MSA Z-Gard® DS MPO Dual Gas Sensor Le manuel du propriétaire

Marque: MSA

Modèle: Z-Gard® DS MPO Dual Gas Sensor

Taper: Le manuel du propriétaire

Ce manuel convient également à

Z-Gard® S MPO Single Gas Sensor

ZGARD S & DS Gas Sensors

(with Magnetic Calibration)

Instruction Manual for RS-485-MPO Sensors

(Multi-Protocol: BACnet, MODBUS, ZGard, Apogee)

WARNING

THIS MANUAL MUST BE CAREFULLY READ BY ALL INDIVIDUALS WHO HAVE OR WILL HAVE THE

RESPONSIBILITY FOR INSTALLING, USING OR SERVICING THIS PRODUCT. Like any piece of complex equipment,

this product will perform as designed only if installed, used and serviced in accordance with the manufacturer’s

instructions. OTHERWISE, IT COULD FAIL TO PERFORM AS DESIGNED AND PERSONS WHO RELY ON THIS

PRODUCT FOR THEIR SAFETY COULD SUSTAIN SEVERE PERSONAL INJURY OR DEATH.

The warranties made by Mine Safety Appliances Company with respect to these Products are voided if the products

are not installed, used and serviced in accordance with the instructions in this user guide. Please protect yourself

and others by following them. We encourage our customers to write or call regarding this equipment prior to use or

for any additional information relative to use or repair.

Manual d’instructions

AVERTISSEMENT

Veuillez lire attentivement les instructions qui suivent. Tous ceux qui sont responsables, ou qui aurons la

responsabilité pour l’installation, la fonctionnalité ou l’usage de ce produit doivent se familiariser complètement

avec ses instructions. Comme tout appareil complexifié, ce produit peut vous donner les résultats anticipés

seulement s’il est installé, usagé et que le service d’entretien sont effectués d’après les instructions du fabricant

(ou manufacturier). Sous peine de ne pas suivre les instructions ci-incluses, il est possible que cet appareil vous

donne des résultats insuffisant. En conséquence, les personnes qui dépendront sur ce produit pour leur sécurité

peuvent être blessés ou mourir.

Les garanties de ‘Mine Safety Appliances Company’ par rapport à ces produits sont annulés si les produits ne sont

pas installés, usagés et le service maintenus conformément aux instructions ci-incluses. Veuillez vous protéger

ainsi que les autres, en suivant les instructions d’installations. S’il vous plaît, entrez en communications avec nous

au sujet de ce produit avant l’utilisation de ce produit ou pour plus amples renseignements, sois pour l’usage ou

les réparations.

In North America., to contact your nearest stocking location, dial toll-free 1-800-MSA-INST

To contact MSA International, dial (724) 776-8626

This manual is available on the internet at www.MSAsafety.com

Manufactured by

MSA NORTH AMERICA

1000 Cranberry Woods Drive, Cranberry Township, PA 16066

Rev. 1.4

MSA

Permanent Instrument Warranty

1. Warranty- Seller warrants that this product will be free from mechanical defect or faulty

workmanship for a period of eighteen (18) months from date of shipment or one (1) year from

installation, whichever occurs first, provided it is maintained and used in accordance with Seller’s

instructions and/or recommendations. This warranty does not apply to expendable or consumable

parts whose normal life expectancy is less than one (1) year such as, but not limited to, non-

rechargeable batteries, filament units, filter, lamps, fuses etc. The Seller shall be released from all

obligations under this warranty in the event repairs or modifications are made by persons other than

its own or authorized service personnel or if the warranty claim results from physical abuse or misuse

of the product. No agent, employee or representative of the Seller has any authority to bind the Seller

to any affirmation, representation or warranty concerning the product. Seller makes no warranty

concerning components or accessories not manufactured by the Seller, but will pass on to the

Purchaser all warranties of manufacturers of such components. THIS WARRANTY IS IN LIEU OF

ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, AND IS STRICTLY

LIMITED TO THE TERMS HEREOF. SELLER SPECIFICALLY DISCLAIMS ANY WARRANTY OF

MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.

2. Exclusive Remedy- It is expressly agreed that Purchaser’s sole and exclusive remedy for breach

of the above warranty, for any tortious conduct of Seller, or for any other cause of action, shall be the

repair and/or replacement at Seller’s option, of any equipment or parts thereof, which after

examination by Seller is proven to be defective. Replacement equipment and/or parts will be provided

at no cost to Purchaser, F.O.B. Seller’s Plant. Failure of Seller to successfully repair any

nonconforming product shall not cause the remedy established hereby to fail of its essential purpose.

3. Exclusion of Consequential Damage- Purchaser specifically understands and agrees that under

no circumstances will seller be liable to purchaser for economic, special, incidental or consequential

damages or losses of any kind whatsoever, including but not limited to, loss of anticipated profits and

any other loss caused by reason of non-operation of the goods. This exclusion is applicable to claims

for breach of warranty, tortuous conduct or any other cause of action against seller.

General Warnings

WARNING

1. The ZGARD S & DS gas sensors described in this

manual must be installed, operated, and maintained in

strict accordance with the labels, cautions, warnings,

instructions, and within the limitations stated.

2. The ZGARD S & DS gas sensors must not be

installed in outdoor areas or in locations where

explosive concentrations of combustible gases or

vapors might occur in the atmosphere: Class 1, Group

A, B, C, and D areas as defined by the NEC. Because

the gas sensors are not explosion-proof, they must be

located in non-hazardous areas. The ZGARD S & DS

gas sensor must not be subject to direct sunlight or

equivalent.

3. Do not paint the ZGARD S & DS gas sensors.

Cleaning must be with warm water only (no cleaning

solutions).

4. The only absolute method to assure the proper overall

operation of a gas detection instrument is to check it

with a known concentration of the gas for which it has

been calibrated. Consequently, a calibration check

must be included as part of the installation and as a

routine inspection of the system.

5. Use only genuine MSA replacement parts when

performing any maintenance procedures provided in

this manual. Failure to do so may seriously impair

instrument performance. Repair or alteration of the

ZGARD S & DS gas sensors, beyond the scope of

these maintenance instructions or by anyone other

than authorized MSA service personnel, could cause

the product to fail to perform as designed, and

persons who rely on this product for their safety could

sustain serious personal injury or death.

6. The ZGARD S & DS gas sensors must be installed,

located and operated in accordance to all applicable

codes. These codes include, but are not limited to, the

National Fire Prevention Code and National Electric

Code.

7. Do not exceed the relay contact ratings listed in this

manual. Otherwise, the relay operation may fail, which

can result in personal injury or death.

FAILURE TO COMPLY WITH THE ABOVE WARNINGS

CAN RESULT IN SERIOUS PERSONAL INJURY OR

DEATH.

AVERTISSEMENT

1. Le détecteur d’émanations ZGARD S & DS tel que

représenté dans ce manuel doit être installé, opéré et

maintenu conformément aux étiquettes, les cautions,

avertissements, ainsi que les instructions et les

restrictions spécifiées.

2. Le détecteur d’émanations ZGARD S & DS ne doit pas

être fixé en plein air ou dans une région où des

concentrations explosives de gaz ou de vapeur sont

présentes dans l’atmosphère; Classe 1, Groupes A, B, C,

et D comme définis pas le NEC. Étant donné que les

détecteurs d’émanations ne sont pas protégés contre les

explosions, ils devraient être localisé dans un endroit

non-dangereux. Le détecteur d’émanation ZGARD S &

DS ne doit pas être exposé au soleil.

3. Veuillez ne pas peinturer le ZGARD S & DS. Nettoyer

uniquement avec de l’eau tiède, sans savon ou produits

de nettoyage.

4. Pour vérifier que l’appareil fonctionne bien, il s’agit de

l’exposer à une concentration d’émanation pour laquelle

l’appareil a été calibré. Conséquemment, une vérification

du calibre doit être incluse comme partie de l’installation

ainsi qu’à l’inspection régulière du système.

5. Un mot de caution lors de l’entretien de cet appareil; il est

nécessaire d’utiliser que les pièces MSA lors d’effectuer

l’entretien de cet appareil. Sinon, l’appareil peut faillir.

Toutes réparations ou modifications du détecteur

d’émanations au dessus des instructions ciincluses, ou

par autre personne non-autorisée par le MSA peut

causer une faillite mettant en danger les personnes qui

dépendent sur cet appareil pour leur bien-être contre les

blessures et la mortalité.

6. Le détecteur d’émanations ZGARD S & DS doit être fixé,

localisé, et opéré conformément aux codes applicable.

Ces codes sont inclus, mais pas limités au ‘National Fire

Prevention Code’ et le ‘National Electric Code.’

7. Ne pas dépasser l’indique du relais tel que spécifié dans

ce manuel d’instructions. Autrement, l’opération du relais

peut faire faillite qui, par la suite peut causer des

blessures physiques ou même la mortalité.

SI VOUS N’ADHÉRÉ PAS AUX AVERTISSEMENTS CI-

HAUT SPÉCIF BLESSURES CORPORELLES GRAVES

OU MORTELLES PEUVENT RESULTER

Table of Contents

Section 1,

General Information and Applications . . . . . . . . . . . . . . . . . . . . . . . .1-1

Table 1-1. ZGARD S & DS Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Section 2,

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Section 3,

Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Table 3-1. ZGARD S & DS Sensor Specifications . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Network Features and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Table 3-2 Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Table 3-3 BAUD Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Table 3-4 Network Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Table 3-4 Digital Binary Address Codes . . . . . . . . . . . . . . . . . . . . . . . . .3-2

Network Setup – BACnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Network Setup – MODBUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Section 4,

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Calibration Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Calibration Of ZGARD S & DS Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Zero Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Span Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Sensor Out of Range or Inoperative After Calibration . . . . . . . . . . . . . . . . . . . . . . .4-2

Sensor Fail Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Section 5,

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Table 5-1. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

WARNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Appendix A,

Installation Outline Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Section 1,

General Information and Applications

The ZGARD S Sensors are designed to detect the

presence of Carbon Monoxide, Nitrogen Dioxide and

Combustibles in air.

The ZGARD DS is a Dual Sensor in one enclosure

designed to detect the presence of Carbon Monoxide and

Nitrogen Dioxide in air.

Depending on the type of sensor used, electrochemical or

catalytic bead technology is employed. Each generates a

representative output signal proportional to the calibrated

operating range.

The ZGARD S & DS sensors offer a number of built-in

communications protocols that connect via an RS-485

multi-drop trunk to a master controller. The ZGARD S &

DS RS-485 version is specifically designed to operate

with any MSA ZGARD C 485 or CXII Controller, operating

as a system.

TABLE 1-1 shows distinctive features of the ZGARD S &

DS Sensors and is a quick guide for determining the

operating features of each sensor. The performance of

any ZGARD S & DS Sensor depends on the appropriate

and strategic placement within a guarded area. Gas

sensors should be strategically placed closest to the

areas where the target gases or vapors might occur in the

atmosphere.

Table 1-1. ZGARD S & DS Sensors

Carbon

Monoxide (EC)

Nitrogen

Dioxide (EC)

Combustible

(LEL)

Principal of Operation

Electrochemical

Catalytic Bead

Accuracy at STP

+/- 5% Full Scale

+/- 10% Full Scale

+/- 5% Full Scale

Operating Range

0-100 ppm

0-200 ppm

0-10 ppm

0-100% LEL

Zero Deadband

1 ppm

0.1 ppm

1% LEL

Operating Temperature

-20° to 40°C

0° to 40°C

-20° to 40°C

Storage Temperature

-20° to 50°C

-10° to 50°C

-20° to 50°C

Humidity

0 to 95% RH

Altitude

0-6526ft / 0-2000m

Sensor Enclosure

ZGARD Enclosure

Powder-coated metal double-gang connection box

Dimensions

5.5” H (140mm) x 5.5” W (140mm) x 2.2 D (56mm)

Weight

0.45kg (1.00 lbs.)

ZGARD DS Enclosure

Polycarbonate

Dimensions

7.0” H (178mm) x 10.5” W (267mm) x 4.5” D (114mm)

Weight

1.1kg (2.45 lbs.)

1-1

Section 2,

Installation Guidelines

NOTE: Reference the Installation Outline Drawings in this

manual, Appendix A.

Mounting

 Do not mount the sensor to structures subject to

vibration and shock, such as piping and piping

supports.

 Do not locate the sensor near an excessive heat

source or in wet or damp locations.

 For proper cooling, allow at least five inches of

clearance around all surfaces except for the

mounting surface. Also consider mounting the sensor

so it can be easily accessed for service and routine

testing.

 The sensor has four mounting lugs; securely mount

the instrument to a wall or support using appropriate

hardware.

Wiring Connections

Before putting a ZGARD S & DS Sensor into operation,

determine the elevation and the number of gas sensors

according to the required application. Also refer to the

ZGARD S & DS sensor(s) Installation Outline drawings

for important information regarding:

 Operating power

 Required conductors and wire size

 RS485 Network wiring

WARNING

When wiring the sensor, disconnect the

main power to prevent bodily harm.

AVERTISSEMENT

Lors de l’installation électrique du

détecteur, couper le courant d’électricité du

détecteur en entier pour éviter toutes

possibilités de chocs qui peut causer des

blessures corporelles.

CAUTION

Do not use the sensor power when

connecting any external devices.

Use shielded cable for wiring installation. Do

not install low voltage signal cable in the

same conduit as the other devices such as

sensors operating power and or relay wiring.

Make sure that each RS485 sensor is given a

unique address (Switch selected) to enable

the MSA ZGARD C series controller to

communicate properly.

When connecting sensors, make sure all

wiring is correct for the power and signal

leads. Ensure the RS485 bus wiring is not

interchanged; otherwise, permanent sensor

damage may result.

Perform all wiring and conduit installation in

accordance with the National Electrical

Code.

Failure to follow the above Warning and

Cautions can result in injury or property

damage.

CAUTION

Utilisez pas le pouvoir électrique du

détecteur pour brancher autres appareils.

Se servir uniquement le fil conducteur

électrique ayant un écran de protection.

Soyez avisé qu’il faut isoler un conduit

uniquement pour l’électricité (pouvoir) du

détecteur ainsi que le relais.

Assurez-vous que chaque détecteur a son

propre bouton de contrôle pour assurer que

le contrôleur du MSA ZGARD S & DS

communique directement tel que branché.

Lorsque vous branchez le détecteur isolé,

assurez-vous que le branchage de fils

électriques sont convenable au pouvoir

(électricité). Veuillez noter que le fil RS 485

ne doit pas être échangé pour un autre fil

électrique, il est unique à cet appareil.

Autrement, vus courez le risque

d’endommager, en permanence, le

détecteur.

Exécuter tout branchement et installation de

conduit conformément au “National Electric

Code”. A coup sûr, si les cautions ci-haut

mentionnés ne sont pas suivis, il y a

possibilité de blessures corporelles et vous

courez chance d’endommager votre

propriété.

2-1

Section 3,

Start-Up

 The ZGARD S and DS Sensors are factory-calibrated and ready for immediate use.

 Once power is applied to the unit and a 30-second delay occurs, the normal green LED is solid ON to

indicate the sensor is operating properly.

Table 3-1. ZGARD S & DS Sensor Specifications

Operating Power

24VDC or

24VAC 50/60Hz

Class 2 Source

250 mA max Comb

100 mA max EC

Signal

RS-485

2-wire (plus shield) network

connection

Network Features and Configuration

 All network communication uses 8N1 serial framing (8 data bits, no parity, 1 stop bit) regardless of

protocol or BAUD rate. The serial framing cannot be changed.

Table 3-2. Configuration Switches

SW1-1 through SW2-2 are used to represent a value using

the binary number system. This value is used as an address

or ID numbers. Any switch that is in the ON position adds its

Binary Value to the sum of all switches. Switches in the OFF

position add ‘0’.

SW2-3 is used to select whether the above value is used as

a MAC address or Device ID* (for BACnet protocol only).

The Device ID* has an offset of 291000*. The above value

is then added to the Device ID* offset for the final value. For

MODBUS protocol this switch has no meaning.

SW2-4 & SW2-5 are used to select the BAUD Rate for

MODBUS and BACnet. See Table 3-3.

SW2-6 through SW2-8 are used to select the

communications Protocol for the sensor. See Table 3-4

* If Device ID is set via SW1 & SW2. See 4.

Table 3-3. BAUD Rate Table 3-4. Network Protocol

SW2-4

SW2-5

BAUD Rate

OFF

9600

OFF

19200

OFF

38400

57600

3-1

SWx

No.

Binary

Value

Function

BACnet MAC (Range = 1-127)

SW1

BACnet Device ID (Range = 291000-291999)

MODBUS Address (Range = 1-127)

128

256

512

MAC or Device ID (BACnet only)

SW2

Baud Rate

Protocol

SW2-6

SW2-7

SW2-8

Protocol

OFF

BACnet

OFF

MODBUS RTU

OFF

MODBUS ASCII

OFF

ZGard Proprietary

OFF

Apogee P1 (Siemens)

ZGARD S & DS Sensors

Binary Value Switch Settings

Table 3-5. A representation of switch settings for values 0 through 48

3-2

Value

SW1-1

SW1-2

SW1-3

SW1-4

SW1-5

SW1-6

SW1-7

OFF

ZGARD S & DS Sensors

Network Setup

BACnet

Sensors connected to a BACnet network must have the

following parameters set properly in order to communicate with

the BACnet controller:

 Protocol selection set to BACnet (see Table 3-4)

 BAUD Rate (see Table 3-3)

 MAC Address (1-127)

 Device ID (291000 to 291999 if set by SW1 & SW2,

unrestricted if set by BACnet)

1. Select BACnet protocol on protocol selection switches

SW2-6 through SW2-8 as indicated in Table 3-4.

2. Select BAUD Rate of ZGARD sensor to match that of the

port on the BACnet controller that the sensor is connected to

using SW2-4 & SW2-5 as indicated in Table 3-3.

3. Slide SW2-3 to the ON position. This allows the MAC

address of the sensor to be selected. Choose a MAC

address for this sensor that is not yet used by another

device on the RS-485 bus of this sensor. Set switches SW1-

1 through SW2-2 to reflect the value for the MAC address.

4. Device ID may be set via SW1 & SW2 or via BACnet.

a. By factory default, Device ID is settable via SW1 & SW2.

Slide SW2-3 to the OFF position. Now Device ID may

be set using switches SW1-1 through SW2-2. Choose a

Device ID for this sensor that is not yet used by another

device on the BACnet controller. Set switches SW1-1

through SW2-2 to reflect the value for the Device ID.

Leave SW2-3 in the OFF position. Device ID is limited to

be within the range of 291000 to 291999.

b. Device ID may also be set via BACnet using any BACnet

object browser or the BACnet controller itself. Once

Device ID is changed using BACnet, SW1 & SW2

become disabled for setting Device ID regardless of

SW2-3 setting. To re-enable SW1 & SW2 Device ID

setting, follow 4.a. to set Device ID to 291999. Now

Device ID may be set using SW1 & SW2 again.

5. The sensor is now ready to be discovered using the discover

function on a BACnet controller.

6. Repeat steps 1. through 5. for all sensors making sure that

each sensor is assigned a unique MAC address on each RS-

485 bus and that each sensor is assigned a unique Device

ID system-wide.

Sensors configured for and connected to a BACnet Network

have the following BACnet Objects available for exchange with

the BACnet controller.

Object Name

Object Type

Description

Sensor-BAC

Device ID

Sensor CO

Analog Input

Gas value (Actual)

Sensor Range

Analog Value

Full Scale Sensor Range

Caution Level

Analog Value

Caution Level (Typical)

Warning Level

Analog Value

Warning Level (Typical)

Alarm Level

Analog Value

Alarm Level (Typical)

Alarm State

multiStateValue

Sensor Status

0-OK

1-Caution

2-Warning

3-Alarm

4-Fail

GasID

multiStateValue

1-99

Actual Object Name is dependent on sensor type

Typical (suggested) setpoint levels for sensor, not actual

setpoint levels, may be different than the setpoint(s) a

controller uses

3-3

ZGARD S & DS Sensors

Network Setup

MODBUS RTU & ASCII

Sensors connected to a MODBUS network must have the

following parameters set properly in order to communicate with

the MODBUS controller:

 Protocol selection set to MODBUS RTU or MODBUS

ASCII (see Table 3-4)

 BAUD Rate (see Table 3-3)

 MODBUS Address (1-127)

1. Select MODBUS RTU or MODBUS ASCII on protocol

selection switches SW2-6 through SW2-8 as indicated in

Table 3-4. The type of MODBUS selected depends on the

MODBUS controller.

2. Select BAUD Rate of ZGARD sensor to match that of the

port on the MODBUS controller that the sensor is

connected to using SW2-4 & SW2-5 as indicated in Table

3-3.

3. Set switches SW1-1 through SW2-2 to reflect the value for

the MODBUS address.

4. The sensor is now ready to be addressed from a MODBUS

controller.

5. Repeat steps 1. through 4. for all sensors making sure that

each sensor is assigned a unique address on each RS-485

bus that sensors are connected to.

Sensors configured for and connected to a MODBUS Network

have the following Registers available for exchange with the

MODBUS controller.

Description

Value Range

40000

Sensor Address

1-99

40001

Status

0-OK

1-Caution

2-Warning

3-Alarm

4-Fail

40002

Reserved

40003

Reserved

40004

Full Scale Sensor Range

0-65535

40005

Gas value (Actual)

0-65535

40006

Caution Level (Typical)

0-65535

40007

Warning Level (Typical)

0-65535

40008

Alarm Level (Typical)

0-65535

40009

Reserved

Actual Value Range is dependent on sensor type

Typical (suggested) setpoint levels for sensor, not actual

setpoint levels, may be different than the setpoint(s) a

controller uses

3-4

Section 4,

Calibration

Calibration Procedure

While the ZGARD S & DS sensors are factory

calibrated, the user must perform regular calibration

checks as part of a routine inspection and

maintenance schedule. Use calibration gases of

known and certified concentrations, and check the

expiration date on the gas cylinders.

WARNING

The calibration procedure must be

completed after the replacement of

sensing cells; otherwise the unit could

fail to perform as designed and per-

sons who rely on this product for their

safety could sustain severe personal

injury or death.

ATTENTION

Le procès de calibration doit être com-

plete lors du remplacement de cellules

du détecteur. Sinon, l’appareil peut faire

faillite qui augmente la possibilité de

causer des blessures corporels ou la

mortalité.

Calibration Equipment

 Flow Controller 0.25 liters/minute and tubing

 Zero Gas and Span Gas

Table 4-1. Calibration Equipment

SENSOR TYPE

SPAN VALUE

MSA GAS CYLINDER

PART NO.

Carbon Monoxide

60 ppm CO

710882

Nitrogen Dioxide

5 ppm NO

710332

Combustible

2.5% CH

100280032

Zero Air

20.8% O

Nitrogen

10028042

 Calibration Magnet (MSA p/n 30060-2)

 Calibration Cover for S Sensor (MSA p/n 10128624)

 Calibration Cover for DS Sensor (MSA p/n 10149017)

WARNING

Remove the Calibration Cover after

calibration is complete; otherwise, the

unit could fail to perform as designed

and persons who rely on this product

for their safety could sustain severe

personal injury or death.

ATTENTION

Enlever le couvercle du calibre seule-

ment une fois le procès de calibration

est terminé. Autrement, vous courez

chance de faillite de l’appareil et les

gens qui se fient sur cet appareil pour

leurs sécurité cours une chance de

blessures corporelles ou même la

mortalité.

Calibration of ZGARD S & DS Sensors

NOTE: Slow Flash = 1 Flash per second

Fast Flash = 8 Flashes per second

Zero Calibration

1. Apply Zero Air to sensor using calibration cover.

2. Apply magnet to calibration target until the

Green LED slow flashes; then, remove magnet.

3. Remove Zero Air when green LED is SOLID

ON (stops flashing)

NOTE: If the previous Span Calibration failed,

the red LED SLOW FLASH appears instead of

the green SOLID ON LED. Proceed to Span

Calibration.

4. Zero calibration is now complete (time required

is two minutes); proceed to Span Calibration.

Span Calibration

1. Apply Span Gas to sensor using calibration

cover.

2. Apply magnet to calibration target until the

Green LED fast flashes; then, remove magnet.

NOTE: Green LED slow flashes first.

3. Remove the Span Gas when the Green LED is

Solid ON.

4. Span calibration is now complete (time required

is two minutes).

 There is a two-minute delay when the

Green LED stays ON.

4-1

5. Remove calibration cover.

NOTE: Upon completion of span calibration,

there is a two-minute delay before sensor

output returns. This time allows for the span

gas to dissipate, preventing false indications

from the controller.

• If magnet is left on for more than 16

seconds, calibration aborts and normal

operation resumes (with no change to

calibration).

Sensor Out of Range or Inoperative

After Calibration

 If Sensor is out of range or inoperative after

calibration, the Red LED slow flashes.

 Perform a new Zero and Span calibration to

resolve the problem.

Sensor Fail Indication

 If a sensor fails or is not present, the Red LED

turns ON and the sensor is not seen by the

controller. (SENSOR FAIL)

4-2

Section 5,

Parts List

Table 5-1. Parts List

ITEM

PART NUMBER

Replacement Electrochemical (EC) CO Cell Assembly

10064004

Replacement Electrochemical (EC) NO

Cell Assembly

10064003

Replacement LEL Cell Assembly

10143928

Calibration Cover for S Sensor

10148624

Calibration Cover for DS Sensor

10149017

Calibration Magnet

30060-2

NOTE: When ordering replacements parts, please state the unit’s MSA Part Number and Serial Number

WARNING

Use only genuine MSA replacement

parts when performing any

maintenance on the ZGARD S & DS

Sensors. Failure to do so may seriously

impair instrument performance. Repair

or alteration of the ZGARD S & DS gas

sensors, beyond the scope of these

maintenance instructions or by anyone

other than authorized MSA service

personnel, could cause the product to

fail to perform as designed, and

persons who rely on this product for

their safety could sustain serious

personal injury or death.

Disconnect all power source(s) to the

ZGARD S & DS Sensors before

removing or changing components.

ATTENTION!

Un mot de caution lors de l’entretien du

détecteur ZGARD S & DS. Il est

nécessaire d’utiliser que les pieces

MSA lors d’effectuer l’entretien. Sinon,

vous pouvez causer l’appareil de ne

pas fonctionner proprement. Toutes

réparations ou modifications du

détecteur ZGARD S & DS au dessus

des instructions ci-incluses ou par

autre personne non-autorisée par le

MSA peut causer une faillite de

l’appareil mettant en danger les

personnes qui dépendent sur cet

appareil pour leur bien-être contre les

blessures et la

mortalité.

Coupez tout pouvoir (électricité) au

détecteur ZGARD S & DS avant

d’effectuer des changements,

modifications ou réparations.

5-1

Appendix A,

Installation Outline Drawings

MSA Z-Gard® DS MPO Dual Gas Sensor Le manuel du propriétaire

Marque: MSA

Modèle: Z-Gard® DS MPO Dual Gas Sensor

Taper: Le manuel du propriétaire

Ce manuel convient également à

Z-Gard® S MPO Single Gas Sensor

Télécharger le PDF

rapport

dans d''autres langues

English: MSA Z-Gard® DS MPO Dual Gas Sensor Owner's manual

MSA Z-Gard® DS MPO Dual Gas Sensor Le manuel du propriétaire

Ce manuel convient également à

MSA Z-Gard® DS MPO Dual Gas Sensor Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents