VTech VH6210 Manuel utilisateur

VH6210

Convertible Ofﬁce

Wireless Headset

VH6211

Convertible Ofﬁce

Wireless Headset

with Lifter

Abridged user’s manual

BC

Go to businessphones.vtech.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Congratulations

on your purchase of this VTech product. Before using this product,

please read the Important safety information.

This Abridged user’s manual provides you with the basic installation and

use instructions. A limited set of features are described in abbreviated

form.

Visit businessphones.vtech.com/support/downloads to download a

full set of installation and operation instructions for:

• Headset connection methods

“Option 1: Connect to IP phone via EHS”

“Option 2: Connect to traditional corded phone”

“Option 3: Connect to traditional corded phone with Lifter”

“Option 4: Connect to a computer”

• Headset wearing styles

“Over-the-ear hook”

“Over-the-head band”

“Behind-the-neck band”

• The software application

“Software application - Installation and Operation Guide”

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, please

dial 1 (800) 267-7377.

T

Compatible with

Hearing

Ai

d T-Coil

TIA-1083

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of the

Telecommunications Industry Association. Used under license.

The VH6210/VH6211 includes a wireless headset and base that allow

you to have handsfree phone conversations.

The package also comes with the EHS (Electronic hookswitch) cables

and headset audio cable that allow you to connect your headset

using either one or both of the following methods:

• PHONE mode - Connect to a deskphone

If you want to connect your headset to a deskphone, you can

simply use the cables provided to connect the headset to a

deskphone directly.

• PC mode - Connect to a computer

Use the USB cable to connect the headset base and your PC. You

can make and receive VoIP calls through Skype® or Skype for

Business®, using

the software application

.

VH6211 Convertible Office Wireless Headset with Lifter:

The VH6211 package also comes with the extra corded handset lifter,

making it convenient to answer and end calls right from the headset,

so that the product can be used in different ways depending on your

needs.

For lifter’s information, refer to the section Lifter.

Introduction

Skype® and Skype for Business® are registered trademarks of Microsoft Corporation.

Batteries with battery

compartment cover

Wireless headset

Behind-the-neck band

Four over-the-ear

hooks

Sponge cover

for ear hooks

Four earbuds

Over-the-head band

Two spare rubber

rings for headset

earpiece

What’s in the box

Your product package contains the following items. Save your sales

receipt and original packaging in the event warranty service is

necessary.

Abridged user's manual

For VH6210/VH6211:

USB cable

Abridged user’s manual

Headset base

power adapter

Corded phone

connection cable

Headset base

What’s in the box

Headset audio cable

EHS cable 1

EHS cable 2

Auxiliary ring detectorCorded handset lifter

For VH6211 only:

For VH6210/VH6211 (con’t):

Table of contents

Overview

Headset ..........................................1

Headset base .................................2

Install headset battery ................. 4

Power up the headset base ........5

Charge the headset battery ........5

Charge and store your spare

battery ........................................ 6

Connection methods ....................7

PHONE mode ............................7

PC mode .....................................7

Option 1: Connect to

IP phone via EHS ...................... 8

Option 2: Connect to a

traditional corded phone

(for VH6211 only) ...................... 9

Option 3: Connect to a

traditional corded phone

with Lifter (for VH6211 only) ... 9

Option 4: Connect to a

computer ................................... 9

Position the headset .................. 10

Over-the-ear hook ................. 10

Over-the-head band ..............13

Over-the-neck-band ..............15

Before use

Headset operation ......................17

Headset power on/off ............17

PHONE mode and

PC mode ...................................17

Operate

PHONE mode ............................. 18

Operate with IP phone

via EHS...................................... 18

Operate with traditional

corded phone ........................... 19

Operate with traditional

corded phone via Lifter ......... 19

PC mode ...................................... 20

Call settings ..................................21

Auto Answer .............................21

Change Audio Bandwidth .....21

Adjust the headset earpiece

audio .......................................... 22

Headset ringer .........................23

Anti-Startle (G616) ...................23

Temporary ringer silencing ... 24

Volume control ....................... 24

Mute .......................................... 24

Hot-swappable headset

battery replacement ...............25

Lifter (for VH6211 only)

Overview ...................................... 27

Connect the Lifter ...................... 29

Operate with Lifter ..................... 29

Appendix

Adding and registering

a new headset .........................30

Headset lights .............................. 31

Headset alert tones .................32

Headset alert prompts ............ 32

Headset base lights ....................33

Frequently asked questions ..... 34

Maintenance ...............................40

Important safety information ... 41

Safety information .................. 41

Especially about wireless

headsets ................................... 42

Precautions for users of

implanted cardiac

pacemakers ............................. 43

For C-UL compliance ................. 44

Mesures de sécurité

importantes .............................44

FCC Part 68 and ACTA ...............48

FCC Part 15 ..................................50

California Energy Commission

battery charging testing

instructions................................51

Limited warranty .........................52

Disclaimer and Limitation of

Liability ..................................... 55

Technical speciﬁcations ............. 56

1

Headset

Overview

1 –VOL+/VOL-

• Slide the volume switch to the right or left to adjust the headset ringer volume

while in idle mode, or the listening volume while on a call.

2 – ON/OFF button and LED light

• Press to make, answer or end a call.

• See page 31 for lights behavior.

3 – MUTE

• Mute the microphone during a call.

4 – Battery with cover attached

• The battery is permanently attached to the battery compartment cover and they

are inseparable from each other. Remove the entire assembled unit to replace

the battery.

5 – Microphone

1

2

3

4

5

2

Overview

Headset base

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

1 – VOLUME / MICROPHONE

• Press to adjust the speaking volume while on a call.

2 – Magnetic charging mount

• Place the headset here for charging.

3 – MUTE/SPARE BATT (light)

• See page 33 for lights behavior.

4 – PHONE (mode button and light)

• Press to enter the PHONE mode. See page 33 for lights behavior.

5 – PC (mode button and light)

• Press to enter the PC mode. See page 33 for lights behavior.

6 – PAIR

• Press to initiate headset registration or deregistration.

7 – Spare battery compartment cover

8 – POWER jack (green dot)

9 – PHONE jack (blue dot)

10 – EHS jack (red dot)

11 – (USB port)

• Open the port cover to plug in the USB cable for use with PC mode.

12 – LIFTER jack (for VH6211 only)

3

Overview

7

8

1

9

13

14

15

12

10

11

2

3

4

6

5

13 – AutoAns ON/OFF

• When turned on, your headset will then automatically answer a call when it is

lifted from the charging cradle.

14 – Audio Adjustment Switch

• When you have connected the headset base to a deskphone, use this switch to

adjust the headset earpiece audio between A and F, until the dial tone is clear.

Notes

• The default setting of the Audio Adjustment Switch is A.

• The audio adjustment setting is dependent on

- the types of deskphones to which the headset base is connected; and

- the interference caused by other DECT systems operating in the same

environment.

15 – WB (Wideband) / NB (Narrowband) Switch

• Use this switch to adjust the audio bandwidth. Wideband audio delivers wider

frequency response and higher HD audio quality.

Headset base

4

Getting started

Install headset battery

CAUTION

• Do not disassemble the battery from its battery compartment cover.

Notes

• You will hear the voice prompt "Low battery" when you press the ON/OFF

button while the headset battery is low.

• When fully charged, the headset battery supports up to 5 hours of talk time or 48

hours of standby time.

• If you slide the WB / NB (wideband/narrowband) switch to WB for enhanced

audio quality, the power consumption will also be increased, thereby resulting in

reduced talk time (see page 21).

• To order a replacement battery pack (model BT291865), visit our website at

businessphones.vtech.com or call 1 (800) 595-9511. In Canada, dial

1 (800) 267-7377.

1. Align the metallic contacts between the battery and the battery

compartment, and then place the battery down.

2. Slide the battery until it clicks into place.

3. Charge it for at least 30 minutes.

5

Getting started

Charge the headset battery

Hang the headset onto the magnetic charging mount.

The magnet holds the headset in place.

• The light will turn:

- steady red when the headset

battery is low while charging;

- steady purple when the battery

is well charged; and

- steady blue when the battery

is fully charged.

Note

• For optimal performance, charge the headset battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

headset is not in use, recharge by hanging it onto the headset base.

Power up the headset base

1. Plug the small end of the headset

base power adapter labelled

to the POWER jack (green dot) at

the rear of the headset base.

2. Plug the large end into an electrical

outlet not controlled by a wall

switch.

6

Getting started

Charge and store your spare battery

The spare battery is for powering on the headset. You can install it into

your headset base for charging and storage purposes.

The headset supports hot swapping, in which the current call on the

headset will remain connected if you replace the battery within 5

minutes. You can even have an unlimited talk time with timely battery

replacement.

1. Align the metallic contacts between the battery and the battery

compartment, and then place the battery down.

2. Slide the battery until it clicks into place.

• The MUTE | SPARE BATT light turns green when charging.

3. Slide the battery compartment cover back to the headset base.

Note

• For optimal performance, charge the spare battery for at least 30 minutes before

use. The battery is fully charged after 2 hours of continuous charging. When the

spare headset is not to be used, keep it in charging in the headset base.

7

Getting started

Connection methods

Choose one of the following methods to connect your headset for

operation in either PHONE mode or PC mode.

PHONE mode

Option 1: Connect to IP phone via EHS

• You can connect the headset to an IP phone using the EHS

cable and headset audio cable provided. The headset acts as

a supplementary device that can join calls. Use the IP phone

connected to make or answer calls.

Option 2: Connect to traditional corded phone (for VH6211 only)

• You can connect the headset to a traditional corded phone using

the corded phone connection cable provided. You need to

physically lift the corded handset off the corded phone base cradle

before you can use the headset to join in the call.

Option 3: Connect to traditional corded phone with

Lifter (for VH6211 only)

• You can connect the headset to a corded phone using the corded

phone connection cable and lifter provided (see page 29). The

headset acts as a supplementary device that can join calls. You can

simply press on the headset to use the connected corded phone

to make or answer calls.

PC mode

Option 4: Connection to a computer

• Connect the headset base to your PC with the USB cable provided.

You can make and receive VoIP calls through Skype or Skype for

Business, using

the software application

.

8

Getting started

Connection methods

Note

• The cords have colored labels that guide you to plug them into the correct headset

base jacks. The back of the headset base has color-coded dots and the names of the

jacks above them that correspond to the colored labels on the cords.

For detailed instructions of the four options to connect your

headset, visit the product page of VH6210 or VH6211 at

businessphones.vtech.com/support/downloads to download

the respective instructional document.

Option 1: Connect to IP phone via EHS

Connect the headset to an IP phone using the EHS cable and headset

audio cable provided. Depending on the brand and series of your

IP phone, you might need to use either EHS cable 1 or EHS cable 2

provided for connection.

Visit businessphones.vtech.com for the compatibility list of IP phone

models that are compatible for EHS connection, as well as the

respective EHS adapter(s) that you need to purchase separately.

Connect with EHS cable 1 Connect with EHS cable 2

EHS cable 1 EHS cable 2

Headset

audio

cable

Headset

audio

cable

9

Getting started

Option 3: Connect to a traditional corded phone with Lifter

(for VH6211 only)

U

se the corded phone

connection cable and lifter

provided

to c

onnect the

headset to a traditional

corded phone.

Option 4: Connect to a computer

Use the USB cable provided

to connect the headset to your

computer. Your

headset supports calls through

Skype or

Skype for Business.

Install

the software application

before operating in PC mode.USB cable

Connection methods

Option 2: Connect to a traditional corded phone (for VH6211 only)

Use the

corded phone

connection cable

provided

to connect the headset to

a traditional corded phone.

Corded phone

connection cable

Corded phone

connection cable

10

Getting started

Position the headset

Over-the-ear hook

Attach the headset accessories and wear the headset:

1. Mount the earhooks over your ear and insert the earbuds to check

the best ﬁtting. Remove them from your ear after checking.

2. Insert your desired earhook to the headset.

• Rotate it until it securely holds in place.

Note

• If you accidentally ripped off the rubber ring, use a spare rubber ring to replace it.

Rubber ring

11

Getting started

Position the headset

3. Insert your desired earbud to the headset.

• Make sure the protruding bump is pointing towards your

mouth when placed on your ear. The protruding bump on the

earbud holds the headset securely in your ear.

4. Hook the headset on your ear. Adjust the angle of the headset until

the microphone is pointing towards your mouth.

12

Getting started

Position the headset

Remove the earbud and earhook:

Remove the earbud and earhook, when you need to replace them

in the Over-the-ear hook, when you need to change to the

over-the-head and behind-the-neck style.

1. Hold both sides of the earbud. Twist and pull the earbud until it

separates from the earpiece.

2. Rotate the earhook to vertical direction.

3. Pull the earhook until it separates from the headset.

To re-insert another set of earbud and earhook, refer to the previous

section.

13

Getting started

Position the headset

Over-the-head band

Attach the headband and wear the headset:

1. With the headset at a vertical angle (microphone pointing down),

insert the headset earpiece into the headband.

2. Rotate the headset to a horizontal direction until it holds into place.

Note

• If you accidentally ripped off the rubber ring, use a spare rubber ring to replace it.

Rubber ring

La page est en cours de chargement...

VTech VH6210 Manuel utilisateur

Ce manuel convient également à

VTech VH6210 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents