Ryobi RYI2200 Mode d'emploi

Marque: Ryobi

Modèle: RYI2200

Catégorie: Groupes électrogènes

Taper: Mode d'emploi

Ce manuel convient également à

RYi2200A

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

DIGITAL INVERTER GENERATOR

GÉNÉRATEUR NUMÉRIQUE D’INVERSEUR

GENERADOR DEL INVERSOR DE DIGITACES

RYi2200

To register your Ryobi product, please visit:

http://register.ryobitools.com/

Pour enregistrer votre produit de Ryobi, s’il vous plaît la visite:

http://register.ryobitools.com/

Para registrar su producto de Ryobi, por favor visita:

http://register.ryobitools.com/

NEUTRAL FLOATING

FLOTTANTE NEUTRE / NEUTRAL DE FLOTACIÓN

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% ethanol)

in this product. It is a violation of fed-

eral law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

Ce générateur a été conçu et fabriqué conformément à nos

strictes normes de fiabilité, de simplicité d’emploi et de sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’utiliser ce produit. Si tous

les avertissements et toutes les consignes de sécurités et

instructions du manuel d’utilisation ne sont pas bien compris,

ne pas utiliser ce produit.

Su generador ha sido diseñado y fabricado de conformidad

con estrictas normas para brindar fiabilidad, facilidad de uso y

seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido y eficiente funcionamiento

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador

antes de usar este producto. Si no comprende los avisos de

advertencia y las instrucciones del manual del operador, no

utilice este producto.

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this

product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

2 — English

TABLE OF CONTENTS

INTRODUCTION

 Introduction ......................................................................................................................................................................2

 Important Safety Instructions ........................................................................................................................................3-4

 Specific Safety Rules ........................................................................................................................................................4

 Symbols ......................................................................................................................................................................... 5-7

 Electrical ........................................................................................................................................................................7-9

 Features ...................................................................................................................................................................... 9-10

 Assembly ........................................................................................................................................................................ 11

 Operation ................................................................................................................................................................... 12-14

 Maintenance ..............................................................................................................................................................15-16

 Troubleshooting ..............................................................................................................................................................17

 Warranty ....................................................................................................................................................................18-20

 Parts Ordering / Service ....................................................................................................................................Back Page

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be

properly grounded. The nut and ground terminal on the frame must

always be used to connect the generator to a suitable ground

source. The ground path should be made with #8 size wire. Con-

nect the terminal of the ground wire between the lock washer and

the nut, and tighten the nut fully. Connect the other end of the

wire securely to a suitable ground source.

The National Electric Code contains several practical ways in

which to establish a good ground source. If a steel or iron rod is

used, it should be at least 5/8 in. diameter, and if a nonferrous

rod is used, it should be at least 1/2 in. diameter and be listed as

material for grounding. Drive the rod or pipe to a depth of 8 ft. If

a rock bottom is encountered less than 4 ft. down, bury the rod

or pipe in a trench.

All electrical tools and appliances operated from this generator

must be properly grounded by use of a third wire or be “Double

Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

WARNING:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground ter-

minal, consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or or-

dinances that apply to the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions for this product

that should be followed during installation and maintenance

of the generator.

Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

Do not allow children or untrained individuals to use this

unit.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

Keep all bystanders, children, and pets at least 10 feet

away.

Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

Do not touch bare wire or receptacles.

Do not use generator with electrical cords which are worn,

frayed, bare, or otherwise damaged.

Before storing, allow the engine to cool and drain fuel

from the unit.

Do not operate or store the generator in rain, snow, or

wet weather.

Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

Empty fuel tank, turn the engine/choke lever to the off

position and restrain the unit from moving before trans-

porting in a vehicle.

Allow engine to cool for five minutes before refueling.

To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

Do not smoke while handling fuel.

Store fuel in a container approved for gasoline.

Position the unit on level ground, stop engine, and allow

to cool before refueling.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Tighten the fuel cap securely after refueling.

Wipe spilled fuel from the unit.

Never attempt to burn off spilled fuel under any circum-

stances.

Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

4 — English

IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

Do not use this generator to provide power for emergency

medical equipment or life support devices.

Exhaust contains poisonous carbon monoxide, a color-

less, odorless gas. Breathing exhaust can cause loss

of consciousness and can lead to death. If running in a

confined or partially-enclosed area, the air may contain

a dangerous amount of carbon monoxide. To keep ex-

haust fumes from building up, always provide adequate

ventilation.

Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.

Place the generator on a flat, stable surface with a slope

of no more than 4°.

Operate outdoors in a well-ventilated, well-lit area isolated

from working areas to avoid noise interference.

Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.

Keep the generator a minimum of 3 feet away from all

types of combustible material.

Do not operate generator near hazardous material.

Do not operate generator at a gas or natural gas filling

station.

Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.

This generator has a neutral floating condition. This means

the neutral conductor is not electrically connected to the

frame of the machine.

Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.

Do not smoke when filling the generator with gasoline.

Shut down the engine and allow to cool completely before

adding gasoline or lubricant to the generator.

Do not remove the oil dipstick or the fuel tank cap when

the engine is running.

Pay close attention to all safety labels located on the

generator.

Keep children a minimum of 10 feet away from the gen-

erator at all times.

The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.

Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings.



For outdoor use only.





Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of shock or

injury.

Maintain the unit per maintenance instructions in this

Operator’s Manual.

Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion

Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any hot

surface.

Lifting Hazard

To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground

Consult with local electrician to determine grounding requirements

before operation.

Electrocution

Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

SAFETY LABELS

The information below can be found on the generator. For your safety,

please study and understand all of the labels before starting the generator.

If any of the labels come off the unit or become hard to read, contact an

authorized service center for replacement.

You WILL be KILLED or SERIOUSLY HURT if you do not follow the

Operator’s Manual instructions.

Risk of Fire. Do not add fuel while the product is operating.

Generator is a potential source of electric shock. Do not expose to

moisture, rain, or snow. Do not operate with wet hands or feet.

Exhaust contains poisonous carbon monoxide gas that can cause

unconsciousness or DEATH. Operate in well-ventilated, outdoor areas away

from open windows or doors.

Failure to properly ground generator can result in electrocution, especially if the

generator is equipped with a wheel kit.

Do not expose to rain or use in damp locations.

Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains

carbon monoxide. This is a poison you cannot see or smell.

NEVER use inside a home or garage, EVEN IF doors and windows are open.

Only use OUTSIDE and far away from windows, doors, and vents.

Do not use E85 fuel.

7 — English

SYMBOLS

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below

the top of the fuel neck. Stop the en-

gine for five minutes before refueling to

avoid the heat from the muffler igniting

fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first operating the generator. Always

check the lubricant level before each operation. The lubricant

level should always register between the hatched areas on the

dipstick. The unit is equipped with a sensor which will automati-

cally shut off the engine if the lubricant level falls below a safe limit.

GROUNDING WARNING

National Electric Code requires generator to be grounded to an approved earth ground.

HOT SURFACE WARNING

Do not touch the muffler or aluminum

cylinder of the engine. They are very HOT

and will cause severe burns. Don’t put

any flammable or combustible materials

in the direct path of the exhaust.

Product does not include ground rod or copper wire. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an electrician for local grounding requirements.

Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Le code electrique americain (National

Electric Code) requiert un générateur pour une bonne mise à la terre approuvée. Appeler un électricien

pour connaître les exigences locales de mise à la terre.

El producto no incluye el alambre de cobre ni la barra de conexión a tierra. Los Reglamentos Nacionales

de Electricidad exigen que el generador esté debidamente conectado a una tierra aprobada.

Comuniquese con un electrista para todo lo relacionado con los requistos de conexión a tierra.

WARNING

ADVERTENCIA

AVERTISSEMENT

940513008-02

Risk of Fire. Check for any fuel overflow or leaking. Stop the engine before refueling.

DANGER PELIGRO

Risque d’incendie. Vérifier l'absence de débordement ou de fuite de carburant.

Arrêter le moteur avant de fair le plein.

Riesgo de incendio. Revise si hay algún derrame o fuga de combustible. Apague el

motor antes de poner combustible.

940974007-03

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can damage the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

ELECTRICAL

8 — English

ELECTRICAL

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Tool or Appliance

Running

Watts*

Additional

Starting Watts*

Refrigerator 700 1350

Portable Fan 40 120

Laptop 250 250

46 in. Flat Panel

Television

190 190

Light (75 Watts) 75 75

1255 Total

Running Watts

1350 Highest

Starting Watts

Total Running Watts 1255

Highest Starting Watts + 1350

Total Starting Watts Needed 2605

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts

Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450

950

1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

NOTICE:

Operating voltage and frequency requirement of all electronic equipment should be checked prior to plugging them

into this generator. Damage may result if the equipment is not designed to operate within a +/- 10% voltage variation,

and +/- 3 hz frequency variation from the generator name plate ratings. To avoid damage, always have an additional

load plugged into the generator if solid state equipment (such as a television set) is used. A power line conditioner is

recommended for some solid state applications.

9 — English

ELECTRICAL

FEATURES

Application/Equipment

Estimated

Starting

Watts*

Estimated*

Additional

Starting

Watts

Emergency / Home Standby

Lights (qty. 4 x 75 W) 300 300

Refrigerator 700 1350

46 in. Flat Panel Television 190 190

Satelite Receiver 250 250

Portable Fan 40 120

Heater 1300 1300

Laptop 250 250

Slow Cooker 270 270

Radio 50 50

Job Site

ElectricDrill−3/8in. 600 1000

Quartz Halogen Work Light 1000 1000

Reciprocating Saw 960 1920

CircularSaw−7-1/4in. 1400 2300

MiterSaw−10in. 1800 1800

AirCompressor−1/4HP 970 1600

AirlessSprayer−1/3HP 600 1200

*Wattages listed are approximate. Check tool or appliance for actual wattage.

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

PRODUCT SPECIFICATIONS

ENGINE

Engine Type .........................Single Overhead Cam (SOHC)

Spark Plug .......................................................... LD A7RTC

Engine Lubricant Volume.......................................13.52 oz.

GENERATOR

Rated Voltage .........................................120 V AC/12 V DC

Rated Amps .............................................15 A AC/7.5 A DC

Rated Running Watts .............................................1,800 W

Starting Watts .........................................................2,200 W

Rated Frequency ........................................................ 60 Hz

10 — English

FEATURES

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

120 V AC RECEPTACLES

Your generator has two single phase, 60 Hz outlets that are

120 Volt AC, 20 Amp receptacles. These can be used for

operating appropriate appliances, electrical lighting, tools,

and motor loads.

AIR FILTERS

The air filters help to limit the amount of dirt and dust drawn

into the unit during operation.

AUTO IDLE SWITCH

The auto idle switch is used to control the speed of the

engine and conserve fuel. When the switch is in the ON (I)

position and no appliances are connected to the unit, the

engine will idle. If an appliance is added, the engine speed

will increase to power the item. If the appliance is removed,

the engine will return to idle.

BATTERY CHARGING CABLE

The battery charging cable makes it easy to charge 12 Volt

lead acid batteries with the generator.

NOTE: Only use battery charging cable to charge vented

wet lead acid batteries.

CARRY HANDLES

The generator is equipped with two carry handles for easy

transport. Both handles should be used to carry the gen-

erator.

DC CIRCUIT BREAKER

The circuit breaker is provided to protect the generator

against electrical overload.

DC RECEPTACLE

Your generator has a 12 volt, 7.5 Amp DC receptacle for

charging lead acid batteries.

ENGINE/CHOKE LEVER

The engine/choke lever is used when starting, stopping, and

running the engine.

WARNING:

The 12 V DC receptacle is designed to charge vented

wet lead acid batteries only. Other types of batteries may

burst, causing personal injury and damage.

FUEL TANK

The fuel tank has a capacity of 1.0 gallon.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

LED DISPLAY

LEDs provide feedback to indicate whether the generator is

in use, overloaded, or in need of lubricant.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

PARALLEL KIT TERMINALS

The non-polarized parallel kit terminals are used with a

parallel kit (sold separately) that will allow generators to be

linked together to increase output.

NOTE: Read and understand the parallel kit’s instructions

prior to use. Kit is for usage with this unit only.

RESET BUTTON

The reset button is used to restore power if an overload

occurs. To restore power, depress the reset button.

RETRACTABLE HANDLE

The generator is equipped with a retractable handle that can

be adjusted for storage and transportation.

STARTER GRIP AND ROPE

The starter grip and rope is used (along with the engine/

choke lever) to start the generator’s engine.

11 — English

UNPACKING

This product has been shipped completely assembled.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Generator

Battery Charging Cable

Engine Lubricant (SAE 10W 30)

Screwdriver

Funnel

Operator’s Manual

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

12 — English

OPERATION

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or smell.

If you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages,

crawlspaces, or other partly enclosed areas. Deadly

levels of carbon monoxide can build up in these

areas. Using a fan or opening windows and doors

does NOT supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in

electrocution, especially if the generator is equipped with

a wheel kit. National Electric Code requires generator to

be properly grounded to an approved earth ground. Call

an electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

 Only use OUTSIDE and far away from windows, doors,

and vents.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

In some areas, generators are required to be registered

with local utility companies.

If the generator is used at a construction site, there may

be additional regulations which must be observed.

LED DISPLAY

See Figure 2.

Power:

The power indicator will light when the generator is on and

the receptacles are operational.

NOTE: If the generator is overloaded, the power indicator

light will go off.

Overload:

The overload indicator will light if the generator’s wattage/

amperage capacity is exceeded. To reset the generator, re-

move all loads from the generator and press the reset button

(see fig. 1). Add loads back to the generator one at a time

being careful not to exceed the generators wattage rating.

Lubricant:

The oil indicator will light and the engine will automatically

shut off whenever the lubricant level in the engine becomes

low. The engine may not be restarted until sufficient engine

lubricant has been added to the generator.

NOTE: It is normal for the indicator lights to illuminate and/

or blink each time the engine is started. Once the engine

warms up, the lights should default to the pattern above.

CHECKING/ADDING LUBRICANT

See Figure 3.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

13 — English

OPERATION

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

 Loosen the screws at the side of the engine cover.

Remove cover and set aside.

 Unscrew the oil cap/dipstick and remove.

 Wipe dipstick clean and re-seat in hole; do not re-thread.

 Remove dipstick again and check lubricant level.

Lubricant level should fall between the minimum and

maximum marks on the dipstick.

 If level is low, add engine lubricant until the fluid level

rises between the minimum and maximum marks on the

dipstick.

 Replace and secure the oil cap/dipstick.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being added

to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

 Replace and secure the fuel tank cap.

 Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

CHECKING/ADDING FUEL

See Figure 4.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

When adding gas to the generator, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the

generator cool before adding gas. ALWAYS fill the fuel tank

outdoors with the machine turned off.

 Remove the fuel cap.

 Fill the fuel tank to 1 in. below the top of the fuel neck.

 Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

STARTING THE ENGINE

See Figures 5 - 7.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

NOTICE:

Do not place the generator directly on the ground when

using the unit in grassy areas or in areas with dense

vegetation. Doing so could result in grass discoloration

and/or localized soil damage.

 Unplug all loads from the generator.

 Place the auto idle switch in the off position.

 Slide the engine/choke lever to the start (center) position.

NOTE: When the engine/choke lever is in the start

(center) position, the fuel will flow from the fuel tank to

the engine. If engine is warm, move the engine/choke

lever right to the run (restart) position.

 Pull the starter grip and rope until the engine runs

(a maximum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place. Initial starting of the

unit may require additional pulls to prime the fuel pump.

 Allow the engine to run for 15-30 seconds, then move

the engine/choke lever right to the run position.

14 — English

OPERATION

STOPPING THE ENGINE

See Figures 5 - 6.

 Remove any load from the generator.

 Place the engine/choke lever in the off position.

To stop the engine in an emergency situation:

 Put the engine/choke lever in the off position.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases may be hot enough to cause serious burns and /

or ignite combustible objects.

USING THE BATTERY CHARGING CABLE

See Figure 8.

WARNING:

The 12 V DC receptacle is designed to charge vented

wet lead acid batteries only. Other types of batteries may

burst, causing personal injury and damage.

NOTICE:

The 12 V DC receptacle provides continuous charge. Do

not overcharge battery or leave battery unattended. Doing

so may cause damage to the battery.

NOTICE:

Do not use the generator to jump start vehicles. Doing

so could result in damage to the vehicle or it’s electrical

components.

 Using the battery clamps, connect the battery charging

cable assembly to the battery terminal. Connect the

red wire to the positive (+) terminal first, then connect

the black wire to the negative (–) terminal. Make sure all

connections are secure.

NOTE: Be careful not to short across the terminals when

installing. Shorting the terminals together can cause

sparks, damage to the battery or generator, or even burns

or explosions.

 Connect the battery charging cable assembly to the

12 V DC receptacle.

 Start the generator.

NOTE: The AC receptacles can be used while the DC

receptacle is in use.

 The battery will become slightly warm to the touch while

charging. This is normal and does not indicate a problem.

NOTE: Only use battery charging cable assembly to

charge vented wet lead acid batteries.

 When batteries become fully charged, disconnect

the battery charging cable assembly from the battery.

Disconnect the negative (black) wire first, then the positive

(red) wire, being careful not to short across the terminals.

Always abide by the safety warnings provided with the

battery.

NOTE: Most batteries will be completely charged after

30 to 120 minutes. However, it is highly recommended

that you refer to your battery manufacturer’s instructions

for specific charge times.

 Unplug battery charging cable assembly and store for

later use.

MOVING THE GENERATOR

See Figure 9.

 Place the auto idle switch in the off position. At the off

position, the fuel valve will be closed and prevent any gas

flow.

 Allow 30 minutes of “cool down” time before storing the

machine.

 Pull the retractable handle out.

 Facing the front of the generator, grasp the folding handle

firmly with one hand.

 Lift the generator toward you until it balances on the

wheels.

 Turn around and pull the unit along behind you to the

desired location.

 Lower the generator until it sits securely on a flat surface.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation.

Please contact your authorized service center for important

information regarding these modifications. Operating this

engine without the proper altitude modification may increase

the engine’s emissions and decrease fuel economy and

performance.

15 — English

MAINTENANCE

 Tilt the generator to the side and allow lubricant to drain

from the oil fill hole into an approved container.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

 Return the generator to an upright position and refill with

lubricant following the instructions in the Checking/

Adding Lubricant section previously in this manual.

For amount of lubricant needed to refill, see Product

Specifications earlier in this manual or the accompanying

engine manual, if applicable.

 Replace and secure the oil cap/dipstick.

 Reinstall the engine cover. Replace the screw and tighten

securely.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local retailer for more information.

SPARK PLUG REPLACEMENT

See Figure 13.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cover.

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using spark plug wrench.

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced. For replacement

spark plug, see Product Specifications earlier in this

manual or the accompanying engine manual, if applicable.

 Measurepluggap.Thecorrectgapis0.024−0.028in.

(0.60-0.70 mm). To widen gap, if necessary, carefully

bend the ground (top) electrode. To lessen gap, gently

tap ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water

entering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp cloth.

CHECKING/CLEANING AIR FILTER

See Figures 10 - 11.

For proper performance and long life, keep air filter clean.

 Loosen the screws on the side of the engine cover.

Remove cover and set aside.

 Loosen the screw in the center of the air filter cover and

turn the cover 1/4 turn clockwise, pulling the cover down

and off the unit. Remove air filter cover and set aside.

 Remove both the large and the small air filters.

 Wash the air filters with warm, soapy water. Rinse and

squeeze to dry.

 Reinstall the air filters.

NOTE: Make sure the filters are seated properly inside

the generator. Installing the filters incorrectly will allow

dirt to enter the engine, causing rapid engine wear.

 Reinstall the air filter cover. Tighten screw to secure.

 Reinstall the engine cover. Tighten screws to secure.

CHANGING ENGINE LUBRICANT

See Figure 12.

For best performance, engine lubricant should be changed

after every 100 hours or 6 months of operation.

 Loosen the screw at the top of the engine cover. Remove

cover and set aside.

 Remove the oil fill cap/dipstick.

16 — English

MAINTENANCE

DRAINING FUEL TANK/CARBURETOR

See Figures 14 - 15.

To help prevent gum deposits in the fuel system, drain the

fuel from the tank and carburetor before storing.

DRAINING THE FUEL TANK:

NOTICE:

Remove all lubricant from the unit before draining the fuel

tank. Failure to do so could cause damage to the unit.

 Remove the fuel cap.

 Tilt the generator and allow fuel to drain from the fuel tank

into an approved container.

 When the fuel has drained from the tank, replace the fuel

cap.

DRAINING THE CARBURETOR:

 Loosen the screws at the top of the engine cover. Remove

cover and set aside.

 Place the engine/choke lever in the run position.

 Position a suitable container under the carburetor drain

screw to catch fuel; loosen the screw.

 Allow fuel to drain completely into container.

 Retighten drain screw securely.

 Place the engine/choke lever in the off position.

NOTE: Consult hazardous waste management guidelines in

your area for the proper way to dispose of used fuel.

TRANSPORTING

 Place the engine/choke lever in the off position.

 Make sure engine and exhaust of unit is cool.

 Keep unit level to prevent fuel spillage.

 Do not drop or strike unit or place under heavy objects.

MAINTENANCE SCHEDULE

NOTE: If a separate engine manual is provided for this generator, please follow the maintenance schedule provided in the engine

manual instead of the maintenance information listed below.

Before

each use

After 1st month

or 20 hours of

operation

Every 3 months

or 50 hours of

operation

Every 6 months

or 100 hours

of operation

Every year or

after 300 hours

of operation

Check Engine Lubricant



Change Engine Lubricant

 

Check Air Filter



Clean Air Filter



Change Air Filter



Check/Adjust Spark Plug



Replace Spark Plug



Check/Adjust Idle Speed



Check/Adjust Valve

Clearance

1,2



Clean Fuel Tank and Filter

1,2



Check Fuel Hose

 

Fuel Filter Inspect Replace

Check All Hose

Connections

 

Inspect Fuel Tank Vapor

Vent (If Equipped)

 

Inspect Carbon Canister

(CARB Models Only)

 

1. These items should only be carried out by an authorized service center.

2. See engine manual for maintenance schedule for this item.

NOTE: Maintenance should be performed more frequently when generator is used in dusty areas.

When generator has exceeded the maximum figures specified in the table, maintenance should still be cycled according

to the intervals of time or hours stated herein.

17 — English

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start. Engine/choke lever is in run position.

No fuel.

Stale gasoline or water in gasoline.

Lubricant level is low.

Spark plug faulty, fouled, or improperly

gapped.

Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Dirty fuel filter.

Move engine/choke lever to start position.

Fill fuel tank.

Drain entire system and refill with fresh

fuel.

Check engine lubricant level and fill, if

necessary.

Replace spark plug.

Drain fuel and carburetor. Refuel with

fresh gasoline.

Replace fuel filter or contact authorized

service center or contact authorized

service center.

Engine lacks power. Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Dirty air filter.

Drain fuel and carburetor. Refuel with

fresh gasoline. If problem continues,

contact your nearest authorized service

center.

Clean or replace as needed.

DC receptacle does not work. Circuit protector engaged

Item plugged in is defective.

Remove any load from the generator.

Turn the auto idle switch to off, then

depress the DC circuit breaker.

Try a different item.

AC receptacle does not work. Item plugged in is defective. Try a different item.

Generator stops. Generator is overloaded. Remove loads and press the reset

button.

If problem persists after trying the above solutions, contact your nearest authorized service center for assistance.

The following symptoms may indicate problems that will affect the emissions level of the unit:

Hard starting or stalling after starting

Rough idle

Misfiring or backfiring under load

Afterburning (backfiring)

Black exhaust smoke or high fuel consumption

If you encounter any of these symptoms, have the unit inspected and repaired by the nearest authorized service center.

18 — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board, United Sates Environmental Protection

Agency (EPA), and Zhejiang ZhongJian Technology Co., Ltd. are pleased

to explain the emissions control system warranty on your 2012 small off-

road engine (SORE). In California, new SOREs must be designed, built

and equipped to meet the State’s stringent anti-smog standards. Zhejiang

ZhongJian Technology Co., Ltd. must warrant the emissions control system

on your SOREs for the periods of time listed below provided there has been

no abuse, neglect or improper maintenance of your SOREs.

Your emission control system may include parts such as the carburetor,

fuel tanks, fuel caps, fuel lines, the ignition system, and catalytic converter.

Also included may be hoses, belts, clamps, connectors and other emission-

related assemblies.

Where a warrantable condition exists, Zhejiang ZhongJian Technology

Co., Ltd. will repair your small off-road engine at no cost to you including

diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The emissions control system is warranted for two years. If any emissions-

related part on your engine is defective, the part will be repaired or replaced

by Zhejiang ZhongJian Technology Co., Ltd.

OWNER’S WARRANTY RESPONSIBILITIES:

 As the SORE owner, you are responsible for the performance of the

required maintenance listed in your owner’s manual. Zhejiang ZhongJian

Technology Co., Ltd. recommends that you retain all receipts covering

maintenance on your SORE, but Zhejiang ZhongJian Technology Co.,

Ltd. can not deny warranty solely for the lack of receipts or for your

failure to ensure the performance of all scheduled maintenance.

 As the SORE owner, you should however be aware that Zhejiang

ZhongJian Technology Co., Ltd. may deny your warranty coverage if your

SORE or a part has failed due to abuse, neglect, improper maintenance

or unapproved modifications.

 You are responsible for presenting your SORE to distribution center

or service center authorized by Zhejiang ZhongJian Technology Co.,

Ltd. as soon as the problem exists. The warranty repairs should be

completed in a reasonable amount of time, not to exceed 30 days.

 If you have any questions regarding your warranty coverage, you should

contact Zhejiang ZhongJian Technology Co., Ltd. customer service

representative at 1-866-340-3912.

DEFECTS WARRANTY COVERAGE

Adopted by the Air Resources Board, Zhejiang ZhongJian Technology Co.,

Ltd. warrants to the ultimate purchaser and each subsequent purchaser that

the small off-road engine (SORE) (1) has been designed, built and equipped

so as to conform with all applicable regulations; and (2) is free from defects

in materials and workmanship that cause the failure of a warranted part

to conform with those regulations as may be applicable to the terms and

conditions stated below.

(A) The warranty period begins on the date the engine is delivered to an

ultimate purchaser. The warranty period is two years.

(B) Subject to certain conditions and exclusions as stated below, the

warranty on emissions related parts is as follows:

(1) Any warranted part that is not scheduled for replacement as required

maintenance in your Owner’s Manual is warranted for the warranty

period stated above. If the part fails during the period of warranty

coverage, the part will be repaired or replaced by Zhejiang ZhongJian

Technology Co., Ltd. according to Subsection (4) below. Any such

part repaired or replaced under warranty will be warranted for the

remainder of the period.

(2) Any warranted part that is scheduled only for regular inspection in

your Owner’s Manual is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be

warranted for the remaining warranty period.

(3) Any warranted part that is scheduled for replacement as required

maintenance in your Owner’s Manual is warranted for the period

of time before the first scheduled replacement date for that part. If

the part fails before the first scheduled replacement, the part will

be repaired or replaced by Zhejiang ZhongJian Technology Co.,

Ltd. according to Subsection (4) below. Any such part repaired or

replaced under warranty will be warranted for the remainder of the

period prior to the first scheduled replacement point for the part.

(4) Repair or replacement of any warranted part under the warranty

provisions herein must be performed at a warranty station at no

charge to the owner.

(5) Notwithstanding the provisions herein, warranty services or repair

will be provided at all of our distribution centers that are franchised

to service the subject engines.

(6) The engine owner must not be charged for diagnostic labor that

leads to the determination that a warranted part is in fact defective,

provided that such diagnostic work is performed at a warranty

station.

(7) Zhejiang ZhongJian Technology Co., Ltd. is liable for damages to

other engine components proximately caused by a failure under

warranty of any warranted part.

(8) Throughout the engine warranty period stated above, Zhejiang

ZhongJian Technology Co., Ltd. will maintain a supply of warranted

parts sufficient to meet the expected demand for such parts.

(9) Any replacement part may be used in the performance of any

warranty maintenance or repairs and must be provided without

charge to the owner. Such use will not reduce the warranty

obligations of Zhejiang ZhongJian Technology Co., Ltd.

(10) Add-on or modified parts that are not exempted by the Air Resources

Board may not be used. The use of any non-exempted add-on

or modified parts by the ultimate purchaser will be grounds for

disallowing a warranty claims. Zhejiang ZhongJian Technology

Co., Ltd. will not be liable to warrant failures of warranted parts

caused by the use of a non-exempted add-on or modified part.

(11) The manufacturer issuing the warranty shall provide any documents

that describe that manufacturer’s warranty procedures or policies

within five working days of request by the Air Resources Board.

EMISSION WARRANTY PARTS LIST

The repair or replacement of any warranted part otherwise eligible for

warranty coverage may be excluded from such warranty coverage if

Zhejiang ZhongJian Technology Co., Ltd. demonstrates that the engine has

been abused, neglected, or improperly maintained, and that such abuse,

neglect, or improper maintenance was the direct cause of the need for

repair or replacement of the part. That notwithstanding, any adjustment of a

component that has a factory installed, and properly operating, adjustment

limiting device is still eligible for warranty coverage. The following emissions

warranty parts for each engine family list is covered.

For engine family CZJTS.1061CA :

(1) Fuel Metering System:

(a) Gasoline carburetor assembly and its internal components

(b) Carburetor gaskets

(d) Fuel Line

(e) Fuel Line Fittings

(f) Clamps

(2) Air Induction System including:

(a) Intake pipe/manifold

(b) Air cleaner

(3) Ignition System including:

(a) Spark plug

(b) Ignition coil

(4) Catalytic Muffler Assembly (if so equipped) including:

(a) Muffler gasket

(b) Exhaust manifold

(5) Crankcase Breather Assembly including:

(a) Breather connection tube.

(6) Fuel tank evaporative emissions control system including:

(a) Purge Valves

(b) Carbon Canister

(d) Fuel Cap

(e) Fuel Tank

(7) Miscellaneous items Used in Above Systems including:

(a) Switches

(b) Hoses, belts, connectors, and assemblies.

(8) Air injection system

(a) Pulse valve

CALIFORNIA AND EPA EMISSIONS CONTROL WARRANTY STATEMENT

19 — English

WARRANTY

Techtronic Industries North America, Inc. (herein

“Techtronic Industries”), warrants that each new engine

sold by it will be free, under normal use and service,

from defects in material and workmanship for a period

listed below from the date of sale to the original retail

purchaser. Techtronic Industries obligation under this

Limited Warranty shall be limited to the repair and

replacement, at Techtronic Industries option, of any part or

parts which upon examination is/are found, in Techtronic

Industries judgment, to have been defective in material or

workmanship. It shall be a condition of Techtronic Industries

obligation under this Limited Warranty that Techtronic

Industries, directly or through one of its Distributors or

Service Centers authorized to service the particular engine

involved, receive prompt notice of any warranty claim

and that the engine or the part or parts claimed to be

defective be promptly delivered, transportation prepaid,

to such Distributor or Service Center for inspection and

repair. All repairs qualifying under this Limited Warranty

must be performed by Techtronic Industries or one of its

authorized Distributors or Service Centers.

WARRANTY PERIODS:

158F Gasoline Engine (Private/Residential) Limited 2

year Warranty

158F Gasoline Engines (Commercial) Limited 90 Day

Warranty

The repair or replacement of any part or parts under this

Limited Warranty shall not extend the term of the engine

warranty beyond the original term as set forth above.

LIMITATIONS AND EXCLUSIONS: This Limited Warranty

shall not apply to:

1. Repair required because of prolonged storage including

damage caused by old or contaminated fuel in the fuel

tank, fuel lines, or carburetor, sticky valves or corrosion

and rust of engine parts.

2. Repair required due to overheating. (Most often caused

by overloaded or clogged or damaged or missing flywheel,

fan, inlet air passages, cooling fins, or air shrouds.)

3. Dirt or grit related wear caused by improper air cleaner

maintenance (most often resulting in worn piston, piston

LIMITED ENGINE WARRANTY

rings, cylinders, valves, valve guides, carburetor, or other

internal components).

4. Broken or scored parts caused by low oil level, dirty,

or improper grade of oil.

5. Engine tune-ups and normal maintenance service

including, but not limited to, valve adjustment, normal

replacement of service items, fuel, and lubricating oil, etc.

6. Any engine which has been subject to negligence,

misuse, accident, misapplication, or overspeeding.

7. Any engine that has been installed, repaired, or altered

by anyone in a manner which in Techtronic Industries sole

judgment adversely affects its performance or reliability.

8. Any engine which has been fitted with or repaired with

parts or components not manufactured or approved by

Techtronic Industries which in Techtronic Industries’ sole

judgment adversely affects its performance or reliability.

9. Instances when normal use has exhausted the life of

a component or an engine.

The customer is responsible for all transportation charges

in connection with any warranty work.

Techtronic Industries reserves the right to modify, alter,

or improve any engines or parts without incurring any

obligation to modify or replace any engine or parts

previously sold without such modification, alternation,

or improvement.

No person is authorized to give any other warranty or to

assume any additional obligation on Techtronic Industries’

behalf unless made in writing and signed by an officer of

Techtronic Industries.

THIS WARRANTY, TECHTRONIC INDUSTRIES

OBLIGATION HERE UNDER, ARE IN LIEU OF ANY

OTHER WARRANTIES OR OBLIGATIONS OF ANY

KIND, EXPRESSED OR IMPLIED, INCLUDING ANY

WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. THERE ARE NO

WARRANTIES WHICH EXTEND BEYOND THE

DESCRIPTION ON THE FACE HERE-OF. TECHTRONIC

INDUSTRIES SHALL IN NO EVENT BE LIABLE FOR

ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES.

IF YOU HAVE ANY QUESTIONS REGARDING YOUR WARRANTY RIGHTS AND RESPONSIBILITIES, CONTACT

YOUR NEAREST AUTHORIZED RYOBI SERVICE CENTER AT 1-800-860-4050.

La page est en cours de chargement...

Ryobi RYI2200 Mode d'emploi

Marque: Ryobi

Modèle: RYI2200

Catégorie: Groupes électrogènes

Taper: Mode d'emploi

Ce manuel convient également à

RYi2200A

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RYI2200 User guide
español: Ryobi RYI2200 Guía del usuario

Ryobi RYI2200 Mode d'emploi

Ce manuel convient également à

Ryobi RYI2200 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents