Sony VPL-CS5 Manuel utilisateur

Data Projector VPL-CS5/VPL-CX5

4-090-076-13 (1)

Data Projector

GB

FR

ES

Operating Instructions

Mode d’emploi

Manual de instrucciones

VPL-CS5

VPL-CX5

GB

2

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not

open the cabinet. Refer servicing to

qualified personnel only.

For the customers in the USA

If you have any questions about this product,

you may contact:

Sony Electronics Inc.

Attn: Business Information Center (BIC)

12451 Gateway Boulevard

Ft. Myers, Florida 33913

Telephone No.: 800-686-7669

The number below is for FCC related

matters only.

Declaration of Conformity

Trade Name: SONY

Model No.: VPL-CS5/VPL-CX5

Responsible Party: Sony Electronics Inc.

Address: 680 Kinderkamack Road, Oradell,

NJ 07649 U.S.A.

Telephone No.: 201-930-6972

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the

product’s enclosure that may

be of sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the

appliance.

3

GB

For the customers in Canada

This Class B digital apparatus complies with

Canadian ICES-003.

Voor de klanten in Nederland

Gooi de batterij niet weg

maar lever deze in als klein

chemisch afval (KCA).

The socket-outlet should be installed near

the equipment and be easily accessible.

GB

4

5

GB

Table of Contents

GB

Overview

Precautions .........................................6

Notes on Installation ..........................7

Unsuitable Installation ..................7

Unsuitable Conditions ..................7

Features ..............................................8

Location and Function of Controls .10

Top/Front/Left Side ....................10

Rear/Right Side/Bottom .............10

Control Panel ..............................12

Connector Panel .........................12

Remote Commander ...................13

Setting Up and Projecting

Installing the Projector .....................16

Connecting the Projector ..................17

Connecting with a Computer ......17

Connecting with a VCR or 15k

RGB/Component

Equipment .......................19

Selecting the Menu Language ..........21

Projecting .........................................23

Effective Tools for Your

Presentation .....................27

Adjustments and Settings

Using the Menu

Using the MENU .............................28

The PICTURE SETTING Menu ......29

The INPUT SETTING Menu ...........31

The SET SETTING Menu ...............32

The MENU SETTING Menu ...........33

The INSTALL SETTING Menu ..... 34

The INFORMATION Menu ............ 35

Maintenance

Maintenance .................................... 36

Replacing the Lamp ................... 36

Cleaning the Air Filter ............... 37

Troubleshooting .............................. 39

Warning Messages ..................... 41

Caution Messages ...................... 42

Other

Specifications .................................. 43

Index ............................................... 48

GB

6 Precautions

B Overview

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

• Be careful not to have your fingers caught

by the adjuster. The powered tilt adjuster

of this unit automatically extends when the

power is turned on, and is put away

automatically when the power is turned

off. Do not touch the unit while the

adjuster is in operation. Adjust the

powered tilt adjuster carefully after its

automatic operation is completed.

• Do not spread a cloth or paper under the

unit.

On illumination

• To obtain the best picture, the front of the

screen should not be exposed to direct

lighting or sunlight.

• Ceiling-mounted spot lighting is

recommended. Use a cover over

fluorescent lamps to avoid lowering the

contrast ratio.

• Cover any windows that face the screen

with opaque draperies.

• It is desirable to install the projector in a

room where floor and walls are not of

light-reflecting material. If the floor and

walls are of reflecting material, it is

recommended that the carpet and wall

paper be changed to a dark color.

On preventing internal heat build-

up

After you turn off the power with the I / 1

key, do not disconnect the unit from the wall

outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation

holes (intake) and ventilation holes

(exhaust). Do not block or place anything

near these holes, or internal heat build-up

may occur, causing picture degradation or

damage to the projector.

On cleaning

• To keep the cabinet looking new,

periodically clean it with a soft cloth.

Stubborn stains may be removed with a

cloth lightly dampened with a mild

detergent solution. Never use strong

solvents, such as thinner, benzene, or

abrasive cleansers, since these will

damage the cabinet.

• Avoid touching the lens. To remove dust

on the lens, use a soft dry cloth. Do not use

a damp cloth, detergent solution, or

thinner.

• Clean the filter at regular intervals.

On LCD data projector

• The LCD data projector is manufactured

using high-precision technology. You

may, however, see tiny black points and/or

bright points (red, blue, or green) that

continuously appear on the LCD data

projector. This is a normal result of the

manufacturing process and does not

indicate a malfunction.

7

GB

Notes on Installation

Overview

Notes on Installation

Do not install the projector in the following

situations. These installations may cause

malfunction or damage to the projector.

Poorly ventilated

• Allow adequate air circulation to prevent

internal heat build-up. Do not place the

unit on surfaces (rugs, blankets, etc.) or

near materials (curtains, draperies) that

may block the ventilation holes. When the

internal heat builds up due to the block-up,

the temperature sensor will function with

the message “High temp.! Lamp off in 1

min.” The power will be turned off

automatically after one minute.

• Leave space of more than 30 cm (11

7

/8

inches) around the unit.

• Be careful that the ventilation holes may

inhale tininess such as a piece of paper.

Highly heated and humid

• Avoid installing the unit in a location

where the temperature or humidity is very

high, or temperature is very low.

• To avoid moisture condensation, do not

install the unit in a location where the

temperature may rise rapidly.

Very dusty

Avoid installing the unit in a location where

there is a lot of dust; otherwise, the air filter

will be obstructed. The dust blocking the air

through the filter may cause raising the

internal heat of the projector. Clean it up

periodically.

Do not use the projector under the following

conditions.

Toppling the unit

Avoid using as the unit topples over on its

side. It may cause malfunction.

Tilting the unit out of the range of

the adjuster setting

Avoid using when the unit is tilted out of the

range of the adjuster setting. Such

installation may cause malfunction.

Blocking the ventilation holes

Avoid using something to cover over the

ventilation holes (exhaust/intake);

otherwise, the internal heat may build up.

For details on the ventilation holes (intake/

exhaust), see “Location and Function of

Controls” on page 10.

Unsuitable Installation

Unsuitable Conditions

GB

8 Features

Installing the unit at altitudes

Before installing the unit at altitudes higher

than 1500 m (4921 feet), consult qualified

Sony personel. Installation at such altitudes

may affect the reliability of the projector.

Features

High operability

• Intelligent Auto-setup function

Simply press the power key, and the

projector automatically performs the

setups required before use. The projector

opens the lens protector, corrects the V

Keystone, and sets optimum conditions for

projection. This function is called

Intelligent Auto-setup.

For easier operations, the keys that will be

used frequently are allocated on the top of

the projector.

Accepts various input signals

• Scan converter loaded

This projector has a build-in scan

converter that converts the input signal

within 1024 × 768 dots (VPL-CX5) or 800

× 600 dots (VPL-CS5) .

• Compatible input signals

This projector accepts video signals of

composite, S video, and component as

well as VGA, SVGA, XGA, SXGA

1)

and

SXGA+

1)

signals, which all can be

displayed.

• Compatible with six color systems

NTSC, PAL, SECAM, NTSC

4.43

2)

, PAL-

M, or PAL-N color system can be selected

automatically or manually.

Easy presentation

• Simple setup with external equipment

This projector is preset for 38 kinds

3)

(VPL-CX5) of input signals. You can

project images from an external signal

source just by connecting the equipment

with the supplied cable.

You can use the supplied Remote

Commander as the wireless mouse by

connecting the projector to the computer

with the USB cable. You can also control

the projector by using the application

software (Projector Station)

4)

supplied

with the projector from a computer

operated with Windows 98, Windows 98

SE, Windows ME, Windows 2000 or

Windows XP.

Easy-to-use Remote Commander

The Remote Commander is equipped with

various convenient keys, including the D

ZOOM key for zooming in on the image, the

FREEZE key for keeping the image

projected even if the equipment is

disconnected, and the MUTING PIC key for

muting the picture temporarily.

Memory Stick slot (VPL-CX5 only)

By inserting a Memory Stick into the built-

in Memory Stick slot, you can make the

presentation easily without connecting the

computer.

High brightness, high picture

quality

• High brightness

Adopting Sony’s unique new, high-

efficiency optical system allows the 165

W UHP lamp a light output of 2000 ANSI

lumen (VPL-CX5) or 1800 ANSI lumen

(VPL-CS5).

Note

..............................................................................................................................................................

1)The SXGA and SXGA+ signals are

available for the VPL-CX5 only.

2)NTSC

4.43 is the color system used when

playing back a video recorded on NTSC on

a NTSC

4.43 system VCR.

3) The VPL-CS5 is preset for 25 kinds of input

signals.

4)The application software (Projector Station)

can be used with the VPL-CX5 only.

9

GB

Features

Overview

•High resolution

For VPL-CX5: Three superhigh-aperture

0.7-inch XGA panels with approximately

790,000 pixels, and with micro-lens array,

provide a resolution of 1024 × 768 dots

(horizontal/vertical) for RGB input, and

750 horizontal TV lines for video input.

For VPL-CS5: Three superhigh-aperture

0.7-inch SVGA panels with

approximately 480,000 pixels provide a

resolution of 800 × 600 dots (horizontal/

vertical) for RGB input, and 600

horizontal TV lines for video input.

Quiet operation

Because the projector uses Sony’s unique

cooling mechanism, it operates more

quietly.

High portability

• Light weight/small size/simple design

This projector has been miniaturized to

approx. 2.7 kg (5 lb 15 oz) in weight and

B5-file size.

Its simple yet sophisticated design fits

comfortably in your office.

...............................................................................

• Windows is a registered trademark of

Microsoft Corporation in the United States

and/or other countries.

• IBM PC/AT, VGA, SVGA, XGA and

SXGA are registered trademarks of the

International Business Machines

Corporation, U.S.A.

• Kensington is a registered trademark of

Kensington Technology Group.

• Macintosh is a registered trademark of

Apple Computer, Inc.

• VESA is a registered trademark of Video

Electronics Standard Association.

• Display Data Channel is a trademark of

Video Electronics Standard Association.

• Memory Stick and are trademarks

of Sony Corporation.

GB

10 Location and Function of Controls

Location and

Function of Controls

1 I / 1 (on/standby) key

Turns on and off the projector when the

projector is in standby mode. The ON/

STANDBY indicator around the I / 1

key lights in green when the power is

turned on.

When turning off the power, press

the I / 1 key twice following the

message on the screen, or press and

hold the key for about two seconds.

For details on steps for turning off the

power, see “To turn off the power” on

page 26.

2 ON/STANDBY indicator (located

around the

I / 1 key)

Lights up or flashes under the following

conditions:

– Lights in red when a AC power cord is

plugged into a wall outlet. Once in

standby mode, you can turn on the

projector with the I / 1 key.

– Lights in green when the power is

turned on.

– Flashes in green while the cooling fan

runs after the power is turned off with

the I / 1 key. The fan runs for about

90 seconds after the power is turned

off.

The ON/STANDBY indicator flashes

quickly for the first 60 seconds.

During this time, you cannot light up

the ON/STANDBY indicator with the

I / 1 key.

For details on the LAMP/COVER and

the TEMP/FAN indicators, see on

page 41.

3 TILT adjustment key

For details, see“How to use the powered

tilt adjuster” on page 11.

4 INPUT key

Selects the input signal. Each time you

press the key, the input signal switches

as follows:

Top/Front/Left Side

Rear/Right Side/Bottom

TILT

1

2

3

4

5

7

8

6

9

qa

0

q

d

qg

qh

qj

q

s

qf

INPUT A t MS t VIDEO t S VIDEO

t

(VPL-CX5

only)

11

GB

Location and Function of Controls

Overview

5 Lens protector (lens cover)

The lens protector automatically opens

when the power is turned on.

6 Front remote control detector

7 Ventilation holes (exhaust)

8 Connector/Control panel

For details, see “Connector Panel” and

“Control Panel” on page 12.

9 Rear remote control detector

0 Ventilation holes (intake)

qa Lamp cover

qs Powered tilt adjuster

qd Speaker

qf Security lock

Connects to an optional security cable

(Kensington’s).

Web page address:

http://www.kensington.com/

qg Focus ring

Adjusts the picture focus.

qh Zoom ring

Adjusts the picture size.

qj Ventilation holes (intake)/air

filter cover

• Do not place anything near the

ventilation holes as it may cause

internal heat build-up.

• Do not place your hand or objects

near the ventilation holes as it may

cause the air coming out heat build-

up.

• To maintain optimal performance, clean

the air filter every 300 hours.

For details, see “Cleaning the Air

Filter” on page 37.

How to use the powered tilt

adjuster

To adjust the height

Adjust the height of the projector as follows:

1 Press the I / 1 key

The lens protector opens, and the

powered tilt adjuster rises automatically.

The adjuster stops at its previously

adjusted position.

2 Press f or F of the TILT key to adjust

the tilt of the projector.

You may press the KEYSTONE key on

the Remote Commander to display the

Tilt menu and adjust the tilt using the M/

m/</, keys.

• Be careful not to let the projector down on

your fingers.

• Do not push hard on the top of the projector

with the powered tilt adjuster out.

It may be occurred malfunction.

Notes

Powered tilt

adjuster

TILT

to lower the

projector

to raise the

projector

TILT adjustment key

GB

12 Location and Function of Controls

1 POWER SAVING indicator

Lights up when the projector is in power

saving mode. When “Power Saving” in

the SET SETTING menu is set to “ON,”

the projector goes into power saving

mode if no signal is input for 10 minutes.

Although the lamp goes out, the cooling

fan keeps running. The power saving

mode is canceled when a signal is input

or any key is pressed. In power saving

mode, any key does not function for the

first 60 seconds after the lamp goes out.

2 MENU key

Displays the on-screen menu. Press

again to clear the menu.

3 Arrow keys (f/F/g/G)

Select the menu or to make various

adjustments.

4 ENTER key

Enters the settings of items in the menu

system.

5 TEMP (Temperature)/FAN

indicator

Lights up or flashes under the following

conditions:

– Lights up when temperature inside the

projector becomes unusually high.

– Fashes when the fan is broken.

For details, see page 41.

6 LAMP/COVER indicator

Lights up or flashes under the following

conditions:

– Lights up when the lamp has reached

the end of its life or becomes a high

temperature.

– Flashes when the lamp cover or air

filter cover is not secured firmly.

For details, see page 41.

1 INPUT A connector (HD D-sub

15-pin, female)

Connect to external equipment such as a

computer.

Connects to the monitor output on a

computer using the supplied cable.

When inputting a component or 15k

RGB signal, use an optional cable.

For details, see “To connect a 15k RGB/

Component equipment” on page 20.

2 USB connector (USB plug for

upstream, 4-pin)

Connect to the USB connector on a

computer. When you connect the

projector to the computer, you can

Control Panel

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

PUSH

ENTER

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

PUSH

ENTER

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

1

2

3

4

65

Connector Panel

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

PUSH

ENTER

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

1

2

3

4

5

6

7

13

GB

Location and Function of Controls

Overview

control the mouse function with the

supplied Remote Commander. The

supplied application software (VPL-

CX5 only) can be installed in the

computer attached to this connector.

3 Memory Stick slot (VPL-CX5

only)

The Memory Stick can be inserted.

Never insert an object other than the

Memory Stick.

For details, see the attached “Operating

Instructions” for Memory Stick.

4 AUDIO (stereo minijack)

connector

When listening to sound output from the

computer, connect to the audio output of

the computer.

When listening to sound output from the

VCR, connect to the audio output of the

VCR.

5 Access lamp

Lights during having access to the

Memory Stick.

Do not remove the Memory Stick

while the access lamp is lit.

6 Video input connector

Connect to external video equipment

such as a VCR.

• VIDEO (phono type): Connects to

the composite video output of video

equipment.

• S VIDEO (mini DIN 4-pin):

Connects to the S video output (Y/C

video output) of video equipment.

7 AC IN socket

Connects the supplied AC power cord.

The keys that have the same names as those

on the control panel function identically.

1 I / 1 (on/standby) key

2 APA (Auto Pixel Alignment) key

Adjusts a picture clearest automatically

while a signal is input from a computer.

Used when “Smart APA” in the SET

SETTING menu is set to “Off.”

Normally set to “On.”

• Press the APA key when the full image

is displayed on the screen. If there are

black edges around the image, the APA

function will not function properly and

the image may extend beyond the screen.

Remote Commander

Notes

I / 1

INPUT

PIC

FREEZE

MENU ENTER

KEYSTONE

MUTING

MS SLIDE

RESET

FUNCTION

D ZOOM

12

APA

+

–

R

CLICK

9

2

3

4

6

7

1

8

qa

qf

q

g

qd

qs

0

5

a

5

b

5

c

GB

14 Location and Function of Controls

• You can cancel the adjustment by

pressing the APA key again while

“Adjusting” appears on the screen.

• The picture may not be adjusted properly

depending on the kinds of input signals.

• Adjust the items “Dot Phase,” “H Size”

and “Shift” in the INPUT SETTING

menu when you adjust the picture

manually.

3 PIC MUTING key

Used to mute the picture temporarily.

Press again to restore the picture.

4 ENTER key

5 Keys emulate a mouse

Functions like a mouse of a computer

connected via USB with the projector.

a) L Click key (Rear): Functions as

the left button on a mouse.

b) Joystick

c) R Click key: Functions as the right

button on a mouse.

These keys function as mouse buttons of a

computer only when the projector is

connected to the computer using the USB

cable.

For details, see “To control the

computer using the supplied Remote

Commander” on page 25.

6 FUNCTION 1, 2 keys (VPL-CX5

only)

When you connect the projector with a

computer, you can open a file on the

screen by just pressing the FUNCTION

key. This will enhance your

presentation. To use this function,

allocate a file to the FUNCTION key by

using the supplied application software.

For details, see the README file and

the HELP file supplied with the

application software.

Connect a computer to the projector using

the USB cable to activate the FUNCTION

keys.

For details, see “To connect an IBM PC/

AT compatible computer” on page 18”.

7 RESET key

Resets the value of an item back to its

factory preset value or returns the

enlarged image back to its original size.

This key functions when the menu or a

setting item is displayed on the screen.

8 D ZOOM (Digital Zoom) +/– key

Enlarges the image at a desired location

on the screen.

+:Pressing the + key once displays the

icon. This icon indicates the point you

want to enlarge. Use an arrow key (M/

m/</,) to move the icon to the

point to be enlarged. Press the + key

repeatedly until the image is enlarged

to your requirements.

–: Pressing the – key reduces an image

that has been enlarged with the D

ZOOM + key.

9 Arrow keys (M/m/</,)

0 MENU key

qa KEYSTONE key

Used to adjust the tilt of the projector, or

the trapezoidal distortion of the image

manually. Each time you press this key,

the Tilt menu and the V Keystone menu

is displayed alternately. Use the arrow

keys (M/m/</,) for the adjustment.

qs INPUT key

qd FREEZE key

Used to freeze the picture projected. To

cancel the frozen picture, press the key

again.

qf MS SLIDE key (VPL-CX5 only)

Used to execute the slide show. When

the input signal is other than MS, it

switches to MS. To begin the slide show,

press the key again.

qg Infrared transmitter

Note

15

GB

Location and Function of Controls

Overview

To install batteries

1 Push and slide to open the lid, then

install the two size AA (R6) batteries

(supplied) with the correct polarity.

2 Replace the lid.

Notes on batteries

• Make sure that the battery orientation is

correct when inserting batteries.

• Do not mix an old battery with a new one

or different types of batteries.

• If you do not use the Remote Commander

for a long time, remove the batteries to

avoid damage from battery leakage. If

batteries have leaked, remove them, wipe

and dry the battery compartment, and

replace the batteries with new ones.

Notes on Remote Commander

operation

• Make sure that nothing obstructs the

infrared beam between the Remote

Commander and the remote control

detector on the projector. Direct the

Remote Commander toward the front or

rear remote control detector.

• The operation range is limited. The shorter

the distance between the Remote

Commander and the projector is, the wider

the angle within which the commander can

control the projector becomes.

Be sure to install the battery

from the

# side.

While pressing the lid, slide it.

GB

16 Installing the Projector

B Setting Up and Projecting

Installing the Projector

This section describes how to install the projector.

The distance between the lens and the screen varies depending on the size of

the screen. Use the following table as a guide.

There may be a slight difference between the actual value and the design value shown

in the table above.

Unit: m (feet)

Screen size

(inches)

40 60 80 100 120 150

Minimum

Distance

1.5

(4.9)

2.3

(7.5)

3.1

(10.2)

3.9

(12.8)

4.7

(15.4)

5.9

(19.4)

Maximum

Distance

1.9

(6.2)

2.9

(9.5)

3.8

(12.5)

4.8

(15.7)

5.7

(18.7)

7.2

(23.6)

Distance between the screen and

the center of the lens

17

GB

Connecting the Projector

Setting Up and Projecting

Connecting the Projector

When you connect the projector, make sure to:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs firmly; loose connections may increase noise and

reduce performance of picture signals. When pulling out a cable, be sure to

pull it out from the plug, not the cable itself

To connect the projector, refer to the illustrations on the next and the

following pages.

This section describes how to connect the projector to a computer.

For more information, refer to the computer’s instruction manual.

• The projector accepts VGA, SVGA, XGA, SXGA (VPL-CX5 only) and SXGA+

(VPL-CX5 only) signals. However, we recommend that you set the output mode of

your computer to XGA mode (VPL-CX5) or SVGA mode (VPL-CS5) for the external

monitor.

• If you set your computer, such as a notebook type, to output the signal to both your

computer’s display and the external monitor, the picture of the external monitor may

not appear properly. Set your computer to output the signal to only the external

monitor.

For details, refer to the computer’s operating instructions supplied with your

computer.

• This projector is compatible with a DDC2B (Digital Data Channel 2B). If your

computer is compatible with a DDC, turn the projector on according to the following

procedures.

1 Connect the projector to the computer by using the supplied HD D-sub 15 pin cable.

2 Turn the projector on.

3 Start the computer.

Connecting with a Computer

Notes

GB

18 Connecting the Projector

To connect an IBM PC/AT compatible computer

On the USB function

When connecting the projector to a computer by using the USB cable for the

first time, the computer recognizes the following devices automatically.

1 USB hub (general use) (VPL-CX5 only)

2 USB human interface device (wireless mouse function)

3 USB human interface device (projector control function) (VPL-CX5 only)

Recommended operating environment

When you use the USB function, connect the USB cable as illustrated above.

This application software and the USB function can be used on a computer

loaded with Windows 98, Windows 98 SE, Windows ME, Windows 2000 or

Windows XP preinstall models.

• Your computer may not start correctly when connected to the projector via the USB

cable. In this case, disconnect the USB cable, restart the computer, then connect the

computer to the projector using the USB cable.

• This projector is not guaranteed for suspend, standby mode. When you use the

projector in suspend, standby mode, disconnect the projector from the USB port on

the computer.

• Operations are not guaranteed for all the recommended computer environments.

To connect a Macintosh computer

To connect a Macintosh computer equipped with video output connector of a

type having two rows of pins, use a commercially available plug adaptor.

When you connect a USB capable Macintosh computer using the USB cable

to the projector, wireless mouse functions become available.

The supplied software does not run on Macintosh computer.

Notes

Note

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

PUSH

ENTER

to USB connector

Left side

HD D-sub 15-pin cable

(supplied)

Stereo audio connecting cable (not supplied)

a)

to monitor output

Computer

USB cable (supplied)

to audio output

a) Use a no-resistance cable.

(Connect the USB cable to use a wireless

mouse or the Projector Station.)

19

GB

Connecting the Projector

Setting Up and Projecting

This section describes how to connect the projector to a VCR and 15k RGB/

component equipment.

For more information, refer to the instruction manuals of the equipment you

are connecting.

To connect a VCR

Connecting with a VCR or 15k RGB/Component Equipment

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

PUSH

ENTER

Stereo audio connecting cable

(not supplied)

a)

VCR

to S

video

output

Left side

to audio

output

Video cable (not supplied) or S-Video cable

(not supplied)

to video output

a) Use a no-resistance cable.

GB

20 Connecting the Projector

To connect a 15k RGB/Component equipment

• Set the aspect ratio using “Wide Mode” in the INPUT SETTING menu according to

the input signal.

• When you connect the unit to 15k RGB or component video equipment, select video

GBR or component with the “Input-A Signal Sel.” setting in the SET SETTING

menu.

• Use the composite sync signal when you input the external sync signal from 15k

RGB/component equipment.

Notes

ACCESS

AUDIO VIDEO

POWER

SAVING

MENU

S VIDEO

TEMP/FAN

LAMP/COVER

INPUT A

PUSH

ENTER

Left side

Stereo audio connecting cable

(not supplied)

a)

SMF-402 Signal Cable

(not supplied)

HD D-sub 15-pin (male) ↔ 3 × phono jack

to audio

output

15k RGB/Component equipment

to RGB/

component

output

a) Use a no-resistance cable.

La page charge ...

Sony VPL-CS5 Manuel utilisateur

Ce manuel convient également à

Sony VPL-CS5 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents