dewert okin RF427A Mode d'emploi

RF427A
Marque
dewert okin
Modèle
RF427A
Taper
Mode d'emploi
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 1 of 7
1 / 7
Instruction of RF427A
Figure 1 button ofremote
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 2 of 7
2 / 7
Item
1.1 Child Lock 1
Click the Child Lock button for 3 second to lock or unlock the remote.
1.2 Bed lamp 2
Click the bed lamp button to open or shut the light under the bed.
1.3 Antisnore 3
Click the Antisnore button, the bed moves to Antisnore position, press and hold Antisnore
button for 5s, until backlight flashes, the control set the current position as Antisnore position
1.4 TV 4
Click the TV button, the bed moves to TV position, press and hold TV button for 5s, until
backlight flashes, the control set the current position as TV position.
1.5 LUMBAR UP 5
Press and hold LUMBAR UP button, Lumbar actuator moves out, stop when released.
1.6 LUMBAR DOWN 6
Press and hold LUMBAR DOWN button, Lumbar actuator moves in, stop when released.
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 3 of 7
3 / 7
1.7 M1 7
Click the M1 button, the bed moves to M1 position, press and hold M1 button for 5s until
backlight flashes, the control set the current position as M1 position
1.8 M2 8
Click the M2 button, the bed moves to M2 position, press and hold M2 button for 5s until
backlight flashes, the control set the current position as M2 position
1.9 HEAD UP 9
Press and hold HEAD UP button, head actuator moves out, stop when released.
1.10 HEAD DOWN 10
Press and hold HEAD DOWN button, head actuator moves in, stop when released.
1.11 FOOT UP 11
Press and hold FOOT UP button,foot actuator moves out, stop when released.
1.12 FOOT DOWN 12
Press and hold FOOT DOWN button, foot actuator moves in, stop when released.
1.13 ZG 25
Click the ZG button, the bed moves to zeroG position, press and hold zeroG button for 5s,
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 4 of 7
4 / 7
until backlight flashes, the control set the current position as zeroG position
1.14 HEAD MASSAGE 14
Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.15 MASSAGE model 13
Click the MASSAGE MODEL button to change the massage model.
1.16 FOOT MASSAGE 15
Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3
1.17 FLAT 24
Click the FLAT button, the bed goes flat.
1.18 MASSAGE FREQUENT 28Hz 16
Click the 28Hz button to set the massage frequent 28Hz.
1.19 MASSAGE FREQUENT 40Hz 17
Click the 28Hz button to set the massage frequent 40Hz.
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 5 of 7
5 / 7
1.20 Left Fan without heat 18
Click the Left Fan without heat button, Left Fan switches intensity, Fan
intensityswitches among 0-1-2-3；
1.21 Left and right Fan without heat 19
Click the Left and right Fan without heat button, Left and right Fan switches intensity, Fan
intensityswitches among 0-1-2-3；
1.22 Right Fan without heat 20
Click the right Fan without heat button, right Fan switches intensity, Fan
intensityswitches among 0-1-2-3；
1.23 Left Fan with heat 21
Click the Left Fan with heat button, Left Fan switches intensity, Fan intensityswitches
among 0-1-2-3；
1.24 Left and right Fan with heat 22
Click the Left and right Fan with heat button, Left and right Fan switches intensity, Fan
intensityswitches among 0-1-2-3；
1.25 Right Fan with heat 23
Click the right Fan with heat button, right Fan switches intensity, Fan intensityswitches
among 0-1-2-3；
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 6 of 7
6 / 7
FCC Statement：
This device complies with part 15 of the FCC rules. Operation is subject to the following two cond
itions: (1) this device may not cause harmful interference, and (2) this device must accept any int
erference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could v
oid the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
tion against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructi
ons, may cause harmful interference to radio communications. However, there is no guarantee th
at interference will not occur in a particular installation. If this equipment does cause harmful int
erference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
- English: This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interferen
ce, and (2) This device must accept any interference, including interference that may cause u
ndesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradi
oélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.
Issue Department：Bedding
Division
Date：
2022-12-23
System Instruction
Author：
Instruction of RF427A
Edition：
1.0
Page 7 of 7
7 / 7
This radio transmitter (ISED certification number: 22406-RF408A) has been approved by
Industry Canada to operate with the antenna types listed with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (ISED certification number: 22406-RF408A) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un
gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

dewert okin RF427A Mode d'emploi

RF427A
Marque
dewert okin
Modèle
RF427A
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents