Pioneer GEX-P5750TV Mode d'emploi

Operation Manual

Hide-away TV tuner

GEX-P5750TV

English \-Español

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate

your model properly. After you have finished reading the instructions, keep this man-

ual in a safe place for future reference.

Precautions

IMPORTANT SAFEGUARDS 3

To ensure safe driving 3

To avoid battery exhaustion 4

Before You Start

About this unit 5

Video system of a connected component 5

About this manual 5

Resetting the microprocessor 5

Switching the operation mode 6

Use and care of the remote control 6



Installing the battery 6



Using the remote control 7

Whats What

Remote control 8

Other remote controls 8



When using a Pioneer car DVD

players remote control 8



When using a Pioneer car DVD

players remote control 9

TV tuner (SRC mode)

Whats What 10



Head unit (e.g., AVH-P5750DVD) 10

Operating with different head units 10

Function compatibility charts 11



Head unit group 1 11



Head unit group 2 11



Head unit group 3 11



Head unit group 4 11

Watching the television 12

Storing and recalling broadcast stations 13

Introduction of advanced TV tuner

operation 14

Storing the strongest broadcast stations

sequentially 14

TV tuner (STAND ALONE mode)

Watching the television 15

Storing the strongest broadcast stations

sequentially 15

Recalling broadcast stations 15

Confirming current channel and other

settings 16

Additional Information

Specifications 17

Contents

En

2

IMPORTANT SAFEGUARDS

Please read all of these instructions regarding

your display and retain them for future refer-

ence.

1 Read this manual fully and carefully be-

fore operating your display.

2 Keep this manual handy as a reference for

operating procedures and safety informa-

tion.

3 Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

4 Do not allow other persons to use this sys-

tem until they have read and understood

the operating instructions.

5 Do not install the display where it may (i)

obstruct the drivers vision, (ii) impair the

performance of any of the vehicles oper-

ating systems or safety features, includ-

ing air bags, hazard lamp buttons or (iii)

impair the drivers ability to safely oper-

ate the vehicle.

6 As with any accessory in your vehicles in-

terior, the display should not divert your

attention from the safe operation of your

vehicle. If you experience difficulty in op-

erating the system or reading the display,

please park safely before making adjust-

ments.

7 Please remember to wear your seat belt at

all times while operating your vehicle. If

you are ever in an accident, your injuries

can be considerably more severe if your

seat belt is not properly buckled.

8 Never use headphones while driving.

9 To promote safety, certain functions are

disabled unless the parking brake is on,

and the vehicle is not in motion.

10 Never set the volume of your display so

high that you cannot hear outside traffic

and emergency vehicles.

WARNING

! Do not attempt to install or service your

display by yourself. Installation or servi-

cing of the display by persons without

training and experience in electronic

equipment and automotive accessories

may be dangerous and could expose you

to the risk of electric shock or other

hazards.

To ensure safe driving

WARNING

! LIGHT GREEN LEAD AT POWER CON-

NECTOR IS DESIGNED TO DETECT

PARKED STATUS AND MUST BE CON-

NECTED TO THE POWER SUPPLY SIDE

OF THE PARKING BRAKE SWITCH. IM-

PROPER CONNECTION OR USE OF

THIS LEAD MAY VIOLATE APPLICABLE

LAW AND MAY RESULT IN SERIOUS IN-

JURY OR DAMAGE.

! To avoid the risk of accident and the potential

violation of applicable laws, the front TV fea-

ture should never be used while the vehicle is

being driven. Also, rear displays should not be

in a location where it is a visible distraction to

the driver.

! In some countries or states the viewing of

images on a display inside a vehicle even by

persons other than the driver may be illegal.

Where such regulations apply, they must be

obeyed and this units TV features should not

be used.

This unit detects whether your vehicles park-

ing brake is engaged or not, and prevents you

from watching TV on the front display while

driving. When you attempt to watch a TV, the

screen turns to black and nothing is dis-

played.

Precautions

En

3

English

Section

01

To watch TV on the front display, park your ve-

hicle in a safe place and apply the parking

brake.

To avoid battery exhaustion

Be sure to run the vehicle engine while using

this unit. Using this unit without running the

engine can result in battery drainage.

WARNING

Do not use with vehicles that do not feature an

ACC position.

Precautions

En

4

Section

01

About this unit

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, this unit damage, smoke, and overheat

could result from contact with liquids.

! Keep this manual handy as a reference for op-

erating procedures and precautions.

! Always keep the volume low enough so that

you can hear sounds from outside the vehicle.

! Protect this unit from moisture.

! If the battery is disconnected or discharged,

the preset memory will be erased and must be

reprogrammed.

! If this unit does not operate properly, contact

your dealer or nearest authorized Pioneer Ser-

vice Station.

This unit is a TV tuner for reception of TV

broadcasts. Combining it with a separately

sold display with AV-BUS lets you enjoy TV en-

tertainment (refer to this units installation

manual for details concerning the AV-BUS).

This unit features a REAR OUT, letting you

watch TV on a rear display (sold separately).

Video system of a

connected component

This unit is NTSC/PAL-M system compatible.

When connecting an external component to

this units REAR OUT, be sure the component

is compatible with the same video systems. If

it is not, images will not be correctly repro-

duced.

WARNING:

! Be sure to stop driving and park your vehicle

in a safe place before watching the TV.

! Watching the TV while driving is dangerous

and could result in an accident.

! This units REAR OUT is for connection of a

display to enable passengers in the rear seats

to watch the TV.

NEVER install the rear display in a location

that enables the driver to watch the TV while

driving.

About this manual

This unit features a number of sophisticated

functions ensuring superior reception and op-

eration. All the functions have been designed

for the easiest possible use, but many are not

self-explanatory. This operation manual will

help you benefit fully from this units potential

and to maximize your listening enjoyment.

We recommend that you familiarize yourself

with the functions and their operation by read-

ing through the manual before you begin

using this unit. It is especially important that

you read and observe WARNINGs and CAU-

TIONs in this manual.

Resetting the microprocessor

Pressing RESET lets you reset the micropro-

cessor to its initial settings.

The microprocessor must be reset under the

following conditions:

! Prior to using this unit for the first time

after installation

! If the unit fails to operate properly

! When strange or incorrect messages ap-

pear on the display

! When setting the position of the operation

mode switch on this unit

Before You Start

En

5

English

Section

02

% Press RESET with a pen tip or other

pointed instrument.

RESET button

Note

If you reset the microprocessor, memorized

broadcast stations and other information is

erased, and this unit returns to its initial

settings.

Switching the operation mode

This unit features three operation modes:

SRC : OSD OFF mode, SRC : OSD ON mode

and STAND ALONE mode. Switch the mode

according to the combined components.

SRC : OSD OFF mode

! Using with a Pioneer head unit featuring

an IP-BUS input.

! Not using this units OSD (On Screen Dis-

play) indications in the display.

SRC : OSD ON mode

! Using with a Pioneer head unit featuring

an IP-BUS input.

! Using this units OSD (On Screen Display)

indications in the display.

STAND ALONE mode

! Using with a display featuring RCA video

input.

% Use a thin standard tip screwdriver to

switch the operation mode switch.

! After switching, reset the micro-

processor.

Use and care of the remote

control

Installing the battery

Slide the tray out on the back of the remote

control and insert the battery with the plus (+)

and minus () poles pointing in the proper di-

rection.

WARNING

Keep the battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

CAUTION

! Use only one CR2025 (3 V) lithium battery.

! Remove the battery if the remote control is not

used for a month or longer.

! Do not recharge, disassemble, heat or dispose

of the battery in fire.

Before You Start

En

6

Section

02

! Do not handle the battery with metallic tools.

! Do not store the battery with metallic materi-

als.

! In the event of battery leakage, wipe the re-

mote control completely clean and install a

new battery.

! When disposing of used batteries, please

comply with governmental regulations or en-

vironmental public institutions rules that

apply in your country/area.

Using the remote control

Point the remote control in the direction of the

front panel to operate.

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Before You Start

En

7

English

Section

02

Remote control

This units supplied remote control is mainly

for use by rear seat passengers. When using,

point at the remote control sensor.

1 CH CALL button

SRC : OSD ON mode

When the TV is selected as a source, or,

when the rear TV is on and the TV is not se-

lected as a source:

Channel information is displayed on the

front and rear display.

SRC : OSD OFF mode

When the TV is selected as a source, or,

when the rear TV is on and the TV is not se-

lected as a source:

Channel information is displayed on the

rear display.

STAND ALONE mode

Press to display the current channel and

other settings (Confirming current channel

and other settings on page 16).

2 BAND button

SRC : OSD ON mode

Not used. Alternatively, use BAND on the

head unit.

SRC : OSD OFF mode

Not used. Alternatively, use BAND on the

head unit.

STAND ALONE mode

Press to select among two TV bands and to

cancel the control mode of functions.

3 MENU button

Not used.

4 a/b/c/d buttons

SRC : OSD ON mode

Press to do manual seek tuning and preset

tuning. Also used for controlling functions.

SRC : OSD OFF mode

Press to do manual seek tuning and preset

tuning. Also used for controlling functions.

STAND ALONE mode

Press to do manual seek tuning and preset

tuning.

5 POWER button

SRC : OSD ON mode

Press to turn the rear display on or off when

the TV is not selected as a source.

SRC : OSD OFF mode

Press to turn the rear display on or off when

the TV is not selected as a source.

STAND ALONE mode

Press to turn this unit on or off.

Other remote controls

You can also perform operations with the re-

mote controls shown below.

When using a Pioneer car DVD

players remote control

When using a remote control supplied with

SDV-P7, AVX-P7300DVD, XDV-P9, XDV-P9

II

.

1 r button

Press and hold to BSSM on or off.

2

5

3

1

4

Whats What

En

8

Section

03

2 Remote control operation mode switch

When operating a TV, be sure to set the re-

mote control operation mode switch to TV

position.

When using a Pioneer car DVD

players remote control

When using a remote control supplied with

AVH-P7650DVD, AVH-P7550DVD, AVH-

P6650DVD, AVH-P6550DVD, AVH-P5750DVD,

AVX-P7650DVD.

1 16 buttons

Press to do direct channel select.

2 Joystick

Move to do manual seek tuning and preset

tuning. When using this unit as

STAND ALONE mode, click to display the

area group setting screen. Also used for

controlling functions.

3 Remote control operation mode switch

When operating a TV, be sure to set the re-

mote control operation mode switch to TV

position.

Whats What

En

9

English

Section

03

Only when using this unit with SRC mode,

you can perform the following operations

by head unit.

Whats What

Head unit (e.g., AVH-P5750DVD)

Operate this unit (for TV reception) with the

connected head unit. Instructions in this man-

ual use AVH-P5750DVD as an example of

head unit.

1 VOLUME

Press to increase or decrease the volume.

2 Signal receptor

Receives signals from a remote control.

3 SOURCE button

This unit is turned on by selecting a source.

Press to cycle through all the available

sources.

4 BAND button

Press to select among two TV bands and to

cancel the control mode of functions.

5 A.MENU button

Press to display MENU.

6 a/b/c/d buttons

Press to do manual seek tuning. Also used

for controlling functions.

Operating with different

head units

Head unit group 1

The following head units featuring touch

panel key operation.

AVH-P7650DVD, AVH-P7550DVD, AVH-

P6650DVD, AVH-P6550DVD, AVH-P5750DVD

5

4

3

6

1

2

TV tuner (SRC mode)

En

10

Section

04

Head unit group 2

When using the following head units, opera-

tion is different from AVH-P5750DVD.

The following head units featuring FUNCTION

button operation or SOFT KEY operation.

KEH-P7035, FH-P9200MP, FH-P6200, FH-

P5000MP, FH-P4200MP, DVH-P5650MP, DVH-

P5050MP, DEH-P9650MP, DEH-P7650MP, DEH-

P7550MP, DEH-P6750MP, DEH-P6550, DEH-

P5750MP, DEH-P5650MP, DEH-P5550MP, DEH-

P4750MP, DEH-P4650MP, DEH-P4550, DEH-

P3550MP, DEH-P2650MP, DEH-P2550

Head unit group 3

When using the following head units, opera-

tion is different from AVH-P5750DVD.

The following head units featuring

MULTI-CONTROL operation.

DEH-P8650MP, DEH-P7750MP, DEH-P1Y

Head unit group 4

When using the following head units, opera-

tion is different from AVH-P5750DVD.

The following head units featuring remote con-

trol operation.

AVX-P7650DVD

Function compatibility charts

Head unit group 1

Controls

Select TV as a source Press SOURCE.

Select a band Touch BAND.

Preset tuning Touch a or b.

Manual tuning (step

by step)

Tou ch c or d.

Seek tuning Keep touching c or d.

Select a function

Tou ch A.MENU and then

touch FUNCTION.

Head unit group 2

Controls

Select TV as a source Press SOURCE.

Select a band Press BAND.

Preset tuning Press a or b.

Manual tuning (step

by step)

Press c or d.

Seek tuning Press and hold c or d.

Preset memory Press and hold 16.

Direct recall Press 16.

BSSM

Press FUNCTION (FUNC)

(A.MENU).

a/b

Preset channel list

Press FUNCTION (FUNC)

(A.MENU).

a/b/c/d

Head unit group 3

Controls

Select TV as a source Press SOURCE.

Select a band Press BAND.

Preset tuning

Push MULTI-CONTROL up

or down.

Manual tuning (step

by step)

Push MULTI-CONTROL left

or right.

Seek tuning

Push and hold MULTI-CON-

TROL left or right.

Select a function Use MULTI-CONTROL.

Head unit group 4

Controls

Select TV as a source Press SOURCE.

Select a band Press BAND.

Preset tuning

Move the joystick up or

down.

TV tuner (SRC mode)

En

11

English

Section

04

Controls

Manual tuning (step

by step)

Move the joystick left or

right.

Seek tuning

Hold the joystick left or right

for about one second and re-

lease.

Select a function Use the joystick.

Watching the television

1

3

4

2

5

1 Source icon

Shows which source has been selected.

2 Band indicator

Shows which band the TV tuner is tuned to.

3 Preset number indicator

Shows which preset has been selected.

4 Channel indicator

Shows which channel the TV tuner is tuned.

5 Preset list display

Shows the preset list.

1 Touch the screen to display the touch

panel keys.

2 Touch BAND to select a band.

Touch BAND repeatedly until the desired band

is displayed, TV1 or TV2.

3 To select a preset channel, touch a pre-

set channel on the list.

The preset channel you selected is tuned in.

# When the list of channels is not displayed,

touch LIST.

TV tuner (SRC mode)

En

12

Section

04

4 To perform manual tuning, briefly

touch c or d.

The channels move up or down step by step.

# You can also perform manual tuning by press-

ing c or d button.

5 To perform seek tuning, keep touching

c or d for about one second and release.

The tuner will scan the channels until a broad-

cast strong enough for good reception is

found.

# You can cancel seek tuning by briefly touching

either c or d.

# If you keep touching c or d you can skip

broadcasting channels. Seek tuning starts as

soon as you release the keys.

# You can also perform seek tuning by pressing

and holding c or d button.

Storing and recalling

broadcast stations

If you touch any of the preset tuning keys

P1P12 you can easily store up to 12 broad-

cast stations for later recall with the touch of a

key.

% When you find a station that you want

to store in memory, keep touching one of

preset tuning keys P1P12 until the preset

number stops flashing.

The number you have touched will flash in the

preset number indicator and then remain lit.

The selected station has been stored in mem-

ory.

The next time you touch the same preset tun-

ing key the station is recalled from memory.

# To switch between P1P6 and P7P12, touch

or .

# When the touch panel keys are not displayed,

you can display them by touching the screen.

# When P1P6 and P7P12 are not displayed,

you can display them by touching LIST.

Notes

! Up to 24 stations, 12 for each of two TV bands,

can be stored in memory.

! You can also use a and b to recall stations

assigned to preset tuning keys P1P12.

TV tuner (SRC mode)

En

13

English

Section

04

Introduction of advanced

TV tuner operation

1

1 Function display

Shows the function name.

1 Press A.MENU button to display MENU.

MENU appears on the display.

2 Touch FUNCTION to display the func-

tion name.

The function name is displayed.

# To return to the previous display, touch BACK.

# To return to the TV picture, touch ESC.

Note

If you do not operate the function within about 30

seconds, the display is automatically returned to

the TV picture.

Storing the strongest

broadcast stations

sequentially

% Touch BSSM on the function menu to

turn BSSM on.

BSSM begins to flash. While BSSM is flashing

the 12 strongest broadcast stations will be

stored in order from the lowest channel up.

When finished, BSSM disappears.

# To cancel the storage process, touch BSSM

again.

# You can also perform this operation by press-

ing and holding CH CALL on the remote control.

Note

Storing broadcast stations with BSSM may re-

place broadcast stations you have saved using

P1P12.

TV tuner (SRC mode)

En

14

Section

04

Watching the television

3

1

2

Only when using this unit with

STAND ALONE mode, you can perform the

following operations by this unit.

Only the remote control can operate the fol-

lowing functions.

1 Channel indicator

Shows which channel the TV tuner is tuned.

2 Preset number indicator

Shows which preset has been selected.

3 Band indicator

Shows which band the TV tuner is tuned to.

1 Press POWER to turn the TV on.

2 Press BAND to select a band.

3 To perform manual tuning, briefly press

c or d.

The channels move up or down step by step.

# You can also perform manual tuning by press-

ing CHANNEL.

4 To perform seek tuning, press and hold

c or d for about one second and release.

The tuner will scan the channels until a broad-

cast strong enough for good reception is

found.

# You can cancel seek tuning by briefly pressing

either c or d.

# If you press and hold c or d you can skip

broadcasting channels. Seek tuning starts as

soon as you release the button.

Storing the strongest

broadcast stations

sequentially

BSSM (best stations sequential memory) lets

you automatically store the 12 strongest

broadcast stations in order from the lowest

channel up.

% Press CH CALL and hold to turn BSSM

on.

BSSM begins to flash. While BSSM is flashing

the 12 strongest broadcast stations will be

stored in order from the lowest channel up.

When finished, BSSM disappears.

# To cancel the storage process, press and hold

CH CALL again.

Recalling broadcast stations

You can easily recall preset channels P1P12

stored by BSSM.

% Press a or b to recall preset channels

P1P12.

TV tuner (STAND ALONE

mode)

En

15

English

Section

05

Confirming current channel

and other settings

You can display the reception information

such as the channel, band and preset channel

list.

! Only the remote control can operate this

function.

% Press CH CALL to display the reception

information.

Each press of CH CALL displays reception in-

formations in the following order:

Current channel information (channel and

band)Preset channel listReception infor-

mations disappear

# Reception informations are displayed for eight

seconds.

TV tuner (STAND ALONE

mode)

En

16

Section

05

Specifications

General

Rated power source ............... 14.4 V DC

(allowable voltage range:

12.0  14.4 V DC)

Grounding system ................... Negative type

Max. current consumption

..................................................... 0.6 A

Dimensions (W × H × D) ... 172 × 30 × 150 mm

Weight .......................................... 0.7 kg

TV tuner

Reception channel .................. VHF 2  13 ch, UHF 14  69

ch

Color system .............................. NTSC/PAL-M compatible

Usable sensitivity ..................... 11 dBµ (75 W, Mono)

Video S/N ..................................... Over 40 dB (59 dBµ RF

input, White Peak 100%)

Video S/N 30 dB usable sensitivity

..................................................... 44 dBµ

Antenna input ........................... 4 ch Diversity (ø 3.5 mm

Mini plug type)

Rear display output

Video .............................................. 1 Vp-p/75W (TV: White 100%

Modulated)

Sound ............................................ 500 mVrms/Less than 1kW

(TV: 100% Modulated)

Infrared remote control

Wavelength ................................. 945 nm

Output ........................................... typ; 12 mw/sr per Infrared

LED

Note

Specifications and the design are subject to pos-

sible modifications without notice due to im-

provements.

Additional Information

En

17

English

Appendix

Gracias por haber comprado este producto Pioneer.

Lea con detenimiento estas instrucciones sobre el funcionamiento del aparato,

para que pueda dar el mejor uso posible a su modelo. Una vez que las haya leído,

guarde este manual en un lugar seguro para consultarlo en el futuro.

Precauciones

INSTRUCCIONES DE SEGURIDAD

IMPORTANTES 19

Para garantizar la conducción segura del

vehículo 19

Para evitar la descarga de la batería 20

Antes de comenzar

Acerca de esta unidad 21

Sistema de vídeo de un componente

conectado 21

Acerca de este manual 21

Reinicialización del microprocesador 22

Cambio del modo de funcionamiento 22

Uso y cuidado del mando a distancia 23



Instalación de la batería 23



Uso del mando a distancia 23

Qué es cada cosa

Mando a distancia 24

Otros mandos a distancia 25



Al usar el mando a distancia de un

reproductor Pioneer de DVD para

automóvil 25



Al usar el mando a distancia de un

reproductor Pioneer de DVD para

automóvil 25

Sintonizador de TV (modo SRC)

Qué es cada cosa 26



Unidad principal (p. ej., AVH-

P5750DVD) 26

Funcionamiento con diferentes unidades

principales 27

Tablas de compatibilidad de funciones 27



Grupo 1 de unidades principales 27



Grupo 2 de unidades principales 27



Grupo 3 de unidades principales 28



Grupo 4 de unidades principales 28

Uso del televisor 28

Almacenamiento y llamada de emisoras 29

Introducción a las funciones avanzadas del

sintonizador de TV 30

Almacenamiento consecutivo de las

emisoras con señales más fuertes 30

Sintonizador de TV (modo STAND

ALONE)

Uso del televisor 31

Almacenamiento consecutivo de las

emisoras con señales más fuertes 31

Llamada de emisoras 31

Confirmación del canal actual y otros

ajustes 32

Información adicional

Especificaciones 33

Contenido

Es

18

INSTRUCCIONES DE

SEGURIDAD IMPORTANTES

Lea todas estas instrucciones sobre el display

y consérvelas para consultarlas en el futuro.

1 Lea todo este manual con suma atención

antes de utilizar el display.

2 Conserve este manual a mano para que

pueda consultar los procedimientos de

operación y la información sobre seguri-

dad cuando sea necesario.

3 Preste mucha atención a todas las adver-

tencias que se indican en este manual y

siga las instrucciones con cuidado.

4 No permita que otras personas utilicen

este sistema hasta que hayan leído y com-

prendido las instrucciones sobre el funcio-

namiento del aparato.

5 No instale el display en un lugar que (i)

pueda obstaculizar la visión del conduc-

tor, (ii) pueda alterar el funcionamiento de

los sistemas operativos o los dispositivos

de seguridad del vehículo, en particular

las airbags y los botones de luces de se-

guridad o (iii) pueda afectar la capacidad

del conductor para manejar el vehículo de

manera segura.

6 Al igual que con cualquier accesorio ubi-

cado en el interior del vehículo, el display

no debe desviar su atención del manejo

seguro del vehículo. Si tiene dificultades

para utilizar el sistema o leer el display,

estacione en un lugar seguro antes de

hacer algún ajuste.

7 Recuerde usar siempre el cinturón de se-

guridad cuando conduzca el vehículo. En

caso de accidente, las lesiones pueden ser

mucho más graves si el cinturón de segu-

ridad no está debidamente abrochado.

8 Nunca use auriculares mientras conduce.

9 Para promover la seguridad, ciertas fun-

ciones están desactivadas a menos que se

active el freno de mano y el vehículo no

esté en movimiento.

10 Nunca fije el volumen del display tan alto

que no pueda escuchar el tráfico exterior

y los vehículos de emergencia.

ADVERTENCIA

! No trate de instalar o reparar el display

usted mismo. La instalación o la repara-

ción del display por parte de personas sin

capacitación y experiencia en equipos

electrónicos y accesorios para automóvi-

les puede ser peligrosa y puede exponerlo

al riesgo de sufrir una descarga eléctrica o

a otros peligros.

Para garantizar la conducción

segura del vehículo

ADVERTENCIA

! EL CABLE VERDE CLARO DEL CONEC-

TOR DE ALIMENTACIÓN ESTÁ DISEÑA-

DO PARA DETECTAR SI EL VEHÍCULO

ESTÁ ESTACIONADO Y DEBE CONEC-

TARSE CON EL LADO DE LA FUENTE DE

ALIMENTACIÓN DEL INTERRUPTOR

DEL FRENO DE MANO. LA CONEXIÓN O

EL USO INCORRECTO DE ESTE CABLE

PUEDE INFRINGIR LAS LEYES PERTI-

NENTES Y OCASIONAR LESIONES FÍSI-

CAS O DAÑOS GRAVES.

! Para evitar el riesgo de accidentes y la posible

violación de las leyes pertinentes, la función

de TV delantera nunca debe utilizarse mien-

tras se maneja el vehículo. Además, los dis-

plays traseros no deben estar en un lugar

donde sean una distracción visual para el

conductor.

Precauciones

Es

19

Sección

Español

01

! En algunos países o estados, puede ser ilícita

la visualización de imágenes en un display

dentro de un vehículo, incluso por otras perso-

nas que no sean el conductor. En los casos en

que resulten aplicables, estas normas deben

respetarse y no deben usarse las funciones de

TV de esta unidad.

Esta unidad detecta si el freno de mano del

automóvil está activado o no, y le impide ver

programas de TV en el display delantero mien-

tras conduce. Si intenta ver un programa de

TV, la pantalla de ennegrecerá y no se mostra-

rá nada en ella.

Para ver un programa de TV en el display de-

lantero, estacione el automóvil en un lugar se-

guro y active el freno de mano.

Para evitar la descarga de

la batería

Utilice esta unidad con el motor del vehículo

encendido. De no hacerlo, se puede descargar

la batería.

ADVERTENCIA

No utilice la unidad con un vehículo que no cuen-

te con la posición ACC.

Precauciones

Es

20

Sección

01

La page charge ...

Pioneer GEX-P5750TV Mode d'emploi

Pioneer GEX-P5750TV Mode d'emploi

dans d''autres langues

Documents connexes