

• Do not use other electrical appliances (such

as ice cream makers) inside of refrigerating

appliances, unless they are approved for this

purpose by the manufacturer.

• Do not damage the refrigerant circuit.

• The refrigerant isobutane (R600a) is con-

tained within the refrigerant circuit of the ap-

pliance, a natural gas with a high level of en-

vironmental compatibility, which is neverthe-

less flammable.

www.zanussi.com

During transportation and installation of the

appliance, be certain that none of the com-

ponents of the refrigerant circuit become

damaged.

If the refrigerant circuit should become dam-

aged:

– avoid open flames and sources of ignition

– thoroughly ventilate the room in which the

appliance is situated

• It is dangerous to alter the specifications or

modify this product in any way. Any damage

to the cord may cause a short-circuit, fire

and/or electric shock.

Warning! Any electrical component

(power cord, plug, compressor) must be

replaced by a certified service agent or quali-

fied service personnel to avoid hazard.

1. Power cord must not be lengthened.

2. Make sure that the power plug is not

squashed or damaged by the back of

the appliance. A squashed or damaged

power plug may overheat and cause a

fire.

3. Make sure that you can come to the

mains plug of the appliance.

4. Do not pull the mains cable.

5. If the power plug socket is loose, do not

insert the power plug. There is a risk of

electric shock or fire.

6. You must not operate the appliance

without the lamp cover (if foreseen) of

interior lighting.

• This appliance is heavy. Care should be tak-

en when moving it.

• Do not remove nor touch items from the

freezer compartment if your hands are

damp/wet, as this could cause skin abra-

sions or frost/freezer burns.

• Avoid prolonged exposure of the appliance

to direct sunlight.

• Bulb lamps (if foreseen) used in this appli-

ance are special purpose lamps selected for

household appliances use only. They are not

suitable for household room illumination.

Daily Use

• Do not put hot pot on the plastic parts in the

appliance.

• Do not store flammable gas and liquid in the

appliance, because they may explode.

• Do not place food products directly against

the air outlet on the rear wall. (If the appli-

ance is Frost Free)

• Frozen food must not be re-frozen once it

has been thawed out.

• Store pre-packed frozen food in accordance

with the frozen food manufacturer's instruc-

tions.

• Appliance's manufacturers storage recom-

mendations should be strictly adhered to.

Refer to relevant instructions.

• Do not place carbonated or fizzy drinks in

the freezer compartment as it creates pres-

sure on the container, which may cause it to

explode, resulting in damage to the appli-

ance.

• Ice lollies can cause frost burns if consumed

straight from the appliance.

Care and cleaning

• Before maintenance, switch off the appli-

ance and disconnect the mains plug from

the mains socket.

• Do not clean the appliance with metal ob-

jects.

• Do not use sharp objects to remove frost

from the appliance. Use a plastic scraper.

• Regularly examine the drain in the refrigera-

tor for defrosted water. If necessary, clean

the drain. If the drain is blocked, water will

collect in the bottom of the appliance.

Installation

Important! For electrical connection carefully

follow the instructions given in specific

paragraphs.

• Unpack the appliance and check if there are

damages on it. Do not connect the appli-

ance if it is damaged. Report possible dam-

ages immediately to the place you bought it.

In that case retain packing.

www.zanussi.com

• It is advisable to wait at least four hours be-

fore connecting the appliance to allow the oil

to flow back in the compressor.

• Adequate air circulation should be around

the appliance, lacking this leads to overheat-

ing. To achieve sufficient ventilation follow

the instructions relevant to installation.

• Wherever possible the back of the product

should be against a wall to avoid touching or

catching warm parts (compressor, condens-

er) to prevent possible burn.

• The appliance must not be located close to

radiators or cookers.

• Make sure that the mains plug is accessible

after the installation of the appliance.

• Connect to potable water supply only (If a

water connection is foreseen).

Service

• Any electrical work required to do the servic-

ing of the appliance should be carried out by

a qualified electrician or competent person.

• This product must be serviced by an author-

ized Service Centre, and only genuine spare

parts must be used.

Environment Protection

This appliance does not contain gasses

which could damage the ozone layer, in

either its refrigerant circuit or insulation materi-

als. The appliance shall not be discarded to-

gether with the urban refuse and rubbish. The

insulation foam contains flammable gases: the

appliance shall be disposed according to the

applicable regulations to obtain from your local

authorities. Avoid damaging the cooling unit,

especially at the rear near the heat exchanger.

The materials used on this appliance marked

by the symbol

are recyclable.

www.zanussi.com

Product description

2 43 7 8 109

111314

5 61

Vegetable drawers

Glass shelf

Control panel

Dairy shelf

Door shelf

Bottle shelf

Freezer basket

Maxibox basket

Freezer basket

Rating plate

Operation

Switching on

Insert the plug into the wall socket.

Turn the Temperature regulator clockwise to a

medium setting.

Switching off

To turn off the appliance, turn the Temperature

regulator to the "O" position.

Temperature regulation

The temperature is automatically regulated.

To operate the appliance, proceed as follows:

• turn the Temperature regulator toward lower

settings to obtain the minimum coldness.

• turn the Temperature regulator toward high-

er settings to obtain the maximum coldness.

www.zanussi.com

A medium setting is generally the most

suitable.

However, the exact setting should be chosen

keeping in mind that the temperature inside the

appliance depends on:

• room temperature

• how often the door is opened

• the quantity of food stored

• the location of the appliance.

Important! If the ambient temperature is high

or the appliance is fully loaded, and the

appliance is set to the lowest temperatures, it

may run continuously causing frost to form on

the rear wall. In this case the dial must be set

to a higher temperature to allow automatic

defrosting and therefore reduced energy

consumption.

First use

Cleaning the interior

Before using the appliance for the first time,

wash the interior and all internal accessories

with lukewarm water and some neutral soap so

as to remove the typical smell of a brand-new

product, then dry thoroughly.

Important! Do not use detergents or abrasive

powders, as these will damage the finish.

Daily use

Freezing fresh food

The freezer compartment is suitable for freez-

ing fresh food and storing frozen and deep-fro-

zen food for a long time.

To freeze fresh foods it is not necessary to

change the medium setting.

However, for a faster freezing operation, turn

the temperature regulator toward higher set-

tings to obtain the maximum coldness.

Important! In this condition, the refrigerator

compartment temperature might drop below

0°C. If this occurs reset the temperature

regulator to a warmer setting.

Place the fresh food to be frozen on the bottom

compartment.

Storage of frozen food

When first starting-up or after a period out of

use, before putting the products in the com-

partment let the appliance run at least 2 hours.

The freezer drawers ensure that it is quick and

easy to find the food package you want. If large

quantities of food are to be stored, remove all

drawers except for the bottom drawer which

needs to be in place to provide good air circu-

lation. On all shelves it is possible to place

food that protrude until 15 mm from the door.

Important! In the event of accidental

defrosting, for example due to a power failure,

if the power has been off for longer that the

value shown in the technical characteristics

chart under "rising time", the defrosted food

must be consumed quickly or cooked

immediately and then re-frozen (after cooling).

Thawing

Deep-frozen or frozen food, prior to being

used, can be thawed in the refrigerator com-

partment or at room temperature, depending

on the time available for this operation.

Small pieces may even be cooked still frozen,

directly from the freezer: in this case, cooking

will take longer.

Movable shelves

The walls of the refrigerator are equipped with

a series of runners so that the shelves can be

positioned as desired.

www.zanussi.com

Positioning the door shelves

To store various size food packages, the door

shelves can be placed at different heights.

Gradually pull the shelf in the direction of the

arrows until it comes free, then reposition as

required.

Removal of freezing baskets from the

freezer

The freezing baskets have a limit stop to pre-

vent their accidental removal or falling out. At

the time of its removal from the freezer, pull the

basket towards yourself and, upon reaching

the end point, remove the basket by tilting its

front upwards.

At the time of putting it back, slightly lift the

front of the basket to insert it into the freezer.

Once you are over the end points, push the

baskets back in their position.

Helpful hints and tips

Normal Operating Sounds

• You may hear a faint gurgling and a bubbling

sound when the refrigerant is pumped

through the coils or tubing. This is correct.

• When the compressor is on, the refrigerant

is being pumped around and you will hear a

whirring sound and a pulsating noise from

the compressor. This is correct.

• The thermic dilatation might cause a sudden

cracking noise. It is natural, not dangerous

physical phenomenon. This is correct.

• When the compressor switches on or

switches off, you will hear a faint "click" of

the temperature regulator. This is correct.

Hints for energy saving

• Do not open the door frequently or leave it

open longer than absolutely necessary.

• If the ambient temperature is high and the

Temperature Regulator is set to low temper-

ature and the appliance is fully loaded, the

compressor may run continuously, causing

frost or ice on the evaporator. If this hap-

pens, set the Temperature Regulator toward

warmer settings to allow automatic defrost-

ing and so a saving in electricity consump-

tion.

Hints for fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating liq-

uids in the refrigerator

• do cover or wrap the food, particularly if it

has a strong flavour

• position food so that air can circulate freely

around it

Hints for refrigeration

Useful hints:

Meat (all types) : wrap in polythene bags and

place on the glass shelf above the vegetable

drawer.

For safety, store in this way only one or two

days at the most.

Cooked foods, cold dishes, etc.: these should

be covered and may be placed on any shelf.

Fruits and vegetables: these should be thor-

oughly cleaned and placed in the special draw-

er(s) provided. When in contact, lemon juice

can discolor the plastic parts of your fridge. It

is therefore recommended to keep citruses in

separate containers.

www.zanussi.com

Butter and cheese: these should be placed in

special airtight containers or wrapped in alumi-

nium foil or polythene bags to exclude as much

air as possible.

Bottles: these should have a cap and should

be stored in the bottle rack on the door.

Bananas, potatoes, onions and garlic, if not

packed, must not be kept in the refrigerator.

Hints for freezing

To help you make the most of the freezing

process, here are some important hints:

• the maximum quantity of food which can be

frozen in 24 hrs. is shown on the rating

plate;

• the freezing process takes 24 hours. No fur-

ther food to be frozen should be added dur-

ing this period;

• only freeze top quality, fresh and thoroughly

cleaned, foodstuffs;

• prepare food in small portions to enable it to

be rapidly and completely frozen and to

make it possible subsequently to thaw only

the quantity required;

• wrap up the food in aluminium foil or poly-

thene and make sure that the packages are

airtight;

• do not allow fresh, unfrozen food to touch

food which is already frozen, thus avoiding a

rise in temperature of the latter;

• lean foods store better and longer than fatty

ones; salt reduces the storage life of food;

• water ices, if consumed immediately after re-

moval from the freezer compartment, can

possibly cause the skin to be freeze burnt;

• it is advisable to show the freezing in date on

each individual pack to enable you to keep

tab of the storage time.

Hints for storage of frozen food

The freezer baskets ensure that it is quick and

easy to find the food package you want. If large

quantities of food are to be stored, remove all

drawers except for the bottom basket which

needs to be in place to provide good air circu-

lation.

To obtain the best performance from this appli-

ance, you should:

• make sure that the commercially frozen food-

stuffs were adequately stored by the retailer;

• be sure that frozen foodstuffs are transferred

from the foodstore to the freezer in the

shortest possible time;

• not open the door frequently or leave it open

longer than absolutely necessary;

• once defrosted, food deteriorates rapidly

and cannot be refrozen;

• do not exceed the storage period indicated

by the food manufacturer.

Care and cleaning

Caution! Unplug the appliance before

carrying out any maintenance operation.

This appliance contains hydrocarbons in

its cooling unit; maintenance and recharg-

ing must therefore only be carried out by au-

thorized technicians.

Periodic cleaning

The equipment has to be cleaned regularly:

• clean the inside and accessories with luke-

warm water and some neutral soap.

• regularly check the door seals and wipe

clean to ensure they are clean and free from

debris.

• rinse and dry thoroughly.

Important! Do not pull, move or damage any

pipes and/or cables inside the cabinet.

Never use detergents, abrasive powders,

highly perfumed cleaning products or wax

polishes to clean the interior as this will

damage the surface and leave a strong odour.

Clean the condenser (black grill) and the com-

pressor at the back of the appliance with a

brush. This operation will improve the perform-

ance of the appliance and save electricity con-

sumption.

Important! Take care of not to damage the

cooling system.

www.zanussi.com

Many proprietary kitchen surface cleaners con-

tain chemicals that can attack/damage the

plastics used in this appliance. For this reason

it is recommended that the outer casing of this

appliance is only cleaned with warm water with

a little washing-up liquid added.

After cleaning, reconnect the equipment to the

mains supply.

Defrosting of the refrigerator

Frost is automatically eliminated from the evap-

orator of the refrigerator compartment every

time the motor compressor stops, during nor-

mal use. The defrost water drains out through a

trough into a special container at the back of

the appliance, over the motor compressor,

where it evaporates.

It is important to periodically clean the defrost

water drain hole in the middle of the refrigera-

tor compartment channel to prevent the water

overflowing and dripping onto the food inside.

Use the special cleaner provided, which you

will find already inserted into the drain hole.

Defrosting the freezer

A certain amount of frost will always form on

the freezer shelves and around the top com-

partment.

Defrost the freezer when the frost layer rea-

ches a thickness of about 3-5 mm.

To remove the frost, follow the instructions be-

low:

• pull out the plug from the wall socket or

switch off the appliance

• remove any stored food, wrap it in several

layers of newspaper and put it in a cool

place

• remove the freezer drawers

• put insulating material around the drawers,

e.g. blankets or newspapers.

Defrosting can be accelerated by placing

bowls with hot water (not boiling) inside the

freezer.

• Loosen the drainage channel from its resting

position, push it in according to the illustra-

tion and place it in the bottom freezer drawer

where water can collect

• carefully scrape off the ice when it starts to

thaw. Use a wood or a plastic scraper

• when all the ice has melted, clean and wipe

the cabinet dry, then put the drainage chan-

nel back in place.

• switch on the cabinet and replace the frozen

foodstuff.

It is recommended to operate the appli-

ance at the highest position of the ther-

mostatic control for some hours so that it

can reach the sufficient storing tempera-

ture as soon as possible.

Important! Never use sharp metal tools to

scrape off frost from the evaporator as you

could damage it. Do not use a mechanical

device or any artificial means to speed up the

thawing process other than those

recommended by the manufacturer. A

temperature rise of the frozen food packs,

during defrosting, may shorten their safe

storage life.

www.zanussi.com

Troubleshooting

Caution! Before troubleshooting,

disconnect the power supply.

Only a qualified electrician or competent

person must do the troubleshooting that is not

in this manual.

Important! There are some sounds during

normal use (compressor, refrigerant

circulation).

Problem Possible cause Solution

The appliance is noisy. The appliance is not supported

properly.

Check if the appliance stands stable

(all the four feet should be on the

floor).

The compressor operates

continually.

The Temperature regulator may be

set incorrectly.

Set a warmer temperature.

The door is not closed correctly. Refer to "Closing the door".

The door has been opened too fre-

quently.

Do not keep the door open longer

than necessary.

The product temperature is too

high.

Let the product temperature de-

crease to room temperature before

storage.

The room temperature is too high. Decrease the room temperature.

Water flows on the rear

plate of the refrigerator.

During the automatic defrosting

process, frost defrosts on the rear

plate.

This is correct.

Water flows into the re-

frigerator.

The water outlet is clogged. Clean the water outlet.

Products prevent that water flows

into the water collector.

Make sure that products do not

touch the rear plate.

Water flows on the

ground.

The melting water outlet does not

flow in the evaporative tray above

the compressor.

Attach the melting water outlet to

the evaporative tray.

There is too much frost

and ice.

Products are not wrapped properly. Wrap the products better.

The door is not closed correctly. Refer to "Closing the door".

The Temperature regulator may be

set incorrectly.

Set a higher temperature.

The temperature in the ap-

pliance is too low.

The Temperature regulator may be

set incorrectly.

Set a higher temperature.

The temperature in the ap-

pliance is too high.

The Temperature regulator may be

set incorrectly.

Set a lower temperature.

The door is not closed correctly. Refer to "Closing the door".

The product temperature is too

high.

Let the product temperature de-

crease to room temperature before

storage.

www.zanussi.com

Problem Possible cause Solution

Many products are stored at the

same time.

Store less products at the same

time.

The temperature in the re-

frigeration is too high.

There is no cold air circulation in

the appliance.

Make sure that there is cold air cir-

culation in the appliance.

The temperature in the

freezer is too high.

Products are too near to each oth-

er.

Store products so that there is cold

air circulation.

The appliance does not

operate.

The appliance is switched off. Switch on the appliance.

The mains plug is not connected to

the mains socket correctly.

Connect the mains plug to the mains

socket correctly.

The appliance has no power. There

is no voltage in the mains socket.

Connect a different electrical appli-

ance to the mains socket. Contact a

qualified electrician.

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

If your appliance is still not working properly af-

ter making the above checks, contact the After

Sales Centre.

Replacing the lamp

1. Disconnect the appliance.

2. Push the movable part to unhook the lamp

cover (1).

3. Remove the lamp cover (2).

4. If needed replace the lamp with a light of

similar characteristic and power. It is sug-

gested to use Osram PARATHOM SPE-

CIAL T26 0.8 Watts.

5. Install the lamp cover.

6. Connect the appliance.

7. Open the door. Make sure that the lamp

comes on.

Closing the door

1. Clean the door gaskets.

2. If necessary, adjust the door. Refer to "In-

stallation".

3. If necessary, replace the defective door

gaskets. Contact the Service Center.

www.zanussi.com

Technical data

Dimension

Height 1750 mm

Width 595 mm

Depth 658 mm

Rising Time 20 h

Voltage 230-240 V

Frequency 50 Hz

The technical information are situated in the

rating plate on the internal left side of the appli-

ance and in the energy label.

Installation

Caution! Read the "Safety Information"

carefully for your safety and correct

operation of the appliance before installing the

appliance.

Positioning

Install this appliance at a location where the

ambient temperature corresponds to the cli-

mate class indicated on the rating plate of the

appliance:

Climate

class

Ambient temperature

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

Location

The appliance should be installed well away

from sources of heat such as radiators, boilers,

direct sunlight etc. Ensure that air can circulate

freely around the back of the cabinet. To en-

sure best performance, if the appliance is posi-

tioned below an overhanging wall unit, the min-

imum distance between the top of the cabinet

and the wall unit must be at least 100 mm .

Ideally, however, the appliance should not be

positioned below overhanging wall units. Accu-

rate levelling is ensured by one or more adjust-

able feet at the base of the cabinet.

Warning! It must be possible to

disconnect the appliance from the mains

power supply; the plug must therefore be

easily accessible after installation.

100 mm

min

20 mm

Rear spacers

You can find the two spacers in the bag with

documentation.

Do these steps to install the spacers:

1. Release the screw.

www.zanussi.com

2. Engage the spacer below the screw.

3. Turn the spacer to the right position.

4. Tighten again the screws.

Levelling

When placing the appliance ensure that it

stands level. This can be achieved by two ad-

justable feet at the bottom in front.

Electrical connection

Before plugging in, ensure that the voltage and

frequency shown on the rating plate corre-

spond to your domestic power supply.

The appliance must be earthed. The power

supply cable plug is provided with a contact for

this purpose. If the domestic power supply

socket is not earthed, connect the appliance to

a separate earth in compliance with current

regulations, consulting a qualified electrician.

The manufacturer declines all responsibility if

the above safety precautions are not observed.

This appliance complies with the E.E.C. Direc-

tives.

Door reversibility

Warning! Before carrying out any

operations, remove the plug from the

power socket.

Important! To carry out the following

operations, we suggest that another person

will keep a firm hold on the appliance doors

during the door reversing procedure.

Middle Hinge

• Open the doors. Unscrew the middle hinge

(B). Remove the plastic spacer (A).

• Remove the doors.

• Remove the middle hinge cover pins (C,D)

and move them to the opposite side.

Bottom Hinge

• Unscrew the bottom hinge (A)

• Remove the left-hand cover pins (D) and

move them to the opposite side.

• Re-screw the bottom hinge (A) on the oppo-

site side.

• Unscrew the bottom hinge pivot (B) and

spacer (C), and place them on the opposite

side.

Doors

• Remove the plugs (A) on the top side of

both doors and move them to the opposite

side.

www.zanussi.com

Top Hinge

• Unscrew the top hinge pivot (1) and place it

on the opposite side (2).

• Insert the middle hinge into the bottom door.

• Re-insert the bottom door into bottom hinge,

and then top door into top hinge pivot (1)

while slightly tilting both doors.

• Re-screw the middle hinge (B), securing

both doors to the appliance. Do not forget

the plastic spacer (A).

Do a final check to make sure that:

• All screws are tightened.

• The edges of the doors run parallel to the

side edge of the appliance.

• The magnetic seal adheres to the cabinet.

• The door opens and closes correctly.

If the ambient temperature is cold (i.e. in Win-

ter), the gasket may not fit perfectly to the cabi-

net. In that case, wait for the natural fitting of

the gasket.

In case you do not want to carry out the above

mentioned operations, contact the nearest Af-

ter Sales Service Force. The After Sales Serv-

ice specialist will reverse the doors at your

cost.

Environmental concerns

Recycle the materials with the symbol . Put

the packaging in applicable containers to

recycle it.

Help protect the environment and human

health and to recycle waste of electrical and

electronic appliances. Do not dispose

appliances marked with the symbol

with the

household waste. Return the product to your

local recycling facility or contact your municipal

office.

www.zanussi.com

Sommaire

Instructions de sécurité _ _ _ _ _ _ _ _ _ _ 15

Description de l'appareil _ _ _ _ _ _ _ _ _ _ 18

Fonctionnement _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18

Première utilisation _ _ _ _ _ _ _ _ _ _ _ _ _ 19

Utilisation quotidienne _ _ _ _ _ _ _ _ _ _ _ 19

Conseils utiles _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20

Entretien et nettoyage _ _ _ _ _ _ _ _ _ _ _ 22

En cas d'anomalie de fonctionnement _ _ _ 23

Caractéristiques techniques _ _ _ _ _ _ _ _ 25

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 26

En matière de sauvegarde de l'environnement

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 28

Sous réserve de modifications.

Instructions de sécurité

Pour votre sécurité et garantir une utilisation

correcte de l'appareil, lisez attentivement cette

notice, y compris les conseils et avertisse-

ments, avant d'installer et d'utiliser l'appareil

pour la première fois. Pour éviter toute erreur

ou accident, veillez à ce que toute personne

qui utilise l'appareil connaisse bien son fonc-

tionnement et ses fonctions de sécurité. Con-

servez cette notice avec l'appareil. Si l'appareil

doit être vendu ou cédé à une autre personne,

veillez à remettre cette notice au nouveau pro-

priétaire, afin qu'il puisse se familiariser avec

son fonctionnement et sa sécurité.

Pour la sécurité des personnes et des biens,

conservez et respectez les consignes de sécu-

rité figurant dans cette notice. Le fabricant dé-

cline toute responsabilité en cas de dommages

dus au non-respect de ces instructions.

Sécurité des enfants et des personnes

vulnérables

• Cet appareil n'est pas destiné à être utilisé

par des enfants ou des personnes dont les

capacités physiques, sensorielles ou menta-

les, ou le manque d'expérience et de con-

naissance les empêchent d'utiliser l'appareil

sans risque lorsqu'ils sont sans surveillance

ou en l'absence d'instruction d'une personne

responsable qui puisse leur assurer une utili-

sation de l'appareil sans danger.

Empêchez les enfants de jouer avec l'appa-

reil.

• Ne laissez pas les différents emballages à

portée des enfants. Ils pourraient s'asphyxier.

• Si l'appareil doit être mis au rebut, sortez la

fiche de la prise électrique, coupez le cor-

don d'alimentation au ras de l'appareil et dé-

montez la porte pour éviter les risques

d'électrocution et que des enfants ne restent

enfermés à l'intérieur.

• Cet appareil est muni de fermetures magné-

tiques. S'il remplace un appareil équipé

d'une fermeture à ressort, nous vous con-

seillons de rendre celle-ci inutilisable avant

de vous en débarrasser. Ceci afin d'éviter

aux enfants de s'enfermer dans l'appareil et

de mettre ainsi leur vie en danger.

Consignes générales de sécurité

Avertissement

Veillez à ce que les orifices de ventilation, situ-

és dans l'enceinte de l'appareil ou la structure

intégrée, ne soient pas obstrués.

• Les appareils sont destinés uniquement à la

conservation des aliments et/ou des bois-

sons dans le cadre d’un usage domestique

normal, tel que celui décrit dans la présente

notice.

– dans des cuisines réservées aux employés

dans des magasins, bureaux et autres

lieux de travail ;

– dans les fermes et par les clients dans

des hôtels, motels et autres lieux de sé-

jour ;

– dans des hébergements de type chambre

d'hôte ;

– pour la restauration et autres utilisations

non commerciales.

• N'utilisez pas d'appareils électriques,

d'agents chimiques ou tout autre système

artificiel pour accélérer le processus de dé-

givrage.

www.zanussi.com

• Ne faites pas fonctionner d'appareils électri-

ques (comme des sorbetières électri-

ques, ...) à l'intérieur des appareils de réfri-

gération à moins que cette utilisation n'ait re-

çu l'agrément du fabricant.

• N'endommagez pas le circuit frigorifique.

• Le circuit frigorifique de l’appareil contient

de l’isobutane (R600a), un gaz naturel of-

frant un haut niveau de compatibilité avec

l’environnement mais qui est néanmoins in-

flammable.

Pendant le transport et l'installation de votre

appareil, assurez-vous qu'aucune partie du

circuit frigorifique n'est endommagée.

Si le circuit frigorifique est endommagé :

– évitez les flammes vives et toute autre

source d'allumage

– aérez soigneusement la pièce où se trou-

ve l'appareil

• Ne modifiez pas les spécifications de l'appa-

reil. Si le câble d'alimentation est endomma-

gé, il peut causer un court circuit, un incen-

die et/ou une électrocution.

Avertissement Les éventuelles répara-

tions ou interventions sur votre appareil,

ainsi que le remplacement du câble d'alimenta-

tion, ne doivent être effectuées que par un pro-

fessionnel qualifié.

1. Ne branchez pas le cordon d'alimenta-

tion à une rallonge.

2. Assurez-vous que la prise n'est pas

écrasée ou endommagée par l'arrière de

l'appareil. Une prise de courant écrasée

ou endommagée peut s'échauffer et

causer un incendie.

3. Vérifiez que la prise murale de l'appareil

est accessible.

4. Ne débranchez pas l'appareil en tirant

sur le câble.

5. Si la prise murale n'est pas bien fixée,

n'introduisez pas de prise dedans. Ris-

que d'électrocution ou d'incendie.

6. N'utilisez pas l'appareil sans le diffuseur

de l'ampoule (si présent) de l'éclairage

intérieur.

• Cet appareil est lourd. Faite attention lors de

son déplacement.

• Ne touchez pas avec les mains humides les

surfaces givrées et les produits congelés

(risque de brûlure et d'arrachement de la

peau).

• Évitez une exposition prolongée de l'appareil

aux rayons solaires.

• Les ampoules (si présentes) utilisées dans

cet appareil sont des ampoules spécifiques

uniquement destinées à être utilisées sur

des appareils ménagers. Elles ne sont pas

du tout adaptées à un éclairage quelconque

d'une habitation.

Utilisation quotidienne

• Ne posez pas d'éléments chauds sur les

parties en plastique de l'appareil.

• Ne stockez pas de gaz ou de liquides inflam-

mables dans l'appareil (risque d'explosion).

• Ne placez pas d'aliments directement contre

la sortie d'air sur la paroi arrière de l'appareil.

(Si l'appareil est sans givre.)

• Un produit décongelé ne doit jamais être re-

congelé.

• Conservez les aliments emballés conformé-

ment aux instructions de leur fabricant.

• Respectez scrupuleusement les conseils de

conservation donnés par le fabricant de l'ap-

pareil. Consultez les instructions respecti-

ves.

• Ne mettez pas de bouteilles ni de boîtes de

boissons gazeuses dans le compartiment

congélateur, car la pression se formant à l'in-

térieur du contenant pourrait le faire éclater

et endommager ainsi l'appareil.

• Ne consommez pas certains produits tels

que les bâtonnets glacés dès leur sortie de

l'appareil, car ils peuvent provoquer des brû-

lures.

Entretien et nettoyage

• Avant toute opération d'entretien, mettez

l'appareil hors tension et débranchez-le de la

prise de courant.

• N'utilisez pas d'objets métalliques pour net-

toyer l'appareil.

www.zanussi.com

• N'utilisez pas d'objet tranchant pour gratter

la couche de givre. Utilisez une spatule en

plastique.

• Contrôlez régulièrement l'orifice d'évacuation

de l'eau de dégivrage dans le compartiment

réfrigérateur. Nettoyez-le, si besoin. Si l'orifi-

ce est bouché, l'eau s'écoulera en bas de

l'appareil.

Installation

Important Avant de procéder au branchement

électrique, respectez scrupuleusement les

instructions fournies dans cette notice.

• Déballez l'appareil et vérifiez qu'il n'est pas

endommagé. Ne branchez pas l'appareil s'il

est endommagé. Signalez immédiatement au

revendeur de l'appareil les dommages cons-

tatés. Dans ce cas, gardez l'emballage.

• Il est conseillé d'attendre au moins quatre

heures avant de brancher l'appareil pour que

le circuit frigorifique soit stabilisé.

• Veillez à ce que l'air circule librement autour

de l'appareil pour éviter qu'il ne surchauffe.

Pour assurer une ventilation suffisante, res-

pectez les instructions de la notice (chapitre

Installation).

• Placez l'appareil dos au mur pour éviter tout

contact avec le compresseur et le conden-

seur (risque de brûlure).

• Placez de préférence votre appareil loin

d'une source de chaleur (chauffage, cuisson

ou rayons solaires trop intenses).

• Assurez-vous que la prise murale reste ac-

cessible après l'installation de l'appareil.

• Branchez à l'alimentation en eau potable uni-

quement. (Si un branchement sur le réseau

d'eau est prévu.)

Maintenance

• Les branchements électriques nécessaires à

l'entretien de l'appareil doivent être réalisés

par un électricien qualifié ou une personne

compétente.

• Cet appareil ne doit être entretenu et réparé

que par un Service après-vente autorisé, ex-

clusivement avec des pièces d'origine.

Protection de l'environnement

Le système frigorifique et l'isolation de vo-

tre appareil ne contiennent pas de C.F.C.

contribuant ainsi à préserver l'environnement.

L'appareil ne doit pas être mis au rebut avec

les ordures ménagères et les déchets urbains.

La mousse d'isolation contient des gaz inflam-

mables : l'appareil sera mis au rebut conformé-

ment aux règlements applicables disponibles

auprès des autorités locales. Veillez à ne pas

détériorer les circuits frigorifiques, notamment

au niveau du condenseur. Les matériaux utili-

sés dans cet appareil identifiés par le symbole

sont recyclables.

www.zanussi.com

Description de l'appareil

2 43 7 8 109

111314

5 61

Bacs à fruits

Clayette en verre

Thermostat

Compartiment à beurre

Balconnet de porte

Compartiment à bouteilles

Panier de congélation

Bac Maxibox

Panier de congélation

Plaque signalétique

Fonctionnement

Mise en fonctionnement

Branchez l'appareil sur une prise murale.

Tournez le bouton du thermostat dans le sens

des aiguilles d'une montre sur une position

moyenne.

Mise à l'arrêt

Pour mettre à l'arrêt l'appareil, tournez le bou-

ton du thermostat sur la position "O".

Réglage de la température

La température est réglée automatiquement.

Pour faire fonctionner l'appareil, procédez

comme suit :

www.zanussi.com

• tournez le bouton du thermostat vers le bas

pour obtenir un réglage de froid minimum.

• tournez le bouton du thermostat vers le haut

pour obtenir un réglage de froid maximum.

Une position moyenne est la plus indi-

quée.

Toutefois, le réglage doit être choisi en tenant

compte du fait que la température à l'intérieur

de l'appareil dépend de plusieurs facteurs :

• la température ambiante

• la fréquence d'ouverture de la porte

• la quantité de denrées stockées

• l'emplacement de l'appareil.

Important Si le thermostat est réglé sur la

position de froid maximum, lorsque la

température ambiante est élevée et que

l'appareil est plein, il est possible que le

compresseur fonctionne en régime continu.

Dans ce cas, il y a un risque de formation

excessive de givre sur la paroi postérieure à

l'intérieur de l'appareil. Pour éviter cet

inconvénient, placez le thermostat sur une

température plus élevée de façon à permettre

un dégivrage automatique et, par conséquent,

des économies de courant.

Première utilisation

Nettoyage intérieur

Avant d'utiliser l'appareil pour la première fois,

nettoyez l'intérieur et tous les accessoires in-

ternes avec de l'eau tiède savonneuse pour

supprimer l'odeur caractéristique du "neuf"

puis séchez soigneusement.

Important N'utilisez pas de produits abrasifs,

poudre à récurer, éponge métallique pour ne

pas abîmer la finition.

Utilisation quotidienne

Congélation d'aliments frais

Le compartiment congélateur est idéal pour

congeler des denrées fraîches et conserver les

aliments surgelés ou congelés pendant long-

temps.

Pour congeler des aliments frais, il n'est pas

nécessaire de modifier le réglage moyen.

Toutefois, pour une congélation plus rapide,

tournez le thermostat vers le haut pour obtenir

plus de froid.

Important Dans ce cas, la température du

compartiment réfrigérateur peut chuter au-

dessous de 0°C. Si cela se produit,

repositionnez le thermostat sur un réglage plus

chaud.

Placez les denrées fraîches à congeler dans le

compartiment inférieur.

Conservation d'aliments congelés

À la mise en service ou après un arrêt prolon-

gé, faites fonctionner l'appareil pendant 2 heu-

res environ, avant d’introduire les produits dans

le compartiment.

Les tiroirs de congélation vous permettent de

trouver facilement et rapidement les aliments

dont vous avez besoin. Si vous devez stocker

une grande quantité d'aliments, retirez tous les

tiroirs et le bac à glace sauf le tiroir inférieur qui

doit être en place afin de permettre une circu-

lation d'air optimale. Des denrées alimentaires

peuvent être stockées sur chaque clayette en

respectant un espace de 15 mm max. à partir

de la porte.

Important En cas de décongélation

accidentelle, due par exemple à une coupure

de courant, si la coupure a duré plus de temps

qu'il n'est prévu au paragraphe « Autonomie de

fonctionnement », au chapitre Caractéristiques

techniques, consommez rapidement les

aliments décongelés ou cuisez-les

immédiatement avant de les recongeler (une

fois refroidis).

Décongélation

Avant utilisation, les aliments surgelés ou con-

gelés peuvent être décongelés dans le com-

www.zanussi.com

partiment du réfrigérateur ou à température

ambiante en fonction du temps disponible pour

cette opération.

Les petites portions peuvent même être cuites

sans décongélation préalable (la cuisson sera

cependant un peu plus longue).

Clayettes amovibles

Les parois du réfrigérateur sont équipées d'une

série de glissières pour que les clayettes puis-

sent être placées en fonction des besoins.

Emplacement des balconnets de la porte

Les balconnets de porte peuvent être placés à

différentes hauteurs pour permettre le range-

ment d'aliments de différentes tailles.

Tirez progressivement le balconnet dans le

sens des flèches pour le dégager, puis reposi-

tionnez-le selon les besoins.

Retrait des paniers de congélation du

congélateur

Les paniers de congélation sont équipés d'un

arrêt afin d'empêcher leur retrait accidentel ou

chute. Pour retirer le panier du congélateur, ti-

rez-le vers vous et en atteignant l'arrêt, retirez-

le en inclinant la partie avant vers le haut.

Pour le remettre, relevez légèrement l'avant du

panier et insérez-le dans le congélateur. Une

fois que vous avez dépassé les butées d'arrêt,

poussez les paniers dans la bonne position.

Conseils utiles

Bruits de fonctionnement normaux

• Le liquide de refroidissement qui passe dans

le circuit d'évaporation peut produire un bruit

de gargouillis ou de bouillonnement. Ce

phénomène est normal.

• Le compresseur peut produire un ronronne-

ment aigu ou un bruit de pulsation. Ce phé-

nomène est normal.

• La dilatation thermique peut provoquer un

soudain, léger bruit de craquement. C'est un

phénomène normal et sans gravité. Ce phé-

nomène est normal.

• Un léger claquement se produit lors de la

mise en fonctionnement/à l'arrêt du com-

presseur. Ce phénomène est normal.

Conseils pour l'économie d'énergie

• N'ouvrez pas la porte trop souvent ou plus

longtemps que nécessaire.

www.zanussi.com

La page charge ...

Zanussi ZRB934PW2 Manuel utilisateur

Marque: Zanussi

Modèle: ZRB934PW2

Catégorie: Réfrigérateurs-congélateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZRB934PW2 User manual

Zanussi ZRB934PW2 Manuel utilisateur

Zanussi ZRB934PW2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents