Skil 5003 Instructions Manual

Marque: Skil

Modèle: 5003

Catégorie: Outils électroportatifs

Taper: Instructions Manual

Ce manuel convient également à

CIRCULAR SAW

5166 (F0155166 . . )

SKIL Europe BV - Konijnenberg 60 08/08 2610394155

4825 BD Breda - The Netherlands

www.skileurope.com

ME77

ORIGINAL INSTRUCTIONS . . . . . . . . . . . . .

NOTICE ORIGINALE . . . . . . . . . . . . . . . . . 11

ORIGINALBETRIEBSANLEITUNG . . . . . .

ORIGINELE GEBRUIKSAANWIJZING. . . . 21

BRUKSANVISNING I ORIGINAL . . . . . . . .

ORIGINAL BRUGSANVISNING . . . . . . . . . 30

ORIGINAL DRIFTSINSTRUKS. . . . . . . . . . 35

ALKUPERÄISET OHJEET . . . . . . . . . . . . .

MANUAL ORIGINAL . . . . . . . . . . . . . . . . . 44

MANUAL ORIGINAL. . . . . . . . . . . . . . . . . .

ISTRUZIONI ORIGINALI . . . . . . . . . . . . . . 54

EREDETI HASZNÁLATI UTASÍTÁS. . . . . . 59

PÒVODNÍM NÁVODEM K POUÎÍVÁNÍ . . . 64

OR‹J‹NAL ‹ﬁLETME TAL‹MATI . . . . . . . . . 68

INSTRUKCJÑ ORYGINALNÑ. . . . . . . . . . . 73

ОРИГИНАЛНЬОЕ РУКОВОДСТВО

ПО ЭКСПЛУАТАЦИИ . . . . . . . . . . . . . . . .

ОРИГІНАЛЬНА ІНСТРУКЦІЯ

З ЕКСПЛУАТАЦІЇ . . . . . . . . . . . . . . . . . . .

ΠΡΩΤΤΥΠ ∆ΗΓΙΩΝ ΡΗΣΗΣ . . . . . . 89

INSTRUCØIUNI DE FOLOSIRE

ORIGINALE . . . . . . . . . . . . . . . . . . . . . . . .

ОРИГИНАЛНО РЪКОВОДСТВО

ЗА ЕКСПЛОАТАЦИЯ . . . . . . . . . . . . . . .

100

PÔVODN¯ NÁVOD NA POUÎITIE . . . . . 105

ORIGINALNE UPUTE ZA RAD . . . . . . . . 110

ORIGINALNO UPUTSTVO ZA RAD . . . . 114

IZVIRNA NAVODILA . . . . . . . . . . . . . . . . 119

ALGUPÄRANE KASUTUSJUHEND . . . . 123

ORI˛INÅLÅ LIETO·ANAS PAMÅC±BA. . 127

ORIGINALI INSTRUKCIJA. . . . . . . . . . . . 133

FIN

SRB

SLO

EST

66 mm

90°

EH HAD G

51 mm

45°

5000

190 mm

MAX.

16 mm

175 mm

MIN.

16 mm

5166

1250

Watt

4,5 kg

EPTA 01/2003

3 mm

F G Q

SKIL Nr.

ACCESSORIES

12x 190 mm 16 mm 1,5 / 2,2 2610373172

24x 190 mm 16 mm 1,5 / 2,2 2610373173

24x 190 mm 16 mm 1,4 / 2,4 2610373174

60x 184 mm 16 mm 1,8 / 2,5 2610395706

72x 190 mm 16 mm 1,4 / 2,4 2610373175

2610387402

Circular saw 5166

INTRODUCTION

• This tool is intended for lengthways and crossways

cutting of wood with straight cuts as well as angle cuts

to 45°; with the appropriate saw blades also non-ferrous

metals, light building materials and plastics can be cut

• Read and save this instruction manual 2

TECHNICAL SPECIFICATIONS 1

SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious

injury. Save all warnings and instructions for future

reference. The term “power tool” in the warnings refers to

your mains-operated (corded) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce risk

of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location is

unavoidable, use an earth leakage circuit breaker.

Use of an earth leakage circuit breaker reduces the risk

of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or under

the influence of drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source, picking up or carrying the tool. Carrying

power tools with your ﬁ nger on the switch or energising

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR CIRCULAR SAWS

DANGER

•

Keep hands away from cutting area and the

blade; keep your second hand on front handle

(if both hands are holding the saw, they can not be cut

by the blade)

• Do not reach underneath the workpiece (the guard

cannot protect you from the blade below the workpiece)

• Adjust the cutting depth to the thickness of the

workpiece (less than a full tooth of the blade teeth

should be visible below the workpiece)

• Never hold piece being cut in your hands or across

your leg (it is important to support the work properly to

minimise body exposure, blade binding, or loss of

control)

• Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord (contact with a

“live” wire will also make exposed metal parts of the

tool “live” and shock the operator)

• When ripping always use a rip fence or straight edge

guide (this improves the accuracy of cut and reduces

the chance for blade binding)

• Always use blades with correct size and shape of

arbor holes (diamond or round) (blades that do not

match the mounting hardware of the saw will run

eccentrically, causing loss of control)

• Never use damaged or incorrect blade washers or

bolts (the blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation)

KICKBACK - CAUSES

• Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to

lift up and out of the workpiece toward the operator

• When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator

• If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the

top surface of the wood causing the blade to climb out

of the kerf and jump back towards operator

KICKBACK - OPERATOR PREVENTION

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below

• Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces;

position your body to either side of the blade, but

not in line with the blade (kickback could cause the

saw to jump backwards, but kickback forces can be

controlled by the operator, if proper precautions are

taken)

• When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop; never attempt to remove the saw

from the work or pull the saw backwards while the

blade is in motion or kickback may occur (investigate

and take corrective actions to eliminate the cause of

blade binding; avoid cutting nails or screws)

• When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material (if saw blade is binding,

it may walk up or kickback from the workpiece as the

saw is restarted)

• Support large panels to minimise the risk of blade

pinching and kickback (large panels tend to sag under

their own weight; supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel)

• Do not use a dull or damaged blade (unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback)

• Blade depth and bevel adjusting locking levers must

be tight and secure before making cut (if blade

adjustment shifts while cutting, it may cause binding

and kickback)

• Use extra caution when making a plunge cut into

existing walls or other blind areas (the protruding

blade may cut objects that can cause kickback)

WARNING

• Check lower guard for proper closing before each

use

• Do not operate the saw if lower guard does not

move freely and close instantly

• Never clamp or tie the lower guard into the open

position

• If saw is accidentally dropped, lower guard may be

bent; disconnect the plug, raise the lower guard with

the retracting handle and make sure it moves freely and

does not touch the blade or any other part, in all angles

and depths of cut

• Check the operation of the lower guard spring; if the

guard and the spring are not operating properly,

they must be serviced before use (lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris)

• Lower guard should be retracted manually only for

special cuts such as plunge cuts and compound

cuts; raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released (for all other sawing, the lower guard

should operate automatically)

• Always observe that the lower guard is covering the

blade before placing saw down on bench or floor

(an unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path; be

aware of the time it takes for the blade to stop after

switch is released)

GENERAL

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to ﬁ re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with

a capacity of 16 Amps (U.K. 13 Amps)

• In case of jamming or electrical or mechanical

malfunction, immediately switch off the tool and

disconnect the plug

• SKIL can assure ﬂ awless functioning of the tool only

when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Never use the tool without the original protection guard

system

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use tool when cord is damaged; have it replaced

by a qualiﬁ ed person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• This tool is not suitable for wet cutting

• After switching off your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

• Never use circular saw blades made of high speed steel

(HSS)

• Never use grinding/cutting discs with this tool

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause

allergic reactions and/or respiratory diseases to the

operator or bystanders); wear a dust mask and work

with a dust extraction device when connectable

• Certain kinds of dust are classiﬁ ed as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Do not attempt to cut extremely small workpieces

• Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

• Do not work overhead with the tool

• Only use a saw table provided with a switch that

prevents restarting of the motor after interruption of

voltage

• Only use a saw table provided with a kerf guide

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

• Changing saw blade 3

! disconnect the plug

- take blade wrench A from storage B

- push spindle-lock button C and hold it while you

remove blade bolt D with blade wrench

! push spindle-lock button C only when tool is at a

standstill

- release spindle-lock button C

- remove ﬂ ange E

- open lower guard F with lever G and hold it while you

change saw blade with saw teeth and arrow printed

on saw blade pointing in same direction as arrow on

lower guard

- release lower guard F

- mount ﬂ ange E

! make sure that clamping surfaces H of flanges

are perfectly clean and face the blade

- push spindle-lock button C and hold it while you

tighten blade bolt with blade wrench 1/8 turn past

ﬁ nger tight (ensures slippage of saw blade when it

encounters excessive resistance thus reducing motor

overload and saw kickback)

- release spindle-lock button C

• Adjusting cutting depth (0-66 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever J

- raise/lower foot K until desired cutting depth is set on

scale using indicator L

- tighten lever J

• Adjusting cutting angle (0-45°) 5

- loosen knob M

- tilt tool until desired cutting angle is set on scale

using indicator N

- tighten knob M

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

• 90° Cutting angle check 5

- adjust and tighten foot K to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for 90° angle between the blade and bottom of

foot with a square

- if adjustment is needed, tilt and tighten foot to 45°

and bend tab P with an adjustable wrench

• Line-of-cut indicator Q 6

- for guiding tool along desired line of cut marked on

the workpiece

- for a straight 0° cut or a 45° bevel cut use the

indicator line concerned

- allows you to choose whether waste material is on

inner or outer side of blade

! the wide part of the foot should rest on the

supported part of the workpiece

! cutting width is determined by width of blade

teeth and not bywidth of blade body

! always make trial cuts first to verify actual line of

cut

• Dust suction

- connect vacuum cleaner to extension R 7

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

• Operating the tool 7

- connect plug to power source

- always hold handle S ﬁ rmly with one hand and

handle T ﬁ rmly with the other hand

- place tool with front end of foot ﬂ at on workpiece

! ensure that the saw teeth are not engaged into

the workpiece

- switch on tool by ﬁ rst pressing knob U (= safety

switch which cannot be locked) and then pulling

trigger V

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard F opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever G only for special cuts such as plunge

cuts)

- do not force the tool; apply light and continuous

pressure

! while working, always hold the tool at the grey-

coloured grip area(s)

- after completing the cut switch off tool by releasing

trigger V

! ensure that the blade has come to a complete

standstill, before you lift the tool from the

workpiece

APPLICATION ADVICE

• Always face the good side of the workpiece down to

ensure minimum splintering

• Only use sharp saw blades of the correct type 8

- quality of cut improves by the number of teeth

- carbide tipped blades stay sharp up to 30 times

longer than ordinary blades

• Rip fence W 9

- for making exact cuts along a workpiece edge

- can be inserted in either side of foot

Adjusting rip fence

- loosen knob X

- adjust to desired cutting width by using rip fence

scale (use line-of-cut indicator Q as 0-reference)

- tighten knob X

• Plunge cutting 0

- set desired cutting depth

- tilt tool forward with line-of-cut indicator Q lined up

with desired line of cut marked on the workpiece

- open lower guard F with lever G

- just before blade enters workpiece, switch on tool

and gradually lower back end of tool using front end

of foot as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever G

! never pull tool backwards

• Cutting large panels !

- support panel close to the cut either on ﬂ oor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

- in case rip fence does not allow desired width of cut,

clamp or nail straight piece of wood to workpiece as

a guide, and use the right side of the foot against this

guide

• Vibration level

The vibration emission level stated at the back of this

instruction manual has been measured in accordance

with a standardised test given in EN 60745; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signiﬁ cantly increase the exposure level

- the times when the tool is switched off or when it is

running but not actually doing the job, may

signiﬁ cantly reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

• Clean saw blade immediately after use (especially from

resin and glue)

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol @ will remind you of this when the need for

disposing occurs

Scie circulaire 5166

INTRODUCTION

• Cet outil est conçu pour effectuer dans le bois des

coupes droites longitudinales et transversales ainsi que

des angles d’onglet jusqu’à 45°; muni de lames de scie

correspondantes, il est capable de scier des matériaux

non-ferroux, des matériaux de construction légers et

des matières plastiques

• Lisez et conservez ce manuel d’instructions 2

SPECIFICATIONS TECHNIQUES 1

SECURITE

INSTRUCTIONS GENERALES DE SECURITE

ATTENTION! Lisez tous les avertissements de

sécurité et toutes les instructions. Ne pas suivre les

avertissements et instructions peut entraîner un choc

électrique, un incendie et/ou de graves blessures sur les

personnes. Conservez tous les avertissements et

toutes les instructions pour pouvoir s’y reporter

ultérieurement. La notion d’”outil électroportatif” dans les

avertissements se rapporte à des outils électriques

raccordés au secteur (avec câble de raccordement).

1) SECURITE DE LA ZONE DE TRAVAIL

a) Maintenez l’endroit de travail propre et bien éclairé.

Un lieu de travail en désordre ou mal éclairé augmente

le risque d’accidents.

b) N’utilisez pas l’outil dans un environnement

présentant des risques d’explosion et où se trouvent

des liquides, des gaz ou poussières inflammables.

Les outils électroportatifs génèrent des étincelles

risquant d’enﬂ ammer les poussières ou les vapeurs.

c) Tenez les enfants et autres personnes éloignés

durant l’utilisation de l’outil électroportatif.

En cas d’inattention vous risquez de perdre le

contrôle sur l’outil.

2) SECURITE RELATIVE AU SYSTEME ELECTRIQUE

a) La fiche de secteur de l’outil électroportatif doit être

appropriée à la prise de courant. Ne modifiez en

aucun cas la fiche. N’utilisez pas de fiches

d’adaptateur avec des outils avec mise à la terre.

Les ﬁ ches non modiﬁ ées et les prises de courant

appropriées réduisent le risque de choc électrique.

b) Evitez le contact physique avec des surfaces mises

à la terre telles que tuyaux, radiateurs, fours et

réfrigérateurs. Il y a un risque élevé de choc électrique

au cas où votre corps serait relié à la terre.

c) N’exposez pas l’outil électroportatif à la pluie ou à

l’humidité. La pénétration d’eau dans un outil

électroportatif augmente le risque d’un choc électrique.

d) N’utilisez pas le câble à d’autres fins que celles

prévues, n’utilisez pas le câble pour porter l’outil ou

pour l’accrocher ou encore pour le débrancher de la

prise de courant. Maintenez le câble éloigné des

sources de chaleur, des parties grasses, des bords

tranchants ou des parties de l’outil en rotation.

Un câble endommagé ou torsadé augmente le risque

d’un choc électrique.

e) Au cas où vous utiliseriez l’outil électroportatif à

l’extérieur, utilisez une rallonge autorisée

homologuée pour les applications extérieures.

L’utilisation d’une rallonge électrique homologuée pour

les applications extérieures réduit le risque d’un choc

électrique.

f) Si l’usage d’un outil dans un emplacement humide

est inévitable, utilisez un disjoncteur de fuite à la

terre. L’utilisation d’un disjoncteur de fuite à la terre

réduit le risque de choc électrique.

3) SECURITE DES PERSONNES

a) Restez vigilant, surveillez ce que vous faites. Faites

preuve de bon sens en utilisant l’outil électroportatif.

N’utilisez pas l’outil lorsque vous êtes fatigué ou

après avoir consommé de l’alcool, des drogues ou

avoir pris des médicaments. Un moment d’inattention

lors de l’utilisation de l’outil peut entraîner de graves

blessures sur les personnes.

b) Portez des équipements de protection.

Portez toujours des lunettes de protection.

Le fait de porter des équipements de protection

personnels tels que masque anti-poussières,

chaussures de sécurité antidérapantes, casque de

protection ou protection acoustique suivant le travail

à effectuer, réduit le risque de blessures.

✎

138

✎

139

✎

140

141

CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following

standards or standardized documents: EN 60 745, EN 55 014, in accordance with the provisions of the directives 2006/95/EC,

2004/108/EC, 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009 on).

NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 93 dB(A) and the sound power

level 104 dB(A) (standard deviation: 3 dB), and the vibration < 2.5 m/s

(hand-arm method; uncertainty K = 1.5 m/s

Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE DÉCLARATION DE CONFORMITÉ Nous déclarons sous notre propre responsabilité que ce produit est en conformité avec les

normes ou documents normalisés suivants: EN 60 745, EN 55 014, conforme aux réglementations 2006/95/CE, 2004/108/CE,

98/37/CE (jusqu’au 28.12.2009), 2006/42/CE (à partir du 29.12.2009).

BRUIT/VIBRATION Mesuré selon EN 60 745 le niveau de la pression sonore de cet outil est 93 dB(A) et le niveau de la puissance

sonore 104 dB(A) (déviation standard: 3 dB), et la vibration < 2,5 m/s

(méthode main-bras; incertitude K = 1,5 m/s

Dossier technique auprès de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE KONFORMITÄTSERKLÄRUNG Wir erklären in alleiniger Verantwortung, daß dieses Produkt mit den folgenden Normen oder

normativen Dokumenten übereinstimmt: EN 60 745, EN 55 014, gemäß den Bestimmungen der Richtlinien 2006/95/EG,

2004/108/EG, 98/37/EG (bis 28.12.2009), 2006/42/EG (ab 29.12.2009).

GERÄUSCH/VIBRATION Gemessen gemäß EN 60 745 beträgt der Schalldruckpegel dieses Gerätes 93 dB(A) und der Schal-

leistungspegel 104 dB(A) (Standard- abweichung: 3 dB), und die Vibration < 2,5 m/s

(Hand-Arm Methode; unsicherheit K = 1,5 m/s

Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten:

EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009),

2006/42/EG (vanaf 29-12-2009).

GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 93 dB(A) en het geluidsvermogen-

niveau 104 dB(A) (standaard deviatie: 3 dB), en de vibratie < 2,5 m/s

(hand-arm methode; onzekerheid K = 1,5 m/s

Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE KONFORMITETSFÖRKLARING Vi intygar och ansvarar för, att denna produkt överensstämmer med följande norm och

dokument: EN 60 745, EN 55 014, enl. bestämmelser och riktlinjema 2006/95/EG, 2004/108/EG, 98/37/EG (till 28.12.2009),

2006/42/EG (from 29.12.2009).

LJUD/VIBRATION Ljudtrycksnivån som uppmätts enligt EN 60 745 är på denna maskin 93 dB(A) och ljudeffektnivån 104 dB(A)

(standard deviation: 3 dB), och vibration < 2,5 m/s

(hand-arm metod; onoggrannhet K = 1,5 m/s

Teknisk tillverkningsdokumentation finns hos: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE KONFORMITETSERKLÆRING Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende

normer eller normative dokumenter: EN 60 745, EN 55 014, i henhold til bestemmelserne i direktiverne 2006/95/EF, 2004/108/EF,

98/37/EF (indtil 28.12.2009), 2006/42/EF (fra 29.12.2009).

STØJ/VIBRATION Måles efter EN 60 745 er lydtrykniveau af dette værktøj 93 dB(A) og lydeffektniveau 104 dB(A) (standard

deviation: 3 dB), og vibrationsniveauet < 2,5 m/s

(hånd-arm metoden; usikkerhed K = 1,5 m/s

Teknisk dossier hos: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE SAMSVARSERKLÆRING Vi erklærer at det er under vårt ansvar at dette produkt er i samsvar med følgende standarder eller

standard- dokumenter: EN 60 745, EN 55 014, i samsvar med reguleringer 2006/95/EF, 2004/108/EF, 98/37/EF (frem til 28.12.2009),

2006/42/EF (fra 29.12.2009).

STØY/VIBRASJON Målt ifølge EN 60 745 er lydtrykknivået av dette verktøyet 93 dB(A) og lydstyrkenivået 104 dB(A) (standard

deviasjon: 3 dB), og vibrasjonsnivået < 2,5 m/s

(hånd-arm metode; usikkerhet K = 1,5 m/s

Tekniske underlag hos: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen

standardien ja standardoimisasiakirjojen vaatimusten mukainen EN 60 745, EN 55 014, seuraavien sääntöjen mukaisesti

2006/95/EY, 2004/108/EY, 98/37/EY (28.12.2009 asti), 2006/42/EY (29.12.2009 alkaen).

MELU/TÄRINÄ Mitattuna EN 60 745 mukaan työkalun melutaso on 93 dB(A) ja yleensä työkalun äänen voimakkuus on 104 dB(A)

(keskihajonta: 3 dB), ja tärinän voimakkuus < 2,5 m/s

(käsi-käsivarsi metodi; epävarmuus K = 1,5 m/s

Tekninen tiedosto kohdasta: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE DECLARACION DE CONFORMIDAD Declaramos bajo nuestra sola responsabilidad que este producto está en conformidad

con las normas o documentos normalizados siguientes: EN 60 745, EN 55 014, de acuerdo con las regulaciones 2006/95/CE,

2004/108/CE, 98/37/CE (hasta el 28.12.2009), 2006/42/CE (a partir del 29.12.2009).

RUIDOS/VIBRACIONES Medido según EN 60 745 el nivel de la presión acústica de esta herramienta se eleva a 93 dB(A) y el nivel de

la potencia acústica 104 dB(A) (desviación estándar: 3 dB), y la vibración a < 2,5 m/s

(método brazo-mano; incertidumbre K = 1,5 m/s

Expediente técnico en: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

FIN

08 SKIL Europe BV A. v.d. Kloot

142

08 SKIL Europe BV A. v.d. Kloot

ЗАЯВЛЕНИЕ О СООТВЕТСТВИИ Мы с полной ответственностыо заявляем, что это изделие соответствует следующим

стандартам или станда ртизованным документам: EN 60 745, EN 55 014, в соответсувии с инструкциями 2006/95/EC,

2004/108/EC, 98/37/EC (до 28.12.2009), 2006/42/EC (начиная с 29.12.2009).

ШУМНОСТИ/ВИБРАЦИИ При измерении в соответствии co стандартoм EN 60 745 уровень звукового давления для этого

инструмента составляет 93 дБ (A) и уровeнь звуковой мощности - 104 дБ (A) (стандартное отклонение: 3 dB), и вибрации - <

2,5 м/с

(по методу для рук; недостоверность K = 1,5 м/с

Техническая документация у: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE ВІДПОВІДНІСТЬ Ми заявляємо, що відповідність даного продукту наступним стандартам і регулюючим документам

повністю нашою відповідальністю: EN 60 745, EN 55 014, відповідно до положень директив 2006/95/EG, 2004/108/EG,

98/37/EG до 28.12.2009 p.), 2006/42/EG (після 29.12.2009 p.).

ШУМ/ВІБРАЦІЯ Зміряний відповідно до EN 60 745 рівень тиску звуку даного інструменту 93 дБ(А) i потужність звуку

104 дБ(А) (стандартне відхилення: 3 дБ), i вібрація < 2,5 м/с

(ручна методика; похибка K = 1,5 м/с

Технічні документи в: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE ∆ΗΛΩΣΗ ΣYMBATOTΗΤΑΣ ∆ηλώνυµε υπευθύνως τι τ πρϊν αυτ είναι κατασκευασµέν σύµ%ωνα µε τυς ε&ής

καννισµύς ή κατασκευαστικές συστάσεις: EN 60 745, EN 55 014, κατά τις διατά&εις των καννισµών της Κινής Αγράς

2006/95/EK, 2004/108/EK, 98/37/EK (έως 28.12.2009), 2006/42/EK (απ 29.12.2009).

ΘΡYΒ/ΚΡΑ∆ΑΣΜYΣ Μετρηµένη σύµ%ωνα µε EN 60 745 η στάθµη ακυστικής πίεσης αυτύ τυ εργαλείυ ανέρ>εται

σε 93 dB(A) και η στάθµη η>ητικής ισ>ύoς σε 104 dB(A) (κινή απκλιση: 3 dB), και  κραδασµς σε < 2,5 m/s

(µεθδς

>ειρς/@ρα>ίνα - ανασ%άλεια K = 1,5 m/s

Τενικς άκελς απ: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

OÂWIADCZENIE ZGODNOÂCI CE Niniejszym oÊwiadczamy ponoszàc osobistà odpowiedzialnoÊç, ˝e produkt wykonany jest

zgodnie z nast´pujàcymi normami i dokumentami normalizujàcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 2006/95/EU,

2004/108/EU, 98/37/EU (do 28.12.2009), 2006/42/EU (od 29.12.2009).

HA¸ASU/WIBRACJE Pomiarów dokonano zgodnie z normà EN 60 745 ciÊnienie akustyczne narz´dzia wynosi 93 dB(A) zaÊ poziom

mocy akustycznej 104 dB(A) (poziom odchylenie: 3 dB), zaÊ wibracje < 2,5 m/s

(metoda d∏oƒ-r´ka; b∏àd pomiaru K = 1,5 m/s

Dokumentacja techniczna: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE DECLARAÇÃO DE CONFIRMIDADE Declaramos sob nossa exclusiva responsabilidade que este producto cumpre as

seguintes normas ou documentos normativos: EN 60 745, EN 55 014, conforme as disposições das directivas 2006/95/CE,

2004/108/CE, 98/37/CE (até 28.12.2009), 2006/42/CE (a partir de 29.12.2009).

RUÍDO/VIBRAÇÕES Medido segundo EN 60 745 o nível de pressão acústica desta ferramenta é 93 dB(A) e o nível de potência

acústica 104 dB(A) (espaço de erro: 3 dB), e a vibração < 2,5 m/s

(método braço-mão; incerteza K = 1,5 m/s

Processo técnico em: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE DICHIARAZIONE DI CONFORMITÀ Dichiaramo, assumendo la piena responsabilità di tale dichiarazione, che il prodotto è

conforme alle seguenti normative e ai relativi documenti: EN 60 745, EN 55 014 in base alle prescrizioni delle direttive 2006/95/EG,

2004/108/EG, 98/37/EG (fino al 28.12.2009), 2006/42/EG (a partire dal 29.12.2009).

RUMOROSITÀ/VIBRAZIONE Misurato in conformità al EN 60 745 il livello di pressione acustica di questo utensile è 93 dB(A) ed il livello

di potenza acustica 104 dB(A) (deviazione standard: 3 dB), e la vibrazione < 2,5 m/s

(metodo mano-braccio; incertezza K = 1,5 m/s

Fascicolo tecnico presso: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE MINÖSÉGI TANUSITVANY Teljes felelösségünk tudatában kijelentjük, hogy jelen termék a következö szabványoknak vagy

kötelezö hatósági elöírásoknak megfelel: EN 60 745, EN 55 014, a 2006/95/EK, 2004/108/EK, 98/37/EK (2009.12.28-ig), 2006/42/EK

(2009.12.29-tŒl kezdve) elöírásoknak megfelelöen.

ZAJ/REZGÉS Az EN 60 745 alapján végzett mérések szerint ezen készülék hangnyomás szintje 93 dB(A) a hangteljesítmény szintje

104 dB(A) (normál eltérés: 3 dB), a rezgésszám < 2,5 m/s

(kézre-ható érték; szórás K = 1,5 m/s

A mıszaki dokumentáció a következŒ helyen található: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE STRVZUJÍCÍ PROHLÅ◊ENÍ Potvrzujeme na odpovπdnost, Ωe tento v¥robek odpovídå nåsledujícím normåm nebo normativním

podkladüm: EN 60 745, EN 55 014, podle ustanovení smπrnic 2006/95/ES, 2004/108/ES, 98/37/ES (do 28.12.2009), 2006/42/ES (od

29.12.2009).

HLUÇNOSTI/VIBRACÍ Mπ®eno podle EN 60 745 çiní tlak hlukové vlny tohoto p®ístroje 93 dB(A) a dávka hluçnosti 104 dB(A)

(standardní odchylka: 3 dB), a vibrací < 2,5 m/s

(metoda ruka-paΩe; nepﬁesnost K = 1,5 m/s

Technická dokumentace u: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE STANDARDIZASYON BEYANI Ye¤ane sorumlu olarak, bu ürünün aﬂa¤ıdaki standartlara veya standart belgelerine uygun

oldu¤unu beyan ederiz: EN 60 745, EN 55 014, yönetmeli¤i hükümleri uyarınca 2006/95/EG, 2004/108/EG, 98/37/EG (28.12.2009

tarihine kadar), 2006/42/EG (29.12.2009 tarihinden itibaren).

GÜRÜLTÜ

T‹TREﬁIM Ölçülen EN 60 745 göre ses basıncı bu makinanın seviyesi 93 dB(A) ve çal›ﬂma s›ras›ndaki gürültü 104 dB(A)

(standart sapma: 3 dB), ve titreﬂim < 2,5 m/s

(el-kol metodu; tolerans K = 1,5 m/s

Teknik belgelerin bulundu¤u merkez: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

143

08 SKIL Europe BV A. v.d. Kloot

DECLARAØIE DE CONFORMITATE CE Declaråm pe proprie råspundere cå acest product este conform cu urmåtoarele standarde

sau documente standardizate: EN 60 745, EN 55 014, în conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pânå la

28.12.2009), 2006/42/CE (începând cu 29.12.2009).

ZGOMOT/VIBRAØII Måsurat în conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de

93 dB(A) iar nivelul de putere a sunetului 104 dB(A) (abaterea standard: 3 dB), iar nivelul vibraøiilor < 2,5 m/s

(metoda mînå - braø;

incertitudine K = 1,5 m/s

Documentaøie tehnicå la: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE ДЕKЛАPAЦИЯ ЗA CБOTВETCTBИE Декларираме на изцяло наша отговорност, че това изделие е съобразено със

следните стандарти или стандартизирани документи: EN 60 745, EN 55 014, в съответствие с нормативната уредба на

2006/95/EG, 2004/108/EG, 98/37/EG (до 28.12.2009), 2006/42/EG (от 29.12.2009).

ШУМ/ВИБPAЦИИ Измерено в съответствие с EN 60 745 нивото на звуково налягане на този инструмент е 93 dB(A) а

нивото на звукова мощност е 104 dB(A) (стандартно отклонение: 3 dB), а вибрациите са < 2,5 m/s

(метод ръка-рамо;

неопределеност K = 1,5 m/s

Подробни технически описания при: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE IZJAVA O USKLA ĐENOSTI Izjavljujemo uz punu odgovornost da je ovaj proizvod usklađen sa slijedeçim normama i

normativnim dokumentima: EN 60 745, EN 55 014, prema odredbama smjernica 2006/95/EG, 2004/108/EG, 98/37/EG (do

28.12.2009), 2006/42/EG (od 29.12.2009).

BUCI/ VIBRACIJAMA Mjereno prema EN 60 745, prag zvuãnog tlaka ovog elektriãnog alata iznosi 93 dB(A) a jakost zvuka

104 dB(A) (standardna devijacija: 3 dB), a vibracija < 2,5 m/s

(postupkom na ‰aci-ruci; nesigurnost K = 1,5 m/s

Tehniãka dokumentacija se moÏe dobiti kod: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE IZJAVA O USKLA ĐENOSTI Pod punom odgovorno‰çu izjavljujemo da je ovaj proizvod usklađen sa sledeçim standardima ili

standardizovanim dokumentima: EN 60 745, EN 55 014, u skladu sa odredbama smernica 2006/95/EG, 2004/108/EG, 98/37/EG (do

28.12.2009), 2006/42/EG (od 29.12.2009).

BUKA/VIBRACIJE Mereno u skladu sa EN 60 745, nivo pritiska zvuka ovog alata iznosi 93 dB(A), a jaãina zvuka 104 dB(A)

(normalno odstupanje: 3 dB), a vibracija < 2,5 m/s

(mereno metodom na ‰aci-ruci; nesigurnost K = 1,5 m/s

Tehniãka dokumentacija kod: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

SRB

IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti:

EN 60 745, EN 55 014, v skladu s predpisi navodil 2006/95/ES, 2004/108/ES, 98/37/ES (do 28.12.2009), 2006/42/ES (od 29.12.2009).

HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 60 745 je raven zvoãnega pritiska za to orodje 93 dB(A) in jakosti zvoka

104 dB(A) (standarden odmik: 3 dB), in vibracija < 2,5 m/s

(metoda ‘dlan-roka’; netoãnost K = 1,5 m/s

Tehniãna dokumentacija se nahaja pri: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

SLO

CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab järgmistele standarditele või

normdokumentidele: EN 60 745, EN 55 014 vastavalt direktiivide 2006/95/EÜ, 2004/108/EÜ, 98/37/EÜ (kuni 28.12.2009),

2006/42/EÜ (alates 29.12.2009) nõuetele.

MÜRA/VIBRATSIOON Vastavalt kooskõlas normiga EN 60 745 läbi viidud mõõtmistele on antud seadme helirõhk 93 dB(A) ja

helitugevus 104 dB(A) (standardkõrvalekalle: 3 dB), ja vibratsioon < 2,5 m/s

(käe-randme-meetod; mõõtemääramatus K = 1,5 m/s

Tehniline toimik saadaval aadressil: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

EST

CE DEKLARÅCIJA PAR ATBILST±BU STANDARTIEM Mïs ar pilnu atbild¥bu pazi¿ojam, ka ‰is izstrÇdÇjums atbilst standartiem vai

standartizÇcijas dokumentiem EN 60 745, EN 55 014 un ir saska¿Ç ar direkt¥vÇm 2006/95/ES, 2004/108/ES, 98/37/ES (l¥dz

28.12.2009) un 2006/42/ES (no 29.12.2009).

TROKSNIS/VIBRÅCIJA Saska¿Ç ar standartu EN 60 745 noteiktais instrumenta rad¥tÇ trok‰¿a ska¿as spiediena l¥menis ir 93 dB(A)

un ska¿as jaudas l¥menis ir 104 dB (A) (pie tipiskÇs izkliedes: 3 dB), un vibrÇcijas intensitÇte ir < 2,5 m/s

(strÇdÇjot rokas reÏ¥mÇ;

izkliede K = 1,5 m/s

TehniskÇ lieta no: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE ATITIKTIES DEKLARACIJA Mes atsakingai parei‰kiame, kad ‰is gaminys atitinka tokius standartus ir normatyvinius

dokumentus: EN 60 745, EN 55 014 pagal reglament˜ 2006/95/EB, 2004/108/EB, 98/37/EB (iki 2009-12-28), 2006/42/EB

(nuo 2009-12-29) nuostatas.

TRIUK·MINGUMAS/VIBRACIJA ·io prietaiso triuk‰mingumas buvo i‰matuotas pagal EN 60 745 reikalavimus keliamo triuk‰mo

garso slògio lygis siekia 93 dB(A) ir akustinio galingumo lygis 104 dB(A) (standartinis nuokrypis: 3 dB), ir vibracijos pagreitis rankos

pla‰takos srityje tipiniu atveju yra maÏesnis, kaip < 2,5 m/s

(paklaida K = 1,5 m/s

Techninò byla laikoma: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

CE PREHLÁSENIE O ZHODE Vÿhradne na na√u vlastnú zodpovednos† prehlasujeme, Ωe tento vÿrobok zodpovedá nasledujúcim

normám alebo normovanÿm dokumentom: EN 60 745, EN 55 014, v súlade s predpismi 2006/95/EG, 2004/108/EG, 98/37/EG (do

28.12.2009), 2006/42/EG (od 29.12.2009).

HLUKU/VIBRÁCIÁCH Merané pod¬a EN 60 745 je úroveµ akustického tlaku tohto nástroja 93 dB(A) a úroveµ akustického vÿkonu je

104 dB(A) (√tandardná odch¥lka: 3 dB), a vibrácie sú < 2,5 m/s

(metóda ruka - paΩa; nepresnosÈ K = 1,5 m/s

Súbor technickej dokumentácie sa nachádzajú na adrese: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

Skil 5003 Instructions Manual

Marque: Skil

Modèle: 5003

Catégorie: Outils électroportatifs

Taper: Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Skil 5003

Skil 5003 Instructions Manual

Ce manuel convient également à

Skil 5003 Instructions Manual

dans d''autres langues

Documents connexes

Autres documents