Magtek DynaMAX Quick Installation Guide

Taper
Quick Installation Guide
DynaMAX
Secure Card Reader Authenticator
Quick Installation Guide
www.magtek.com
DynaMAX, MagTek’s newest secure card reader authenticator, gives users the exibility
needed in point of sale and point of service environments. Whether used by a bank, hotel,
retail merchant, food truck, or theatre, DynaMAX’s ability to work with USB wired or a
wireless connection delivers one reader for mobile or stationary needs, saving the user
money on a single, low-cost, yet highly secure device.
Product Description
MSR swipe path
Lanyard mount point
Power on/off switch
General status LED
USB connection
Battery compartment (underneath)
Bluetooth status LED
Contents/Pre-Installation Checklist
Figure 2. Product Diagram
Drawings
Figure 1. Contents
MICRO USB B PLUG
CON 1 CON 2
micro-USB connection
USB connection
Batteries included. Requires 2 “AA” batteries or USB connection.
DynaMAX SCRA
micro-USB cable
Wireless status LED
Connection and Mounting
Compatibility and Operating System
Power
www.magtek.com
Slide the power switch to the right to turn ON. Slide left to turn OFF.
Mobile powered by two (2) Alkaline “AA” batteries. Users have the freedom
to operate eDynamo as a wireless device while taking payments on the go. Battery
standby time is 5 years; 3 VDC on battery power; Max current draw is < 100mA.
To install batteries: Use your nger to squeeze the release tab on the battery cover,
and remove the battery cover. Remove used batteries if they are already installed,
and dispose of them according to local e-waste guidelines.Insert the new batteries,
making sure to orient each battery to the plus and minus signs stamped inside the
battery compartment. Re-attach the battery cover and snap it closed.
Counter top powered by USB via Micro-USB B jack. Use the USB interface and
power to operate while connected to a PC or tablet-based POS system where a USB
host and power are available. Voltage is 5 VDC; Max current draw is < 100mA.
iOS 7.1; Android 4.4.2; USB: Windows 7, Windows 8;
Wireless: Windows 8.1 on hosts with wireless hardware
Mounting Options: Desktop anti-skid pad, attached weight, threaded mounting
holes and optional recessed cable, and adhesive and optional recessed cable, and
Hook-and-Loop fasteners, and Lanyard.
USB HID: Make sure the host and device are powered off. Connect the small end
of the USB cable to DynaMAX. The Micro USB connector can be swiveled to orient
vertically for connections through the mounting surface, or horizontally for other types
of cable run. Connect the large end of the USB cable to the host computer’s USB
port. Power on the host computer. Power on the device using the power switch. On
the host, install and congure the software to be used with DynaMAX (USB HID).
Wireless - Mobile wireless mode requires batteries: To use a wireless
connection, the device must be powered by two alkaline “AA” batteries. Install
batteries and switch ON power. If the device is waiting to pair, it should ash the
wireless status LED for up to 60 seconds. Otherwise you may test the batteries by
swiping a card and making sure the LEDs ash. On the mobile device, go to Settings
and enable wireless connection. Scan for devices, and select the DynaMAX you want
to pair to. Note: you will see the DynaMAX and its serial number. When prompted,
enter factory default passcode 000000 (or the device’s actual password if it has been
congured differently). On the mobile device, install and congure the software you
intend to use with DynaMAX.
Compliance
FCC WARNING STATEMENT: This equipment has been tested and was found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation.
FCC COMPLIANCE STATEMENT: This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
CANADIAN DOC STATEMENT: This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans
le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE STANDARDS: Testing for compliance with CE requirements was performed by an independent laboratory.
The unit under test was found compliant with standards established for Class B devices.
UL/CSA: This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
RoHS STATEMENT: When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous Substances
(RoHS) European Directive 2002/95/EC. The marking is clearly recognizable, either as written words like “Pb-free”, “lead-free”, or as another clear symbol ( ).
Pb
Registered to ISO 9001:2000 © Copyright 2016 MagTek, Inc. PN D998200048 rev 40 5/16
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740
p 562-546-6400 | f 562-546-6301 | 800-788-6835 | www.magtek.com
Power LED (Blue); Three-color General Status LED (Red/Green/Amber)
LEDs
Technical Support
When calling the support team please have your reader charged and have the part
number and serial number(s) available.
651.415.6800
COLOR FLASHING PATTERN MEANING
OFF OFF If connected to USB, device is powered off, or the host has put
the device into suspend mode, or a card has just been swiped.
If powered by batteries, the device is waiting for a swipe, or
device is powered off, or batteries need to be replaced.
GREEN
GREEN-
GreeGREEN
OFF
STEADY ON If congured to require authentication, device is waiting
for authentication. After authentication is established it
will slowly blink green, or will turn steady red if authentica-
tion fails. Otherwise, device is ready to read a card.
GREEN TWO SECONDS ON Device has successfully read a swiped card.
GREEN SLOW BLINKING If congured to require authentication, authentication has
been established, device is ready to read a card.
GREEN RAPID FLASHING If operating in wireless mode, reader has card data to send to
the host, but does not yet have a wireless data connection to
the host. Flashing will stop when connection is established
or after timeout waiting for connection (15-30 seconds).
AMBER STEADY ON Device is powered by USB and is waiting for the
host to establish a USB data connection.
AMBER TWO SECONDS ON If operating in wireless mode, reader has card data
to send to the host, but sending has failed.
RED STEADY ON If congured to require authentication, authentication has failed.
Attempt to re-authenticate, or power off the device, check
authentication conguration, and power the device back on.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Magtek DynaMAX Quick Installation Guide

Taper
Quick Installation Guide

dans d''autres langues