Magtek Bullet Quick Installation Guide

Marque: Magtek

Modèle: Bullet

Catégorie: Lecteurs de cartes

Taper: Quick Installation Guide

BulleT (SPP

and KB

)

Secure Card Reader Authenticator

Quick Installation Guide

www.magtek.com

Security anywhere. With the BulleT Secure Card Reader Authenticator (SCRA),

security comes with the exibility and portability of a wireless connection. Small

enough to t into the palm of your hand, the BulleT enables secure wireless

communications with a PC or mobile phone using a popular wireless interface. Not

only does the BulleT encrypt card data from the moment the card is swiped, but it

also enables card authentication to immediately detect counterfeit or altered cards.

* BulleT SPP (serial port prole) is designed for Android and Windows OS where

Serial Port Prole is supported.

** BulleT KB (wireless keyboard) is designed for computing devices connected to

wireless keyboard. (iOS, Android, Windows and Mac OS)

Product Description

Diagram

Specications

Figure 1. Contents

The power switch is located on the front of the reader.

Press to turn on (default is 120 seconds).

Hold 1 second to extend on.

Hold 3 seconds to turn off.

Power Switch

LED Indicator (Charging)

Connection: Wireless or USB

Interface: Wireless (USB is used for charging the battery)

Power: Battery powered; battery is charged from a 5V source, e.g.,

USB bus

Card Speed: 4 to 60 ips

Electrical Current: 100mA maximum during charge

Operating Temp: 32°F - 113°F ( 0 - 45°C)

Operating Humidity: 10% to 90% noncondensing

Accessories: Optional stylus is available

MICRO USB B PLUG

CON 1 CON 2

Figure 2. micro-USB cable

micro-USB connection USB connection

Additional Contents

Magstripe swipe path

Connection

Compatibility and Operating System

Power and Charging

www.magtek.com

Charge: Attach the USB cable. It takes approximately 2.5 hours to fully charge the

battery and it will stay charged for approximately 100 card swipes. The LED will

slowly blink amber while the battery is charging and then turn solid amber when the

battery is fully charged (for best results, allow the battery to fully charge).

Power USB HID connection: Insert the Micro-B end of the cable into Micro-B port on

the bottom of the reader and the Standard-A connector into a USB port on the PC/

Mac. USB connection will automatically detect your device.

Mobile: BulleT KB/SPP Connection

1. Pull up Applications or Menu and select Settings.

2. Select wireless and network.

3. Select wireless settings.

4. Turn on the BulleT reader, (green light will ash while connecting.)

5. Select Scan for devices.

6. Select the MAGTEK-xxxx device when it appears on the screen.

7. The screen will prompt you for a PIN (the default is 1234).

8. BulleT KB device is paired and ready to use.

BulleT SPP device requires you to go to the application.

Follow the application screen prompts to connect to wireless device.

After it is connected, the device is ready to use.

Personal Computer (PC): BulleT KB/SPP Connection

1. If prompted for a passkey use 1234.

2. Attach a wireless adapter to the PC.

3. Select wireless icon in Control Panel.

4. Click Add.

5. Check My device is set up and ready to be found.

6. Then click Next.

7. Select the MAGTEK-xxxx device (number indicated on the reader).

8. Then click Next.

9. Select Let me choose my own passkey.

10. Then type “1234” in the associated box.

11. Click Next when ready. Wait for the device to be installed.

13. After the device is installed, note the Outgoing COM port (if using BulleT SPP): for

communication purposes. If using BulleT KB, it will interact with the connected PC as a wireless

Keyboard.

14. Click Finish. The BulleT reader is now ready to use.

NOTE: UNINSTALL ANY EXISTING WIRELESS SOFTWARE PRIOR TO BEGINNING

INSTALLATION. DO NOT PLUG USB ADAPTER IN UNTIL INSTRUCTED TO DO SO.

Insert the Micro-B end of the cable into Micro-B port on the bottom of the reader and

the Standard-A connector into a USB port on the PC/Mac.

Compliance

FCC WARNING STATEMENT: This equipment has been tested and was found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur

in a particular installation.

FCC COMPLIANCE STATEMENT: This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CANADIAN DOC STATEMENT: This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.

CE STANDARDS: Testing for compliance with CE requirements was performed by an independent laboratory.

The unit under test was found compliant with standards established for Class B devices.

UL/CSA: This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.

RoHS STATEMENT: When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous Substances (RoHS) European Directive 2002/95/

EC. The marking is clearly recognizable, either as written words like “Pb-free”, “lead-free”, or as another clear symbol ( ).

MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740 p 562-546-6400 | f 562-546-6301 | 800-788-6835 | www.magtek.com

LEDs

Technical Support

When calling the support team please have your reader charged and have the part

number and serial number(s) available.

[email protected]

651.415.6800

LED Color LED Condition USB

Connection

Meaning

Off n/a No power