Simplicity MULT-LANGUAGE OPERATOR'S MANUAL-15.50 GROSS TORQUE, 29-INCH Manuel utilisateur
- Catégorie
- Souffleuses à neige
- Taper
- Manuel utilisateur
2
1741658
3
18
16
17
15
7
19
4
2
1
5
1
620
14
9
13
10
11 12
8
en
3
1740876
CONTENTS
HAZARD SYMBOLS AND THEIR MEANINGS 4. . . . . . . . . . . .
OPERATING SYMBOLS AND THEIR MEANINGS 4. . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE CHART 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE SHOOTING CHART 15. . . . . . . . . . . . . . . . . . . . . . . . .
1741658
WARRANTY 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Traction Drive Clutch Lever-- Used to propel snowthrower
forward or reverse. Push down to engage, release to
disengage.
en
4
1740876
:@ 8!
$
&
Explosion
Toxic fumes
Shock
Hot Surface
Fire
Operator’s Manual − Read and understand
before performing any activity or running
equipment.
Safety Alert − Identifies safety information about
hazards that can result in personal injury.
Rotating auger
Rotating impeller
Rotating gears
Thrown objects
Keep a safe distance
from the equipment.
Shut off engine and
remove spark plug
connector before
performing maintenance
or repair work.
Never reach into
rotating parts.
$ 8!
$
2
Stop
Fuel
Choke off
Oil
Choke on
Slow
Fast
On Off
Ignition Key
Ignition Off
Ignition On
Primer bulb
Throttle
Drive Clutch
Auger Clutch
Engage
RIGHT
Auger Collector
Traction
Discharge Chute
LEFT UP DOWN
Forward
Neutral
Reverse
Push to engage
electric start
Electric
Start
Engine
Start
Engine Run
Engine Off
Chute Deflector
Engage
Disengage
1741658
en
5
1740876
/
- &
•) $
•
$
•) $
• '
$ 3
•
$
/
• %
•% +" "
%
•%
+'(%
%
)
2 $
•- &
•)
•, #22
•'
$
$
+'(%
#/
)
•3 $
/
• )
/
•2& !
/
•
&
• / #22
•, #22
• #22 4
&
+'(%
+ "
3 "
•
•%
*'%((
1741658
en
6
1740876
* " "
2 "
*:( '++( .2
• #22 0
•2 5
•%
•
•' $
*:( 8&'%&( ((
•!
•%
•
• #6+)7-)
2
*:( $#%'&( A.#"(&
•%
*:( &%'(8#$%&( A.#"(&
• +!68
*:( 8&$%( '8$2( $% A.#"(& *&: .2 ( &'(
•
*'%((
1741658
en
77
1740876
RULES FOR SAFE OPERATION
WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety
rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe
personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text
signifies important cautions or warnings which must be followed.
Safe Operation Practices for Snowthrowers
IMPORTANT: Safety standards require operator presence controls
to minimize the risk of injury. Your snowthrower is equipped with
such controls. Do not attempt to defeat the function of the operator
presence control under any circumstances.
Training
1. Read, understand, and follow all instructions on the machine and in the
manuals before operating this unit. Be thoroughly familiar with the
controls and the proper use of the equipment. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the equipment. Never allow adults to
operate the equipment without proper instruction.
3. Keep the area of operation clear of all persons, particularly small
children and pets.
4. Exercise caution to avoid slipping or falling especially when operating in
reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to be used and
remove all doormats, sleds, boards, wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before starting the engine
(motor).
3. Do not operate the equipment without wearing adequate winter outer
garments. Wear footwear that will improve footing on slippery surfaces.
Avoid loose fitting clothing that can get caught in moving parts.
4. Handle fuel with care; it is highly flammable.
a. Use an approved fuel container.
b. Never add fuel to a running engine or hot engine.
c. Fill fuel tank outdoors with extreme care. Never fill fuel tank
indoors. Replace fuel cap securely and wipe up spilled fuel.
d. Never fill containers inside a vehicle or on a truck or trailer bed with
a plastic liner. Always place containers on the ground, away from
your vehicle, before filling.
e. When practical, remove gas−powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible, then refuel
such on a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
f. Keep nozzle in contact with the rim of the fuel tank or container
opening at all times, until refueling is complete. Do not use a nozzle
lock−open device.
g. Replace gasoline cap securely and wipe up spilled fuel.
h. If fuel is spilled on clothing, change clothing immediately.
5. Use extension cords and receptacles as specified by the manufacturer
for all units with electric drive motors or electric starting motors.
6. Adjust the collector housing height to clear gravel or crushed rock
surfaces.
7. Never attempt to make any adjustments while the engine (motor) is
running (except when specifically recommended by manufacturer).
8. Let engine (motor) and snowthrower adjust to outdoor temperatures
before starting to clear snow.
9. Always wear safety glasses or eye shields during operation or while
performing an adjustment or repair to protect eyes from foreign objects
that may be thrown from the machine.
10.Never operate the snowthrower without proper guards, plates or other
safety protective devices in place.
Operation
1. Do not put hands or feet near or under rotating parts. Keep clear of the
discharge opening at all times.
2. Exercise extreme caution when operating on or crossing gravel drives,
walks or roads. Stay alert for hidden hazards or traffic.
3. After striking a foreign object, stop the engine (motor), remove the wire
from the spark plug, disconnect the cord on electric motors, thoroughly
inspect snowthrower for any damage, and repair the damage before
restarting and operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the engine (motor) and
check immediately for the cause. Vibration is generally a warning of
trouble.
5. Stop the engine (motor) whenever you leave the operating position,
before unclogging the collector/impeller housing or discharge chute and
when making any repairs, adjustments, or inspections.
6. When cleaning, repairing, or inspecting, make certain the
collector/impeller and all moving parts have stopped. Disconnect the
spark plug wire and keep the wire away from the spark plug to prevent
accidental starting.
7. Do not run the engine indoors, except when starting the engine and for
transporting the snowthrower in or out of the building. Open the outside
doors; exhaust fumes are dangerous (containing CARBON
MONOXIDE, an ODORLESS and DEADLY GAS).
8. Exercise extreme caution when operating on slopes. Do not attempt to
clear steep slopes.
9. Never operate the snowthrower without proper guards, plates, or other
safety protective devices in place and working.
10.Never direct the discharge toward people or areas where property
damage can occur. Keep children and others away.
11.Do not overload the machine capacity by attempting to clear snow at too
fast a rate.
12.Never operate the machine at high transport speeds on slippery
surfaces. Look behind and use care when operating in reverse.
13.Disengage power to the collector/impeller when snowthrower is
transported or not in use.
14.Use only attachments and accessories approved by the manufacturer of
the snowthrower (such as cabs, tire chains, etc.).
15.Never operate the snowthrower without good visibility or light. Always be
sure of your footing and keep a firm hold on the handles. Walk, never
run.
16.Never touch a hot engine or muffler.
17.Never operate the snowthrower near glass enclosures, automobiles,
window wells, drop−offs, and the like without proper adjustment of the
snow discharge angle.
en
88
1740876
18.Never direct discharge at bystanders or allow anyone in front of the unit.
19.Never leave a running unit unattended. Always disengage the auger and
traction controls, stop engine, and remove keys.
20.Do not operate the unit while under the influence of alcohol or drugs.
21.Keep in mind the operator is responsible for accidents occurring to other
people or property.
22.Data indicates that operators, age 60 years and above, are involved in a
large percentage of power equipment−related injuries. These operators
should evaluate their ability to operate the unit safely enough to protect
themselves and others from injury.
23.DO NOT wear long scarves or loose clothing that could become
entangled in moving parts.
24. Snow can hide obstacles. Make sure to remove all obstacles from the
area to be cleared.
Children
Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the unit and the operating activity.
Never assume that children will remain where you last saw them.
1. Keep children out of the area and under the watchful care of another
responsible adult.
2. Be alert and turn off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners, shrubs, trees, or other
objects that may obscure vision.
Clearing A Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge chute is the
most common cause of injury associated with snowthrowers. Never use
your hand to clean out the discharge chute.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have stopped rotating.
3. Always use a clean out tool, not your hands.
Service, Maintenance And Storage
1. Check shear bolts (pins) and other bolts at frequent intervals for proper
tightness to be sure the equipment is in safe working condition.
2. Never store the machine with fuel in the tank inside a building where
ignition sources are present such as hot water and space heaters, or
clothes dryers. Allow the engine to cool before storing in any enclosure.
3. Always refer to operator’s manual for important details if the
snowthrower is to be stored for an extended period.
4. Maintain or replace safety and instruction labels as necessary.
5. Run the machine a few minutes after throwing snow to prevent
freeze−up of the collector/impeller.
6. If fuel is spilled, do not attempt to start the engine but move the machine
away from the area of spillage and avoid creating any source of ignition
until fuel vapors have dissipated.
7. Always observe safe refueling and fuel handling practices when
refueling the unit after transportation or storage.
8. Always follow the engine’s manual instructions for storage preparations
before storing the unit for both short and long term periods.
9. Always follow the engine manual instructions for proper start-up
procedures when returning the unit to service.
10.Keep nuts and bolts tight and keep equipment in good condition.
11.Never tamper with safety devices. Check their proper operation
regularly and make necessary repairs if they are not functioning
properly.
12.Components are subject to wear, damage, and deterioration. Frequently
check components and replace with manufacturer’s recommended
parts, when necessary.
13.Check control operation frequently. Adjust and service as required.
14.Use only factory authorized replacement parts when making repairs.
15.Always comply with factory specifications on all settings and
adjustments.
16.Only authorized service locations should be utilized for major service
and repair requirements.
17.Never attempt to make major repairs on this unit unless you have been
properly trained. Improper service procedures can result in hazardous
operation, equipment damage and voiding of manufacturer’s warranty.
Emissions
1. Engine exhaust from this product contains chemicals known, in certain
quantities, to cause cancer, birth defects, or reproductive harm.
2. If available, look for the relevant Emissions Durability Period and Air
Index information on the engine emissions label.
Ignition System
1. This spark ignition system complies with Canadian ICES-002.
919
1740876
ASSEMBLY
Read and follow the assembly and adjustment
instructions for your snow thrower. All fasteners
are in the parts bag. Do not discard any parts or
material until the unit is assembled.
WARNING: Before doing any
assembly or maintenance to the
snow thrower, remove the wire
from the spark plug.
NOTE: In this instruction book, left and right
describe the location of a part from the
operator’s position behind the unit.
NOTE: Torque is measured in foot pounds
(metric N.m). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.
NOTE: Fasteners and loose parts are shown
at full size in Figure 2 on page 32.
NOTE: Illustrations are located on page 2
and on pages 32 through 38.
Tools Required
1 Knife
1 Pliers
2 1/2 inch open end wrenches
2 9/16 inch open end wrenches
1 Measuring tape or ruler
1 Screwdriver
How To Remove The Snow Thrower
From The Carton
1. (Figure 3) The snow thrower is shown in the
shipping position.
2. Cut down all four corners of the carton and
lay the side panels flat or use pull tab to
remove box from base.
3. Cut and discard the plastic ties that secure
the crank assembly and the speed control
rod assembly.
4. Locate all parts that are packed separately
and remove from the carton.
5. Remove and discard the packing material
from around the snow thrower.
6. (Figure 1) For shipping purposes, the height
adjust skids (7) are attached to the pallet.
Remove the screw (17) that secures each
height adjust skid (7) to the pallet.
7. Hold onto the lower handle and pull the snow
thrower off the pallet.
CAUTION: DO NOT back over cables.
8. Remove the packing material from the
handle assembly.
9. Cut the ties that secure the clutch control
cables (1) to the lower handle (2). Move the
cables away from the motor frame.
How To Assemble The Handle And
Crank Assembly
1. (Figure 4) Loosen, but do not remove, the
fasteners (1) in the upper holes of the lower
handle.
2. Remove the fasteners and the crank
assembly eyebolt (11) from the lower holes
of the lower handle.
3. (Figure 1) Put the shift lever (6) into first
forward position.
4. (Figure 4) Raise the upper handle (2) to the
operating position.
NOTE: Make sure the cables are not
caught between the upper and lower
handle.
5. Install the fasteners and the crank assembly
eyebolt (11) that were removed in step 2.
DO NOT tighten until all fasteners are in
place.
6. (Figure 5) Attach the crank rod (15) to the
universal joint assembly (16) with the hair
pin (12).
7. (Figure 4) Tighten nut on eye bolt (11).
Make sure eye bolt (11) is properly aligned
and the crank (18) can freely rotate.
8. Tighten all handle fasteners.
How To Install The Speed Control Rod
1. (Figure 9) Attach the ball joint (6), located
on the bottom end of the speed control rod
(2), to the shift yoke assembly (7). The
fasteners (8) are attached to the ball joint
(6) at the factory.
The length of the ball joint (6) and speed
control rod (2) have been pre−adjusted at
the factory. If an adjustment is required,
loosen the nut (9). Remove the fasteners
(8) to disconnect the ball joint (6) from the
shift yoke assembly (7). To lengthen or
shorten the speed control rod (2), turn the
adapter (10) to obtain the correct length.
2. (Figure 12) Attach the handle (11) onto the
speed select lever (5). On some models the
handle (11) is attached. To lock in position,
tighten the hex jam nut (10) against the
bottom of the handle (11).
3. Make sure the speed select lever (5)
functions correctly. Move the speed select
lever (5) through all speeds.
How To Install The Knobs
NOTE: If knobs are already installed, go to
the next selection.
Remote Chute Knob (Figure 12)
1. Assemble remote chute knob (1) onto lever
(3) until snug against nut (2). On some
models the remote chute knob (1) is
attached.
2. Make sure lip (4) on the remote chute knob
(1) is pointed toward the engine.
3. Tighten the nut (2) against the bottom of the
remote chute knob (1).
Check The Cables
1. (Figure 8) Check the traction drive cable
(1) and the auger drive cable (2). If the
bottom of the cables have become
disconnected, reinstall the cables.
2. (Figure 10) If the top of the cables (5) have
become disconnected from the drive levers
(6), attach the cables (5) to the “Z” fitting
(7).
How To Set The Skid Height (Figure 1)
The snow thrower is equipped with height
adjustable skids (7) mounted on the outside of
the auger housing (4). To adjust the height of
the skids, see “How To Adjust The Height Of
The Skids” in the Maintenance section.
How To Set The Length Of The Cables
The cables were adjusted at the factory and no
adjustments should be necessary. However,
after the handles are put in the operating
position, the cables can be too tight or too loose.
If an adjustment is necessary, see “How To
Check And Adjust The Cables” in the Service
And Adjustment section.
How To Assemble The Drift Cutter
(if equipped)
Drift cutters are used to cut a path through snow
deeper than the auger housing.
1. (Figure 11) Loosen the wingnuts (2) that
secure the drift cutters (1) to the auger
housing.
2. Raise the drift cutters (1) to the desired
height.
3. Tighten the wingnuts (2).
How To Prepare The Engine
NOTE: The engine was shipped from the
factory filled with oil. Check the level of the
oil. Add oil as needed.
WARNING: Follow the engine
manufacturer’s instructions for the
type of fuel and oil to use. Always
use a safety fuel container. Do not smoke
when adding gasoline to the engine. When
inside an enclosure, do not fill with
gasoline. Before you add fuel, stop the
engine. Let the engine cool for several
minutes.
Check the oil. See the engine manufacturer’s
instructions for the type of fuel and oil to use.
Before you use the unit, read the information on
safety, operation, maintenance, and storage.
Important! Before You Start Operating
Check the fasteners. Make sure all
fasteners are tight.
On electric start models, the unit was
shipped with the starter cord plugged
into the engine. Before operating,
unplug the starter cord from the engine.
If a bar code label is attached to the
handle, remove before operating.
Snow Chute Assembly
1. Position the snow chute to the INSIDE of
the snow chute flange. Align the three
holes in the snow chute with holes in snow
chute flange (see Figure 6).
2. Place three 5/16-18 carriage bolts from the inside
of the chute as shown in Figure 6 (hardware
is found in parts bag).
3. Place three 5/16-18 flat washers and three
5/16-18 nuts on the outside of the flange.
4. First tighten the rear carriage bolt, then
tighten the remaining two carriage bolts.
Make sure all carriage
bolts are tight.
6. Attach the remote snow chute deflector cable
to the cable chute bracket Figure 7 and
secure by tightening nuts (on cable) to the
cable chute bracket.
5. Attach the remote snow chute deflector cable to
the weld stud (on deflector) and secure in
place using a pushnut as shown in
Figure 7 in hardware bag).
.
NOTE: Check all carriage bolts in flange for
tightness. DO NOT overtighten.
NOTE: Before starting step 6 make sure that
the chute deflector is in the full open position
and the remote chute lever is in the full open
position.
en
10
1740876
OPERATION
NOTE: Illustrations are located on page 2
and on pages 32 through 38.
CAUTION: Use only attachments and
accessories approved by the manufacturer
of the snow thrower (such as tire chains,
electric start kits, etc.).
Know Your Snow Thrower (Figure 1)
Read this Instruction Book and safety rules
before operation the snow thrower. Compare the
illustration with your snow thrower to familiarize
yourself with the location of various controls and
adjustments.
How To Control The Discharge Of The
Snow
WARNING: Never direct the
discharge of snow toward
bystanders.
WARNING: Always stop the engine
before unclogging the discharge
chute or the auger housing and
before leaving the snow thrower.
1. (Figure 1) Turn the crank assembly (2) to
change the discharge direction of the
snow.Turn the crank assembly (2) to
change the discharge direction of the snow.
2. Pull the remote chute lever (20) back to
discharge the snow high and far. Push the
remote chute lever (20) forward to
discharge the snow down.
How To Stop The Snow Thrower
(Figure 1)
1. To stop discharging snow, release the auger
drive lever (5).
2. To stop the wheels, release the traction
drive lever (1).
3. Stop the engine.
a. To stop the engine on models with a
throttle control (13), first move the
throttle control (13) to the SLOW
position and then move it to the STOP
position.
b. To stop the engine on models with an
ignition switch (13), move the ignition
switch (13) to the OFF position.
c. Pull out and remove the safety key (8).
CAUTION: To stop the engine, do not move
the choke control to CHOKE position.
Backfire or engine damage can occur.
How To Go Forward or Backward
(Figure 1)
1. To change the ground speed, first release the
traction drive lever (1) and then move the
speed shift lever (6) to the desired speed.
2. Ground speed is determined by snow
conditions. Select the speed by moving the
speed shift lever (6) into the appropriate
notch on the shift lever plate.
Speed 1, 2 Wet, Heavy
Speed 3 Light
Speed 4 Very Light
Speed 5, 6 Transport only
3. To go forward, engage the traction drive
lever (1). Maintain a firm hold on the handle
as the snow thrower starts to move forward.
Guide the snow thrower by moving the
handle either left or right. Do not attempt to
push the snow thrower.
4. To go backward, release the tractor drive
lever (1).
5. Move the speed shift lever (6) into either
first or second reverse.
6. Engage the traction drive lever (1).
IMPORTANT: Do not move the speed shift
lever (6) while the traction drive lever (1) is
engaged.
How To Throw Snow (Figure 1)
1. Engage the auger drive lever (5).
2. To stop throwing snow, release the auger
drive lever (5).
WARNING: The operation of any
snow thrower can result in foreign
objects being thrown into the eyes,
which can result in severe eye damage.
Always wear safety glasses or eye shields
while operating the snow thrower. We
recommend standard safety glasses or use
a wide vision safety mask over your
glasses.
Before Starting The Engine
1. Before you service or start the engine,
familiarize yourself with the snow thrower. Be
sure you understand the function and
location of all controls.
2. Check the tension of the clutch cable before
starting the engine. See “How To Adjust The
Clutch Cable” in the Maintenance section of
this manual.
3. Make sure that all fasteners are tight.
4. Make sure the height adjust skids are
properly adjusted. See “How To Adjust The
Height Of The Skids” in the Maintenance
section of this manual.
5. Check the air pressure in the tires. The
correct air pressure is 1 BAR (14 PSI) to 1,25
BAR (17 PSI). Do not exceed the maximum
amount of air pressure shown on the side of
the tire.
How To Stop The Engine (Figure 1)
1. To stop the engine on models with a throttle
control (13), first move the throttle control
(13) to the SLOW position and then move it
to the STOP position.
2. To stop the engine on models with an
ignition switch (13), move the ignition
switch (13) to the OFF position.
3. Pull out and remove the safety key (8).
CAUTION: To stop the engine, do not move
the choke control to CHOKE position.
Backfire or engine damage can occur.
How To Start The Engine (Figure 1)
Models equipped with an Electric Starter
NOTE: An electric starter kit can be added to
recoil start engines. Electric starter kits are
available from your nearest authorized
service center.
WARNING: The starter is equipped
with a three−wire power cord and
plug and is designed to operate on
A.C. household current. The power
cord must be properly grounded at all times
to avoid the possibility of electrical shock
which can injure the operator. Carefully
follow all instructions in the “How To Start
The Engine” section. Make sure that your
house wiring is a three−wire grounded
system. If you are not sure, ask a licensed
electrician. If your house wire system is not
a three−wire grounded system, do not use
this electric starter under any conditions. If
your system is grounded but a three−hole
grounded receptacle is not available to start
the engine, have a three−hole grounded
receptacle installed by a licensed
electrician. To connect a A.C. power
cord, always connect the power cord to the
switch box (11) on the engine first. Then,
plug the other end into the three−hole
grounded receptacle. When disconnecting
the power cord, always unplug the end from
the three−hole grounded receptacle first.
How To Start A Cold Engine (Figure 1)
1. Check the engine oil.
2. Fill the fuel tank with regular unleaded petrol.
See “How To Prepare The Engine”.
3. Make sure the traction drive lever (1) and
the auger drive lever (5) are in the
disengaged (released) position.
4. To start the engine on models with a throttle
control (13), move the throttle control (13)
to the FAST position. Operate the engine
with the throttle control (13) in the FAST
position.
5. To start the engine on models with an
ignition switch (13), move the ignition
switch (13) to the ON position.
6. Insert the safety key (8) into the ignition slot.
Make sure the safety key (8) snaps into
place. Do not turn the safety key (8).
Remove the extra safety key and keep in a
safe place.
7. Move the choke control (14) to the full
choke position.
8. (Electric Start) Connect the power cord to
the switch box (11) located on the engine.
9. (Electric Start) Plug the other end of the
power cord into a three−hole, grounded
A.C. receptacle. (See the WARNING
in this section).
10.Push the primer button (9). Every time you
push the primer button (9), wait two
seconds. For the number of times required to
push the primer button (9), see the engine
manufacturer’s instructions.
11. (Electric Start) Push on the electric start
button (10) until the engine starts. Do not
crank for more than 5 seconds at a time.
Wait one minute between starts to allow the
starter to cool.
12.(Recoil Start) Slowly pull the recoil starter
handle (12) until resistance is felt and then
pull rapidly to start the engine. Do not allow
the recoil starter handle (12) to snap back.
Slowly return the recoil starter handle (12).
13.If the engine does not start in 5 or 6 tries,
See the “Trouble Shooting Chart”
Instructions.
14.Allow the engine to warm up for several
minutes. As the engine warms up, adjust the
choke control (14) toward the RUN position.
Wait until the engine runs smoothly before
each choke adjustment.
3. To engage Free-HandTM control, BOTH levers
must be depressed. Free-Hand control
allows you to operate the other snowthrower
controls by releasing either the left or right
lever. Release both levers to disengage
Free-Hand control.
en
11
1740876
15.(Electric Start) First disconnect the power
cord from the three−hole receptacle. Then,
disconnect the power cord from the switch
box (11).
NOTE: In temperatures below 05F (−185C),
allow the engine to warm up for several
minutes before blowing snow.
16.When throwing snow, always run the engine
with the throttle control (13), if equipped, in
the fast position.
WARNING: Never run the engine
indoors or in enclosed, poorly
ventilated areas. Engine exhaust
contains carbon monoxide, an odorless
and deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts
located on the engine or the snow thrower.
The temperature of muffler and nearby
areas may exceed 150°F (665C). Avoid
these areas.
How To Start A Warm Engine (Figure 1)
If an engine has been running and is still warm,
leave the choke control (14) in the off position
and do not push the primer button (9). If the
engine fails to start, follow the instructions “How
To Start A Cold Engine”.
NOTE: Do not use the primer button (9) to
start a warm engine.
How To Start An Engine With A Frozen Electric
Starter (Figure 1)
If the electric starter is frozen and will not turn
the engine, follow the instructions below.
1. Pull as much starter rope as possible out of
the starter.
2. Release the starter handle and let it snap
back against the starter. Repeat until the
engine starts.
Warm engines will cause condensation in cold
weather. To prevent possible freeze−up of recoil
starter and engine controls, proceed as follows
after each snow removal job.
1. Run the snow thrower a few minutes after
throwing snow to prevent freeze−up of the
auger/impeller.
2. With engine off, allow engine to cool for
several minutes.
3. Pull starter rope very slowly until resistance
is felt, then stop. Allow the starter rope to
recoil. Repeat three times.
4. With the engine not running, wipe all snow
and moisture from the carburetor cover in
area of controls and levers. Also, move the
choke control and starter handle several
times.
How To Remove Snow or Debris From
The Auger Housing
WARNING: Do not attempt to
remove snow or debris that may
become lodged in auger housing
with your hands. Use the clean−out tool or
a pry bar to remove snow or debris.
(Figure 7) On some models, a clean−out tool
(1) is attached to the top of the auger housing.
Use the clean−out tool (1) to remove snow
from the auger housing.
1. Release the auger drive lever (5).
2. Stop the engine.
3. Remove the safety key (8).
4. Disconnect the spark plug wire.
5. Do not place your hands in the auger
housing (4) or the discharge chute (3).
6. (Figure 7) Use the clean-out tool (1) or a
pry bar to remove any snow or debris.
Snow Throwing Tips
1. For maximum snow thrower efficiency in
removing snow, adjust ground speed. Go
slower in deep, freezing or wet snow. If the
wheels slips, reduce forward speed.
2. Most efficient snow throwing is accomplished
when the snow is removed immediately after
if falls.
CAUTION: Do not overload the machine
capacity by attempting to clear snow at
too fast a rate.
3. For complete snow removal, slightly overlap
each previous path.
4. Whenever possible, discharge the snow
down wind.
5. For normal usage, set the skids so that the
scraper bar is 1/8” (3 mm) above the skids.
For extremely hard−packed snow surfaces,
adjust the skids upward so that the scraper
bar touches the ground.
6. Rocks and gravel must not be picked up and
thrown by the machine. On gravel or crushed
rock surfaces, set the skids at 1−1/4 inch
(32 mm) below the scraper bar. See “How To
Adjust The Height Of The Skids” in the
Maintenance section.
7. After each snow throwing job, allow the
engine to idle for a few minutes. The snow
and accumulated ice will melt off the engine.
8. Clean the snow thrower after each use.
9. Remove ice, snow and debris from the entire
snow thrower. Flush with water to remove all
salt or other chemicals. Wipe snow thrower
dry.
MAINTENANCE CHART
CUSTOMER RESPONSIBILITIES
SERVICE RECORDS
Fill in dates as you complete regular
service.
Before
Each
Use First 2
Hours
Every
5
Hours
Every
10
Hours
Every
25
Hours Each
Season Before
Storage SERVICE DATES
Check Engine Oil Level √ √ √
Change Engine Oil √ √
Check And Tighten All Screws and Nuts √ √
Check Spark Plug √ √
Adjust Drive Belt √ √ √
Check Fuel √
Drain Fuel √
Check Auger Clutch Cable Adjustment (See
Cable Adjustment) √ √
Check Traction Clutch Cable Adjustment
(See Cable Adjustment) √ √
Lubricate All Pivot Points √√
Lubricate Auger Shaft (See Shear Bolt
Replacement) √ √
Lubricate Drive Chains and Sprockets √ √
en
12
1740876
MAINTENANCE
NOTE: Illustrations are located on page 2
and on pages 32 through 38.
Use the following maintenance section to keep
your unit in good operating condition. All the
maintenance information for the engine is in the
engine manufacturer’s instructions. Before you
start the engine, read this book.
WARNING: Before you make an
inspection, adjustment (except
carburettor), or repair, disconnect
the wire from the spark plug.
General Recommendations
The warranty on this snow thrower does not
cover items that have been subjected to
operator abuse or negligence. To receive full
value from the warranty, the operator must
maintain the snow thrower as instructed in this
manual.
Some adjustments must be made periodically to
properly maintain the snow thrower.
After Each Use
GCheck for any loose or damaged parts.
GTighten any loose fasteners.
GCheck and maintain the auger.
GCheck controls to make sure they are
functioning properly.
GIf any parts are worn or damaged, replace
immediately.
GCheck all safety and instruction decals and
labels. Replace any decals or labels that are
missing or cannot be clearly read.
All adjustments in the Maintenance section of
this manual should be checked at least once
each season.
As Required
The following adjustment should be preformed
more than once each season.
1. Adjust the auger drive belt after the first 2 to
4 hours, again at mid−season, and twice
each season thereafter. See “How To Adjust
The Auger Drive Belt” in the Maintenance
section.
Lubrication
Every 10 Hours (Figure 13)
1. Lubricate the Zerk fittings (1) every ten
hours with a grease gun.
2. Each time a shear bolt is replaced, the auger
shaft must also be greased.
3. Lubricate all pivot points.
Every 25 Hours
Chute Rotation Gear
(Figure 5) Lubricate the chute rotation gear (1)
with automotive type oil.
Chains
1. (Figure 1) Move the speed shift lever (6) to
first gear.
2. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing (4).
WARNING: Drain the gasoline
outdoors, away from fire or flame.
3. (Figure 21) Loosen the bolts (3) on each
side of the bottom panel (2).
4. Remove the bottom panel (2).
5. (Figure 14) Lubricate the chains (5) with a
chain type lubricant.
6. Wipe the hexshaft and sprockets (6) with
5W30 motor oil.
NOTE: If grease or oil come in contact
with the disc drive plate (1) or the friction
wheel (3), damage can result. Clean off
any oil or grease with a alcohol base
solvent.
7. (Figure 21) Install the bottom panel (2).
8. Tighten the bolts (3) on each side of the
bottom panel (2).
Items Not To Lubricate (Figure 14)
1. Do not lubricate the hex shaft and
sprockets (6). All bearings and bushings are
lifetime lubricated. For storage, put a slight
amount of 5W−30 motor oil on a cloth and
wipe the hex shaft and sprockets (6) to
prevent rust.
2. If grease or oil comes in contact with the
disc drive plate (1) or the friction wheel
(3), the friction wheel (3) can be damaged.
Make sure to thoroughly clean the disc drive
plate (1) and the friction wheel (3).
CAUTION: Any greasing or oiling of the
above components can cause
contamination of the friction wheel (3). If
the disc drive plate (1) or the friction
wheel (3) become contaminated with
grease or oil, damage to the friction wheel
will result.
3. The auger gear case is lubricated at the
factory and does not require additional
lubrication. If for some reason the lubricant
leaks out, have the auger gear case checked
by a factory authorized service center.
How To Adjust The Height Of The Skids
(Figure 1)
This snow thrower is equipped with two height
adjustable skids (7). These skids elevate the
front of the snow thrower. For normal hard
surfaces, such as a paved driveway or walk,
adjust the skids as follows.
1. Put the snow thrower on a level surface.
2. Make sure both tires are equally inflated. The
correct air pressure is 14 PSI (1 BAR) to 17
PSI (1.25 BAR). Do not exceed the
maximum amount of air pressure shown on
the side of the tire.
3. Put the extra shear bolts (found in the parts
bag) under each end of the scraper bar (15)
next to the adjustable skids (7).
4. Loosen the mounting nuts (16) that hold the
adjustable skids (7). To bring the front of the
snow thrower down, raise each adjustable
skids (7). Tighten the mounting nuts (16).
NOTE: For rocky or uneven surfaces, raise
the front of the snow thrower by moving the
adjustable skids (7) down.
WARNING: Be certain to maintain
proper ground clearance for the
area to be cleared. Objects such as
gravel, rocks or other debris, if struck by
the impeller, can be thrown with sufficient
force to cause personal injury, property
damage or damage to the snow thrower.
How To Adjust The Scraper Bar
(Figure 1)
After considerable use, the scraper bar (15) will
become worn. The scraper bar (15), in
conjunction with the skids, must be adjusted to
allow 3 mm (1/8 inch) clearance between the
scraper bar (15) and the sidewalk or area to be
cleared.
1. Put the snow thrower on a level surface.
2. Make sure both tires are equally inflated.
The correct air pressure is 14 PSI (1 BAR )
to 17 PSI (1.25 BAR). Do not exceed the
maximum amount of air pressure shown on
the side of the tire.
3. Loosen the carriage bolts and nuts that hold
the scraper bar (15) to the auger housing
(4).
4. Adjust the scraper bar (15) to allow 1/8 inch
(3 mm) clearance between the scraper bar
(15) and the sidewalk or area to be cleared.
5. Tighten the carriage bolts and nuts. Make
sure that the scraper bar (15) is parallel with
the sidewalk or area to be cleared.
6. To extended the life of the scraper bar (15),
remove and reverse the mounting of the
scraper bar (15).
How To Check And Adjust The Cables
The traction drive cable and the auger drive
cable are adjusted at the factory. During normal
use, a cable can become stretched and must be
checked and adjusted as follows.
How To Check The Cables (Figure 15)
1. To check for correct adjustment, disconnect
the “Z” fitting (1) from the drive lever (2).
2. Move the drive lever (2) forward until the
drive lever (2) is contacting the plastic
bumper (3).
3. The control cable is correctly adjusted if the
center of the “Z” fitting (1) is aligned (4)
with the hole in the drive lever (2) and there
in no droop in the cable.
How To Adjust The Auger Drive Cable
1. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing.
WARNING: Drain the gasoline
outdoors, away from fire or flame.
2. (Figure 15) Disconnect the “Z” fitting (1)
from the drive lever (2).
3. (Figure 16) Pull the spring cover up to
expose the spring (5). Push the cable (6)
through the spring (5) to expose the square
end (7) on the cable (6).
4. Hold the square end (7) with pliers and
adjust the locknut (8) in or out until the
excess slack is removed.
5. Pull the cable (6) back through the spring
(5).
en
13
1740876
6. (Figure 15) Connect the “Z” fitting (1) to the
drive lever (2).
NOTE: When the auger drive belt is adjusted
or replaced, check and adjust the cable.
How To Adjust The Traction Drive Cable
1. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing.
WARNING: Drain the gasoline
outdoors, away from fire or flame.
2. (Figure 21) Loosen the bolts (3) on each
side of the bottom panel (2).
3. Remove the bottom panel (2).
4. (Figure 15) Disconnect the “Z” fitting (1)
from the traction drive lever (2).
5. (Figure 26) Slide the cable boot (3) off the
cable adjustment bracket (4).
6. Push the bottom of the traction control
cable (5) through the cable adjustment
bracket (4) until the “Z” hook (6) can be
removed.
7. Remove the “Z” hook (6) from the cable
adjustment bracket (4). Move the “Z” hook
(6) down to the next adjustment hole.
8. Pull the traction control cable (5) up
through the cable adjustment bracket (4).
9. Put the cable boot (3) over the cable
adjustment bracket (4).
10.(Figure 15) Install the “Z” fitting (1) to the
traction drive lever (2).
11. (Figure 14) To check the adjustment,
depress the drive lever and check the length
“A” of the drive spring (7). In correct
adjustment, the length “A” of the drive
spring (7) is as follows:
minimum 3 inches (76 mm)
maximum 3-3/8 inches (85 mm).
12.(Figure 21) Install the bottom panel (2).
13.Tighten the bolts (3) on each side of the
bottom panel (2).
How To Adjust The Belts
The belts will stretch during normal use. If you
need to adjust the belts due to wear or stretch,
proceed as follows.
How To Adjust The Auger Drive Belt
If the snow thrower will not discharge snow,
check the adjustment of the auger drive cable.
See “How To Check And Adjust The Cables” in
the Maintenance section. If the adjustment is
correct, then check the condition of the auger
drive belt. If the auger drive belt is damaged,
replace the auger drive belt. See “How To
Replace The Belts” in the Maintenance section.
If the auger drive belt is loose, adjust as follows.
1. Disconnect the spark plug wire.
2. (Figure 17) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
3. (Figure 18) Loosen the nut (2) on the idler
pulley (3) Move the idler pulley (3) 1/8 inch
toward the auger drive belt (4).
4. Tighten the nut (2).
5. (Figure 20) Depress the auger drive lever.
Check the tension on the auger drive belt
(4). In correct adjustment, the auger drive
belt (4) will deflect 1/2 inch (12.5 mm) (5)
with moderate pressure. If the adjustment is
not correct, repeat the adjustment.
8. (Figure 17) Install the belt cover (1). Tighten
screw (2).
9. Check the adjustment of the auger drive
cable. See “How To Check And Adjust The
Cables” in the Maintenance section.
10. Attach the spark plug wire.
Traction Drive Belt
The traction drive belt has constant spring
pressure and does not require an adjustment.
If the traction drive belt is slipping, replace the
belt. See “How To Replace The Belts” in the
Maintenance section.
How To Replace The Belts
The drive belts are of special construction and
must be replaced with original factory
replacement belts available from your nearest
authorized service center.
Some steps require the assistance of a second
person.
How To Remove the Auger Drive Belt
If the auger drive belt is damaged, the snow
thrower will not discharge snow. Replace the
damaged belt as follows.
1. Disconnect the spark plug wire.
2. (Figure 21) Remove the bolts (1) on each
side of the bottom panel (2).
3. Loosen the bolts (3) on each side of the
bottom panel (2).
4. Remove the bottom panel (2).
5. (Figure 17) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
6. (Figure 18) Loosen the belt guide (9). Pull
the belt guide (9) away from the auger
drive pulley (10).
7. Pull the idler pulley (3) away from the auger
drive belt (4) and slip the auger drive belt
(4) off of the idler pulley (3).
8. Remove the auger drive belt (4) from the
engine pulley (11). To remove the auger
drive belt (4), the engine pulley (11) may
have to be partially rotated.
9. (Figure 19) Remove the top four bolts (21)
that hold together the auger housing (22)
and the motor box (23). Loosen the bottom
two bolts (24). The auger housing (22) and
the motor box (23) can now be split apart for
removal of the belt.
10.(Figure 18) Remove the old auger drive
belt (4) from the auger drive pulley (10).
Replace the auger drive belt (4) with an
original factory replacement belt available
from an authorized service center.
11. Install the new auger drive belt (4) onto the
auger drive pulley (10).
NOTE: To assemble the auger housing
(22) to the motor box (23), have someone
hold the auger clutch lever in the
ENGAGED position. This will move the
idler arm and pulley (3) enough to allow
the auger drive pulley (10) to move back
into position.
12.Assemble the auger housing (22) to the
motor box (23) with the four bolts (21) that
were removed in step 9. Tighten the bottom
two bolts (24).
13.Install the auger drive belt (4) onto the
engine pulley (11).
14.Slip the auger drive belt (4) under the idler
pulley (3).
15.Adjust the auger drive belt (4). See “How To
Adjust The Auger Drive Belt” in the
Maintenance section.
16.Adjust the belt guide (9). See “How To
Adjust The Belt Guide” in the Maintenance
section.
17.(Figure 17) Install the belt cover (1). Tighten
screw (2).
18.(Figure 21) Install the bottom panel (2).
19.Install the bolts (1) on each side of the
bottom panel (2).
20.Tighten the bolts (1) and bolts (3) on each
side of the bottom panel (2).
21.Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
22.Connect the spark plug wire.
How To Remove the Traction Drive Belt
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt is worn or damaged, replace
the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See “How To
Remove The Auger Drive Belt” in the
Maintenance section.
3. (Figure 18) Remove the e−ring (17) from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward.
4. Remove the traction drive spring (16).
5. Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replace the traction
drive belt (13) with an original factory
replacement belt available from an
authorized service center.
6. Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto
engine pulley (15).
7. Make sure the traction drive idler pulley
(12) is properly aligned with the traction
drive belt (13).
8. Attach the traction drive spring (16).
9. Install the swing plate axle rod (18) and
secure with the e−ring (17) removed earlier.
10.(Figure 31) The bottom of the swing plate
(20) must be positioned between the
alignment tabs (19). Make sure the swing
plate (20) is properly secured.
NOTE: If the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
11. (Figure 18) Install and adjust the auger
drive belt (4). See “How To Remove The
Auger Drive Belt” in the Maintenance section.
12.Adjust the belt guide (9). See “How To
Adjust The Belt Guide” in the Maintenance
section.
13.(Figure 21) Install the bottom panel (2).
1741658
WARNING: Do not over-tighten, as this
may lift the lever and cause the auger
drive to be engaged without depressing
the Auger Control.
6. Release auger control. Auger must stop
within5 seconds.
7. If auger does not operate properly, stop
engine and recheck drive linkage
adjustments.
en
14
1740876
14.Tighten the bolts (3) on each side of the
bottom panel (2).
15.(Figure 17) Install the belt cover (1). Tighten
screw (2).
16.Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
17.Connect the spark plug wire.
How To Adjust The Belt Guide
1. Disconnect spark plug wire.
2. (Figure 17) Remove screw (2). Remove the
belt cover (1).
3. (Figure 1) Engage the auger drive lever (5).
4. (Figure 22) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 3 mm (1/8 inch).
5. If an adjustment is necessary, loosen the
mounting bolt for the belt guide (2). Move
the belt guide (2) to the correct position
(4). Tighten the mounting bolt for the belt
guide (2).
6. (Figure 17) Install the belt cover (1). Tighten
screw (2).
7. Connect the spark plug wire.
How To Adjust Or Replace The Friction
Wheel
How To Check The Friction Wheel
If the snow thrower will not move forward, check
the traction drive belt, the traction drive cable or
the friction wheel. If the friction wheel is worn or
damaged, it must be replaced. See “How To
Replace the Friction Wheel” in this section. If the
friction wheel is not worn or damaged, check as
follows.
1. (Figure 1) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
WARNING: Drain the gasoline
outdoors, away from fire or flame.
2. Disconnect the spark plug wire.
3. (Figure 21) Remove the bolts (1) on each
side of the bottom panel (2).
4. Loosen the bolts (3) on each side of the
bottom panel (2).
5. Remove the bottom panel (2).
6. (Figure 1) Position the shift speed lever (6)
in the lowest forward speed.
7. (Figure 23) Note the position of the friction
wheel (4). The correct distance “A” from the
right side of the friction wheel (4) to the
outside of the motorbox is as follows:
Tire Size Distance “A”
12 and 13 inch 4-1/8” (10.5 cm)
16 inch 4-5/16” (10.95 cm)
If the friction wheel (4) is not in the correct
position, adjust as follows.
How To Adjust The Friction Wheel
1. (Figure 1) Position the shift speed lever (6)
in the lowest forward speed.
2. (Figure 9) Loosen hex jam nut (9) on speed
select rod (2). Remove ball joint (6) from
shifter rod (7).
3. (Figure 23) Move the friction wheel (4) to
the correct position.
4. (Figure 9) Turn the adaptor (10) until the
ball joint (6) is aligned with the mounting
hole in the shifter rod (7). When aligned,
attach the ball joint (6) to the shifter rod (7).
5. (Figure 21) Install the bottom panel (2).
6. Install the bolts (1) on each side of the
bottom panel (2).
7. Tighten the bolts (1) and bolts (3) on each
side of the bottom panel (2).
How To Replace The Friction Wheel
If the friction wheel is worn or damaged, the
snow thrower will not move forward. The friction
wheel must be replaced as follows.
WARNING: Do not lubricate the
disc drive plate or the friction
wheel.
1. (Figure 1) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
WARNING: Drain the gasoline
outdoors, away from fire or flame.
2. Disconnect the spark plug wire.
3. (Figure 27) Remove the bolts (1) on each
side of the bottom panel (2).
4. Loosen the bolts (3) on each side of the
bottom panel (2).
5. Remove the bottom panel (2).
6. (Figure 28) Remove the rear support brace
(18).
7. (Figure 29) Use a 3/16” allen wrench and
remove the fastener that secures the right
axle clamp (30) to the axle (34).
8. Remove the right wheel (35), axle (34), axle
clamp (30), and washer (31).
9. (Figure 27) Remove the left wheel (10) from
the axle (11).
10.(Figure 30) Remove the fasterners that
secure the axle suport (32) to the motorbox.
Remove the axle suport (32) and bushing
(33).
11.Loosen (do not remove) the bolts that secure
the axle bearings (19) to the motor box.
12.Remove the clutch/drive sprocket
assembly (20) from the axle (11).
13.(Figure 31) Remove the four bolts (16) that
hold the bearings (7) on each side of the
hex shaft (8).
14.(Figure 32) Remove the hex shaft (8) and
bearings (7).
NOTE: Take special note of the position of
the washers (13).
15.(Figure 25) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
16.(Figure 25) Remove the friction wheel (5)
from the hub (6). Slip the friction wheel (5)
off the hex shaft (8).
17.Assemble the new friction wheel (5) onto
hub (6) with the fasteners removed earlier.
18.(Figure 32) Install the hex shaft (8) and
bearings (7) with the four bolts removed
earlier.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are
properly aligned with the actuator arms
(14).
19.Make sure the hex shaft (8) turns freely.
20.To install the remaining parts, reverse the
above steps.
21.Check the adjustment of the friction wheel.
See “How To Adjust The Friction Wheel” in
this section.
22.Make sure the friction wheel and the disc
drive plate are free from grease or oil.
23.(Figure 27) Install the bottom panel (2).
24.Install the bolts (1) on each side of the
bottom panel (2).
25.Tighten the bolts (1) and bolts (3) on each
side of the bottom panel (2).
26.Connect the spark plug wire.
How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with
special shear bolts. These shear bolts are
designed to break and protect the machine if an
object becomes lodged in the auger housing. Do
not use a harder bolt as the protection provided
by the shear bolt will be lost.
WARNING: For safety and to
protect the machine, use only
original equipment shear bolts.
To replace a broken shear bolt, proceed as
follows. Extra shear bolts were provided in the
assembly parts bag.
1. Stop the engine.
2. Disconnect the spark plug wire. Make sure
all moving parts have stopped.
3. (Figure 13) Lubricate the auger shaft Zerk
fitting (1), if equipped, with a grease gun.
4. (Figure 24) Align the hole in the auger with
the hole in the auger shaft. Install the new
shear bolt (2), spacer (3), and locknut (4).
NOTE: If the model has a 33” (84 cm)
Auger Housing, the spacer (3) is not
required.
5. Connect the spark plug wire.
How To Prepare The Snow Thrower For
Storage
WARNING: Do not remove gasoline
while inside a building, near a fire,
or while you smoke. Gasoline
fumes can cause an explosion or a fire.
If the snow thrower is to be stored for an
extended period, refer to the engine
manufacturer’s operating manual (included with
some models) for important maintenance or
storage details.
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Never store the snow thrower with fuel in the
tank inside a building where ignition sources
are present such as hot water and space
heaters, clothes dryers, and the like. Allow the
engine (motor) to cool before storing in any
enclosure.
4. Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
5. Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder.
Slowly pull the recoil−start grip so that the oil
will protect the cylinder. Install a new spark
plug in the cylinder.
6. Thoroughly clean the snow thrower.
7. Lubricate all lubrication points. See the
Maintenance section.
1741658
en
15
1740876
8. Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible moving
parts for damage, breakage and wear.
Replace if necessary.
9. Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
10.Put the unit in a building that has good
ventilation.
11.If the machine must be stored outdoors,
block up the snow thrower to be sure the
entire machine is off the ground.
12.Cover the snow thrower with a suitable
protective cover that does not retain
moisture. Do not use plastic.
How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer’s authorized or approved
replacement parts. Do not use attachments or
accessories not specifically recommended for
this unit. In order to obtain proper replacement
parts you must supply the model number (see
nameplate).
To obtain replacement parts, contact your local
Dealer.
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer’s authorized service centre found
in the yellow pages of the telephone directory.
Also, see the individual engine or transmission
warranties to order replacement parts.
When ordering the following information is
required:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
TROUBLE SHOOTING CHART
TROUBLE CAUSE CORRECTION
Difficult starting Defective spark plug. Replace spark plug.
Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with
fresh fuel.
Engine runs erratic Blocked fuel line, empty gas tank, or stale
gasoline. Clean fuel line; check fuel supply; add fresh
gasoline.
Engine stalls Unit running on CHOKE. Set choke lever to RUN position.
Engine runs erratic;
Loss of power Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with
fresh fuel.
Excessive vibration Loose parts: damaged impeller. Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and make all
necessary repairs. If vibration continues, have
the unit serviced by a competent repairman.
Unit fails to propel itself Drive belt loose or damaged. Replace drive belt.
Incorrect adjustment of traction drive cable. Adjust traction drive cable.
Worn or damaged friction wheel. Replace friction wheel.
Unit fails to discharge snow Auger drive belt loose or damaged. Adjust auger drive belt; replace if damaged.
Auger control cable not adjusted correctly. Adjust auger control cable.
Shear bolt broken. Replace shear bolt.
Discharge chute clogged. Stop engine immediately and disconnect spark
plug wire. Clean discharge chute and inside of
auger housing.
Foreign object lodged in auger. Stop engine immediately and disconnect spark
plug wire. Remove object from auger.
1741658
en
16
1741658
BRIGGS & STRATTON CORPORATION OWNER WARRANTY POLICY
Effective January 1, 2007replaces all undated Warranties and all Warranties dated before January 1, 2007
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the product that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective
for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in your area. For
warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.murray.com.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL
IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE
EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and
some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion
may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to
country.
LIMITED WARRANTY
WARRANTY TERMS
Consumer Commercial Condition of
Brand / Unit Use Use Warranty Term
Single Stage Snowthrower 1 year 90 days......... .............
Dual Stage Snowthrower 2 year 90 days.......... .............
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of
time stated in the table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means
all other uses, including use for commercial, income producing or rental purposes. Once product has experienced commercial use, it shall
thereafter be considered as commercial use for purposes of this warranty.
No warranty registration is necessary to obtain warranty on Murray branded products. Save your proof of purchase receipt. If you do not
provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will be used to
determine the warranty.
ABOUT YOUR WARRANTY
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty
repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example,
warranty service would not apply to the product if damage occurred because of misuse, lack of routine maintenance, shipping, handling,
warehousing or improper installation. Similarly, the warranty is void if the serial number on the product has been removed or the product
has been altered or modified.
This warranty covers product related defective material and/or workmanship only. To avoid misunderstanding which might occur be-
tween the customer and the Dealer, listed below are some of the causes of product failure that the warranty does not cover.
•Normal Wear: Small Engine Powered Equipment, like all mechanical devices, needs periodic parts and service to perform well. Warranty does not
cover repair when normal use has exhausted the life of the product or part.
•Installation: This warranty does not apply to product that has been subjected to improper or unauthorized installation, alteration or modification. Nor
installations that prevent starting, cause unsatisfactory engine performance.
•Improper Maintenance: The life of this product depends upon the conditions under which it operates, and the care it receives. Recommended
maintenance and adjustment intervals are stated in the Operator’s Manual. Often product, such as tillers, edgers, rotary mowers, are used in dusty
or dirty conditions, which can cause what appears to be premature wear. Such wear, when caused by dirt, dust, or other abrasive material entering
the product because of improper maintenance is not covered by warranty. The warranty will not cover repairs due to problems caused by replace-
ment parts that are not original manufactured part(s).
•Incorrect and/or insufficient fuel or lubrication: This warranty does not cover damage caused by the use of stale fuel, or altered gasolines. Dam-
age to engine or engine components ie, combustion chamber, valves, valve seats, valve guides, burned starter motor windings caused by use of
alternate fuels such as liquified petroleum, natural gas, are not covered unless engine is certified for this operation. Parts which are scored or bro-
ken because product was operated with insufficient, contaminated or incorrect grade of lubricating oil as well as product components damaged due
to lack of lubrication are not covered.
•Operational Misuse: Proper operation of the product is stated in the Operator’s Manual. Product damaged by overspeeding, overheating, or opera-
tion in a confined area without sufficient ventilation. Product broken by excessive vibration caused by a loose engine mounting, loose or unbalanced
blades, impellers, overspeeding, or bent crankshaft due to striking of solid object. Damage or malfunctions resulting from accidents, abuse, or im-
proper servicing or freezing or chemical deterioration, as well as operating in excess of recommended capacities as outlined in the Operator’s
Manual are not covered.
•Routine tune-up, wear items or adjustments: This warranty excludes wear items such as oil, belts, blades, o-rings, filters, etc.
•Other exclusions: Repair or adjustments for part(s) that are not manufactured by Briggs & Stratton Corporation, are not covered, see warranty for
respective manufacturers. This warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers con-
trol. Also excluded are used, reconditioned, and demonstration products.
Warranty service is available only through Authorized Service Dealers. Locate your nearest dealer in our locator map at www.murray.com.
fr
17
1740876
TABLE DES MATIÈRES
SYMBOLES DE DANGERS ET LEURS
81SNOITACIFINGIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYMBOLES DE DANGERS ET LEURS
81SNOITACIFINGIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32EGATNOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42TNEMENNOITCNOF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLEAU DE MAINTENANCE 26. . . . . . . . . . . . . . . . . . . . . . . . .
ENTRETIEN 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLEAU DE DEPANNAGE 30. . . . . . . . . . . . . . . . . . . . . . . . . . .
1741658
GARANTIE 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Levier d’embrayage des roues -- Ce levier sert à embrayer
et à débrayer la marche avant ou la marche arrière. Pousser
le levier pour embrayer et le relâcher pour débrayer.
fr
18
1740876
8!
' : :$ :
& & $9
9 9
9 9
9:
B /
-
8
K
" D L 2 1
D 1B
DB/
' BB L
BB C D / H
1
1
#, D,
" BB
1 DB/
'J
1 D 1
B
( ,
E
8!
' : :$ :
$ &
$ & - $
: @ $
'J
-
8 C DJ
:
8
2
%
"
'J
Clé de
contact
Contact
désactivé
Contact
activé
# DI
" @
Embrayage de traction
Embrayage
de la fraise
Engager
Collecteur de la
fraise
Traction
" 1
#
" E
Appuyer pour
engager le
démarreur
électrique
Démarreur
électrique
Démarrage
du moteur
Moteur en
marche
Moteur à
l’arrêt
DROIT
Déversoir
GAUCHE HAUT BAS
Déflecteur
Engager
Désengager
fr
119
1740876
C& : @:
*& =
: 9:/ :
•) / : : :
: $ 9:$ : $
•? : 9
9 9:$
•) / 9:$ $
/ :
? :
•! " $
: :
9:$ & :
•! ? = 9
: :
? D ?
: @ :
" /"
• : ? : $ : )
9 = 9 $ $ :: >
• ) : 9 +"
"? )
:
•) : : A
$ : :
D
+'(%
9:/
:/ ) / 9:/
$
? :
:; : ?
•%: 9: :
•) / = ": 9:/
• : = 9? $ ; =
9? = 9 9 D &
•% : $ 9
@ 9:$
6 : :
: 9:$ ;
+'(%
% / ? : :/:
) / /
/
:
•& 9
9:$ A :: $
/" / :
@ / /
•& / $
/: : " $ <
:: ? : : /
9/
•2&A : $ &
!$& : : 9
:: $ / 9/
•6:& : : ;
& :
•; : / : & & $
; 9 :& :
$ 9:$ 9 : :&
& : : :
:
• = 9? : $ ;
= 9? / D 9:/
•' 9:$ : %
:: ; '
:: : :
+'(%
: " &
"$
9 " @
:
•%: = 9":
•) :
: ? ?
'G%&88"(&
fr
120
1740876
9 "?
"
- " @ :;
E
2$%8 +. %"#288' +. %M8%G$%
•'& & "
9 : 9
• : 9 = 9":5 :
:
•) : : 9
•! 9 = :
9
•4: :$ 9 :
=
:
2$%8 +. +M"'%%' +. "$&.%
•9 $ 9:
: 9 =
•) 9
:
• 9 : $9 ::
:
• #6+)7-)
(#-4+7!'F+. & 2
(6%+. = 9 : /$9=
$ :
2$%8 +. $(-&$(("(& + 2DMA.#"(&
•) : ?
2$%8 +. &%'(8#$%& + 2DMA.#"(&
•+ : 9 4%+
2$%8 + 2D(&%#$8' +D88(- $. +
2DMA.#"(& 'G- + 2D88(- +'(8 2 %M8%G$%
•+ = ; ? A
9 $ ;
9 A 9
'G%&88"(&
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Simplicity MULT-LANGUAGE OPERATOR'S MANUAL-15.50 GROSS TORQUE, 29-INCH Manuel utilisateur
- Catégorie
- Souffleuses à neige
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Simplicity ENGLISH / FRENCH OPERATOR'S MANUAL-9.0 GROSS TORQUE, 24" Manuel utilisateur
-
-
-
Simplicity 1695386 Manuel utilisateur
-
-
-
-
