KitchenAid KBSS271TSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBSS271TSS0

Taper: Le manuel du propriétaire

OUTDOOR GRILLS

BUILT-IN INSULATED JACKET GRILLS

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.Kitchenaid.ca

GRILS D'EXTÉRIEUR

GRILS ENCASTRÉS AVEC CHEMISAGE ISOLÉ

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777

ou visitez notre site web à www.Kitchenaid.ca

Table of Contents/Table des matières.............................................................................2

Models/Modèles KBSS271T, KBSS361T, KBSU367T, KBSU487T

W10138384C

IMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

IMPORTANT :

À conserver pour consultation par l'inspecteur local des installations électriques.

Installateur : Remettre les instructions d'installation au propriétaire.

Propriétaire : Conserver les instructions d'installation pour référence ultérieure.

TABLE OF CONTENTS

OUTDOOR GRILL SAFETY............................................................3

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................5

Product Dimensions.....................................................................5

Built-In Outdoor Grill Enclosure...................................................5

Cabinet Cutout Dimensions.........................................................6

Electrical Requirements ...............................................................8

Gas Supply Requirements...........................................................9

Gas Connection Requirements..................................................10

INSTALLATION INSTRUCTIONS................................................11

Unpack Grill................................................................................11

Make Gas Connection ...............................................................11

Plug in Grill .................................................................................12

Conversion to LP Gas ................................................................12

Check and Adjust the Burners...................................................13

OUTDOOR GRILL USE ................................................................15

Using Your Outdoor Grill............................................................15

Using Your Infrared Sear Burner................................................16

Using Your Rotisserie.................................................................17

Rotisserie Cooking Tips .............................................................18

Using Your Smoker Box ............................................................19

Hood Lights................................................................................19

TIPS FOR OUTDOOR GRILLING ...............................................19

Cooking Methods.......................................................................20

Grilling Chart...............................................................................20

OUTDOOR GRILL CARE .............................................................22

Changing the Light Bulb ............................................................22

General Cleaning........................................................................22

TROUBLESHOOTING ..................................................................24

ASSISTANCE OR SERVICE.........................................................24

In the U.S.A. ...............................................................................24

Accessories................................................................................24

In Canada ...................................................................................25

WARRANTY ..................................................................................25

TABLE DES MATIÈRES

SÉCURITÉ DU GRIL D'EXTÉRIEUR ...........................................27

EXIGENCES D'INSTALLATION...................................................29

Outillage et pièces......................................................................29

Exigences d'emplacement.........................................................29

Dimensions du produit...............................................................30

Enceinte du gril d'extérieur encastré .........................................30

Dimensions de l'ouverture à découper dans le placard............31

Spécifications électriques ..........................................................33

Spécifications de l'alimentation en gaz .....................................34

Exigences concernant le raccordement au gaz ........................35

INSTRUCTIONS D’INSTALLATION.............................................36

Déballage du gril.........................................................................36

Raccordement au gaz................................................................36

Branchement du gril...................................................................37

Conversion pour l'alimentation au propane...............................38

Contrôle et réglage des brûleurs................................................38

UTILISATION DU GRIL D'EXTÉRIEUR.......................................40

Utilisation du gril d'extérieur.......................................................40

Utilisation du brûleur à infrarouge..............................................42

Utilisation du tournebroche........................................................42

Conseils de cuisson à l’aide du tournebroche ..........................43

Utilisation du fumoir ...................................................................44

Lampes sous le capot................................................................44

CONSEILS POUR L'UTILISATION DU GRIL D'EXTÉRIEUR ...44

Méthodes de cuisson.................................................................45

Tableau de cuisson au gril .........................................................45

ENTRETIEN DU GRIL D'EXTÉRIEUR .........................................48

Changement de l'ampoule d'éclairage......................................48

Nettoyage général ......................................................................48

DÉPANNAGE.................................................................................50

ASSISTANCE OU SERVICE.........................................................51

Accessoires ................................................................................51

GARANTIE.....................................................................................51

OUTDOOR GRILL SAFETY

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2000 ft (609.6 m) orifice

conversion is required. See “Gas Supply Requirements” section. It is the responsibility of the installer to comply with the minimum

installation clearances specified on the model/serial rating plate. The model/serial rating plate for built-in models can be found on the

right-hand side of the grill. The model/serial rating plate for freestanding models can be found on the right-hand inside cabinet wall.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

DANGER

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

Parts Needed

■ Gas line shutoff valve

■ ½" male pipe thread nipple for connection to pressure

regulator

■ Pipe-joint compound resistant to LP gas

■ CSA design-certified outdoor flexible stainless steel

appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply

line as needed.

Parts Supplied

■ Convertible regulator set for 4" WCP Natural gas.

■ 1 single-prong plug/500 mAmp transformer assembly, on

some models

■ 1 single-prong plug/5,000 mAmp transformer assembly

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

■

Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

■

Always maintain minimum clearances from combustible

construction, see “Location Requirements” section.

■

The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

■

This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

■

Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

■

Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

■

Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

■

Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

■

Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

■

Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

■

The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

■

Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

“Installation Instructions” section.

■

When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

■

Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

■

Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

■

The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

■

Gas cylinder must include a collar to protect the cylinder

valve.

■

For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

■

Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

■

Never fill the cylinder beyond 80 percent full.

■ Tape measure

■ Small, flat-blade screwdriver

■ Flat-blade screwdriver

■ #2 and #3 Phillips screwdriver

■ Level

■ Wrench or pliers

■ Pipe wrench

■ Scissors or cutting pliers

(to remove tiedowns)

■ Noncorrosive

leak-detection solution

Additional Parts Supplied (on some models)

■ 1.5-volt “D” size alkaline battery

■ Rotisserie motor mounting bracket

■ Rotisserie motor

■ Rotisserie forks

■ Rotisserie spit

■ Smoker box

Location Requirements

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for built-in and

freestanding outdoor grills:

■ A minimum of 24" (58.0 cm) must be maintained between the

front of the grill hood, sides and back of the grill and any

combustible construction.

■ A zero clearance may be maintained on the insulated jacket

surface to combustible construction.

Rotisserie

A 6" (15.2 cm) minimum clearance is needed for the rotisserie

motor.

A grounded, 3-prong outlet located to the left of the grill is

required. See “Electrical Requirements” section.

Product Dimensions

Built-In Outdoor Grill Enclosure

This built-in outdoor grill is only for installation in a built-in

enclosure constructed of combustible and non-combustible

materials. Some types of non-combustible materials could be

brick, firewall or steel. Some types of combustible materials

could be wood or laminate.

The enclosure for the built-in outdoor grill is to be a minimum

of 11¾" [29.8 cm] high x 24" [61.0 cm] deep x (33" [83.8 cm] for

27" [68.6 cm] grill and 42" [106.7 cm] for 36" [91.4 cm] grill and

54" [137.2 cm] for 48" [121.9 cm] grill) wide.

WARNING

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

A. 27" (68.6 cm)

36" (91.4 cm)

48" (121.9 cm)

B. 27" (68.6 cm) models - 32

⁷⁄₈

" (83.3 cm)

36" (91.4 cm) models - 41

⁷⁄₈

" (106.2 cm)

48" (121.9 cm) models - 53

⁷⁄₈

" (136.6 cm)

25⁵⁄₈"

(65.0 cm)

38"

(96.5 cm)

27¾"

(70.5 cm)

23⁷⁄₈"

(60.5 cm)

11¾"

(29.8 cm)

Cabinet Cutout Dimensions

The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code,

ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.

Copies of the standards listed may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

NOTE: The grill drops into the opening and the bottom of the grill should be supported by the bottom support of the cabinet cutout.

The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor

products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and

minimum spacing must be followed.

20⁵⁄₈" (52.4 cm)

1¹⁄₂"

(3.8 cm) min.

3" (7.6 cm) min.

to open hood

2¹⁄₂" (6.4 cm) min.

12" (30.5 cm) min.

to any accessory

12" min.

to any

accessory

20⁷⁄₈" (53.0 cm)

9¹⁄₈"

(23.2 cm)

(12.7 cm) min.

Grills or

Refreshment Centers

Side

Sear

Burners

Warming

Drawer

Access Doors

Refrigerator

Ice Maker

Utility

Trash

Drawer

Minimum Spacing Requirement Between Cutouts - Dimension K

Between 2 or more sets of Access Doors adjacent to each other:

K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a Trash Drawer, Utility Drawer, or Warming Drawer:

K = 3" (7.6 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Cabinet Height and Depth Dimensions

Dimension A Minimum Dimension B Minimum

With outdoor refrigerator 37" (94.0 cm) 26" (66.0 cm)

Grill with insulated jacket 36½" (92.7 cm) 27" (68.6 cm)

Grill without insulated jacket 35½" (90.2 cm) 26" (66.0 cm)

Cutout Dimensions - Built-in Grill

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 29⁵⁄₈" (75.2 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm)

36" (91.4 cm) 38⁵⁄₈" (98.1 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm)

48" (121.9 cm) 50⁵⁄₈" (128.6 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm)

Cutout Dimensions - Built-in Grill with Insulated Jacket

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 33" (83.8 cm) 11¾" (29.8 cm) 24" (61.0 cm)

36" (91.4 cm) 42" (106.7 cm) 11¾" (29.8 cm) 24" (61.0 cm)

48" (121.9 cm) 54" (137.2 cm) 11¾" (29.8 cm) 24" (61.0 cm)

Cutout Dimensions - Built-in Side Burner

Burner Position Dimension C Dimension D Dimension E

Front to Back 13½" (34.3 cm) 10¾" (27.3 cm) 22⁵⁄₈" (57.5 cm)

Side by Side 24½" (62.2 cm) 10¾" (27.3 cm) 16⁷⁄₈" (42.9 cm)

Cutout Dimensions - Built-in Sear Burner

Dimension C Dimension D Dimension E

13½" (34.3 cm) 10⁵⁄₈" (27.0 cm) 22¹¹⁄₁₆" (57.6 cm)

Cutout Dimensions - Built-in Refreshment Center

Dimension C Dimension D Dimension E

30½" (77.5 cm) 10¾" (27.3 cm) 23" (58.4 cm)

Cutout Dimensions - Built-in Access Doors

Door Size Dimension F Dimension L*

18" (45.7 cm) 16³⁄₁₆" (41.1 cm) 1½" (3.8 cm)

27" (68.6 cm) 25¹⁄₈" (63.8 cm) 1½" (3.8 cm)

30" (76.2 cm) 28¹⁄₈" (71.4 cm) 1½" (3.8 cm)

36" (91.4 cm) 34¹⁄₈" (86.7 cm) 1½" (3.8 cm)

48" (121.9 cm) 46¹⁄₈" (117.2 cm) 1½" (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Built-in Outdoor Grill Enclosure Ventilation for LP Gas:

An enclosure for an LP gas fuel tank is to be ventilated by

openings at both the top and lower levels of the enclosure.

If converting to LP gas these vents are to be in the enclosure:

An enclosure for use with an LP gas fuel tank for built-in

installation is to have at least one ventilation opening on an

exposed exterior side located within 5" (12.7 cm) of the top is to

be a minimum of 20 in.

(129.0 cm

). One ventilation opening

within 1" (2.5 cm) of the bottom of the enclosure and the bottom

opening is to be a minimum of 10 in.

(64.5 cm

). All vent

openings are to be unobstructed. Every opening is to be a

minimum of ¹⁄₈" (0.32 cm) wide.

Electrical Requirements

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

grill is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that a separate circuit servicing only this grill

be provided.

Cutout Dimensions - Outdoor Refrigerator

Dimension G Dimension H

24" (61.0 cm) 35¼" (89.5 cm)

Cutout Dimensions - Outdoor Ice Maker

Dimension G Dimension H

18" (45.7 cm) 34" (86.4 cm) min. to 34½" (87.6 cm) max.

Cutout Dimensions - Built-in Warming Drawer

Warming Drawer Size Dimension J

24" (61.0 cm) 22½" (57.2 cm)

Cutout Dimensions - Built-in Utility Drawer and Built-in Trash Drawer

Dimension M Dimension L*

12¼" (31.1 cm) 1½" (3.8 cm)

10 in.

(64.5 cm

) min.

ventilation both sides

5" (12.7 cm) max.

1" (2.5 cm) max.

20 in.

(129.0 cm

) min.

ventilation both sides

5" (12.7 cm) max.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

The model/serial number rating plate is located on the right-hand

side of the grill. See the following illustration.

Recommended Ground Method

The outdoor grill, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code ANSI/NFPA 70, or Canadian

Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

Gas Supply Requirements

Observe all governing codes and ordinances.

IMPORTANT: The installation of this grill must conform with local

codes or, in the absence of local codes, with either the National

Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and Handling

Code, B149.2.

IMPORTANT: Grill must be connected to a regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kits specified by the manufacturer must be used.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used.

The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Set pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Set pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

A. Model/serial number plate

A. 3-prong ground plug

B. 3-prong polarized type outdoor outlet

C. Ground prong

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor”

gas supply line.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 11” (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required for elevations above 2,000 ft (609.6 m).

See “Assistance or Service” section to order High Altitude

Conversion Kit.

Gas Supply Line Pressure Testing

Testing above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures greater than ½ psig (3.5 kPa).

Testing below ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge) or

lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than ½ psig (3.5 kPa).

Gas Connection Requirements

Natural Gas

Built-in grill models are equipped for use with Natural gas. They

are design-certified by CSA International for LP (propane) gases

with appropriate conversion.

Built-in models are set for Natural gas use and have a pressure

regulator with ½" female pipe threads.

The supply line shall be equipped with an approved shutoff valve.

This valve should be located in the same area as the grill and

should be in a location that allows ease of opening and closing.

Do not block access to the shutoff valve. The valve is for turning

on or shutting off gas to the grill.

LP Gas Conversion Using a Local LP Gas Supply

Conversion must be made by a qualified person. The installation

of this grill must conform with local codes or, in the absence of

local codes, with either the National Fuel Gas Code, ANSI

Z223.1/NPFA 54, Natural Gas and Propane Installation Code,

CSA B149.1, or Propane Storage and Handling Code, B149.2.

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

LP Gas Conversion Using a 20 lb LP Gas Fuel Tank

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

A 20 lb LP gas fuel tank must be purchased separately.

A. Grill gas pipe

B. New CSA International approved

“outdoor” flexible gas supply line

C. Rear of grill

D. To Natural gas supply

A. Gas supply line

B. Shutoff valve “open” position

C. To grill

A. Grill gas pipe

B. New CSA International approved

“outdoor” flexible gas supply line

C. Rear of grill

D. To local LP gas supply

INSTALLATION INSTRUCTIONS

Unpack Grill

■ Unpack grill. Remove all packaging materials and remove grill

from carton.

■ Move grill close to desired outdoor location.

■ Open the hood.

Remove Packaging Material Inside the Grill

1. Cut the tiedowns holding the grates together.

2. Remove rotisserie skewer (on some models), warming shelf

and grill grates from inside the grill and remove packaging

material.

3. Remove foam block and wrap from inside the grill.

4. Replace the grill grates.

5. Place warming shelf on brackets as shown.

6. On some models, install rotisserie mounting bracket using

2 screws.

7. Dispose of/recycle all packaging material.

Make Gas Connection

NOTE: If grill has been converted to LP gas, follow instructions in

“Conversion to LP Gas” at the end of this section.

Natural Gas Use

The installation of this grill must conform with local codes or, in

the absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and Handling

Code, B149.2.

1. Place grill into outdoor enclosure, but leave enough room in

back to connect to gas supply and electrical plug-in.

2. Make gas connections.

A combination of pipe fittings must be used to connect the

grill to the existing gas line.

A. Foam block

B. Foam wrap

A. Warming shelf brackets

B. Warming shelf

Excessive Weight Hazard

Use two or more people to move and install grill.

WARNING

Failure to do so can result in back or other injury.

A. 2 screws

B. Rotisserie bracket

A B

WARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor”

gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death, explosion, or fire.

■ If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA

International, to connect the grill to the rigid gas supply

line. A ⁵⁄₈" diameter line is recommended. Using a wrench

to tighten, connect the gas supply to the grill. Use pipe-

joint compound on all non-flared male threads. Do not

kink or damage the flexible connector when moving the

grill.

■ Pipe-joint compounds suitable for use with Natural gas

must be used. Do not use Teflon

tape.

3. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

Plug in Grill

1. This built-in outdoor grill comes with a 5,000 mAmp power

transformer plug assembly for the grill lights and igniter. Plug

in the single-prong plug in the receptacle on the left

underside of the grill.

2. Plug into a grounded 3-prong outlet.

3. Gently slide grill completely into outdoor enclosure.

4. Now go to the “Check and Adjust the Burners” section.

Conversion to LP Gas

(If LP gas conversion is desired)

IMPORTANT: If LP gas conversion is desired, follow

requirements outlined in the “Gas Connection Requirements”

section.

IMPORTANT: A 20 lb LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the conversion kit must be used. Replacement gas

pressure regulator/hose assembly specific to your model, is

available from your outdoor grill dealer.

A. Grill gas pipe

B. New CSA International approved

“outdoor” flexible gas supply line

C. Rear of grill

D. To Natural gas supply

A. Closed valve

B. Open valve

A. Single-prong plug

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Use a new CSA International approved “outdoor”

gas supply line.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 11” (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

To Install the 20 lb LP Gas Fuel Tank:

1. Install the 20 lb LP gas fuel tank tray according to the

instructions provided with the LP Gas Conversion Kit, Part

Number W10118099.

2. Place the 20 lb LP gas fuel tank bottom collar into the

mounting hole in the LP tank tray.

3. Tighten the locking screw against the bottom collar of the

20 lb LP gas fuel tank to secure.

4. Screw the gas pressure regulator/hose assembly to the 20 lb

LP gas fuel tank as shown.

5. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

6. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

7. Go to “Check and Adjust the Burners” section.

Check and Adjust the Burners

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary.

It is recommended that a qualified person make burner

adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing

the grate and sear plates.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is

set to HI setting are acceptable as long as no carbon or soot

deposits appear.

Check that burners are not blocked by dirt, debris, insect nests,

etc. and clean as necessary. If they are clean, adjust air shutters

as needed.

IMPORTANT: Before adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. Remove grill grates and sear plates.

A. Bottom collar

B. Mounting hole

C. Locking screw

A. 20 lb LP gas fuel tank

B. Gas pressure regulator/hose assembly

5. Remove the 2 screws that hold the burner in place. Remove

gas burner from the grill.

6. If flame is yellow (not enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn

air shutter adjustment screw clockwise.

Adjustment should be made clockwise or counterclockwise

from ¹⁄₈" (3.2 mm) to ¹⁄₄" (6.4 mm).

7. Replace gas burner, sear plates and grates.

8. Light grill using information in the “Outdoor Grill Use” section.

See “Burner Flame Characteristics.”

Low Flame Adjustment

If flame goes out on the “LO” setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and sear plates.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting and remove knob.

5. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

6. Watch the flame and slowly turn the screwdriver

counterclockwise.

7. Adjust flame to minimum stable flame.

8. Replace the control knob and turn off the burner.

9. Repeat steps 3 through 8 for each burner if needed.

10. Replace the sear plates and grates after the burners have

cooled.

A. 2 screws

A. Air shutter adjustment screw

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

OUTDOOR GRILL USE

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and

appearances of the features shown here may not match those of your model.

Control Panel

Using Your Outdoor Grill

Prepare the Gas Supply

1. Open the hood completely. Do not light burners with the hood

closed.

2. Make sure control knobs are turned to OFF. The drip pan

must be in place and pushed all the way to the back.

A. Left rotisserie burner control knob

B. Left grill burner control knob

C. Center grill burner control knob

D. Right grill burner control knob

E. Hood lights switch

F. Sear b urner c on tro l knob

G. Right rotisserie burner control knob

H. Front side burner control knob

I. Rear side burner control knob

C D

H I

LIGHTS

WARNING

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

A. Drip pan

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

Turn the Gas Supply On

1. For outdoor grills using gas supply source other than 20 lb LP

gas fuel tank:

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

2. For outdoor grills using a 20 lb LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your grill may not

light. If your grill does light, the flames will be low and will not

heat properly. Turn tank valve and all control knobs off and

wait 30 seconds. After shutting off the tank, very slowly open

tank valve and wait 5 seconds before lighting.

Lighting the Grill and Infrared Sear Burner

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

1. Do not lean over the grill.

2. Select the burner you want to light. Push in and turn the grill

burner control knob to LITE/HI, while continuing to hold it in.

3. Surface Ignition Type Burners:

You will see the igniter glow. When burner is lit, release the

knob. Turn knob to desired setting.

Spark Ignition Type Burners:

You will hear the “snapping” sound of the spark. When burner

is lit, release the knob. Turn knob to desired setting.

4. Repeat for each of the other burners as needed.

Manually Lighting Main Grill and Infrared Sear Burners

1. Do not lean over the grill.

2. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

3. Strike the match to light it.

4. Guide the lit match between the grill grate and one of the

slots in the sear plate.

5. Push in and turn the burner knob to LITE/HI for the burner

closest to the lit match. The burner will light immediately.

When burner is lit, turn knob to desired setting.

6. Repeat steps 2 through 5 for each main burner.

7. Remove match and replace manual lighting extension inside

the cabinet drawer.

IMPORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to light them manually,

contact the KitchenAid Customer eXperience Center. See the

“Assistance or Service” section.

Using Your Infrared Sear Burner

(on some models)

Infrared grilling produces intense heat which quickly sears the

meat. Searing locks in flavor and juices while allowing the outer

surface to absorb smoke and food aroma that is produced as

grease and drippings are vaporized by the burner. The result is a

crisp, flavorful outside with a tender, juicy inside.

■ Preheat the infrared sear burner for 5 minutes.

■ Ensure that meats are fully thawed and that all excess fat is

trimmed away prior to grilling.

■ Leave the burner set to HI when placing food on the grill to

sear.

■ Use the sear burner to sear meat 1 to 2 minutes on each side,

then move the meat to the main grill cooking surface to finish

grilling to the desired doneness.

A. Closed valve

B. Open valve

Right-hand side flange

NOTE: View is shown with grates removed. Grates are

to be in place when using the infrared sear burner.

Using Your Rotisserie

For best cooking results, do not use main grill burners when

using the rotisserie.

The rotisserie system is designed to cook food from the rear

using intense, searing infrared heat.

NOTE: To avoid product damage when not using the rotisserie,

remove motor and store indoors. Remove spit rod and forks.

Store out of reach of children.

To Use:

1. Remove warming shelf.

2. Mount rotisserie motor on the rotisserie’s mounting bracket.

Position it securely into support bracket slots. Plug in the

single-prong plug of the 500 mAmp transformer assembly

into rotisserie motor.

3. To load the spit rod, slide one of the rotisserie forks onto the

spit rod with prongs facing inward.

4. Push spit rod through the center of the food, then slide

second rotisserie fork into position.

5. Center the food and rotisserie forks on spit rod and tighten

wing nuts on the rotisserie forks. If necessary, secure loose

food portions with butcher’s string.

6. Once the food is positioned on spit rod, place pointed end of

rod through the hole in the left side of the grill and into the

rotisserie motor, then lower the notched end of the spit rod

onto the support bracket on the opposite side.

7. Check that food is centered with the rotisserie burner. If not,

loosen wing nuts, reposition food and retighten wing nuts.

8. Plug into a grounded 3 prong outlet.

9. Turn on the rotisserie motor and light the rotisserie burner.

See the following “Lighting the Rotisserie Burner” section.

Lighting the Rotisserie Burner

IMPORTANT: If the rotisserie burner does not light immediately,

turn the rotisserie burner knob to OFF and wait 5 minutes before

relighting.

1. Do not lean over the grill.

2. Push in and turn the control knob to LITE/HI.

Surface Ignition Type Burners:

You will see the igniter glow.

Spark Ignition Type Burners:

Your will hear the “snapping” sound of the spark.

3. When the rotisserie burner lights, continue to hold the knob in

for another 10 seconds, then release the knob and burner will

stay lit.

Manually Lighting the Rotisserie Burner

IMPORTANT: If the rotisserie burner does not light immediately,

turn the rotisserie burner knob to OFF and wait 5 minutes before

relighting.

1. Do not lean over the grill.

A. Rotisserie motor

B. Spit rod

C. Rotisserie fork

D. Rotisserie burner

A. Rotisserie motor

B. 500 mAmp single-prong power cord

A. Pointed end of spit rod

B. Notched end of spit rod

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

2. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

3. Strike the match to light it.

4. Gently hold the lit match close to the rotisserie burner.

5. Push in and turn the control knob to LITE/HI. Hold this knob

in for 10 seconds after the burner is lit.

Surface Ignition Type Burners:

You will see the igniter glow until after the knob is released.

Spark Ignition Type Burners:

You will hear the “snapping” sound of the spark until after the

knob is released.

6. Remove the match and replace the manual lighting extension

inside the cabinet drawer.

Rotisserie Cooking Tips

Rotisserie cooking rotates food in front of the rotisserie burner,

creating an intense heat for searing the outside and sealing in

natural juices.

The rotisserie burner reaches cooking temperatures in about

1 minute. It is not necessary to preheat when using the rotisserie.

■ Select tender meat and poultry.

■ Allow at least 1" (2.5 cm) space between rotisserie burner

and the food.

■ To make cleanup easier, place a pan under the food to catch

drippings.

■ The hood can be opened or closed, but when using the

rotisserie with the smoker the hood should be closed.

■ Add barbecue sauce or glaze only during the last 10 minutes

of cooking to keep sauce from burning.

Trussing Poultry for the Rotisserie

1. Load the spit rod by sliding one of the forks on the rod, with

the prongs facing inward. Tighten the screw to keep it from

slipping.

2. Push the rod through the center of the bird.

3. Cut 24" (61 cm) of butcher’s string and center it under the

bird, breast side up.

4. Wrap each end of the string around the wings; catch each

wing tip. Bring the string tightly together at the top of the

breast and knot. It is not necessary to cut off the extra string.

5. Cut another 20" (50.8 cm) of string and lay it under the back

of the bird. Wrap it around the tail then around the spit rod,

cinching tightly.

6. Cross the legs on top of spit rod; tie string around the

crossed legs.

7. Connect the twine holding the legs, to the string holding the

wings, and knot. Cut off any bits of hanging string.

8. Slide on the second fork pushing the tines into the

drumsticks.

9. Center the food and forks on the rod and tighten the thumb-

screws. The bird should be firmly in place on the rotisserie

spit rod.

ROTISSERIE CHART

Use a portable meat thermometer to check internal doneness of

the food.

Turn off rotisserie burner when meat thermometer reads 5°F/3°C

lower than desired internal temperature. Continue rotating, hood

closed, for 10 minutes before carving.

Timing is affected by weather conditions such as wind and

outside temperature.

Right-hand side flange

A. Lighting extension

B. Rotisserie burner

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

Food Weight Internal

Doneness or

Temperature

(°F/°C)

Approximate

Grilling Time

(min/lb)

Beef

Roasts

Rib Eye

Sirloin Tip

Rib, boneless

4-6 lbs

1.5-2.2 kg

Medium-rare

(145°F/ 63°C)

Medium

(160°F/71°C)

15-20

20-25

Poultry

Chicken

Turkey, whole

3-6 lbs

1.1-2.2 kg

7-10 lbs

2.6-3.7 kg

Breast

(170°F/ 77°C)

Thigh

(180°F/82°C)

Breast

(170°F/77°C)

Thigh

(180°F/82°C)

25-30

11-20

Using Your Smoker Box

(on some models and as an accessory)*

The smoker box can be used when grilling or when using your

rotisserie.

1. Prepare wood chips/pellets following manufacturer’s

directions.

2. Open smoker box lid and add prepared chips/pellets onto the

grate inside the smoker box.

NOTE: For about 1 hour of smoking, fill the smoker box

approximately one-fourth full of chips/pellets.

3. Remove the small grate from the grill and replace with the

smoker box.

4. Light the burner below the smoker box and preheat on high

until smoker begins smoking. Reduce the heat setting to

keep the smoke at the amount desired.

To Refill the Smoker Box During Use

IMPORTANT: You may want to wear oven mitts when opening

and closing the smoker box lid.

1. Open grill hood.

2. Lift smoker box lid and add more prepared chips/pellets.

3. Close the smoker box lid.

4. Close the grill hood and continue grilling.

*See “Assistance or Service” section to order.

Hood Lights

The 5,000 mAmp power transformer must be plugged in for the

hood lights to work. See “Plug in Grill” in the “Installation

Instructions” section.

To Use:

Press the LIGHTS button on the control panel to turn the hood

lights on and off.

TIPS FOR OUTDOOR

GRILLING

Before Grilling

■ Thaw food items before grilling.

■ Preheat grill on high (use all grill burners) 10 minutes. The

hood must be closed during preheating. There is no need to

use the back rotisserie burner for preheating. Preheating

provides the high heat needed to brown and seal the juices.

■ Shorten the preheat time when grilling high-fat cuts of meat

or poultry, such as chicken thighs. This will help reduce

flare-ups.

■ Lightly oil the grill grates or the food when cooking low-fat

cuts of meat, fish or poultry, such as lean hamburger patties,

shrimp or skinless chicken breasts.

■ Using too much oil can cause gray ash to deposit on food.

■ Trim excess fat from meats prior to cooking to reduce

flare-ups.

■ Make vertical cuts at 2" (5 cm) intervals around the fat edge

of meat to avoid curling.

■ Add seasoning or salt only after the cooking is finished.

During Grilling

■ Turn foods only once. Juices are lost when meat is turned

several times.

■ Turn meat just when juices begin to appear on the surface.

■ Avoid puncturing or cutting the meats to test doneness. This

allows juices to escape.

■ It may be necessary to lower the heat setting for foods that

cook a long time or are marinated or basted in a sugary

sauce.

■ If using a high flame, add barbecue sauce only during the last

10 minutes of cooking to avoid burning the sauce.

■ The degree of doneness is influenced by the type of meat, cut

of meat (size, shape and thickness), heat setting selected,

and length of time on the grill.

■ Cooking time will be longer with an open grill cover.

Lamb

Boneless leg 4-7 lbs

1.5-2.6 kg

Medium

(160°F/71°C)

20-25

Pork

Loin roast,

boneless

4-6 lbs

1.5-2.2 kg

Medium

(160°F/71°C)

20-23

A. Shown with small grate removed

B. Smoker box

Food Weight Internal

Doneness or

Temperature

(°F/°C)

Approximate

Grilling Time

(min/lb)

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

Cooking Methods

For optimal use of the SureSear™ system, the following cooking

methods are recommended.

Direct Heat

Cooking by direct heat means the food is placed on grill grates

directly above lighted burners. Hood position can be up or down.

If hood is in the up position, total cooking times may be longer.

Direct heat sears the food. Searing is a process that seals natural

juices in food by cooking with intense heat for a short period of

time. While juices stay inside, the outside is browned with a

flavorful grilled coating.

Indirect Heat

For best results, do not select the indirect heat cooking method

when it is windy.

Cooking by indirect heat means the food is placed on the grill

grate above an unheated burner, allowing heat from lighted

burner(s) on either side to cook the food.

If possible, turn on 2 burners. Cook with the hood down. This will

shorten the cooking time.

Indirect Cooking

Place food only on the grill grate over the OFF burners.

Grilling Chart

■ Knobs have High, Medium and Low settings for flame

adjustment.

■ Heat settings indicated are approximate.

■ Grilling times are affected by weather conditions.

■ When 2 temperatures are listed, for example: Medium to

Medium-Low, start with the first and adjust based on cooking

progress.

■ Cooking times may vary from chart times depending on the

type of fuel, Natural or LP gas.

Grill Size Burner Burner Burner Burner

1234

27" (68.6 cm) ON OFF - -

36" (91.4 cm) ON OFF ON -

48" (121.9 cm) ON OFF ON OFF

FOOD COOKING METHOD/

BURNER SETTING

INTERNAL TEMP. TIME

(total minutes)

SPECIAL INSTRUCTIONS

Beef

Hamburgers ½" (1.3 cm) to

¾" (1.9 cm) thick

Roasts

Rib Eye, Sirloin

Steaks, 1" (2.5 cm)

Porterhouse, Rib, T-bone,

Top Loin, Sirloin

Steaks, 1½" (3.8 cm)

Porterhouse, Rib, T-bone,

Top Loin, Sirloin

Top Round or Shoulder/

Chuck (London Broil)

1½" (3.8 cm) thick

Flank, ½" (1.3 cm) thick

DIRECT

Medium

INDIRECT

Medium/OFF/Medium

DIRECT

Medium

DIRECT

Medium

DIRECT

Medium

DIRECT

Medium

Medium (160°F/71°C)

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

Med-Rare (145°F/63°C)

to Medium (160°F/71°C)

Med-Rare (145°F/63°C)

10-15

32-40 per lb

(12-15 per kg)

11-16

18-25

22-29

11-16

Grill, turning once.

Tent with foil first 45-60 minutes

of cooking time.

Rotate steaks ¼ turn to create

criss-cross grill marks.

Pork

Chops,

1" (2.5 cm)

1½" (3.8 cm) thick

Ribs

2½-4 lbs (0.9-1.5 kg)

Roast, boneless tenderloin,

1 lb (0.37 kg)

Ham half,

8-10 lbs (3-3.7 kg)

Ham steak precooked,

½" (1.3 cm) thick

Hot Dogs

DIRECT

Medium to Med-Low

INDIRECT

Med/OFF/Med

DIRECT

Medium

INDIRECT

Med/OFF/Med

DIRECT

Preheat Medium

Grill Medium

DIRECT

Medium

Medium (160°F/71°C)

Reheat (140°F/60°C)

Reheat (145°F/63°C)

12-22

30-40

40-60

18-22

2-2½ hours

7-10

5-10

Grill, turning occasionally.

During last few minutes brush

with barbecue sauce if desired.

When done, wrap in foil.

Turn during cooking to brown

on all sides.

Wrap entire ham in foil and put

on grill without pan or drip pan.

Slit skin if desired.

La page charge ...

KitchenAid KBSS271TSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBSS271TSS0

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KBSS271TSS0 Owner's manual

KitchenAid KBSS271TSS0 Le manuel du propriétaire

KitchenAid KBSS271TSS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes