Hitachi CC 14SC Instruction Manual And Safety Instructions

Marque: Hitachi

Modèle: CC 14SC

Catégorie: Outils électroportatifs

Taper: Instruction Manual And Safety Instructions

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual before operating the power tool. Please keep this manual

available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual antes de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de que utilicen la herramienta eléctrica.

MODEL CUT-OFF MACHINE

MODÈLE TRONÇONNEUSE

MODELO TRONZADORA

CC 14SC

English

Page

IMPORTANT INFORMATION ....................................... 3

MEANINGS OF SIGNAL WORDS ................................ 3

SAFETY ............................................................................ 3

FOREWORD .................................................................... 6

PART NAMES ................................................................. 7

SPECIFICATIONS ........................................................... 8

STANDARD ACCESSORIES .......................................... 8

Page

PREPARATION BEFORE OPERATION ......................... 8

BEFORE USING ............................................................ 10

PRACTICAL APPLICATIONS ...................................... 11

CUT-OFF WHEEL DISMOUNTING AND

MOUNTING ......................................................... 13

MAINTENANCE AND INSPECTION ......................... 14

SERVICE AND REPAIRS .............................................. 15

PARTS LIST ................................................................... 44

Page

INFORMATION IMPORTANTE ................................... 16

SIGNIFICATION DES TERMES DE

SIGNALISATION ................................................. 16

SÉCURITÉ ...................................................................... 16

AVANT-PROPOS .......................................................... 19

NOM DES PIÈCES ........................................................ 20

SPÉCIFICATIONS ......................................................... 21

ACCESSOIRES STANDARD ........................................ 21

Page

PRÉPARATION AVANT L’UTILISATION .................... 21

AVANT L’UTILISATION................................................ 23

APPLICATIONS PRATIQUES ...................................... 24

INSTALLATION ET RETRAIT DU DISQUE

À TRONÇONNER ................................................ 26

ENTRETIEN ET INSPECTION ..................................... 27

SERVICE APRÀS-VENTE ET RÉPARATIONS ........... 28

Página

INFORMACIÓN IMPORTANTE................................... 29

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN .................................................. 29

SEGURIDAD .................................................................. 29

PROLOGO ...................................................................... 32

NOMENCLATURA ........................................................ 33

ESPECIFICACIONES .................................................... 34

ACCESORIOS ESTÁNDAR .......................................... 34

Página

PREPARATIVOS PREVIOS A LA OPERACIÓN ......... 34

ANTES DEL USO .......................................................... 36

APLICACIONES PRÁCTICAS ..................................... 37

DESMONTAJE Y MONTAJE DE LA RUEDA

DE RECORTAR ..................................................... 39

MANTENIMIENTO E INSPECCIÓN........................... 40

SERVICIO Y REPARACIONES ..................................... 41

English

Français

Español

CONTENTS

TABLE DES MATIERES

ÍNDICE

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warnings in the Manual before

operating or maintaining this power tool.

Most accidents that result from tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on

the tool and in this Manual.

Never use this tool in a manner that has not been specifically recommended by HITACHI, unless you first

confirm that the planned use will be safe for you and others.

MEANINGS OF SIGNAL WORDS

WARNING: Indicates a potentially hazardous situations which, if ignored, could result in serious personal

injury.

CAUTION: Indicates a hazardous situations which, if ignored, could result in moderate personal injury, or

could cause machine damage.

NOTE: emphasizes essential information.

SAFETY

SAFETY RULES FOR POWER TOOLS.

READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL

BEFORE OPERATING OR MAINTAINING THIS TOOL:

WARNING: When using this electric tool, take all necessary precautions to minimize the risk of electric

shock or other personal injury.

In particular, always comply with the following safety rules:

1. ALWAYS KEEP GUARDS IN PLACE and in working order.

2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING TOOL.

Always confirm that all keys and adjusting wrenches have been removed from the tool before it is turned

on.

3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering the work areas and work

benches.

4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use power tools in damp or wet

places, and never expose them to rain. Always keep the work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

7. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the rate for which

it was designed.

8. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for which it was

not designed.

9. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL. Never wear loose

clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in the moving parts.

Always wear non-slip footwear, preferably with steel toes. Wear protective hair covering to contain long

hair.

English

10. ALWAYS USE EYE PROTECTION WHEN WORKING WITH THE TOOL, TO PREVENT EYE

INJURY. Ordinary eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also, use

a face mask for additional safety, and wear a dust mask if the cutting operation produces dust.

11. ALWAYS SECURE THE WORKPIECE TO THE VISE OR THE BASE. Use clamps or a vise to

hold the workpiece in place. It’s safer than using your hand, and it frees both hands to operate the tool.

12. NEVER OVERREACH. Always keep proper footing and balance when working with the tool.

13. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for best and safest

performance. Always follow instructions for lubricating the tool and for changing accessories.

14. ALWAYS DISCONNECT THE TOOL before servicing and before changing cut-off wheels or other

accessories.

15. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always

confirm that the switch is in the “OFF” position before inserting the power plug into the receptacle.

16. ALWAYS USE RECOMMENDED ACCESSORIES ONLY, WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories. To avoid personal

injuries, use only recommended accessories in conjunction with this tool.

17. NEVER STAND ON TOOL. Prevent serious injury by not tipping the tool and by not risking

unintentional contact with the cut-off wheel.

18. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING TOOL. Always check the guard

and all other components for damage before using the tool, to assure that they will function properly.

Check all moving parts for proper alignment, freedom from binding and other conditions that might affect

proper operation. Always repair or replace any damaged guards or other damaged components before

using the tool.

19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED; ALWAYS TURN THE

POWER OFF WHEN THE TOOL IS NOT IN USE. Always unplug the power cord when the tool

is not in use. Don’t leave tool until it comes to a complete stop.

20. This tool was not designed to be used for mass-production applications, and should not be used in mass-

production environments.

21. This tool is intended for residential use only.

22. When servicing this tool, use only authorized replacement parts.

23. Apply AC 115 volts only to this tool. Applying the wrong voltage could cause the POWER TOOL to operate

improperly and could cause serious personal injury or damage to the tool.

Specific Safety Rules for Use of this Power Tool

WARNING: The following specific operating instructions must be observed when using this POWER

TOOL, to avoid injury:

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES, TO ASSURE SAFE USE OF THIS TOOL:

1. Review this Manual and familiarize yourself with the safety rules and operating instructions for this

POWER TOOL, before attempting to use it.

2. Always confirm that the POWER TOOL is clean, before using it.

3. Always wear snug-fitting clothing, non-skid footwear (preferably with steel toes) and eye protection,

when operating the POWER TOOL.

4. Always handle the POWER TOOL carefully. If the POWER TOOL is dropped or struck against a hard object,

it might become deformed or cracked or sustain other damage.

5. Always cease operating the tool at once, if you notice any abnormality whatsoever.

6. Always confirm that all components are mounted properly and securely, before using the tool.

7. When replacing the cut-off wheel, always confirm that the rpm rating of the new wheel is correct for use

on this tool.

8. Always shut off the power and wait for the cut-off wheel to completely stop rotating, before undertaking

any maintenance or adjustments.

English

9. Always clamp or otherwise secure the workpiece to the vise; otherwise the workpiece might be thrown

from the base and cause bodily harm.

10. Always confirm that the cut-off wheel is free from any cracks, before using the tool.

11. Always confirm that the parts which fix the cut-off wheel are not damaged.

Damaged parts cause the breakage of the cut-off wheel.

12. Always make a trial run first, before attempting any new use of the tool.

13. Always use only the peripheral surface of the cut-off wheel.

14. Always handle the cut-off wheel with care, when dismounting and mounting it.

15. Always keep your hands out of the line of the cut-off wheel.

16. Always confirm that the safety cover are in the proper places, before using the tool.

17. Inspect the tool power cord periodically.

18. Always confirm that the proper lengths and types of extension cords are being utilized, when if needed,

before starting the tool.

19. Always confirm that the motor air vents are fully open, before using the tool.

20. Always wait until the motor has reached full speed, before starting a cut.

21. Always keep the handles dry, clean and free of oil and grease. Hold the tool firmly, when in use.

22. Always fix the motor section using the chain when carrying about the tool.

23. Always keep the cut-off wheels in a dry place, as humidity affects the strength of the cut-off wheels.

DON’Ts

NEVER VIOLATE THE FOLLOWING RULES, TO ASSURE SAFE USE THIS TOOL:

1. Never operate the POWER TOOL unless you fully understand the operating instructions contained in this

Manual.

2. Never leave the POWER TOOL, unattended, without first unplugging the power cord.

3. Never operate the POWER TOOL when you are tired, or after you have taken any medications or have

consumed any alcoholic beverages.

4. Never use the POWER TOOL for applications not specified in the Instruction Manual.

5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your hair is uncovered,

to protect against getting caught in the moving machinery.

6. Never reach around or behind the cut-off wheel.

7. Never touch any moving parts, including the cut-off wheel, while the tool is in use.

8. Never remove any safety devices or wheel guards; use of the tool without them would be hazardous.

9. Never lock the safety cover (always confirm that it slides smoothly, before using the tool).

10. Never abuse the power cord of the tool.

11. Never attempt to move a plugged-in POWER TOOL while your finger is on the starting switch.

12. Never use the POWER TOOL if the starting switch doesn’t turn on and off properly.

13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.

14. Never use the POWER TOOL near flammable liquids or gases, since sparking could cause an explosion.

15. Never clean plastic components with solvents, since the plastic may dissolve.

16. Never operate the tool unless all of the wheel guards are in place.

17. Never allow the cut-off wheel to be struck against a hard object, as it might get cracked.

18. Never twist the cut-off wheel during cutting operation.

19. Never expose hands, feet and fragile things to the grinding sparks, as the grinding sparks may harm

them.

20. Never use the lateral side of the cut-off wheel.

English

WARNING

FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE

CUT-OFF MACHINE.

1. Always wear eye protection, when using the tool.

2. Always keep hands out of the line of the cut-off wheel.

3. Never operate the tool without the guards in place.

4. Never perform any freehand operation with the tool.

5. Never reach around the cut-off wheel.

6. Always shut off the power and wait for the cut-off wheel to stop turning before adjusting or maintaining

the tool.

FOREWORD

The information contained in this manual is designed to assist you in the safe operation and maintenance of

the POWER TOOL. Some illustrations in this manual may show details or attachments that differ from those

on your own POWER TOOL.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

PART NAMES

Fig. 1

Wheel Cover

Safety Cover

Cut-off Wheel

Fig. 2

Handle

Spark Chute

Quick Vise

Lock-off Button

Shaft

Vise(B) Vise(A)

Base

Switch

Stopper Pin

Wheel Washer

Screw Handle

Chain

Motor

English

SPECIFICATIONS

Item Model CC 14SC

Type Series commutator motor

Motor Power source Single-phase AC 60Hz

Voltage 115 Volts

Full-load current 15 Amp

Type Reinforced resinoid cut-off wheel

Outside Dia. 14" (355 mm)

Cut-off Dimensions Thickness 7/64" (2.8 mm)

wheel Hole Dia. 1" (25.4 mm)

Max. working

16000 ft/min (4800 m/min)

peripheral speed

No-load speed 3200 rpm

No-load peripheral speed 12800 ft/min (3900 m/min)

Applicable workpiece materials Round bars, pipes and various types of shaped steel

90°

Max. Height 3-59/64" (100 mm) Max. Height 2-5/32" (55 mm)

Max. cutting

Max. Width 6-1/2" (165 mm) Max. Width 8 (203 mm)

dimensions

45°

Max. Height 3-59/64" (100 mm) Max. Height 2-5/32" (55 mm)

Max. Width 3-5/8" (92 mm) Max. Width 5" (127 mm)

Max. opening of vise 8" (203 mm)

Net weight 43.6 lbs. (19.8 kg)

Cord 2 conductor type cabtire cable 8 ft (2.5 m)

STANDARD ACCESSORIES

1 Cut-Off Wheel 14" × 7/64" × 1" (355 × 2.8 × 25.4 mm)

Model CC 14SC (A36RBIG) 1pc. (Code No.964975Z)

(Attached to the main body)

2 Wrench (Attached to the base)

WARNING: The use of attachment or accessories not recommended in this manual may be hazardous.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:

1. Installation

Secure the machine on a level flat surface, and keep it in a stable condition.

2. Grounding Instructions.

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock.

This power tool is equipped with an electric cord having an equipment-grounding conductor and a plug

with a grounding pin, as shown in Fig. 4. The plug must be plugged into a matching receptacle that is

properly installed and grounded in accordance with all local codes and regulations.

Do not modify the provided plug if it does not fit the receptacle.

Have a proper receptacle installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The

equipment-grounding conductor is the one with the green outer insulation (with/without yellow stripes).

If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding

conductor to a live terminal.

Check with a qualified electrician or serviceman if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is properly grounded.

Use only 3-core extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept

the tool’s plug.

Fig. 3

English

Repair or replace damaged or worn cord immediately. This power tool is intended for use on a circuit with

an receptacle similar to the one illustrated in sketch A, Fig. 4. A temporary adapter, similar to the one

illustrated in sketches B and C, may be used to connect the power tool plug to a 2-pole receptacle as

shown in sketch B in case a properly grounded receptacle is not available.

The temporary adapter should be used only until a properly grounded receptacle has been installed by

a qualified electrician. The green-colored grounding lug extending from the adapter must be connected

to a permanent ground such as a properly grounded receptacle box.

WARNING: Always connect the power tool to a grounded metal, permanent wiring system: or to

a system having an equipment-grounding conductor.

3. Extension Cord.

To use the power tool when no suitable power source is nearby, use

an extension cord of suitable size to ensure safety, and to prevent

power loss and overheating.

Determine from the accompanying table the required extension

cord wire size.

Check power cord and extension cords for loose or exposed wires

and damaged insulation, before using.

Repair or replace as needed, before using the power tool.

Use only 3-conductor type extension cords with three-prong

grounding-type plugs and 3-pole receptacles that accept the tool’s

plug.

NOTE: The lower the wire size number, the heavier the wire, and the farther it will carry current

without a voltage drop. If in doubt, use the next heavier gauge.

WARNING: Never connect this unit to an electrical power source until all operating instructions

have been read and understood.

4. Take off the chain.

As the movable part is pulled down by a chain when shipping out, slightly push the handle down and take

off the chain from the handle.

Fig. 4

Power Tool’s Plug

Grounding Pin

Adapter

Grounding Methods

Cover of grounded

receptacle Box

(A)

(B)

(C)

Ampere rating

12.1 to 16.0

(on nameplate)

Ext. cord length

Wire gauge size

A.W.G (mm

)

25 ft 14 A.W.G

(7.5 m) (2.0 mm

)

50 ft. 12 A.W.G

(15 m) (3.5 mm

)

100 ft. Not

(30.5 m) recommended

Grounding Lug

English

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same

voltage as that specified on the nameplate of the tool.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned ON,

the power tool will start suddenly and could cause a serious accident.

3. Check the cut-off wheel for visible defects.

Confirm that the cut-off wheel is free of cracks or other visible damages.

4. Confirm that the cut-off wheel is fixed securely to the power tool.

Using the supplied wrench, tighten the clamping bolt on the cut-off wheel mounting shaft to secure the

cut-off wheel.

WARNING: When the clamping bolt is loose, the cut-off wheel may be damaged when the wheel

axle starts revolving, causing a hazardous condition.

5. Check the safety covers for proper operation.

Possible accidents such as a cracked cut-off wheel is prevented by this safety cover (wheel cover).

Although it has been fully clamped at the factory prior to delivery, securely reclamp the mounting screws

for safety.

Safety cover and wheel cover are designed to protect the operator from coming into contact with the cut-

off wheel during operation of the tool.

WARNING: NEVER OPERATE THE POWER TOOL if the safety covers do not function smoothly.

6. Use cut-off wheels whose peripheral speed ratings are over the maximum working

peripheral speed.

When replacing the cut-off wheel, ensure that the replacement cut-off wheel has a designed peripheral

speed in excess of 16000 ft/min (4800m/min).

WARNING: Never use cut-off wheels whose peripheral speed ratings are under the maximum

working peripheral speed.

7. Confirm the stopper pin position.

Confirm that the stopper pin which was used for installtion and removal of the cut-off wheel has returned

to the retract position.

8. Securely fix the cutting material.

Ensure that the material is securely fastened with the vise. If it is not, a serious accident could be caused

if the material comes loose or the cut-off wheel breaks during operation.

9. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power plug fits

properly in the electrical receptacle and does not fall out after it is inserted.

Repair or replace the receptacle, if it is faulty.

10. Confirm that the tool’s cabtire power cable is not damaged.

Repair or replace the power cord if an inspection of the cabtire cable indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION

OF THE TOOL, AS FOLLOWS:

11. Trial Run.

After confirming that no one is standing in front of it, step away from the front position and start the power

tool and confirm that no operating abnormalities exist before attempting a cutting operation.

Trial run periods:

When replacing the cut-off wheel ........... Over 3 minutes.

When starting routine work ..................... Over 1 minute.

12. Inspect the rotating stability of the cut-off wheel.

For precise cutting, rotate the cut-off wheel and check for deflection to confirm that the wheel is not

noticeably unstable; otherwise vibration might occur and cause an accident.

English

Vise (B)

Vise (A)

Clutch

Screw Handle

Workpiece

material

Fig. 5 Fig. 6

Vise (B)

Vise (A)

Clutch

Screw Handle

Workpiece

material

PRACTICAL APPLICATIONS

WARNING: Never remove or install a workpiece while the cut-off wheel is rotating, to avoide personal

injury.

1. Procedure for fixing the cutting material (Fig. 5 and 6).

Quick Vise

Place the workpiece material between Vise (A) and Vise (B), raise the clutch and push the Screw Handle

to bring Vise (A) lightly into contact with the workpiece material, as shown in Fig. 5. Then, turn the clutch

down, and securely fix the workpiece material in position by turning the Screw Handle. When the cutting

job is completed, turn the Screw Handle 2 or 3 times to loosen the vise, and remove the workpiece

material, as shown in Fig. 6.

2. Switch operation.

To start and stop machine (Fig. 7 and 8).

The switch is switched on by manually pulling the trigger and cut off

by releasing the trigger to the original location.

The trigger switch lock-off button is designed to prevent inadvertent

operation of the power tool.

The trigger switch will not operate unless the lock-off button has

been pushed in.

When the trigger switch is released, the power goes off and the lock-

off button automatically returns to its original position, locking the

trigger switch.

Fig. 7

Trigger (Switch)

Lock-off Button

Handle

Fig. 8

Trigger (Switch)Lock-off Button

English

3. Cutting operation.

(1) Rotate the cut-off wheel, gently press down the handle, and bring the cut-off wheel close to the

material to be cut.

(2) When the cut-off wheel contacts the material, gently press down the handle further and start cutting.

(3) When cutting (or designated slotting) is completed, raise the handle and restore it to its original

position.

(4) At the termination of each cutting process, turn OFF the switch to stop rotation and proceed with the

subsequent cutting job.

WARNING: Confirm that the trigger switch is turned OFF and that the power plug has been

removed from the receptacle, whenever the tool is not in use.

CAUTION: Increased pressure on the handle will not increase the cutting speed.

On the contrary, too much pressure may result in overload of the motor and/or

decreased cutting efficiency.

4. Cutting at angles (Fig. 9 and 10).

The machine permits cutting at angles of 45° or 60°

Loosen the two 25/64" (10 mm) bolts on the vise (B), then set the working surface on the vise-jaw at any

angles of 0°, 30° or 45° as shown in Fig. 9.

Upon completion of setting, securely tighten the two 25/64" (10 mm) bolts, as shown in Fig. 10.

When wide material is to be cut at an angle, it should be firmly clamped by fixing a steel board like Fig.

11 to the vise (B), as shown in Fig. 11.

When setting at

an angle of 0°

When setting at

an angle of 30°

When setting at

an angle of 45°

Fig. 9

Fig. 10 Fig. 11

25/64"

(10 mm) bolt

Vise (B)

43/64"

(17 mm)

Flat hd. screw of more than

15/64" × 43/64" (6 mm × 17)

8-27/64"

(214 mm)

2-9/16" (65 mm)

1-21/32" (42 mm)

4-21/64"

(110 mm)

1-3/16"

(30 mm)

15/64"

(6 mm) nut

Vise (B)

Two holes

9/32" (7 mm)

More than 15/64" (6 mm)

Steel board

English

5. Moving the stationary vise-jaw (Fig. 12).

The vise opening is set to the back in the vise slide ditch of the base

when shipped from the factory.

In case the change of a vise opening is required, move the vise-jaw

to forward or backward to desired location, after unscrewing the

two bolts.

When the material to be cut is excessively wide, the vise can be

effectively used by repositioning the stationary side of the vise jaws.

6. Using a Metallic Block (Fig. 13).

When the cut-off wheel has a reduced outer diameter, insert between

the vise (A) and (B) a metallic block slightly smaller than the

dimension of workpiece being cut to use the cut-off wheel

economically.

CUT-OFF WHEEL DISMOUNTING AND MOUNTING

WARNING: Always turn off the trigger switch and disconnect the power plug from the receptacle

before removing or installing a wheel, to prevent accidental injury.

1. Dismounting the Cut-Off Wheel (Fig. 14, 15 and 16).

(1) Rotate the safety cover, to the up position, and support by hand, as shown in Fig. 14.

(2) Press in the stopper pin (see Fig. 15), and at the same time rotate cut-off wheel by hand until the

stopper pin engages.

(3) Using the wrench provided, loosen wheel bolt (see Fig. 16), by turning it counterclockwise and

remove wheel bolt, outside wheel washer and detach the cut-off wheel.

The vise jaws open

to 8" (203 mm)

Fig. 12

Dimension of

workpiece being cut

Vise (B)

Metallic block

Dimension of

metallic block

Vise (A)

(Should be slightly smaller than

the workpiece being cut)

Fig. 13

Fig. 14 Fig. 15 Fig. 16

Safety Cover

Wrench

Stopper Pin

Cut-off Wheel Wheel Washer

Wheel Bolt

Safety Cover

Wrench

English

21/32" (17 mm)

Wear Limit

1/4" (6 mm)

Brush Cap

Fig. 17 Fig. 18

2. Mounting the Cut-Off Wheel.

Thoroughly remove dust from the wheel washer and bolt, then mount the cut-off wheel by following the

dismounting procedures in reverse order.

CAUTION: * Confirm that the stopper pin has returned to the retract position after installing or

removing the cut-off wheel.

* Tighten the bolt so that it doesn’t come loose during operation of the cut-off wheel.

Confirm that the bolt has been properly tightened before the power tool is started.

MAINTENANCE AND INSPECTION

WARNING: Always confirm that the trigger switch is turned OFF and that the power plug has been

disconnected from the receptacle before performing any maintenance or inspection of this

tool, to avoid accidental injury.

1. Replacing a cut-off wheel.

When the cut-off wheel has already become dull by frequent use, it can cause overload to the motor.

Consequently, re-dress or replace a dull cut-off wheel to ensure cut-off efficiency.

2. Inspecting the carbon brushes (Fig. 17 and 18).

The carbon brushes in the motor are expendable parts.

If the brushes become excessively worn, motor trouble might occur.

Therefore, inspect the brushes periodically, and replace them when they have become worn to the wear

limit line, as shown in Fig. 17.

Also, keep the carbon brushes clean be so that they will slide smoothly within the brush holders. The

carbon brushes can easily be removed after disassembling the brush caps (see Fig. 18) with a slotted

(minus) screwdriver.

3. Inspecting the mounting screws.

Regularly inspect each component of the power tool for looseness.

Re-tighten mounting screws on any loose part.

WARNING: Never operate the power tool if any components are loose, to prevent personal injury.

4. Inspecting the safety cover for condition and proper operation.

Before each use of the tool, test the safety cover (see Fig. 1) to assure that it is in good condition and that

it moves smoothly.

Never use the tool unless the safety cover operates properly, and unless it is in good mechanical

condition.

5. Storage.

Confirm that the trigger switch is turned OFF, that the power plug has been removed from the receptacle

and that the lock-off button has been removed and has been stored in a secure place, after operation of

the tool has been completed.

When the tool is not in use, keep it stored in a dry place out of the reach of children.

English

6. Lubrication.

Lubricate the following sliding surfaces once a month to keep the power tool in good operating condition

for a long time (see Fig.1 and 2). Use of machine oil is recommended.

Oil supply points:

*Rotary portion of shaft.

*Rotary portion of vise.

*Rotary portion of vise-jaw.

*Quick vise.

7. Cleaning.

Periodically remove chips and other waste material from the surface of the power tool with a damp, soapy

cloth. To avoid a malfunction on the motor, protect it from contact with oil or water.

SERVICE AND REPAIRS

All quality power tools will eventually require servicing or replacement of parts because of wear from normal

use. To assure that only authorized replacement parts will be used, and that the double insulation system will

be protected, all service (other than routine maintenance) must be performed by an AUTHORIZED HITACHI

POWER TOOL REPAIR CENTER, ONLY.

NOTE: Specifications are subject to change without any obligation on the part of HITACHI.

Français

INFORMATION IMPORTANTE

Lire et bien assimiler toutes les instructions d’utilisation, consignes de sécurité et avertissements du manuel

avant d’utiliser ou d’entretenir cet outil électrique.

La plupart des accidents qui se produisent lors de l’utilisation et de l’entretien de l’outil résultent d’un non

respect des règles ou des consignes de sécurité élémentaires. Il est facile d’éviter les accidents si l’on a

conscience d’une situation potentiellement dangereuse avant qu’elle ne se produise, et en observant les

procédures de sécurité appropriées.

Les consignes de sécurité élémentaires sont données à la section “SECURITE” de ce manuel et dans les

sections qui renferment les instructions d’utilisation et d’entretien.

Les risques contre lesquels se prémunir pour éviter toute blessures physiques ou dommage matériel sont

identifiés par des AVERTISSEMENTS sur l’outil et dans le présent manuel.

Ne jamais utiliser l’outil d’une façon non spécifiquement recommandée par HITACHI, sans s’être au préalable

assuré que l’utilisation prévue est sans danger pour soi et pour les autres.

SIGNIFICATION DES TERMES DE SIGNALISATION

AVERTISSEMENT: Indique des situations potentiellement dangereuse qui, si elles sont ignorées, pourraient

entraîner de graves blessures.

PRÉCAUTION: Indique des situations dangereuse qui, si elles sont ignorées, pourrait entraîner de légères

blessures ou endo mmager l’outil.

REMARQUE: Met en reliet des informations essentielles.

SÉCURITÉ

CONSIGNES DE SÉCURITÉ RELATIVES AUX OUTILS ÉLECTRIQUES.

LIRE TOUS LES AVERTISSEMENTS ET TOUTES LES INSTRUCTIONS D’UTILISATION DU

MANUEL AVANT DE METTRE L’OUTIL EN SERVICE OU DE L’ENTRETENIR :

AVERTISSEMENT: Lorsqu’on utilise l’outil électrique, prendre toutes les précautions nécessaires

pour éviter au maximum tout risque de choc électrique ou autre blessure

physique. En particulier, toujours respecter les consignes de sécurité suivantes:

1. TOUJOURS LAISSER LES PROTECTIONS EN PLACE et les maintenir en bon ordre de marche.

2. TOUJOURS RETIRER LES CLAVETTES DE RÉGLAGE ET LES CLÉS AVANT DE METTRE

L’OUTIL EN MARCHE. Toujours vérifier que les clavettes et les clés de réglage sont bien toutes

retirées de l’outil avant de le mettre en marche.

3. TOUJOURS MAINTENIR L’AIRE DE TRAVAIL PROPRE. Pour éviter tout risque de blessure, ne

pas encombrer l’aire de travail ni l’établi.

4. NE JAMAIS UTILISER L’OUTIL DANS UN ENVIRONNEMENT DANGEREUX. Ne jamais

utiliser l’outil électrique dans un endroit humide ou mouillé, et ne jamais l’exposer à la pluie. Toujours

veiller à ce que l’aire de travail soit suffisamment éclairée.

5. NE JAMAIS LAISSER LES ENFANTS APPROCHER. Tous les visiteurs devront rester à une

distance suffisamment éloignée de l’aire de travail.

6. RENDRE L’ACCÈS DE L’AIRE DE TRAVAIL IMPOSSIBLE AUX ENFANTS|||, notamment

à l’aide de cadenas, interrupteurs maîtres, ou en retirant les clés de mise en marche.

7. NE JAMAIS FORCER SUR L’OUTIL. effectuera le travail le meilleur et avec la sécurité maximale

au régime pour lequel il a été conçu.

8. TOUJOURS UTILISER LES OUTILS APPROPRIÉS. Ne jamais utiliser un outil ou un accessoire

pour un travail pour lequel il n’est pas conçu.

Français

9. PORTER DES VÊTEMENTS APPROPRIÉS PENDANT LE TRAVAIL. Ne jamais porter de

vêtements lâches ni de gants, cravate, bagues, bracelets ni aucun autre bijou qui pourraient se coincer

dans les pièces en rotation. Toujours porter des chaussures anti-dérapantes, de préférence avec des

doigts de pied en acier. Porter un couvre-chef qui recouvre les cheveux longs.

10. TOUJOURS PORTER DES LUNETTES DE PROTECTION PENDANT LE TRAVAIL POUR

ÉVITER TOUT RISQUE DE BLESSURE DES YEUX. Les lunettes ordinaires N’assurent PAS une

protection suffisante parce que les verres ne sont pas faits en verre résistant aux chocs. Par ailleurs,

porter un masque sur le visage pour accroître la sécurité, et un masque anti-poussière si le travail doit

dégager de la poussière.

11. TOUJOURS FIXER LA PIÈCE DANS L’ÉTAU OU SUR LE SOCLE. Utiliser des dispositifs de

serrage ou un étau pour tenir la pièce. Cela sera plus sûr que de tenir la pièce à la main et libérera les deux

mains pour le travail.

12. NE JAMAIS TROP SE PENCHER. Toujours garder une bonne assise et un bon équilibre pendant

le travail.

13. TOUJOURS ENTRETENIR LES OUTILS AVEC SOIN. Toujours maintenir les outils aiguisés et

propres pour optimiser le travail et la sécurité. Toujours suivre les instructions de graissage et de

remplacement des accessoires.

14. TOUJOURS DÉBRANCHER L’OUTIL avant un entretien et lors du remplacement du disque à

tronçonner ou de tout autre accessoire.

15. NE JAMAIS RISQUER UNE MISE EN MARCHE INOPINÉE LORSQU’ON BRANCHE

L’OUTIL. Toujours vérifier que l’interrupteur est en position “OFF” avant de brancher la fiche

d’alimentation dans la prise secteur.

16. TOUJOURS UTILISER EXCLUSIVEMENT LES ACCESSOIRES RECOMMANDÉS POUR

L’OUTIL. Consulter le manuel d’instructions pour la description des outils recommandés. Pour éviter

tout risque de blessure, utiliser exclusivement les accessoires recommandés pour cet outil.

17. NE JAMAIS SE TENIR DEBOUT SUR L’OUTIL. Pour éviter tout risque de blessure grave, ne pas

toucher l’outil et éviter tout contact fortuit avec le disque à tronçonner.

18. TOUJOURS VÉRIFIER SI L’OUTIL A DES PIÈCES ENDOMMAGÉES AVANT DE L’UTILISER.

Toujours vérifier si la protection et les autres composants sont endommagés avant d’utiliser l’outil pour

s’assurer qu’ils fonctionneront correctement. Vérifier si toutes les pièces mobiles sont bien alignées, non

voilées, ou toute autre condition qui pourrait entraver leur bon fonctionnement. Toujours réparer ou

remplacer les protections ou les autres pièces endommagées avant d’utiliser l’outil.

19. NE JAMAIS S’ÉLOIGNER DE L’OUTIL QUAND IL FONCTIONNE ; TOUJOURS LE

METTRE HORS TENSION QUAND ON NE S’EN SERT PAS. Toujours débrancher le cordon

d’alimentation quand on ne se sert pas de l’outil. Ne pas s’éloigner de l’outil tant qu’il n’est pas

complètement arrêté.

20. L’outil n’est pas conçu pour des applications de fabrication en série, et il ne devra donc pas être utilisé

dans un environnement de fabrication en série.

21. L’outil est conçu exclusivement pour un usage domestique.

22. Pour les réparations, utiliser exclusivement des pièces de rechange agréées.

23. Alimenter l’outil exclusivement sur un courant alternatif de 115 volts. Une tension ou une alimentation

incorrectes pourraient provoquer un mauvais fonctionnement de l’OUTIL ELECTRIQUE et provoquer de

graves blessures physiques ou de graves dommages matériels de l’outil.

Consignes de sécurité spéciales pour cet outil électrique

AVERTISSEMENT: Pour éviter tout risque de blessure, respecter les consignes de sécurité spéciales

suivantes lors de l’utilisation de l’OUTIL ELECTRIQUE :

CHOSES À FAIRE

TOUJOURS OBSERVER LES CONSIGNES SUIVANTES POUR GARANTIR UNE UTILISATION

EN TOUTE SÉCURITÉ :

1. Bien lire le manuel et se familiariser avec les consignes de sécurité et les instructions d’utilisation de

l’OUTIL ELECTRIQUE avant de l’utiliser.

2. Toujours vérifier que l’OUTIL ELECTRIQUE est propre avant de l’utiliser.

Français

3. Toujours porter des vêtements bien ajustés et des chaussures anti-dérapantes (de préférence avec des

doigts de pied en acier) et des lunettes de protection lorsqu’on utilise l’OUTIL ELECTRIQUE.

4. Toujours manier l’OUTIL ELECTRIQUE avec soin. Si l’OUTIL ELECTRIQUE tombe ou qu’il heurte un objet

dur, il risque de se déformer, de se fendiller ou autre dommage.

5. Toujours cesser immédiatement d’utiliser l’outil si l’on remarque quelque chose d’anormal.

6. Toujours vérifier que les pièces sont toutes correctement montées et fixées avant d’utiliser l’outil.

7. Pour le remplacement du disque à tronçonner, toujours vérifier que le régime nominal du nouveau

disque convient pour l’outil.

8. Toujours mettre l’outil hors tension et attendre que le disque à tronçonner ait complètement cessé de

tourner avant tout entretien ou tout réglage.

9. Toujours visser ou fixer la pièce dans l’étau, pour qu’elle ne risque pas d’être éjectée du socle et de

provoquer des blessures.

10. Toujours vérifier que le disque à tronçonner n’est pas fissuré avant d’utiliser l’outil.

11. Toujours vérifier que les pièces qui fixent le disque à tronçonner ne sont pas fissurées avant d’utiliser

l’outil. Des pièces endommagées pourraient provoquer une rupture du disque.

12. Toujours faire un essai avant d’utiliser l’outil pour un nouvel usage.

13. Toujours utiliser uniquement la surface périphérique du disque à tronçonner.

14. Toujours manipuler le disque à tronçonner avec soin lorsqu’on le démonte ou qu’on le monte.

15. Toujours éloigner les mains du trajet de lame.

16. Toujours vérifier que le carter de sécurité est en place avant d’utiliser l’outil.

17. Inspecter périodiquement le cordon d’alimentation.

18. Le cas échéant, toujours vérifier que l’on utilise des cordons et des rallonges du type et de la longueur

voulus avant de mettre l’outil en marche.

19. Toujours vérifier que les évents d’aération du moteur sont complètement dégagés avant d’utiliser l’outil.

20. Toujours attendre que le moteur ait atteint sa vitesse de régime avant d’entamer une coupe.

21. Toujours maintenir les poignées sèches, propres et sans huile ni graisse. Tenir l’outil fermement pendant

le travail.

22. Toujours fixer la section du moteur avec une chaîne pour transporter l’outil.

23. Toujours ranger les disques à tronçonner dans un endroit sec, car l’humidité aura un effet néfaste sur la

résistance des disques à tronçonner.

CHOSES A NE PAS FAIRE

POUR GARANTIR UNE UTILISATION EN TOUTE SÉCURITÉ, NE JAMAIS VIOLER LES

CONSIGNES SUIVANTES :

1. Ne jamais utiliser l’OUTIL ELECTRIQUE si l’on ne comprend pas bien les instructions de ce manuel.

2. Ne jamais s’éloigner de l’OUTIL ELECTRIQUE sans débrancher auparavant son cordon d’alimentation.

3. Ne jamais utiliser l’OUTIL ELECTRIQUE quand on est fatigué, après avoir pris des médicaments ou

consommé des boissons alcoolisées.

4. Ne jamais utiliser l’OUTIL ELECTRIQUE pour des applications non spécifiées dans ce manuel d’instructions.

5. Ne jamais faire fonctionner l’outil si l’on porte des vêtements lâches, une cravate ou des bijoux, ou sans

se couvrir les cheveux, pour éviter qu’ils ne se prennent dans les pièces mobiles.

6. Ne jamais passer les mains autour ou derrière le disque à tronçonner.

7. Ne jamais toucher les pièces en mouvement, y compris le disque à tronçonner, pendant le fonctionnement

de l’outil.

8. Ne jamais retirer les dispositifs de sécurité ni les protections de lame ; l’utilisation de l’outil serait

dangereuse sans ces pièces.

9. Ne jamais verrouiller le carter de sécurité (toujours vérifier qu’il glisse régulièrement avant d’utiliser

l’outil).

10. Ne jamais endommager le cordon d’alimentation de l’outil.

Français

11. Quand l’OUTIL ELECTRIQUE est branché, ne jamais tenter de le déplacer avec le doigt sur l’interrupteur

de marche.

12. Ne jamais utiliser l’OUTIL ELECTRIQUE si l’interrupteur de marche ne fonctionne pas correctement.

13. Ne jamais utiliser l’OUTIL ELECTRIQUE si le logement en plastique ou la poignée sont déformés ou

fendillés.

14. Ne jamais utiliser l’OUTIL ELECTRIQUE à proximité de liquides ou de gaz inflammables, car les étincelles

pourraient provoquer une explosion.

15. Ne jamais nettoyer les composants en plastique avec des solvants car cela risquerait de dissoudre le

plastique.

16. Ne jamais faire fonctionner l’outil si les protections de lame ne sont pas toutes en place.

17. Ne jamais laisser le disque à tronçonner heurter un objet dur car il pourrait se fendre.

18. Ne jamais faire subir de mouvement de torsion au disque à tronçonner pendant le fonctionnement.

19. Ne jamais exposer les mains, les pieds ni des objets fragiles aux étincelles du meulage, car ces étincelles

pourraient les endommager.

20. Ne jamais utiliser le côté latéral du disque à tronçonner.

AVERTISSEMENT

POUR VOTRE PROPRE SÉCURITÉ, LISEZ ATTENTIVEMENT CE MANUEL D’INSTRUCTIONS

AVANT D’UTILISER LA TRONÇONNEUSE.

1. Toujours porter des lunettes de protection lorsqu’on utilise l’outil.

2. Toujours éloigner les mains du trajet de lame.

3. Ne jamais faire fonctionner l’outil si les protections ne sont pas en place.

4. Ne jamais effectuer d’opération à la volée avec l’outil.

5. Ne jamais passer la main autour du disque à tronçonner.

6. Toujours mettre l’outil hors tension et attendre que le disque ait complètement cessé de tourner avant

de régler ou d’entretenir l’outil.

AVANT-PROPOS

Les informations contenues dans ce manuel sont destinées à vous aider à utiliser et à entretenir l’OUTIL

ELECTRIQUE en toute sécurité. Certaines illustrations de ce manuel peuvent montrer des détails ou des

fixations qui diffèrent de ceux de votre OUTIL ELECTRIQUE.

CONSERVER CES IINSTRUCTIONS

LES METTRE A LA DISPOSITION

DES AUTRES UTILISATEURS

DE L’OUTIL!

Français

NOM DES PIÈCES

Fig. 1

Carter de lame

Carter de sécurité

Disque à tronçonner

Fig. 2

Poignée

Evacuateur d’étincelles

Etau rapide

Bouton de sécurité

Arbre

Etau (B) Etau (A)

Socle

Gâchette

Butée goupille

Rondelle de disque

Poignée à vis

Chaîne

Moteur

La page charge ...

Hitachi CC 14SC Instruction Manual And Safety Instructions

Marque: Hitachi

Modèle: CC 14SC

Catégorie: Outils électroportatifs

Taper: Instruction Manual And Safety Instructions

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi CC 14SC
español: Hitachi CC 14SC

Hitachi CC 14SC Instruction Manual And Safety Instructions

Hitachi CC 14SC Instruction Manual And Safety Instructions

dans d''autres langues

Documents connexes

Autres documents