Setra Systems Power Meter (Multi-Load) Mode d'emploi

Marque: Setra Systems

Modèle: Power Meter (Multi-Load)

Taper: Mode d'emploi

Power Meter

Operating Instructions

Setra Systems, Inc.

159 Swanson Road, Boxborough, MA 01719

800.257.3872 • www.setra.com

BACnet is a registered trademark of the American Society of Heating, Refrigerating, and Air-

Conditioning Engineers (ASHRAE).

The material in this document is for information purposes only and is subject to change

without notice. Setra Systems assumes no responsibility for any errors or for consequential

damages that may result from the use or misrepresentation of any of the material in this

publication.

Table of Contents

1.0 Introduction .................................................................................................................... 8

 .................................................................. 8

1.2 Field selectable communication............................................................................... 8

1.3 Intended use .............................................................................................................. 8

1.4 Product differentiation .............................................................................................. 9

1.5 Product unpacking ..................................................................................................10

2.0 Safety information ......................................................................................................11

2.1 Safety symbols ........................................................................................................ 11

2.2 Please note ..............................................................................................................11

2.3 Safety approval ........................................................................................................11

2.4 General safety requirements................................................................................... 13

2.5 Power Meter installation safety requirements....................................................... 13

3.0 Meter overview ............................................................................................................. 17

3.1 Installation overview ...............................................................................................22

3.2 Main assembly and back housing separation/attachment .................................. 22

4.0 Planning for installation ..............................................................................................24

 ................................................................................. 24

4.2 Meter installation overview .....................................................................................24

.................................................................24

4.4 RTU programming and script overview ..................................................................25

5.0 Changing conduit position ..........................................................................................25

 .....................................................................................................26

7.0 Connecting high voltage inputs ..................................................................................27

8.0 Current transformer wiring .......................................................................................... 34

9.0 CTs wiring example ...................................................................................................... 39

10.0 EIA-485 communication wiring ................................................................................40

11.0 Ethernet communication wiring ................................................................................ 42

Table of Contents

12.0 Pulse inputs wiring ....................................................................................................43

12.1 Pulse output wiring ...............................................................................................43

13.0 Alarm relay (SPDT) wiring ......................................................................................... 44

14.0 Installing front cover ................................................................................................. 45

 ...................................................................................................46

 ........................................................46

 .......................................................................46

15.3 Connect the Meter ................................................................................................. 46

15.4 Web portal setup ...................................................................................................47

15.5 Web portal overview .............................................................................................. 47

15.6 Meter communication bar ....................................................................................48

15.7 Menu navigation sidebar ......................................................................................48

16.0 Halo-dot ....................................................................................................................49

 ................................................................................. 49

16.2 Halo ........................................................................................................................ 49

16.3 Numerical indication ............................................................................................. 49

17.0 Setup menu ................................................................................................................50

18.0 Setup menu help legend ............................................................................................ 51

19.0 General settings ......................................................................................................... 52

19.1 Device setting within the Device settings section ...............................................52

19.2 General Settings .................................................................................................... 53

19.3 Site information .....................................................................................................57

19.4 Uploading to meter ................................................................................................57

20.0 Voltage inputs ............................................................................................................58

21.0 Load setup ..................................................................................................................62

 ................................................................................................ 63

21.2 Visual load indication ............................................................................................64

22.0 CT inputs ....................................................................................................................65

23.0 Communications/Network settings .........................................................................71

Table of Contents

23.1 Network settings ...................................................................................................73

24.0 Pulse IO setup ............................................................................................................74

24.1 Pulse output ..........................................................................................................75

25.0 Alarm setup ................................................................................................................ 79

25.1 Over power .............................................................................................................80

25.2 Under power ..........................................................................................................80

25.3 Energy usage (Vin) ................................................................................................81

25.4 Energy usage (Load) .............................................................................................81

25.5 Polarity CT .............................................................................................................82

25.6 Under voltage ........................................................................................................82

25.7 Under current CT ...................................................................................................83

25.8 Over current CT ...................................................................................................... 83

25.9 Phase loss CT ........................................................................................................ 84

25.10 Over voltage .........................................................................................................84

25.11 Over current (Load) .............................................................................................85

25.12 Peak demand (Load) ........................................................................................... 85

25.13 Low power factor ................................................................................................86

25.14 Summary alarm table..........................................................................................86

26.0 Installation report ......................................................................................................87

26.1 General information ..............................................................................................87

26.2 Meter information..................................................................................................88

26.3 General notes ........................................................................................................88

26.4 Measurements.......................................................................................................89

26.5 Export the report ....................................................................................................90

27.0 Power analytics ..........................................................................................................90

27.1 Parameters within Trends & Odometer menus ................................................... 90

Table of Contents

27.2 Trends ....................................................................................................................91

27.3 Odometer ...............................................................................................................93

 .........................................................................................94

27.5 Export logged data ................................................................................................94

28.0 Event Log ................................................................................................................... 95

29.0 Alarm status ............................................................................................................... 96

29.1 Active alarm states ...............................................................................................96

29.2 Active LED states ..................................................................................................96

29.3 Active relay states .................................................................................................96

29.4 Alarm log ................................................................................................................96

29.5 Export of Alarm Logs.............................................................................................97

29.6 Example of Alarm Logs Record ............................................................................97

30.0 System ........................................................................................................................98

30.1 Software version ...................................................................................................98

30.2 Factory reset ..........................................................................................................98

30.3 Trend data rest ......................................................................................................99

30.4 Reboot ....................................................................................................................99

30.5 System log ............................................................................................................. 99

 ................................................................................................100

 ...........................................................................................100

 ........................................................................101

31.3 Clone/Import meter setup ..................................................................................101

32.0 Help ...........................................................................................................................102

33.0 Troubleshooting ....................................................................................................... 102

34.0 Replace battery ........................................................................................................103

35.0 User interface ........................................................................................................... 105

36.0 Main Menu ................................................................................................................105

37.0 Real-time values ......................................................................................................106

38.0 Odometer .................................................................................................................. 107

Table of Contents

 ............................................................................................................108

40.0 Communication ....................................................................................................... 109

41.0 Network ....................................................................................................................110

42.0 Alarm ........................................................................................................................111

43.0 About ........................................................................................................................112

44.0 Factory reset at meter .............................................................................................113

45.0 Returning products for repair ..................................................................................114

46.0 Limited warranty & limitation of repair ...................................................................114

47.0 Equipment service & access ...................................................................................115

47.1 Access to equipment ..........................................................................................115

47.2 Servicing the equipment .....................................................................................115

47.3 Component servicing ..........................................................................................115

48.0 Support ..................................................................................................................... 115

48.1 Setra contact .......................................................................................................115

1.3 Intended use

Setra Power Meter is designed to closely monitor and provide detailed information of the

building and/or equipment. The meter can be used in varying capacities, measuring varying

loads with up to two different voltage reference points. Typical applications include measuring

power of buildings, leased building space, large machinery or equipment, lighting loads, and

more.

The meter will monitor and provide visual indicators on the Backlit Display, Error Indication

LED and Power Indication LED.

Each Power Meter comes standard with eld selectable BACnet and Modbus communication

protocols. The communications interface is through either an EIA-485 serial connection

(BACnet MS/TP or Modbus RTU) or over Ethernet (BACnet/IP or Modbus TCP). Along with

these advanced network communication protocols, the Power Meter offers one congurable

pulse output and two congurable pulse inputs, enabling more data collection at the meter.

1.0 Introduction

The Power Meter from Setra is a networked revenue grade power meter built on a versatile

and powerful platform designed to meet the high demands for any submetering application.

Available in a 3, 12 or 48 load congurations, the meter enclosure & intuitive web portal

interface signicantly reduce installation time and cost per metering point. The Power

Meter 12 & 48 load meters come standard with dual voltage inputs, and all versions are eld

congurable for use of standard or Rogowski style current transformers, enabling safe and

accurate measurement of both low and high amperage services.

The Setra Power Meter can be ordered in the following congurations, which are identiable

on the part number label.

[1] [2] [3] [4] [5]

Model

SPM Power Meter

[1]

Loads

03 3 loads

12 12 loads

48 48 loads

[2]

Communication

E Ethernet & serial

[3]

Display

D Onboard display

Option

N None

[4]

[5]

1.1 Web Portal meter setup & conguration

Setup is both intuitive and time-saving through the Setra Power Meter Web Portal. The software

can be easily accessed through the meter itself, either through simple USB connection to your

PC or through Ethernet connection over a shared network.

1.2 Field selectable communication

Integration with building automation systems is made easy through eld selectable BACnet

and Modbus communication protocols. The meter’s communications interface is enabled

through either an EIA-485 serial connection (BACnet MS/TP or Modbus RTU) or over

Ethernet (BACnet/IP of or Modbus TCP). Along with these advanced network communication

protocols, the Setra Power Meter offers a connection interface with adjacent equipment

through one congurable pulse output and two congurable pulse inputs, enabling even more

data collection through the meter.

1.4 Product differentiation

The Setra Power Meter has been designed in three different “Load” congurations, with

following differences in each product:

3 Load:

• Three CT terminal blocks

• One voltage input terminal block

• 6.8” x 7” x 3.8” form factor

• Six conduit openings

12 Load:

• Twelve CT terminal blocks

• Two voltage input terminal blocks

• 6.8” x 7” x 3.8” form factor

• Six conduit openings

48 Load:

• Forty-eight CT terminal blocks

• Two voltage input terminal blocks

• 10.8” x 17.2” x 4.4” form factor

• Fifteen conduit openings

1.5 Product unpacking

Item

P/N: SPM03EDN

Included w/ meter

P/N: SPM12EDN

Included w/ meter

P/N: SPM48EDN

Included w/ meter

Power Meter 1 1 1

CT connector 4 13 49

Hardware kit 1 1 1

 1 1 1

Auxiliary equipment & hardware kit contents

CT connector kit

Mounting screws Wall anchors

Cable ties

Cal. Cert.

Preparing for install

What's in the box

3/12 Load

Remove meter from box

Flip open dust cover Pull front cover forward

Insert screwdriver

into slot

Pivot screwdriver up to

remove main assemble

Pull down on tabs

48 Load



 



2.0 Safety Information

Read these instructions carefully and look at the equipment to become familiar with the

device before trying to install, operate, service or maintain it. The following special messages

may appear throughout this manual or on the equipment to warn of potential hazards or to

call attention to information that claries or simplies a procedure.

Denotes warning or caution. See manual for a description of the meanings.

DENOTES HIGH VOLTAGE. RISK OF ELECTRICAL SHOCK. LIFE

THREATENING VOLTAGES MAY BE PRESENT. QUALIFIED PERSONNEL ONLY.

Equipment protected throughout by double insulation (IEC 536 Class II)

Contains additional information pertinent to current subject.

2.2 Please note

Electrical equipment should be installed, operated, serviced and maintained only by qualied

personnel. No responsibility is assumed by Setra for any consequences arising out of the

use of this material. A qualied person is one who has skills and knowledge related to the

construction, installation, and operation of electrical equipment and has received safety

training to recognize and avoid the hazards involved.

2.3 Safety approval

The Setra Networked Multi-load Power Meter is UL listed and complies with the following

safety standards for 600V CAT III Pollution Degree 2:

UL 61010-1 Edition 3 (2016),

CSA C22.2 No 61010-1-12 Edition 3 Update 2 (2016),

IEC/EN61010-1 Edition 3 (2013),

Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use,

Part 1: General requirements

UL 61010-2-030 Edition 2,

CSA C22.2 No 61010-2-030-12 Edition 1 (2012),

IEC/EN61010-2-030 Edition 1 (2011),

Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use,

Part 2-030: Particular Requirements for Testing and Measuring Circuits

2.1 Safety symbols

The following international symbols are used on the Power Meter and in this manual:

E503021

LISTED

2.0 Informations de sécurité

Lisez attentivement ces instructions et examinez l'équipement pour vous familiariser avec

l'appareil avant d'essayer de l'installer, de le faire fonctionner, de le réparer ou de l'entretenir.

Les messages spéciaux suivants peuvent apparaître dans ce manuel ou sur l'équipement

pour avertir des dangers potentiels ou pour attirer l'attention sur des informations qui clarient

ou simplient une procédure.

Indique un avertissement ou une prudence. Voir le manuel pour une

description des signications.

INDIQUE HAUTE TENSION. RISQUE DE CHOC ÉLECTRIQUE. DES TENSIONS

MENACANTES POUR LA VIE PEUVENT ÊTRE PRÉSENTES. PERSONNEL

QUALIFIÉ UNIQUEMENT.

Équipement protégé partout par une double isolation (IEC 536 classe II)

Contient des informations supplémentaires pertinentes au sujet actuel.

2.2 Veuillez noter

L'équipement électrique doit être installé, utilisé, entretenu et entretenu uniquement par

du personnel qualié. Aucune responsabilité est assumée par Setra des conséquences

découlant de l'utilisation de ce matériel. Une personne qualiée est une personne qui

possède des compétences et des connaissances liées à la construction, à l'installation et

au fonctionnement de l'équipement électrique et qui a reçu une formation en sécurité pour

reconnaître et éviter les dangers impliqués.

2.3 Approbation de sécurité

Le Setra Networked Multi-Load Power Meter est UL et conforme aux normes de sécurité

suivantes pour 600V CAT III Degré de pollution 2:

UL 61010-1 Edition 3 (2016),

CSA C22.2 No 61010-1-12 Edition 3 Update 2 (2016),

IEC/EN61010-1 Edition 3 (2013),

Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use,

Part 1: General requirements

UL 61010-2-030 Edition 2,

CSA C22.2 No 61010-2-030-12 Edition 1 (2012),

IEC/EN61010-2-030 Edition 1 (2011),

Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use,

Part 2-030: Particular Requirements for Testing and Measuring Circuits

2.1 Symboles de sécurité

Les symboles internationaux suivants sont utilisés sur le Power Meter et dans ce manuel:

Français

E503021

LISTED

Input supply rating: 80-600 Vac (Vin1 L1 & L2), 50/60 Hz, 5W max, Overvoltage Category III

Voltage measurement:

Three phase max. 347/600 Vac WYE earthed

Three phase max. 347 Vac DELTA earthed/unearthed

Split phase max. 240/480 Vac

Single phase max. 480 Vac

Measurement Category III

Frequency measurement:

50/60 Hz

Current measurement:

Up to 6000 A (through use of CTs or Rogowski coils with voltage output up to 2V)

Alarm relay output ratings: 30 Vdc/ac, 2 Arms, resistive, Class 2

Pulse I/O: 30 Vdc

UL Safety Ratings

Equipment function Networked Multi-circuit power meter

Connection to mains supply Permanently

Overvoltage/ Measurement category III

Pollution degree 2

Means of protection Class II (double insulated)

Environmental condition

Temperature:

Humidity:

Altitude:

-20°C to +60°C

5% to 95% non-condensing humidity

Max. 2000 meters

For use in wet location No

Equipment mobility Wall/surface mounted

Operating conditions Continuous

Marked degree of protection Type 1

Capacité d'alimentation d'entrée: 80-600 Vac (Vin1 L1 & L2), 50/60 Hz, 5W max, catégorie

de surtension III

Mesure de tension:

Triphasé max. 347/600 Vac WYE mis à terre

Triphasé max. 347 Vac DELTA mis à la terre / déterré

Phase divisée max. 240/480 Vac

Monophasé max. 480 Vac

Catégorie de mesure III

Mesure de fréquence:

50/60 Hz

Mesure de courant:

Jusqu'à 6000 A (grâce à l'utilisation de TC ou de bobines Rogowski avec une tension de

sortie jusqu'à 2 V)

Évaluations de sortie de relais d'alarme: 30 Vdc / ac, 2 bras, résistif, classe 2

Puissance d'entrée / sortie d'impulsion: 30 Vdc

Évaluations de sécurité UL

Fonction d'équipement

Compteur de puissance multi-circuits

en réseau

Connexion à l'alimentation principale Connecté en permanence

Surtension / Catégorie de mesure III

Degré de pollution 2

Moyens de protection Class II (double isolation)

Conditions environnementales

Température:

Humidité:

Altitude:

-20°C à +60°C

5% à 95% d'humidité sans condensation

Max. 2000 mètres

Pour une utilisation dans des

endroits humides

Non

Mobilité de l'équipement Montage mural / en surface

Conditions de fonctionnement Continu

Degré de protection marqué Type 1

Français

General safety requirements

To ensure the safe operation and service of the device, follow these instructions

closely. Failure to observe warnings can result in severe personal injury or

permanent damage to the device.

• Review the entire manual before use of the Meter and its accessories.

• Comply with local and national safety codes. Use personal protective equipment to

prevent shock and arc flash injury where hazardous live conductors are exposed.

• Only licensed electricians should install this equipment. Such work should be performed

only after reading this entire set of instructions.

• The equipment must be accessible to authorized personnel only. Equipment must be

installed in areas where access can be restricted.

• If the meter appears damaged or defective or internal fuse blowout, rst disconnect all

power to the meter. Then contact Setra technical support for assistance.

• If the products are used in a manner not specied by Setra, the protection provided by

the equipment may be impaired.

Power Meter installation safety requirements

FCC PART 15 Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in an installation

• Use copper conductors only.

• Wiring to voltage input terminals and mains shall have minimal temperature rating of

90°C (194°F) and minimal wire gauge of 14 AWG (1.63 mm).

• External secondary inputs and outputs should be connected to devices meeting the

requirements of IEC 60950.

• For use only with Listed Energy-Monitoring Current Transformers

• Warning - To reduce risk of electric shock, always open or disconnect circuit from power-

distribution system (or service) of building before installing or servicing current-sensing

transformers

• Current transformers may not be installed in equipment where they exceed 75 percent of

the wiring space of any cross-sectional area within the equipment.

• Current transformers may not be installed in an area where they block ventilation

openings.

• Current transformers may not be installed in an area of breaker arc venting.

• Current transformers are not suitable for Class 2 wiring method nor intended for

connection to Class 2 equipment.

• Secure current transformer and route conductors so that they do not directly contact live

terminals or bus.

• Wiring to terminal blocks shall have minimal temperature rating at least 75°C (167°F)

• When connecting power meter to conduit, a threaded hub shall be installed at conduit

entrances. When using rigid conduit connect the hub to the conduit before connecting

to power meter enclosure.

Règles générales de sécurité

Pour garantir le fonctionnement et l'entretien en toute sécurité de l'appareil, suivez

attentivement ces instructions. Le non-respect des avertissements peut entraîner

des blessures graves ou des dommages permanents à l'appareil.

• Revoir le manuel en entier avant l'utilisation de l'appareil et de ses accessoires.

• Respectez les codes de sécurité locaux et nationaux. Utilisez un équipement de protection

individuelle pour éviter les chocs et les arcs électriques lorsque des conducteurs sous tension

dangereux sont exposés.

• Seuls des électriciens agréés doivent installer cet équipement. Un tel travail ne doit être effectué

qu'après avoir lu l'ensemble de ces instructions.

• L'équipement doit être accessible uniquement au personnel autorisé. L'équipement doit être

installé dans des zones où l'accès peut être restreint.

• Si le compteur semble endommagé ou défectueux ou que le fusible a sauté, débranchez d'abord

l'alimentation du compteur. Contactez ensuite le support technique de Setra pour obtenir de l'aide.

• Si les produits sont utilisés d'une manière non spéciée par Setra, la protection fournie par

l'équipement peut être altérée.

Règles de sécurité pour l'installation du Power Meter

Avis FCC PARTIE 15

Cet équipement a été testé et déclaré conforme aux limites d'un appareil numérique de classe B, conformément

à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les

interférences nuisibles lorsque l'équipement est utilisé dans un environnement commercial. Cet équipement

génère, utilise et peut émettre de l'énergie radiofréquence et, s'il n'est pas installé et utilisé conformément

aux instructions, peut provoquer des interférences nuisibles aux communications radio. Cependant, il n'y a

aucune garantie qu'aucune interférence ne se produira dans une installation.

• Utilisez uniquement des conducteurs en cuivre.

• Le câblage aux bornes d'entrée de tension et au secteur doit avoir une température nominale

minimale de 90 ° C (194 ° F) et un calibre de l minimal de 14 AWG (1,63 mm).

• Les entrées et sorties secondaires externes doivent être connectées à des appareils répondant

aux exigences de la CEI 60950.

• À utiliser uniquement avec les transformateurs de courant à surveillance d'énergie répertoriés

• Avertissement - Pour réduire le risque de choc électrique, ouvrez ou déconnectez toujours le circuit

du système de distribution électrique (ou du service) du bâtiment avant d'installer ou d'entretenir

des transformateurs de détection de courant

• Les transformateurs de courant ne doivent pas être installés dans l'équipement où ils dépassent

75 pour cent de l'espace de câblage de toute section transversale de l'équipement.

• Les transformateurs de courant ne doivent pas être installés dans une zone où ils bloquent les

ouvertures de ventilation.

• Les transformateurs de courant ne doivent pas être installés dans une zone d'évacuation d'arc du

discontacteur.

• Les transformateurs de courant ne sont pas adaptés à la méthode de câblage de classe 2 ni

destinés à être connectés à un équipement de classe 2.

• afxez le transformateur de courant et circulez les conducteurs an qu'ils n'entrent pas directement

en contact avec les bornes sous tension ou le bus.

• Le câblage aux borniers doit avoir une température nominale minimale d'au moins 75 ° C (167 ° F)

• Lors de la connexion du wattmètre au conduit, un moyeu fileté doit être installé aux entrées

du conduit. Lorsque vous utilisez un conduit rigide, connectez le moyeu au conduit avant de le

connecter au boîtier du wattmètre.

Français

3.0 Meter overview

This section is intended so that you can familiarize yourself with the features of the meter prior

to installation, while size and amount of current transformer connection differ most features

and terminology remain the same between the 3, 12, and 48 load power meters.

Power meter sections

(12 load meter shown)

Conduit plug x2 high

voltage area

Main assembly

Back housing

Front housing

Conduit knockout

CT area x4

Mounting holes (x4)

CT inputs

3/12-load meter

CT Inputs

x3 (3 Load meter)

x6 (12 Load meter)

SPDT alarm relay

EIA-485

communication

terminal

Ethernet RJ45

connection

Earth ground

screw terminal

(optional)

Pulse IO

Input x2

Output x1

Low voltage

conduit entry

CT inputs x6

(12 Load only)

High voltage

conduit entry

Low voltage

conduit entry

High voltage

conduit entry

Earth ground Screw: In noisy environments connect earth ground terminal to electrical panel earth ground to reduce noise

pickup

177.1

7.0

173.9

6.8

95.9

3.8

4.7

.19

(X4)

13.1

162.1

6.4

50.9

2.0

122.9

4.8

PART #

REV.

DATE

REVISION RECORD

FILE:

DWG SIZE

> 6" = ±1/16

DO NOT SCALE DRAWING

< 6" = ±1/32

THIRD ANGLE

PROJECTION

ANGULAR

± 0° 30"

FRACTIONAL

TOLERANCES

EXCEPT AS NOTED

DECIMAL

XX = ±.01

MATERIAL

DRAWING NUMBER

TITLE

SCALE

ENGR

REV.

DATE

REV

APPROVALS

DESCRIPTION

DATE

Boxborough, MA, 01719

MATERIAL

1:2

INITIALS

NAME

DATE

12 Ch.DRW

DRAWN BY

XXX = ±.005

1 of 1

SHEET

DOLAN-JENNER INDUSTRIES, INC.

TEL. (978) 263-1400 FAX. (978) 266-1618

PROPRIETARY INFORMATION OF SETRA SYSTEMS, INC., ALL

RIGHTS RESERVED. ALL UNAUTHORIZED REPRODUCTION,

USE AND TRANSMISSION OF THIS DRAWING AND

INFORMATION IT CONTAINS ARE STRICTLY PROHIBITED.

THIS DRAWING IS SUBJECT TO RETURN TO SETRA SYSTEMS, INC.,

UPON ITS REQUEST.

6.8

[173.9]

7.0

[177.1]

3.8

[95.9]

3/4” (Conduit

Opening)

3/4” (Conduit

Opening)

Dimensions

48-Load Meter

CT input x6

DIP switches

(EIA-485 Config)

Low voltage

conduit entry

SPDT alarm

relay

Earth ground

screw terminal

(optional)

Mounting hole

Pulse I/O

Input x2

Output x1

EIA-485

Communication

terminal

Ethernet RJ45

Connection

CT input x6

High voltage

conduit entry

Low voltage

conduit entry x5

High voltage

conduit entry

435.7

17.2

274.9

10.8

112

4.4

.20

(X5)

27.8

1.1

332.6

13.1

29.5

1.2

137.4

5.4

245.4

9.7

PART #

REV.

DATE

REVISION RECORD

FILE:

DWG SIZE

> 6" = ±1/16

DO NOT SCALE DRAWING

< 6" = ±1/32

THIRD ANGLE

PROJECTION

ANGULAR

± 0° 30"

FRACTIONAL

TOLERANCES

EXCEPT AS NOTED

DECIMAL

XX = ±.01

MATERIAL

DRAWING NUMBER

TITLE

SCALE

ENGR

REV.

DATE

REV

APPROVALS

DESCRIPTION

DATE

Boxborough, MA, 01719

MATERIAL

1:4

INITIALS

NAME

DATE

48 Ch.DRW

DRAWN BY

XXX = ±.005

1 of 1

SHEET

DOLAN-JENNER INDUSTRIES, INC.

TEL. (978) 263-1400 FAX. (978) 266-1618

PROPRIETARY INFORMATION OF SETRA SYSTEMS, INC., ALL

RIGHTS RESERVED. ALL UNAUTHORIZED REPRODUCTION,

USE AND TRANSMISSION OF THIS DRAWING AND

INFORMATION IT CONTAINS ARE STRICTLY PROHIBITED.

THIS DRAWING IS SUBJECT TO RETURN TO SETRA SYSTEMS, INC.,

UPON ITS REQUEST.

435.7

17.2

274.9

10.8

112

4.4

.20

(X5)

27.8

1.1

332.6

13.1

29.5

1.2

137.4

5.4

245.4

9.7

PART #

REV.

DATE

REVISION RECORD

FILE:

DWG SIZE

> 6" = ±1/16

DO NOT SCALE DRAWING

< 6" = ±1/32

THIRD ANGLE

PROJECTION

ANGULAR

± 0° 30"

FRACTIONAL

TOLERANCES

EXCEPT AS NOTED

DECIMAL

XX = ±.01

MATERIAL

DRAWING NUMBER

TITLE

SCALE

ENGR

REV.

DATE

REV

APPROVALS

DESCRIPTION

DATE

Boxborough, MA, 01719

MATERIAL

1:4

INITIALS

NAME

DATE

48 Ch.DRW

DRAWN BY

XXX = ±.005

1 of 1

SHEET

DOLAN-JENNER INDUSTRIES, INC.

TEL. (978) 263-1400 FAX. (978) 266-1618

PROPRIETARY INFORMATION OF SETRA SYSTEMS, INC., ALL

RIGHTS RESERVED. ALL UNAUTHORIZED REPRODUCTION,

USE AND TRANSMISSION OF THIS DRAWING AND

INFORMATION IT CONTAINS ARE STRICTLY PROHIBITED.

THIS DRAWING IS SUBJECT TO RETURN TO SETRA SYSTEMS, INC.,

UPON ITS REQUEST.

10.8

[274.9]

17.2

[435.7]

4.4

[112]

3/4”

in.

[mm]

Top view

Bottom view

1” Conduit Opening

Dimensions

1” Conduit

Opening

Display interface

Power indication

LED

Error indication

LED

4-Line backlit

display

Type B port USB

Simple 6-key

user-interface

La page charge ...

Setra Systems Power Meter (Multi-Load) Mode d'emploi

Marque: Setra Systems

Modèle: Power Meter (Multi-Load)

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Setra Systems Power Meter (Multi-Load) Operating instructions

Setra Systems Power Meter (Multi-Load) Mode d'emploi

Setra Systems Power Meter (Multi-Load) Mode d'emploi

dans d''autres langues

Autres documents