This document provides information about using the MagTek®
Dynamag Duo secure card reader authenticator that is driven by
your application. For detailed information and device manuals,
please visit MagTek support: www.magtek.com/support.
Product Description
MagTek’s Dynamag Duo, a secure card reader authenticator
(SCRA), is a compact magnetic stripe card reader that conforms
to ISO standards. In addition to reading multiple tracks of data
from either side of a card, the device also includes MagnePrint
technology. The devices are compatible with any host with a USB
interface. Cardholders can swipe their cards in either direction,
facing either way.
Major Components
Connection and Power
The USB cable provides the device with power and bidirectional
communication with a USB-capable host.
On hosts with the Windows operating system, the rst time the
reader is plugged into a specic USB port, Windows will pop up a
dialog box, which will guide you through the process of installing
a device driver for the reader. Be certain to install the device driver.
Dynamag Duo can be operated in two different modes:
• HID and
• HID with Keyboard Emulation
When set to Keyboard Emulation (KB) mode, the device emulates
a USB HID United States keyboard by default, or can be
congured to use any international keyboard mapping using ALT
ASCII code keypad key combinations or customizable key maps.
This allows host software designed to acquire card data from
keyboard input to seamlessly acquire card data from the device.
Mounting
The device is designed to be mounted to a xed surface. Ensure
the Reader is positioned on a at, accessible surface with at least 4
inches clearance on either end for room to swipe a card. Mounting
may or may not include washers or a gasket, depending on solution
requirements. Dynamag Duo may be mounted with screws or
fastening tape as described below:
• Mounted to a custom, solution-specic mounting plate or
at surface using two screws through the surface attached
to the bottom of the device. Drill a hole in the surface for the
cable, and run the cable through the hole. Hand screw to
the device ONLY and use no more than 4.75 in lbs.
torque. Make certain to ONLY use screws included or
equivalent.
• Fastened with tape on the surface and running the cable
on the top of the surface. If fastening tape is to be used,
clean the area that Dynamag Duo will be mounted on with
Isopropyl alcohol. Remove the adhesive protective cover of
the fastening tape, then position the reader and push down
rmly. Mount the Reader.
Caution: When in Keyboard Emulation mode, if another
keyboard is connected to the same host as the reader and a key
is pressed on the other keyboard while the reader is transmitting,
then the data transmitted by the reader may be corrupted.
Caution: To avoid damaging the read head, only clean the card
path with approved cleaning cards. DO NOT use liquid cleaning
products or insert any other objects into the device.
Dynamag Duo
Dual Head Secure Card Reader Authenticator
Quick Installation Guide
Setup and Installation
MagTek
®
Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
When the reader is not powered, the LED will be off. When the
reader is rst plugged in, the LED will be solid amber. After the
reader is plugged in, the host will try to enumerate the reader.
Once the reader is enumerated the LED will turn solid green.
In addition to the General Status LED, the device incorporates a
buzzer. After a cardholder swipes a card, the device will emit two
short 2 kHz buzzes for a good read, or one buzz for a bad read,
prompting the cardholder to try the swipe again.
Troubleshooting
If the reader becomes unresponsive try unplugging and plugging
back in and rebooting the Host system. If you receive card read
errors, make certain you are swiping in a smooth uid path, that
there is no debris in the reader, and the card is clean. Only clean
MagTek card readers with MagTek approved card cleaning kits.
Technical Support
When contacting the support team please have power to your
reader and have the part number and serial number(s) available,
contact [email protected]
Compliance
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit than the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
CUR/UR
This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set out in
the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la classe B prescrites dans le Réglement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
CE STANDARDS
Testing for compliance with CE requirements was performed by an independent laboratory. The unit
under test was found compliant with standards established for Class B devices.
UL/CSA
This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
ROHS STATEMENT
When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE)
Reduction of Hazardous Substances (RoHS) European Directive 2002/95/EC. The marking is clearly
recognizable, either as written words like “Pb-free,” “lead-free,” or as another clear symbol ( ).
Commands
Some applications include a visual indication of whether the device
is active or not. Contact your representative to learn where you can
download your application.
Card Read
A card may be swiped through the reader slot when the LED is
solid green or ashing green. The magnetic stripe can face toward
the front of the reader (as indicated by the lock logo on the shiny
stripe) or the back of the reader and may be swiped in either
direction. If there is data encoded on the card, the reader will
attempt to read the data, encrypt it, and then send the results to the
host via a USB HID input report or, if in Keyboard Emulation mode,
as if the data was being typed on a keyboard. After the results are
sent to the host, the reader will be ready to read the next card.
Visual and Auditory Cues
The reader has one LED on the reader body. The LED indicator will
be either off, red, green, or amber.
Color Action Meaning
off off The device is not powered, or the host has put the device
into Suspend mode.
Green Steady
On
If the device is congured to require authentication, the
device is waiting for authentication. If the device is not
congured to require authentication, the device is ready to
read a card.
Green Two
Second
Blink
A cardholder has swiped a card, and the device has
successfully decoded the swiped card.
Green Slow
Blinking
If congured to require authentication, authentication has
been established, and the device is ready to read a card.
Amber Steady
On
When the device is rst turned on, the LED is solid amber
while.
Red Steady
On
If the device is congured to require authentication (Secu-
rity Level 4), authentication has failed. Make sure you are
connecting to the correct host, check the authentication
conguration on the host, and power cycle the device.
The device also uses this status when a user is updating
the rmware. On completion, the device will reset and
the LED will turn off briey.
RED Two
Seconds
On
Device has failed to decode data on a swiped card. Try the
swipe again.
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200223 rev. 10 9/19
MagTek
®
Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
Pb
Use and Compliance
-
1
-
2
dans d''autres langues
- English: Magtek Dynamag Duo User manual
Documents connexes
-
Magtek Dynamag Quick Installation Guide
-
Magtek DynaMAX Quick Installation Guide
-
-
-
-
Magtek DynaFlex Kiosk Family Quick Installation Guide
-
Magtek iDynamo Manuel utilisateur
-
Magtek Rails Technical Reference Manual
-
-