Ampro AT-6010-R Manuel utilisateur

AT-6010

Advanced Wire Tracer

User Manual

ENG FRE

SPA

English

AT-6010

Advanced Wire Tracer

User Manual

3/2019, 6011540 B

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for one year from the

date of purchase unless local laws require otherwise. This warranty does not cover fuses, disposable

batteries or damage from accident, neglect, misuse, alteration, contamination, or abnormal

conditions of operation or handling. Resellers are not authorized to extend any other warranty

on the behalf of Amprobe. To obtain service during the warranty period, return the product with

proof of purchase to an authorized Amprobe Service Center or to an Amprobe dealer or distributor.

See Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES

- WHETHER EXPRESS, IMPLIED OR STATUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER

SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow

the exclusion or limitation of an implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All Amprobe returned for warranty or non-warranty repair or for calibration should be accompanied

by the following: your name, company’s name, address, telephone number, and proof of purchase.

Additionally, please include a brief description of the problem or the service requested and include

the test leads with the meter. Non-warranty repair or replacement charges should be remitted in

the form of a check, a money order, credit card with expiration date, or a purchase order made

payable to Amprobe.

In-warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During the

warranty period, any defective test tool can be returned to your Amprobe distributor for an

exchange for the same or like product. Please check the “Where to Buy” section on amprobe.com for

a list of distributors near you. Additionally, in the United States and Canada, in-warranty repair and

replacement units can also be sent to an Amprobe Service Center (see address below).

Non-warranty Repairs and Replacement – United States and Canada

Non-warranty repairs in the United States and Canada should be sent to an Amprobe Service

Center. Call Amprobe or inquire at your point of purchase for current repair and replacement rates.

USA: Canada:

Amprobe Amprobe

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe distributor for a nominal charge.

Please check the “Where to Buy” section on beha-amprobe.com for a list of distributors near you.

Beha-Amprobe*

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

beha-amprobe.com

*(Correspondence only – no repair or replacement available from this address. European

customers please contact your distributor.)

1

AT-6010 Advanced Wire Tracer

CONTENTS

1. PRECAUTIONS AND SAFETY MEASURES ..................................................................2

2. KIT COMPONENTS ......................................................................................................5

2.1 AT-6010-R Receiver .............................................................................................................5

2.2 AT-6010-T Transmitter ........................................................................................................6

2.3 CT-400 Signal Clamp (optional accessory for the AT-6010) .............................................9

3. MAIN APPLICATIONS ................................................................................................. 10

3.1 Tracing – Energized and De-energized Wires ................................................................... 11

3.2 Identifying Breakers and Fuses (Energized and De-energized) ....................................... 13

4. SPECIAL APPLICATIONS ............................................................................................. 15

4.1 GFCI-Protected Circuit Wire Tracing ..................................................................................15

4.2 Finding Breaks/Opens ......................................................................................................... 15

4.3 Finding Shorts ....................................................................................................................16

4.4 Tracing Wires in Metal Conduit .........................................................................................16

4.5 Tracing Non-Metallic Pipes and Conduits .........................................................................17

4.6 Tracing Shielded Wires .......................................................................................................17

4.7 Tracing Underground Wires ...............................................................................................18

4.8 Tracing Low Voltage Wires and Data Cables ....................................................................18

4.9 Sorting Bundled Wires .......................................................................................................19

4.10 Mapping a Circuit using Test Leads Connection .............................................................. 19

4.11 Tracing Breakers on Systems with Light Dimmers ...........................................................20

4.12 Signal Clamp (optional accessory) - Closed Loop Circuits ...............................................20

4.13 Signal Clamp (optional accessory) - Mapping Circuits .....................................................21

5. MAINTENANCE ...........................................................................................................22

5.1 Battery Replacement ..........................................................................................................22

5.2 Fuse Replacement ............................................................................................................... 24

6. SPECIFICATIONS .......................................................................................................... 25

2

1. PRECAUTIONS AND SAFETY MEASURES

General

For your own safety and to avoid damage to the instrument it is suggested to follow the

procedures listed below:

NOTE: Before and during measurements be diligent to follow the instructions.

• Make sure that the electrical instrument is operating properly before use.

• Before attaching any of the conductors, make sure the voltage present in the conductor is

within the range of the instrument.

• Keep the instruments in their carrying case when not in use.

• If the Transmitter or Receiver will not be used for a long time, remove the batteries to

prevent leakage in the instruments.

• Use Amprobe approved cables and accessories only.

Safety precautions

• In many instances, dangerous levels of voltage and/or current may be present. Therefore, it

is important to avoid direct contact with any uninsulated current carrying surfaces. Insulated

gloves and protective clothing should be worn in hazardous voltage areas.

• Do not measure voltage or current in wet, damp or dusty places.

• Do not measure voltage in the presence of gas, explosive materials or combustibles.

• Do not touch the circuit under test if no measurement is being taken.

• Do not touch exposed metal parts, such as unused terminals and circuits.

• Do not use the instrument if it appears to be malfunctioning (i.e. if you notice

deformations, breaks, leakage of substances, absence of messages on the display, etc).

SYMBOLS

�

Caution! Refer to the explanation in this manual.

X

WARNING HAZARDOUS VOLTAGE. Risk of electric shock.

Consult user documentation.

T

The equipment is protected by double insulation or reinforced insulation.

Earth (Ground).

Fuse.

Battery.

®

Certiﬁed by CSA Group to North American safety standards.

Conforms to relevant South Korean EMC Standards.

Electromagnetic Compatibility:

Korea (KCC): Class A Equipment (Industrial Broadcasting & Communication Equipment)

[1]

This product meets requirements for industrial (Class A) electromagnetic wave

equipment and the seller or user should take notice of it. This equipment is intended for

use in business environments and is not to be used in homes.

Conforms to relevant Australian standards.

Complies with European Directives.

This product complies with the WEEE Directive marking requirements. The afﬁxed

label indicates that you must not discard this electrical/electronic product in domestic

household waste. Product Category: With reference to the equipment types in the

WEEE Directive Annex I, this product is classed as category 9 “Monitoring and Control

Instrumentation” product. Do not dispose of this product as unsorted municipal waste.

3

Safety information

The product complies with:

• UL/IEC/EN 61010-1, CAN/CSA C22.2 No. 61010-1, Pollution Degree 2,

Measurement CAT III 600 V MAX

• IEC/EN 61010-2-033

• IEC/EN 61010-2-032

• IEC/EN 61010-031 (test leads)

• EMC IEC/EN 61326-1

Measurement Category III (CAT III) is applicable to test and measure circuits connected to the

distribution part of the building’s low-voltage MAINS installation. This part of the installation

is expected to have a minimum of two levels of over-current protective devices between the

transformer and possible connecting points.

CENELEC Directives

The instrument conforms to CENELEC Low-voltage directive 2014/35/EU and Electromagnetic

compatibility directive 2014/30/EU.

X�Warnings: Read Before Using

To avoid the possibility of electric shock or personal injury:

• Use the Product only as speciﬁed in this manual or the protection provided by the

instrument may be compromised.

• Avoid working alone so assistance can be rendered.

• Test on a known signal source within the rated voltage range of the Product both before

and after use to ensure the Product is in good working conditions.

• Do not use the Product around explosive gas, vapor, or in damp or wet environments.

• Inspect the Product before use and do not use if it appears damaged. Check for cracks or

missing plastic. Pay particular attention to the insulation around the connectors.

• Inspect the test leads before use. Do not use if insulation is damaged or metal is exposed.

• Do not use the Product if it operates incorrectly. Protection may be impaired. When in

doubt, have the Product serviced.

• Check the test leads for continuity. Replace damaged test leads before using the Product.

• Have the Product serviced only by qualiﬁed service personnel.

• Use extreme caution when working around bare conductors or bus bars. Contact with the

conductor could result in electric shock.

• Do not hold the Product beyond the tactile barrier.

• Do not apply more than the rated voltage and CAT rating, as marked on the Product,

between the terminals or between any terminal and earth ground.

• Remove test leads from the Product before opening the Product case or battery cover.

• Never operate the Product with the battery cover removed or the case open.

• Use caution when working with voltages above 30 V AC RMS, 42 V AC peak, or 60 V DC.

These voltages pose a shock hazard.

• Do not attempt to connect to any circuit carrying voltage that may exceed the maximum

range of the Product.

• Use the proper terminals, functions and ranges for your measurements.

• When using alligator clips, keep ﬁngers behind the ﬁnger guards.

• Use only exact fuse replacement and speciﬁed replacement parts.

• When making electrical connections, connect the common test lead before connecting the

live test lead; when disconnecting, disconnect the live test lead before disconnecting the

common test lead.

1. PRECAUTIONS AND SAFETY MEASURES

4

• To avoid false readings that can lead to electrical shock and/or injury, replace the batteries

as soon as the low battery indicator appears. Check Meter operation on a known source

before and after use.

• Use only AA batteries, properly installed in the Meter case, to power the Product

(see Section 5.1: Battery Replacement).

• When servicing, use only speciﬁed user serviceable replacement parts.

• Adhere to local and national safety codes. Individual protective equipment must be used to

prevent shock and arc blast injury where hazardous live conductors are exposed.

• Only use the test lead provided with the Product or UL Listed Probe Assembly rated CAT III

600 V or better.

• Do not use the HOT STICK (TIC 410A) to operate the AT-6000-R Receiver at voltages above 600 V.

• Remove the batteries if the Meter is not used for an extended period of time, or if stored

in temperatures above 122 °F (50 °C). If the batteries are not removed, battery leakage can

damage the Meter.

• Follow all battery care and charging instructions from the battery manufacturer.

• Do not use the Product to check for absence of voltage. Please use a voltage tester instead.

This manual contains information and warnings that must be followed for safe operation

and maintenance of the instrument. If the Product is used in a manner not speciﬁed by the

manufacturer, the protection provided by the Product may be impaired. This Product meets

water and dust protection IP52 (Receiver) and IP40 (Transmitter and signal clamp) per IEC

60529. Do NOT operate outside during periods of rainfall. The Product is double insulated for

protection per EN 61010-1 to CAT III 600 V.

CAUTION: Do not connect the Transmitter to a separate ground in Electrically Susceptible Patient

areas of a health care facility. Make the ground connection before disconnecting.

Your shipping box should include:

AT-6010 KIT

AT-6010-R RECEIVER 1

AT-6010-T TRANSMITTER 1

TL-6000-INTL TEST LEAD AND ACCESSORY KIT* 1

CC-6010 SOFT CARRYING CASE 1

USER MANUAL 1

1.5 V AA (IEC LR6) BATTERY 12

*TL-6000-INTL test lead and accessory kit includes:

• 2 x 1 m test leads (red, black)

• 1 x 7 m test lead (green)

• 2 x Alligator clips (red, black)

• 2 x Outlet blade adapter (red, black)

• 2 x Outlet round adapter (red, black)

Optional accessories:

ADPTR-SCT Socket adapter

HS-1 Magnetic hanger

TL-7000-25M Test lead

CT-400 Signal clamp

1. PRECAUTIONS AND SAFETY MEASURES

5

2.1 AT-6010-R Receiver

The AT-6010-R Receiver detects the signal in wires and cables. The signal is generated by the AT-

6010-T Transmitter, which is connected to the wire.

The main advantage of this method is the ability to trace the path of the particular wire using

the Receiver. Since the signal is not present in any neighboring wires, the Receiver will

detect only the wire that is connected to the Transmitter.

Note: The Receiver will NOT detect signals from a wire through metal conduit or shielded cable. Refer

to Special Applications, section 4.4 “Tracing Wires In Metal Conduit” for alternative tracing methods.

TIP SENSOR

RUBBER OVER

MOLDED

ENCLOSURE

SENSITIVITY

ADJUSTMENT

BUTTON (+/-)

VOLUME

ADJUSTMENT

BUTTON (+/-)

POWER BUTTON

BATTERY

COMPARTMENT

(Back side)

TACTILE

BARRIER

SOUND

VOLUME

SIGNAL

STRENGTH (0-99)

BATTERY STATUS

SENSITIVITY

LEVEL (1-8)

BARGRAPH -

proportional to

signal strength

ENERGIZED/

DE-ENERGIZED

Figure 2.1: Overview of AT-6010-R Receiver

POWER BUTTON: Short press to turn the Receiver on. Long press >2s to turn the Receiver off.

VOLUME ADJUSTMENT: The volume can be changed by short presses on the volume +/- buttons.

The mute and four loudness level are available. The chosen volume level will be shown on the display.

TIP SENSOR: The LED on the Tip Sensor will blink when a signal is detected. The stronger the

signal, the faster the blinking.

SENSITIVITY: Press +/- buttons to adjust the sensitivity of the Receiver. Eight levels are available.

2. KIT COMPONENTS

6

2.2 AT-6010-T Transmitter

The AT-6010-T Transmitter works on Energized and De-energized circuits up to 600 V AC/DC in

Category I through Category III electrical environments.

Transmitter signal modes:

High Signal (Hi) – The HIGH mode function is recommended for most wire tracing applications

on Energized and De-energized circuits including breaker location. This function will be used

majority of the time.

Loop mode – This mode is initiated by short pressing On/Off button. Loop LED is On when this

mode is activated. It should be used when working with closed loop De-energized circuits, such

as shorted wires, shielded cables or De-energized wires that are grounded on the far-end.

How is the Loop function different from the Hi setting when using test leads?

HIGH mode (Hi) generates a signal in all open branches of the De-energized circuit. This is useful

when tracing open wires. Hi mode will NOT work on wires that are grounded on the far-end

because the signal cannot be generated.

Figure 2.2a: Generating a signal with HIGH mode

Loop mode generates a signal (current ﬂow) in closed loop De-energized circuits only. Loop

mode is used to pinpoint the location of a short (because the current will not be able to ﬂow in

open branches) and to trace wires that are grounded on the far end (because the loop is closed

via ground connection).

2. KIT COMPONENTS

7

Figure 2.2b: Generating a signal in Loop mode

Note: Loop mode only works on De-energized circuits. It is automatically disabled when the

Transmitter is connected to an Energized line with test leads.

Working with the Transmitter:

When the Transmitter is on and connected to the circuit with test leads, it checks for voltage.

A red Voltage Warning Indicator will light up if the Transmitter detects dangerous voltage levels

above 30 V AC/DC.

IMPORTANT!

The Voltage Warning Indicator light will blink when overvoltage (> 650 V AC/DC) is detected. In

case of overvoltage immediately disconnect the Transmitter from the circuit.

This Voltage Waning Indicator is not designed to check for absence of voltage. Please use a

voltage tester instead.

The Transmitter starts generating a tracing signal as soon as it is turned on. Based on the detected

voltage, the Transmitter automatically switches to either:

• Energized mode (30 to 600 V AC/DC) generating 6 kHz frequency

• De-energized mode (0 to 30 V AC/DC) generating 33 kHz frequency

Energized mode uses a lower transmission frequency (6 kHz) than De-energized mode (33 kHz)

to reduce signal coupling between wires. De-energized mode requires a higher frequency in

order to generate a reliable signal.

2. KIT COMPONENTS

8

Energized mode: In Energized mode, the Transmitter draws a very low current from the Energized

circuit and generates a 6 kHz signal. This is a very important feature of the Transmitter, since drawing

current does not inject any signal that would harm sensitive equipment connected to the circuit. The

signal is also generated in a direct path between the Transmitter and the power source, thus NOT

placing a signal onto any branches enabling wiring tracing directly back to the breaker panel. Please

note that due to this feature, the Transmitter has to be connected on the load side of the circuit.

De-energized mode: In De-energized mode, the Transmitter injects a 33 kHz signal onto the

circuit. In this mode, the signal will travel though all the circuit branches because it is injected.

The high frequency/low energy signal will not harm any sensitive equipment.

Figure 2.2c: Overview of AT-6010-T Transmitter

VOLTAGE WARNING

INDICATOR

1. Red: Energized

2. Off: De-energized

3. Blinking: Overvoltage

ON / OFF BUTTON

HIGH SIGNAL MODE

LOW BATTERY

INDICATION

RUBBER OVERMOLDED

ENCLOSURE

LOOP SIGNAL MODE

ON/OFF:

• Long press >2s to turn the Transmitter on (Transmitter is automatically in HIGH mode).

• Short press ON/OFF button to switch between HIGH and LOOP mode.

• Long press >2s to turn the Transmitter off.

VOLTAGE WARNING INDICATOR: The warning light will be ON for Energized circuits

(30 to 600 V AC/DC), OFF for De-energized circuits (0 to 30 V AC/DC), and BLINKING if an overvoltage

is detected (> 650 V AC/DC).

Low battery indication:

LED OFF Batteries OK approx. 10V to 12V

LED ON Low battery warning approx. 9.5V to 10V

LED Blinking Replace battery approx. 7.3V to 9.5V

Device will power off if voltage is below 6.9 V

2. KIT COMPONENTS

9

2.3 CT-400 Signal Clamp

(optional accessory for the AT-6010)

The Signal Clamp accessory is used for applications when where is no access to the bare

conductors. The clamp attachment enables the Transmitter to induce a signal through the

insulation into either wires. The clamp works on low impedance closed circuits.

CONNECTORS TO

TRANSMITTER

JAW

TACTILE

BARRIER

JAW

RELEASE

TEST LEAD

Figure 2.3: Overview of CT-400 Signal Clamp

2. KIT COMPONENTS

10

X� IMPORTANT NOTICE, PLEASE READ BEFORE STARTING TRACING

Avoiding signal cancellation problems with a separate ground connection

The signal generated by the Transmitter creates an electromagnetic ﬁeld around the wire. This

ﬁeld is what is detectable by the Receiver. The clearer this signal, the easier it is to trace the wire.

If Transmitter is connected to two adjacent wires on the same circuit (for example, hot and neutral

wires on a Romax cable), the signal travels in one direction through the ﬁrst wire and then returns

(in opposite direction) through the second. This causes the creation of two electromagnetic ﬁelds

around each wire with opposite direction. These opposing ﬁelds will partially or completely cancel

each other out, making wire tracing difﬁcult if not impossible.

To avoid the cancellation effect, a separate ground connection method should be used. The red

test lead of the Transmitter should be connected to the hot wire of the circuit you wish to trace,

and the green lead to a separate ground, such as water pipe, ground stake, metal grounded

structure of the building, or outlet ground connection of an outlet on a different circuit. It is

important to understand that an acceptable separate ground is NOT the grounding terminal

of any receptacle on the same circuit as the wire you wish to trace. If hot wire is Energized and

the Transmitter is properly connected to a separate ground, the red LED on the Transmitter

will light up. The separate ground connection creates maximum signal strength because the

electromagnetic ﬁeld created around the hot wire is not being cancelled by a signal on the

return path ﬂowing along an adjacent wire (hot or neutral) in the opposite direction, but

rather through the separate ground circuit.

3. MAIN APPLICATIONS

11

3.1 Tracing – Energized and De-energized Wires

Connecting test leads to the Transmitter

1. Connect the green and red test leads to the

Transmitter (polarity does not matter).

2. Using provided test leads accessories, connect the

red test lead to the wire being traced, Energized or

De-energized. For receptacles, make sure to connect

the test lead to the line (hot) wire. For Energized

systems the signal will ONLY be transmitted between

the load-side to which the Transmitter is connected

and the source of power (see Figure 3.1a).

3. Connect the green wire to a separate ground

(metal building structure, metal water pipe, or

ground wire on a separate circuit).

*Note: Please note that if working with GFCI protected

circuits, this method will trip the GFCI protection. Refer

to Special Applications, section 4.1 “GFCI-Protected

Circuit Wire Tracing” for alternative tracing methods.

TIP: The Transmitter, with the red test lead, can be directly connected to the live wire of the

working electrical equipment under load (motor, electronics, etc). Tracing can be performed

without needing to turn off the equipment or switching power off.

Figure 3.1b: Connecting Transmitter to Energized working system

Setting up the AT-6010-T Transmitter

1. Press ON/OFF key to turn on the Transmitter.

2. Verify that the test leads are properly connected;

the red LED voltage status light should be on for

circuits with voltage above 30 V AC/DC, and it should

be off for De-energized circuits below 30 V AC/DC.

Note: Make sure to use the separate ground

connection as described above.

3. HIGH signal mode is automatically activated when the

Transmitter is turned on. The LED on the Transmitter

should appear as in Figure 3.1c.

Figure 3.1c: Transmitter indicator

showing signal in HIGH mode

3. MAIN APPLICATIONS - TRACING ENERGIZED AND DE-ENERGIZED WIRES

Figure 3.1a: Proper connection with

separate ground

12

Using the AT-6010-R Receiver in Tracing Mode

Use Receiver to precisely pinpoint the wire location or the place of the fault. The Receiver will

indicate detected signal strength using a two digit readout, bar graph and sound.

1. Turn the Receiver on. Tracing mode is automatically activated.

2. Scan target area with the Tip Sensor to ﬁnd the highest signal level. While tracing,

periodically adjust sensitivity to keep the signal strength near 50. Increase or decrease

sensitivity by pressing + or - on the keypad.

3. For best results while tracing Energized wires, align groove on the Tip Sensor with wire

direction as shown in Figure 3.1d. Signal may be not detected if not properly aligned. To

verify wire direction, periodically rotate the Receiver 90 degrees. Signal strength will be the

highest when wire is aligned with the Tip Sensor groove.

Depending on the detected signal, the Receiver automatically switches to either Energized

or

De-energized mode, and displays this information on the LCD. No manual setup is necessary.

Tip

groove

Figure 3.1d: Aligning the Tip Sensor groove

Note: For best results, keep the Receiver at least 3 feet from the Transmitter and test leads to

minimize signal interference.

3. MAIN APPLICATIONS - TRACING ENERGIZED AND DE-ENERGIZED WIRES

13

3.2 Identifying Breakers and Fuses (Energized and De-energized)

Note: For breaker locating, a simpliﬁed direct connection to hot and neutral wires can be used

because these wires are separated at the breaker panel. There is no risk of signal cancellation

effect if wires are at least a few inches away from each other. However, the separate ground

connection (section 3.1) should be used for superior results speciﬁcally if wires need to be

traced in addition to breaker identiﬁcation.

The simpliﬁed direct connection to hot and neutral wire will NOT trip the GFCI circuit.

Figure 3.2b: Separate ground connection

(Preferred)

Figure 3.2a: Simpliﬁed direct connection

Connecting the test leads

1. Connect the Transmitter using either simpliﬁed direct connection or separate ground connection.

2. If the simpliﬁed direct connection method is used, connect the test leads directly to the hot and

neutral wires. While locating a breaker, wires will not be traceable as the signals will cancel each

other out.

3. For separate ground connection, connect the red lead to the line (hot) wire on the load side of the

system. The wire can be energized or de-energized. Connect the green lead to a separate ground,

such as a metal building structure, metal water pipe, or ground wire on a separate circuit.

TIP: The Transmitter, with the red test lead, can be directly connected to the live wire of the

working electrical equipment under load (motor, electronics, etc). Tracing can be performed

without needing to turn off the equipment or switching power off.

3. MAIN APPLICATIONS - TRACING ENERGIZED AND DE-ENERGIZED WIRES

14

Figure 3.2c: Connecting Transmitter to Energized working system

Setting up the AT-6010-T Transmitter

1. Press the ON/OFF key to turn on the Transmitter.

2. Verify that the test leads are properly connected. The red LED voltage status light will

illuminate for Energized circuits with a voltage above 30 V AC/DC. If the voltage is

De-energized, the light will be off.

3. HIGH signal mode is automatically activated when Transmitter is turned on.

Using the AT-6010-R Receiver

1. Turn the Receiver on. Tracing mode is automatically activated.

2. Align the groove on the Tip Sensor with the breaker lengthwise (See Figure 3.2d).

3. Scan all breakers in any order to ﬁnd a breaker with the highest signal. Adjust sensitivity by

pressing + or - on the keypad to show the signal strength near 50 for the breaker with the

highest signal. After any sensitivity adjustment rescan all breakers to ﬁnd the one with the

highest signal level.

Important note: Differentiation in breaker designs, height and internal contact structure may

affect the precision of breaker identiﬁcation. For most reliable results, remove the breaker panel

cover and perform a scan on the wires instead of the breakers.

Depending on the detected signal, the Receiver automatically switches to either Energized

or

De-energized mode, and displays this information on the LCD

.

Figure 3.2d: Aligning the Tip Sensor groove with the breaker

3. MAIN APPLICATIONS – LOCATING BREAKERS

15

4.1 GFCI-Protected Circuit Wire Tracing: Connecting the AT-6010-T Transmitter to GFCI

Protected Circuits

Connecting the Transmitter to an Energized GFCI protected circuit using a separate ground

method will trip the GFCI protection. Use the following methods to work with GFCI protected

circuits. For a De-energized GFCI-protected outlet that is not tripped, you can connect test leads

directly to the outlet contacts using the De-energized Tip Sensor mode.

Method 1 – Bypass the GFCI circuitry to avoid tripping GFCI:

(for Energized GFCI-protected outlets only)

• Remove the protective receptacle wall plate.

• Using the alligator clip, attach the red test lead to the screw to connect the Energized hot

wire to the receptacle.

• Connect the green test lead using a separate ground method.

• Perform tracing as described in sections 3.1 or 3.2.

Method 2 – Do NOT use separate ground to avoid tripping GFCI:

(for GFCI-protected outlets and breakers)

• Connect the Transmitter with the test leads to the Neutral and Hot wires.

• Perform tracing as described in sections 3.1 or 3.2.

Note: This type of connection causes signal coupling and reduces signal strength. If the signal is

too weak or untraceable, use Method 3.

Method 3 - De-energize the circuit:

(for GFCI-protected breakers)

• Connect the Transmitter directly to the wire as described in section 3.1.

• Perform tracing as described in sections 3.1 or 3.2.

4.2 Finding Breaks/Opens

It is possible to pinpoint the exact location where a wire is broken, even if the wire is located

behind walls, ﬂoors or ceilings.

1. Make sure that wire is De-energized.

2. Use the steps described in section 3.1 to connect the Transmitter and perform tracing.

3. For best results, ground all De-energized wires that run in parallel with the black test lead.

Figure 4.2: Locating a break or open

4. SPECIAL APPLICATIONS

16

4. SPECIAL APPLICATIONS

The tracing signal generated by the Transmitter is conducted along the wire as long as there is

continuity in the metal conductor. To ﬁnd a fault, trace the wire until the signal stops. To verify the

fault’s location, move the Transmitter to the other end of the wire and repeat, tracing from the

opposite end. If signal stops at the exact same location, the fault has been located.

Note: If the place of the fault is not found, the result may be a high resistance break (partially

open circuit). Such a break would stop higher currents from ﬂowing but will conduct the tracing

signal through the break. Such faults will not be detected until the wire is completely open.

4.3 Finding Shorts

Shorted wires will cause a breaker to trip. To correct this, disconnect the wires and make sure the

ends of the wires on both sides of the cable are isolated from each other and other wires or loads.

1. Connect the Transmitter with the test leads to the circuit as shown in Figure 4.3.

2. Switch the Transmitter to Loop mode by short press of On/Off button. Verify that the Loop LED is ON.

3. Turn on the Receiver. Tracing mode is automatically activated.

Start tracing the cable until the signal stops. To verify the place of the fault, move the Transmitter

to the other end of the wire and repeat tracing from the opposite end. If the signal stops at the

exact same location the fault has been located.

Figure 4.3: Tracing a cable to ﬁnd shorts

Note: This method will be affected by signal cancellation effect. Expect a relatively weak signal.

4.4 Tracing Wires in Metal Conduit

The Receiver is unable to pick up the signal from a wire through a metal conduit. The metal

conduit will completely shield the tracing signal.

Note: The Receiver will be able to detect wires in a non-metallic conduit. For these applications

follow general tracing guidelines.

To trace wires in a metal conduit:

1. Turn on the Receiver. Tracing mode is automatically activated.

2. Open junction boxes and use the Receiver Tip Sensor to detect which wire in the junction

box is carrying the signal.

3. Move from junction box to junction box to follow the path of the wire.

Note: Applying a signal directly to the conduit will send the signal through all the conduit

branches, making tracing a particular conduit path impossible.

La page charge ...

Ampro AT-6010-R Manuel utilisateur

Ampro AT-6010-R Manuel utilisateur

dans d''autres langues

Autres documents