Avanti RIM49U3S-IS Manuel utilisateur

1

Model / Modelo / Modelé: RIM49U3S-IS

ICE MAKER

MAQUINA DE HACER HIELO

MACHINE A GLAÇONS

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS.

Avanti has a policy of continuous improvement on its products and reserves

the right to change materials and specifications without notice.

Avanti Products LLC

P.O. Box 520604

Miami, FL 33152

www.avantiproducts.com

2

TABLE OF CONTENTS

Appliance Safety

3

Important Safeguides

4

Electrical Connection

5

Help Us Help You

6

Parts and Features

7

Important Safety Instructions

8

Installation Instructions

8

Before Using Your Appliance

8

Installation of Your Appliance

9 -13

Operating Your Appliance

14 – 16

How Your Appliance Makes Ice

17

Care and Maintenance

18 – 21

Troubleshooting Guide

22 – 23

Service for Your Appliance

24

Wiring Diagram

24

Your Avanti Products Warranty

25

Instrucciones en Español

26 – 45

Instructions en Français

46 - 69

Registration Information and Registration Card

Last page

3

APPLIANCE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your

appliance. Always read and obey all safety messages.

This is the Safety Alert Symbol. This

symbol alerts you to potential

hazards that can kill or injure you

and others.

All safety messages will follow the

Safety Alert Symbol and either the

wards” DANGER”, “WARNING” or

“CAUTION”.

Danger means that failure to heed

this safety statement may result in

severe personal injury or death.

Warning means that failure to heed

this safety statement may result in

extensive product damage, serious

personal injury, or death.

Caution means that failure to heed

this safety statement may result in

minor or moderate personal injury,

or property or equipment damage.

All safety messages will alert you to what the potential hazard is, tell you how to

reduce the chance of injury, and let you know what can happen if the instructions

are not followed.

PROP. 65 WARNING FOR CALIFORNIA RESIDENTS

WARNING:

Cancer And Reproductive Harm

www.p65warnings.ca.gov

4

IMPORTANT SAFEGUARDS

Before the beverage cooler is used, it must be properly positioned and installed

as described in this manual, so read the manual carefully. To reduce the risk of

fire, electrical shock or injury when using the beverage cooler, follow basic

precautions, including the following:

Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do

not use an extension cord

• Replace all panels before operating

• It is recommended that a separate circuit, serving only your beverage cooler, be provided. Use

receptacles that cannot be turned off by a switch or pull chain

• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or

explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance. The fumes can create a fire hazard or explosion.

• Before proceeding with cleaning and maintenance operations, make sure the power line of the unit

is disconnected.

• Do not connect or disconnect the electric plug when your hands are wet

• Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do so can

result in electrical shock or death.

• Do not attempt to repair or replace any part of your appliance unless it is specifically recommended

in this material. All other servicing should be referred to a qualified technician.

• Use two or more people to move and install the appliance. Failure to do so can result in back or

other injury.

• To ensure proper ventilation for your appliance, the unit must be completely unobstructed. Choose a

well-ventilated area with temperatures above 55

0

F (13

0

C) and below 90

0

F (32

0

C). This unit must

be installed in an area protected from the elements, such as wind, rain, water spray or sunlight.

• The appliance should not be located next to ovens, grills or other sources of high heat.

• The appliance must be installed with all electrical, water and drain connections in accordance with

state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in

accordance with the National Electrical Code and local codes and ordinances is required.

• Do not kink or pinch the power supply cord of the appliance.

• The fuse (or circuit breaker) size should be 15 amperes.

• It is important for the appliance to be leveled in order to work properly. You may need to make

several adjustments to level it.

• All installation must be in accordance with local plumbing code requirements.

• Make certain that the pipes are not pinched or kinked or damaged during installation.

• Check for leaks after connection.

• Never allow children to operate, play with or crawl inside the appliance

• Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage

or discolor the interior.

• Do not use this apparatus for other than its intended purpose.

5

Electrical Connection

~Warning~

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord

is damaged, have it replaced by an authorized Avanti Products service center.

This appliance should be properly grounded for your safety. The power cord of this

appliance is equipped with a three-

prong plug which mates with standard three

prong wall outlets to minimize the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the

power cord supplied.

This appliance requires a standard 115Volts~/60Hz electrical outlet with three-prong

ground.

The cord should be secured behind the appliance and not left exposed or dangling to

prevent accidental injury.

Never unplug the appliance by pulling the power cord. Always gri

p the plug firmly

and pull straight out from the receptacle.

Do not use an extension cord with this appliance. If the power cord is too short, have

a qualified electrician or service technician install an outlet near the appliance.

Ø EXTENSION CORD

Because of potential safety hazards under certain conditions, it is strongly

recommended that you do not use an extension cord with this unit. However, if you

must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed, 3-

wire grounding type appliance extension cord having a grounding type plug and

outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

Ø SURGE PROTECTOR

Most electrical appliances use a series of electric control boards to operate. These

boards are very susceptible to power surges and could be damaged or destroyed.

If the appliance is going to be used in an area or if your city / country is prone to

power surges / outages; it is suggested that you use a power surge protector for all

electrical devices / appliances you use. The surge protector that you select must

have a surge block high enough to protect the appliance it is connected to. If you

have any questions regarding the type and size of surge protector needed contact a

licensed electrician in your area.

Damages due to power surges are not considered a manufacturer covered defect

and will void your product warranty.

6

HELP US HELP YOU...

Read this guide carefully.

It is intended to help you operate and

maintain your new appliance properly.

Keep it handy to answer your questions.

If you don't understand something or you

need more help, please call:

Avanti Customer Service

800-220-5570

Keep proof of original purchase date (such as

your sales slip) with this guide to establish

the warranty period.

Write down the model and serial numbers.

You'll find them on a plate located on the rear

outside wall of the appliance.

Please write these numbers here:

__________________________________

Date of Purchase

__________________________________

Model Number

__________________________________

Serial Number

Use these numbers in any correspondence or

service calls concerning your appliance.

If you received a damaged appliance, immediately

contact the dealer (or builder) that sold you the

appliance.

Save time and money. Before you call for service,

check the Troubleshooting Guide. It lists causes of

minor operating problems that you can correct

yourself.

IF YOU NEED SERVICE

We're proud of our service and want you to

be pleased. If for some reason you are not

happy with the service you receive, here are

some steps to follow for further assistance.

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the details,

including your telephone number, and send it to:

Customer Service

Avanti Products

10880 NW 30 Street

Miami, FL 33172 USA

CAUTION:

THIS APPLIANCE IS NOT

DESIGNED FOR THE STORAGE

OF MEDICINE OR OTHER

MEDICAL PRODUCTS.

7

PARTS AND FEATURES

8

IMPORTANT SAFETY INSTRUCTIONS

− Read all instructions before using the icemaker.

− DANGER or WARNING: Risk of child entrapment. Child entrapment and suffocation are not problems

of the past. Junked or abandoned icemakers are still dangerous . . . even if they will “just sit in the

garage a few days”.

− Before you throw away your old icemaker: take off the doors. Leave the shelves in place so that

children may not easily climb inside.

− Never allow children to operate, play with, or crawl inside the icemaker.

− Never clean

icemaker parts with flammable fluids. The fumes can create a fire hazard or explosion.

− Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other

icemaker. The fumes can create a fire hazard or explosion.

INSTALLATION INSTRUCTIONS

Before Using Your Icemaker

• Remove the exterior and interior packing.

• Check to be sure you have all of the following parts:

o 1 Ice Scoop

o 1 Water Supply Hose

o 1 Water Drain Hose

o Instruction Manual

• Before connecting the unit to the power source, let it stand upright for approximately 2 hours.

This will reduce the possibility of a malfunction in the cooling system from handling during

transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

EXCESSIVE WEIGHT HAZARD

USE TWO OR MORE PEOPLE TO MOVE AND INSTALL THE ICEMAKER

FAILURE TO DO SO CAN RESULT IN BACK OR OTHER INJURY

~

WARNING

~

To reduce the risk of fire, electrical shock, or

injury when using your icemaker, follow these

basic precautions:

This Unit Is For Indoor Use Only

- SAVE THESE INSTRUCTIONS -

9

INSTALLATION OF YOUR ICEMAKER

• THIS ICEMAKER SHOULD BE PROPERLY INSTALLED BY A QUALIFIED PROFESSIONAL

This icemaker MUST be installed with electrical and water connections in accordance with

all state and local codes.

• Allow a minimum of 1 inch of space between the top and sides of the icemaker and a

minimum of 4 inches at the back, which allows the proper air circulation to cool the

compressor. Ensure the front of the unit is completely unobstructed.

• Place your icemaker on a floor that is strong enough to support the icemaker when it is fully

loaded. To level your icemaker, adjust the legs at the front of the icemaker.

• Locate the icemaker away from direct sunlight and sources of heat (stove, heater, radiator, etc.).

Direct sunlight may affect the acrylic coating and heat sources may increase electrical

consumption. Extreme cold ambient temperatures may also cause the icemaker not to perform

properly.

• Choose a well ventilated area with temperatures above 50ºF (10ºC) and below 100ºF (38ºC).

This unit MUST be installed in an area protected from the elements.

• Avoid locating the icemaker in moist areas. Too much moisture in the air will cause frost to form

quickly on the evaporator requiring more frequent defrosting of the icemaker.

INSTALLATION CLEARANCES:

• The installation of this icemaker requires a cold water supply inlet of ¼” (6.35mm) soft copper tubing

with a shut off valve.

• The icemaker requires a continuous water supply with a minimum pressure of 15 psig and a static

pressure not to exceed 80 psig. The temperature of the water supply into the icemaker should be

between 41ºF (5ºC) and 90ºF (32ºC) for proper operation.

• It is strongly recommended that a water filter be used. A filter, if it is of the proper type, can remove

taste and odors as well as particles. Some water is very hard, and softened water may result in

white, mushy cubes that stick together. De-Ionized water is NOT recommended.

Warning

Operation of the icemaker for extended periods outside of the normal

temperature ranges as described above may affect product performance.

SIDE VIEW

TOP VIEW

Top of unit

Rear of unit

Front of unit

Side Side

4”

1”

10

Leveling the ice maker

It is important for the icemaker to be leveled in order to

work properly. It can be raised or lowered by rotating

the plastic sheaths around each of the four feet on the

bottom of the machine .If you find that the surface is

not level, rotate the feet until the ice maker becomes

level .You may need to make several adjustments to

level it. We recommend using a carpenter’s level to

check the machine.

1. Place a carpenter’s level on top of the product to see if

the ice maker is level from front to back and side to side.

2. Adjust the height of the feet as follows:

Turn the leveling feet to the right to lower that side of the ice maker.

Turn the leveling feet to the left to raise that side of the ice maker.

IMPORTANT: Once you are ready to install it in a cabinet or directly on the floor, you must adjust the

feet to level the ice maker. If the floor is level, just revolve the two front feet to touch the floor.

Reversing the door swing

Tools needed: Flat head screwdriver, Phillips screwdriver

IMPORTANT: Before you begin, unplug the ice maker or disconnect power.

To remove door from hinges:

1. Remove top hinge cover by pushing it toward the back of the unit, then lifting it off.

2. Using a Phillips screwdriver, remove the screws, then remove the top hinge mat and top hinge.

Keep the parts together and set them aside.

3. Lift the door off of the bottom hinge and set the door aside.

To replace door on hinges:

1. Using a flathead screwdriver, remove

the plug buttons from the screw holes

opposite the door hinges, top and

bottom. Set aside.

2. Remove the front louver. Set aside.

3. Remove the bottom hinge and place it

on the opposite side at the bottom of the

door.

4. Position the door on the bottom hinge.

5. Align the door on the bottom hinge and

replace the top hinge and top hinge mat.

6. Replace top hinge cover by pressing it

down over the hinge mat and then

pushing it forward.

7. Push the plug buttons into the original

screw holes.

down

up

11

Water Supply

The water supply should be ready at the point of installation. The water supply pressure should be a

minimum of 15 psig with a static pressure not more than 80 psig. (A wall outlet directly behind the ice

machine will make installation easier.)

IMPORTANT:

1. All installations must be in accordance with local plumbing code requirements. Professional

installation is recommended.

2. Make certain the hoses are not pinched or kinked or damaged during installation.

3. Check for leaks after connection.

Tools required: ½-in. open-end wrench, Phillips screwdriver

Connecting the water line:

1. Turn off main water supply. Turn on the nearest faucet long enough to clear line of water.

2. Find a ½-in. to ¾-in. vertical cold water pipe near the installation location. The distance should be

less than 6 feet. The water supply hose provided with the ice maker is approximately 6 feet long.

3. A shut-off valve must be installed to the main water supply. If the water pipe has a plain piece of

copper tubing, attach a ¼” O.D. compression union to the tubing and install the valve.

4. Connect the nut of the water supply hose to the tap, and connect the other end with the water

inlet. Tighten firmly by hand, then one-half turn with wrench.

5. Turn on main water supply and tap. Check for water supply connection leaks. Tighten every

connection (including connection at the water inlet).

IMPORTANT: When you connect the water supply hose and the drain hose, pay

attention to the indications of “Water inlet” and “Drain outlet” on the machine.

Drain

You must connect the drain line before using the ice maker. Follow the steps outlined below.

There are two types of ice machine modes, one that drains by gravity and one

that has an internal drain pump.

This unit can pump out water up to a rise of 1.5m (59”) or over a horizontal

length of 1.5m (59”).

Vertical Drain

Horizontal Drain

12

Connecting the drain line:

NOTE: If there is a drain line near the ice maker, the best choice is to drain

water to the drain line through the drain water hose provided with ice

maker.

1. Locate the floor drain near the ice maker. The distance should be less than 5 feet

since the length of the long drain water hose provided with the ice maker is about

5 feet.

2. Find the drain outlet on the back of ice maker. Connect the drain outlet to the

water draining hose, and insert the other end of the hose into the drain line.

NOTE: Never allow the drain hose to hang or loop higher than the floor of the ice

storage bin.

3. All horizontal runs of drain lines must have a fall of ¼” per foot. An air gap will

likely be required between the ice maker drain tube and the drain/waste

receptacle. A standpipe with a trap below it would be acceptable for the

drain/waste receptacle. A floor drain is also acceptable. If this is not possible, the

use of a condensate pump is recommended.

4. Pour 1 gallon of water into the ice storage bin to check for leaks in the drainage system.

Tighten any connections that leak.

IMPORTANT: This ice maker is not a freezer. Infrequent drainage

will cause a high rate of melting in the ice storage bin.

How the drain system operates when water is pumped out

The components of the Pump-Out Water Drain System are

• Water reservoir PC Board & Water level switch 1, 2

• Water Drain Pump

OPERATION

• All water coming from the overflow and the melted ice is collected in the water reservoir.

• As soon as the water in the reservoir reaches the maximum level, the water level switch 1

closes, transmitting a low voltage current to the PC Board.

Water level switch 2

Water level switch 1

13

• The PC board activates the water drain pump for 20 seconds,

pumping out most of the water contained in the water reservoir.

• The water can be pumped out up a rise of to 1.5m (59”) or

over a on horizontal length of 1.5m (59”).

• If water level switch 2 closes, transmitting a low-voltage

current to the PC board, the PC board activates the

buzzer alarm, informing you that the drain pump, water

level switch or drain tube may be malfunctioning.

Schematic Diagram

NOTE:

The outlet of the drain hose

must be raised higher than

the water surface to prevent

the drained water from

flowing back into the water

reservoir.

WARNING!

If alarm buzzer sounds, turn

off the ice maker and the

water supply, remove all ice

from storage bin, and wipe up

any water that may have

overflowed. Check if there is

any water in water trough at

back of unit; if no water,

drainage pump may not be

receiving the proper amount

of power. Check power

source. If the problem can be

corrected, turn on the unit

again. Also check that none

of the water lines are kinked.

If the problem remains,

contact Customer Service.

14

OPERATING YOUR ICEMAKER

Control Panel: Description of buttons and indicator lights:

Indicator Lights:

1. BIN FULL (RED): Bin is full

When this light is illuminated, the ice storage bin is full of ice or there is something blocking the

bin full sensor. The unit will stop the ice making process until the level of ice has reduced or the

object blocking the sensor is removed.

When ice-cubes are removed and the bin full sensor is cleared; the bin-full indicator light will blink

for 3 minutes, then the unit will restart and return to the ice-making process.

2. ICE (Green): Ice making process.

When this light is illuminated, the unit is working in the ice-making process which is controlled by

a temperature sensor on the evaporator. When the indicator light flashes green, the unit is

working to produce ice and is based on a fixed timer.

3. HARVEST (Yellow): Ice Harvest process.

When this light is illuminated, the unit is in the process of harvesting the ice that was produced.

The machine will continue to make and harvest ice until the bin-full sensor notes that the bin is

full or until the unit is turned off or the system mode is changed by touching the “MODE” button.

4. Mode button: This button is used primarily for the quick start of the Ice making process or

for service / repair issues. You can “quick start” the system by pressing the “MODE” button when

first plugged in, power has been lost or if the unit has been turned off for a period of time.

5. Adjust button: This button is used primarily for service and or to select the size of the ice-

cubes. To select the ice cubes, press and hold the button for approximately 3 seconds, the

“HARVEST” (Yellow) indicator light will illuminate and the system will enter the Ice Size Selection

mode. Release the button once the Harvest light (yellow) blinks and simply press the ( + ) or ( - )

to select larger or smaller cubes, the unit is shipped from the factory set to the normal sized cubes.

15

OPERATING YOUR ICE-MAKER

1. Turn on the water tap.

2. Press the ON/OFF button.

3. After 3 minutes, the machine will automatically go to the ice-making stage, and the sound of water

flowing will be heard. (The ICE indicator light (GREEN) will blink during this process.)

4. Press the MODE button to quick start the Ice-Making process and allow the water trough to begin

to fill automatically. (The ICE indicator light (GREEN) will blink during this process.)

5. When the batch of ice has been fully formed, the ice will automatically be harvested and drop to

the ice storage bin. (The HARVEST indicator light (YELLOW) will blink during this process.)

6. When the ice storage bin is full, the sheet of cubes will not fall completely and will hold the bin-full

sensor open. The machine will stop making ice automatically. (The BIN-Full indicator light (RED)

will blink to indicate the bin is full or the sensor is being blocked.)

7. The unit will start making ice again after ice cubes are removed or when the bin-full sensor swings

back to operating position. (The BIN-Full indicator light (RED) will continue to blink for

approximately 3 minutes, then the system will automatically begin the ice-making process again.)

IMPORTANT:

• Although the unit has been tested and cleaned at the factory, due to long-term transit and

storage, the first batch of cubes must be discarded.

• Never turn the water supply tap off when the ice maker is working.

• Never touch the evaporator when unit is running!

• To prevent ice from melting and to ensure proper ice formation, keep the door closed except

when removing ice from the bin.

Bin full stage

Ice making stage

Ice harvest stage

16

Ice Size Adjustment Guide:

1. Press and hold the “Adjust” button for approximately 3 seconds. The unit will enter the Ice Size

Adjustment mode. The “HARVEST” LED (yellow) will be blinking continuously while the ice size is

being selected. Release the button when the LED blinks continuously to adjust the ice size.

2. While in the Ice Size Selection mode, press the “Clean” (-) button or the “Mode” (+) button for the

desired ice size.

Smaller ice setting:

By pressing the “Clean” (-) button, you can select the SMALL size of the ice cubes. The “ICE” LED

(GREEN) will flash as you select the smaller ice size.

Larger ice setting:

By pressing the “Mode” (+) button, you can select the large size of the ice cubes. The “BIN FULL”

LED (RED) will flash as you select the larger ice size.

After 10 seconds without any operation, the unit will return to the previous mode.

NOTE:

• If during the ice size adjustment mode the “BIN FULL”, “ICE” and “HARVEST” LEDS blink all at

once; this indicates that the unit is in the regular (middle) setting of the ice size.

• When the machine is in the cleaning stage or ice full stage, the ice size adjustment mode cannot

be accessed

17

HOW THE ICE MAKER PRODUCES ICE

Set the ON/OFF button to the ON position.

The machine will automatically go in to the ice making stage.

The unit will go through two distinct cycles during the production of your ice.

The first cycle is the “freeze” where the ice is actually produced and the

second is the “harvest” where the ice is dropped into the ice-bin.

The freeze cycle happens when water flows to the evaporator surface. The harvest cycle is when the

ice is released and water enters the machine. A complete cycle takes about 20 minutes, but it

depends on temperature and operating conditions.

Freeze: During the freeze cycle the compressor is pumping refrigerant, the fan motor is blowing air,

and the water pump is circulating water. When the batch of ice has been fully formed, the ice maker

stops the freeze cycle and the harvest cycle will begin.

Harvest: During the harvest cycle the compressor is still operating, but the water pump has stopped.

The hot gas valve opens, diverting hot refrigerant gas into the evaporator. The hot refrigerant gas

warms the evaporator, causing the cubes to slide as a unit off the evaporator and into the storage bin.

The freeze cycle will restart when all the cubes have been harvested.

How the machine uses the water

The ice maker begins with a fixed charge of water which is contained in the water trough. As the

water flows to the freezing evaporator surface, the portion of water that does not contain mineral

impurities freezes and sticks to the ice cube molds. The water containing impurities falls back into the

water trough. During the ice making process, fresh water enters into the water trough continuously as

the water in the trough freezes continuously in the evaporator.

Normal sounds

Your new ice maker may make sounds that are not familiar to you. Most of the new sounds are

normal. Hard surfaces like the floor and walls can make the sounds louder than they actually are. The

following list describes the sounds that might be new to you and what may be causing them.

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of

the ice maker can also make noises due to vibration.

• The high efficiency compressor may make a pulsating or high-pitched sound.

• Running water may make a splashing sound.

• You may hear air being forced over the condenser by the condenser fan.

• During the harvest cycle, you may hear the sound of ice cubes falling into the ice storage bin.

18

CARE AND MAINTENANCE

Cleaning The Icemaker

Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The

maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if

you have pets, or there are other special considerations.

Important Note:

Never keep anything in the ice storage bin that is not ice: objects like wine and beer

bottles are not only unsanitary, but the labels may slip off and plug up the drain.

Cleaning the exterior

The door and cabinet may be cleaned with a mild detergent and warm water solution such as 1 oz. of

dishwashing liquid mixed with 2 gallons of warm water. Do not use solvent-based or abrasive

cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water

spotting.

If the door panel is stainless steel, it may discolor when exposed to chlorine gas and moisture. Clean

stainless steel with a mild detergent and warm water solution and a damp cloth. Never use an

abrasive cleaning agent.

Before proceeding with cleaning and maintenance operations, make sure the

power line of the unit is disconnected and the water line is shut off.

If the ice maker is left unused for a long time, before the next use it

must be thoroughly cleaned. Follow carefully any instructions provided

for cleaning or use of sanitizing solutions. Do not leave any solution

inside the ice maker after cleaning.

If the ice maker is left unused for a long time, before the next use it must

be thoroughly cleaned. Follow carefully any instructions provided for

cleaning or use of sanitizing solutions. Do not leave any solution inside

the ice maker after cleaning.

19

Cleaning the interior

The ice storage bin should be sanitized occasionally. Clean the water trough before the ice maker is

used first time and reused after stopping for an extended period of time. It is usually convenient to

sanitize the trough after the ice making system has been cleaned, and the ice storage bin is empty.

1. Disconnect the power to the unit.

2. Open the door and take out the removable ice storage bin. With a clean cloth, wipe down the

interior of unit and ice bin with a sanitizing solution made of 1 ounce of household bleach or

chlorine and 2 gallons of hot (95ºF – 115ºF) water.

3. Pull off the drain hose of the water trough to drain off all water.

4. Rinse thoroughly with clear water.

5. After draining off all water, put back the drain hose of the water

through to the original location.

6. Put the ice storage bin inside the unit.

7. Reconnect power to the unit.

The ice scoop should be washed regularly. Wash it just like any other food

container.

Condenser cleaning

A dirty or clogged condenser prevents proper airflow, reduces ice making capacity, and causes higher

than recommended operating temperatures that may lead to component failure. Have the condenser

cleaned at least once every six months.

1. Unplug the ice maker or disconnect power.

2. Gently pull off the lower front louver.

3. Remove dirt and lint from the condenser and the

unit compartment with the brush attachment of a

vacuum cleaner

.

4. Reassemble the lower front louver.

5. Plug in the ice maker or reconnect power.

Cleaning the water distribution tube

When you find the ice cubes are incompletely formed or the output is low, the water distribution tube

may be blocked. Turn off the power button, gently take out the water distribution tube, locate the holes

in the distribution tube and use a pointed object such as a toothpick to dredge the holes. Then put the

water distribution tube back to its original position. If the tube is badly blocked, clean it as follows:

1. Shut off the water supply

2. Disconnect the water hose from the distribution tube.

3. Gently take out the distribution tube.

4. With a brush, clean the tube with a dilute solution of warm water and a mild detergent such as

dishwashing liquid. After removing the dirt and lint from the surface, rinse the tube with clean

water.

5. Replace the distribution tube.

6. Reconnect the water supply.

Right location of the

drain hose

Condenser

Surface

20

Ice-making system cleaning (CLEAN BUTTON)

Minerals that are removed from the water during the freezing cycle will eventually form a hard, scaly

deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup.

How often to clean the system depends upon how hard your water is or how effective your filtration

may be. With hard water of 15 to 20 grains/gal. (4 to 5 grains/ liter), you may need to clean the system

as often as once every 6 months.

1. Make sure that all the ice is off the evaporator. If ice is being formed, wait until the cycle is

completed, then press the machine’s ON/OFF button on the control panel.

2. Remove all ice from the storage bin.

3. Keep the ice maker connected to the water supply. Pour 8 oz. of Nickel-Safe Ice Maker Cleaner

Solution into the water trough. Then press the ON/OFF button and the CLEAN button, initiating

the wash cycle. The machine will run in the Automatic Clean Mode.

4. Allow 30 minutes for proper cleaning. After cleaning, press the ON/OFF button again. Use a drain

hose on the front of the water trough to drain off the waste water to a convenient container.

NOTE: Don’t drain off the waste water to the inside of the cabinet.

5. Repeat steps 3 and 4 (without Ice Maker Cleaning Solution) three times to rinse the ice making

system thoroughly.

6. Prepare a sanitizing solution made of 1 ounce of household bleach and 2 gallons of hot water

(95ºF to 115ºF). Wipe the entire bin inside and outside, covering the entire surface of the walls.

7. Fill a spray bottle with the sanitizing solution and spray all corners and edges, making sure to

cover all surfaces with the solution.

8. Allow the solution to be in contact for at least 3 minutes, and then dry.

9. Repeat step 5 to rinse the ice making system one more time.

10. Press the ON/OFF button again. The machine will return to the regular ice making mode.

11. Discard the first batch of ice.

The ice machine cleaner contains acids.

DO NOT use or mix with any other solvent-based cleaner products.

Use rubber gloves to protect hands. Carefully read the material safety instructions

on the container of the ice machine cleaner.

Discard the first batch of ice produced after cleaning.

La page charge ...

Avanti RIM49U3S-IS Manuel utilisateur

Ce manuel convient également à

Avanti RIM49U3S-IS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents