Maruyama BH24 Le manuel du propriétaire

Équipement pour utilisation à l’extérieur de qualité supérieure

Lisez attentivement l’intégralité du présent manuel avant d’utiliser ce p r oduit.

E xtraordi nai r e .

BH24BH24S

HEDGE TRIMMER

TAILLE-HAIE

CORTASETOS

Equipo d e c ali dad sup eri or p ara u so e n e xteri o r e s

Antes de utilizar este pr oducto, lea atentamente este manual.

E xtraordinario.

OWNER'S/OPERATOR'S MANUAL

MANUEL DU PROPRIETAIRE/DE LU'TILISATEUR

MANUAL DEL PROPIETARIO U OPERADOR

English

｜  ｜

Limited Warranty Statement

All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from defects

in material and workmanship from the date of purchase for the time periods listed as follows:

Lifetime for inner drive shaft on trimmers and brushcutters and all ignition modules.

3 years for residential, non-institutional, non-income producing use.

1 year for industrial, commercial, institutional, rental and income producing use.

Maruyama AE series engines and Kawasaki TEX45/TEX54 are covered exclusively for one additional

year of industrial, commercial, institutional, rental and income producing use (total of 2 years).

All other engines refer to engine manufacturer's warranty statement.

Any part of a Maruyama product found to be defective within the applicable warranty period shall, at

Maruyama's option, be repaired or replaced without charge. Warranty consideration is obtained by deliver-

ing any Maruyama product believed to be defective to an Authorized Maruyama Servicing Dealer within the

applicable warranty period.

The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted part

is defective, if the diagnostic work is performed at a Maruyama Dealer.

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled

only for regular inspection to the effect of "repair or replace as necessary" shall be warranted for the warranty

period. Any warranted part, which is scheduled for replacement as, required maintenance shall be warranted

for the period of time up to the first scheduled replacement point for that part. Maruyama Mfg. Co., Inc. is lia-

ble for damages to other engine components caused by the failure of a warranted part still under warranty.

The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama

Mfg. Co., Inc. in the Owner's/Operator's Manual.

EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama Mfg.

Co., Inc. will repair or replace, free of charge, for the original purchaser and each subsequent purchaser any

emission-related part or parts found to be defective in material and workmanship for two (2) years from origi-

nal retail delivery date except catalytic converter. Catalytic converter is warranted one year from origi-

nal retail delivery date. Emission-related parts are the carburetor assembly, the ignition coil

assembly, the ignition rotor and the spark plug and catalytic converter. Any replacement part that is

equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not

reduce the warranty obligations of Maruyama Mfg. Co., Inc.

Effective June 1, 2000

English

｜  ｜

This warranty does not cover the following:

1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs,

starter rope, air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting attach-

ments, etc.

2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any inconve-

nience and storage.

3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.

4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when appli-

cable), or failure to operate or maintain the product in accordance with instructions approved by

Maruyama.

Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Maruyama

shall not be liable for any incidental or consequential damages for breach of any express or implied warranty

on these products except to the extent prohibited by applicable law. Any implied warranty of merchantability

or fitness for a particular purpose on these products is limited in duration to the warranty period as defined in

the limited warranty statement. Maruyama reserves the rights to change or improve the design of the prod-

uct without notice and does not assume obligation to update previously manufactured products.

This warranty provides you with specific legal rights, which may vary from state to state.

It is the Owner's and Dealer's responsibility to make sure the Warranty Registration Card is properly filled out

and mailed to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to obtain war-

ranty service.

To locate an Authorized Maruyama Servicing Dealer nearest you, contact:

.

Maruyama U.S., Inc.

4770 Mercantile Drive, suite 100,

Fort Worth, TX 76137

(940) 383-7400

maruyama@maruyama-us.com

www.maruyama-us.com

Effective June 1, 2000

English

｜  ｜

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA)

and Maruyama Manufacturing Company, Inc.

are pleased to explain the

emission control system warranty

on your small off-road engine. New

1997 and later model year small off-road engines must be designed, built and equipped, at the

time of sale, to meet the U.S. EPA regulations for small off-road engines. The equipment engine

must be free from defects in materials and workmanship which cause it to fail to conform with U.S.

EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser.

Maruyama Manufacturing Company, Inc. must warrant the emission control system on your small

off-road engine for the period of time listed above provided there has been no abuse, neglect or

improper maintenance of your small off-road engine.

Emission durability of 300 hours.

Your emission control system may include parts such as the carburetor or fuel injection system,

the ignition system, and catalytic converter. Also included may be hoses, belts, and connectors

and other emission related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your

small off-road engine at no cost to you, including diagnosis (if the diagnostic work is performed

at an authorized dealer), parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1997 and later model year small off-road engines are warranted for two years. If any

emission-related part on your engine is defective, the part will be repaired or replaced by

Maruyama Manufacturing Company, Inc. free of charge.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

:

2

0

4

6

8

10

THE AIR INDEX OF THIS ENGINE IS 3

MOST CLEAN

NOTE:THE LOWER THE AIR INDEX, THE LESS POLLUTION

THIS ENGINE IS CERTIFIED TO BE EMISSIONS

COMPLIANT FOR THE USE:EXTENDED: 300HOURS

CHECK THE OWNER'S MANUAL FOR FURTHER DETAILS

For more information,

Visit us on the web at

www.maruyama-us.com

LEAST CLEAN

.

CER230HT

English

｜  ｜

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required

maintenance listed in your owner's manual.

Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering

maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.

cannot deny warranty solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance. Any replacement part or service that is

equivalent in performance and durability may be used in non-warranty maintenance or

repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b) As the small off-road engine owner, you should be aware, however, that Maruyama

Manufacturing Company may deny you warranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

(c) You are responsible for presenting your small off-road engine to a Maruyama Manufacturing

Company, Inc. service center as soon as a problem exists. The warranty repairs should be

completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should

contact Maruyama U.S., Inc. at 1-866-783-7400, or [email protected].

COVERAGE

Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each

subsequent purchaser that your small off-road engine will be designed, built and equipped, at

the time of sale, to meet all applicable regulations. Maruyama Manufacturing Company, Inc.

also warrants to the initial purchaser and each subsequent purchaser that your small off-road

engine is free from defects in materials and workmanship which cause the engine to fail to

conform with applicable regulations for a period of two years.

The 1997 and later model years, EPA requires manufacturers to small off-road engines for two

years. These warranty periods will begin on the date the small off-road engine is purchased by

the initial purchaser. If any emission-related part on your engine is defective, the part will be

replaced by Maruyama Manufacturing Company, Inc. at no cost to the owner.

Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized

Maruyama Manufacturing Company, Inc. engine dealer or warranty station. Any authorized

work done at an authorized dealer or warranty station shall be free of charge to the owner if

such work determines that a warranted part is defective. Any manufacturer-approved or

equivalent replacement part may be used for any warranty maintenance or repairs on emission-

related parts, and must be provided free of charge to the owner if the part is still under warranty,

Maruyama Manufacturing Company, Inc. is liable for damages to other engine components

caused by the failure of a warranted part still under warranty.

English

｜  ｜

EPA considers emission-related warranted parts to include all the parts listed below. These

warranted parts are:

the carburetor assembly, the ignition coil assembly, the ignition

rotor, the spark plug, the catalytic converter, and the fuel tank.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by the

Maruyama Manufacturing Company, Inc. in the owner's manual.

LIMITATIONS

This Emission Control System Warranty shall not cover any of the following:

(a) repair or replacement required because of misuse or neglect, lack of required maintenance,

repairs improperly performed or replacements not conforming to Maruyama Manufacturing

Company, Inc. specifications that adversely affect performance and/or durability, and

alterations or modifications not recommended or approved in writing by Maruyama

Manufacturing Company, Inc., and

(b) replacement of parts and other services and adjustments necessary for required

maintenance at and after the first scheduled replacement point.

English

｜  ｜

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board (CARB), and Maruyama Manufacturing Company, Inc. are

pleased to explain the emission control system warranty on your 2015 small off-road engine. In

California, new small off-road engines must be designed, built and equipped to meet the State's

stringent anti-smog standards. Maruyama Manufacturing Company, Inc. must warrant the emission

control system on your small off-road engine for the period of time listed above provided there has

been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the

ignition system, fuel tank and catalytic converter. Also included may be hoses, belts, and

connectors and other emission related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your

small off-road engine at no cost to you, including diagnosis, parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years. If any emission-related

part on your engine is defective, the part will be repaired or replaced by Maruyama

Manufacturing Company, Inc.

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required

maintenance listed in your owner's manual.

Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering

maintenance on your small off-road engine, but Maruyama Manufacturing Company, Inc.

cannot deny warranty solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance

(b) As the small off-road engine owner, you should be aware, however, that Maruyama

Manufacturing Company may deny you warranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

(c) You are responsible for presenting your small off-road engine to a Maruyama Manufacturing

Company, Inc. distribution center as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days.

English

｜  ｜

If you have any questions regarding your warranty rights and responsibilities, you should

contact Maruyama U.S., Inc. at 1-866-783-7400, or [email protected].

Emission System Parts

Exhaust Emission

Carburetor

Muffler

Catalytic Converter

Ignition Coil / Magneto

Spark Plug

Air Filter

EGR Valve (piston)

Fuel Filter

Evaporative Emission

Fuel Tank

English

｜  ｜

FOREWORD

This Ownerʼs/Operatorʼs Manual is designed to familiarize the operator with the various features

and component parts of the equipment and to assist you with the operation and maintenance of

your new Hedge Trimmer.

It is essential that any operator of this Hedge Trimmer product reads and understands the

contents of this manual before using the Hedge Trimmer.

Important safety instructions will be identified by the following safety symbol:

Failure to comply with the instructions in this manual may result in serious injury or death.

For additional assistance, contact any local authorized MARUYAMA dealer or Maruyama U.S., Inc.,

4770 Mercantile Drive, suite100, Fort Worth, TX 76137

TABLE OF CONTENTS

SPECIFICATIONS

Model

BH24 BH24S

Dimensions L x W x H

1035 × 245 × 220 mm

(40.5 × 9.6 × 8.7in)

1040 × 255 × 235 mm

(40.9 × 10.0 × 9.2in)

Dry Weight 5.7kg(12.5lbs.) 5.9kg(13.0lbs.)

Blade Length 600mm(24in) 750mm(30in)

Rear Handle

Fixed

Engine Model CER230HT

Engine Displacement

22.5 cm

3

Fuel Tank Capacity

0.5(0.53 qts.)

Carburetor Walbro Diaphragm Type

Ignition System Solid State

Spark Plug:

Make

Type

Electrode Gap

NGK

BPM8Y

0.6

〜

0.7 mm (0.024

〜

0.028 in.)

Fuel Mixture:

50:1

Using MARUYAMA 50:1 Two-Stroke Engine Oil or any Quality two-stroke engine

oil designed for use in air-cooled, high performance two-stroke engines.

Warranty

 

1

Foreword

 

8

Specications

 

8

Product description



9

Warning



10

Before operation

 

13

Starting and stopping procedure

 

16

Carburetor adjustment



17

Operating the Power Hedge Trimmer

 

18

Regular maintenance

 

18

Storage

 

21

Maintenance Period



22

English

｜  ｜

PRODUCT DESCRIPTION

MODELS : BH24



















MODELS : BH24S























English

｜  ｜

WARNING

Operator safety

1. Read and understand this Ownerʼs/Operatorʼs Manual before using this product. Be thoroughly

familiar with the proper use of this product.

2. Always wear eye protection that complies with ANSI (American National Standards Institute)

Z87-1.

3. Wear hearing protection.

4. Always wear heavy long pants, boots and gloves. Do not wear

loose clothing, jewelry, short pants, sandals or go barefoot.

Secure hair so it is above shoulder length.

5. Never operate this Hedge Trimmer when you are tired, ill, under

the influence of alcohol, drugs or medication.

6. Never start or run the engine inside a closed room or building.

Breathing exhaust fumes can cause death.

7. Keep handle clean of oil, fuel and dirt.

English

｜  ｜

Power Hedge Trimmer safety

1. Shut off the engine and wait unit the cutting blades have completely stopped moving before

checking, maintaining or working on the Hedge Trimmer.

2. Inspect the Hedge Trimmer before each use. Replace damaged parts. Check for fuel leaks.

Make sure all fasteners are in place and tightened securely.

3. Inspect the Hedge Trimmer cutting blades and guide. Replace any parts that are cracked,

chipped, or damaged before using the Hedge Trimmer.

4. Never use replacement parts that are not approved by Maruyama U.S., Inc.

5 Maintain the Hedge Trimmer in accordance with the recommended maintenance intervals and

procedures in the maintenance section, pages 18 to 21.

6. If running problems or excessive vibration occur, stop immediately and inspect the unit for the

cause. If the cause cannot be determined or is beyond your ability to correct, return the Hedge

Trimmer to your servicing dealer for repair.

7. Never use the Hedge Trimmer if handles are damaged or handle fasteners are loose.

Always make sure all fasteners (nuts and bolts) are installed and properly tightened.

8. Never use a machine that has been modified so that it no longer corresponds with the original

design.

9. Do not attempt to repair the Hedge Trimmer unless you are qualified to do so.

10. When transporting or storing the Hedge Trimmer always install the blade shield.

Fuel safety

1. Gasoline is highly flammable and must be handled and stored

carefully. Use a container approved for storing gasoline and/or

fuel/oil mixture.

2. Mix and pour fuel outdoors and where there are no sparks or

flames.

3. Do not smoke near fuel or the Hedge Trimmer or while using the

Hedge Trimmer.

4. Do not overfill the fuel tank. Stop filling 1/4 - 1/2 inch (6mm-13mm)

from the top of the tank.

5. Wipe up any spilled fuel before starting the engine.



English

｜  ｜

6. Move the Hedge Trimmer at least 10 feet (3 m) away

from the fueling location before starting the engine.

7. Do not remove the Hedge Trimmer fuel tank cap while

the engine is running or immediately after stopping the

engine.

8. Allow the engine to cool before refueling.

9. Empty the fuel tank before storing the Hedge Trimmer.

Fuel should be emptied after each use. Fuel left in the

tank may leak during storage.

10. Store fuel and Hedge Trimmer away from open

flame, sparks and excessive heat. Make sure fuel

vapors cannot reach sparks or open flames from water

heaters, furnaces, electric motors, etc.

Power Hedge Trimmer operating safety

1. THIS HEDGE TRIMMER CAN CAUSE SERIOUS INJURIES.

Read the instructions carefully. Be familiar with all controls and the proper use of the Hedge

Trimmer.

2. Never allow children to operate the Hedge Trimmer. It is not a toy.

3. Keep the area of operation clear of all persons, particularly small children and pets.

4. The Hedge Trimmer blades are extremely sharp. Do not put hands or feet near or under any

moving parts. Keep body clear at all times.

5. Use the Hedge Trimmer only in daylight or good artificial light.

6. Inspect your work area before you begin. Remove string, rope or similar materials which can

become entangled in the Hedge Trimmer blades.

7. Avoid hidden hazards. Watch for hidden objects within your working area, such as chain link

fencing, cables, wires, telephone and power lines.

8. Never operate the Hedge Trimmer without proper guards or other protective safety devices in

place.

9. Keep a firm footing and balance. Do not over-reach. Do not operate the Hedge Trimmer while

standing on a ladder or similar temporary support.

10. Use the right tool for the job. Do not use the Hedge Trimmer for any job that is not

recommended by the manufacturer.





English

｜  ｜

11. While operating the Hedge Trimmer be always sure of a safe and secure operating position.

Do not over reach.

12. To reduce fire hazard keep engine and muffler free of debris, leaves, and dry materials.

Always wipe away spilled fuel and excessive lubricant before starting.

13. Always use two hands to operate the Hedge Trimmer.

14. Always be aware of your surroundings and stay alert for possible hazards that you may not

hear due to the noise of the machine.

15. Know how to stop the machine quickly in emergency. (See to stop the engine in STARTING

AND STOPPING PROCEDURE SECTION.)

BEFORE OPERATION

FUELING

WARNING!

The following precautions will lessen the risk of fire.

1. Do not smoke near fuel.

2. Mix and pour fuel outdoors and where there are no sparks or flames.

3. Always shut off the engine before refueling. Never remove the Hedge Trimmer fuel tank cap

while the engine is running or immediately after stopping the engine.

4. Always open the fuel tank cap slowly to release any possible pressure inside the tank.

5. Do not overfill the fuel tank. Stop filling 1/4

-

1/2 inch

(6mm-13mm) from the top of the tank.

6. Tighten the tank fuel cap carefully but firmly after refilling.

7. Wipe up any spilled fuel before starting the engine.

8. Move the Hedge Trimmer at least 10 feet (3m) away from the

fueling location and fuel storage container before starting the

engine.





English

｜  ｜

FUEL; MIXING GASOLINE AND OIL

IMPORTANT

The engine used on this Hedge Trimmer is of a two-stroke design. The internal

moving parts of the engine, i.e., crankshaft bearings, piston pin bearings and piston to wall contact

sur-faces, require oil mixed with the gasoline for lubrication. Failure to add oil to the gasoline or

failure to Mix oil with the gasoline at the appropriate ratio Will cause major engine damage and will

void your warranty. For your fuel premix, use MARUYAMA Premium Two-Stroke Oil Mix, or

equivalent ISO-L-EGD & JASO FC oil with a minimum 89 octane high Quality gasoline. MARUYAMA

two-stroke oil is spe-cially formulated to meet the requirements of high-performance, low-emission

air-cooled two-stroke engines. Use of other oils may lead to service issues which may Not be

covered by your warranty.

FUEL MIXTURE:

When using genuine MARUYAMA 50:1 Two-Stroke Oil, or a quality oil designed

for two-stroke air-cooled engines, oil ratio is 50 parts gasoline to 1 part oil or 50:1.

CAUTION! If MARUYAMA oil is not used, never use a mixing ratio less than 50:1 regardless of

the oil package mixing instructions. Ratios less the 50:1, (for example, 60:1, 80:1, 100:1),

reduce the amount of lubrication to the internal moving parts of the engine and can cause

damage.

FUEL MIXTURE CHART:

Gasoline

MARUYAMA 50:1 Two-Stroke Oil

Gasoline

MARUYAMA 50:1 Two-Stroke Oil

1 gallon 2.6 oz. 1 litre 20mL

2 1/2 gallons 6.4 oz. 2 litre 40mL

5 gallons 12.8 oz. 5 litre 100mL

MIXING INSTRUCTIONS:

Always mix fuel and oil in a clean container approved for gasoline.

Mark the container to identify it as fuel mix for the Hedge Trimmer. Use regular unleaded gasoline

and fill the container with half the required amount of gasoline. Pour the correct amount of oil

into the container then add the remaining amount of gasoline. Close the container tightly and

shake it momentarily to evenly mix the oil and the gasoline before filling the fuel tank on the Hedge

Trimmer.

When refilling the Hedge Trimmer fuel tank, clean around the fuel tank cap to prevent dirt and

debris for entering the tank during cap removal. Always shake the premix fuel container

momentarily before filling the fuel tank.

Always use a spout or funnel when fueling to reduce fuel spillage. Only fill the tank to within 1/4-

1/2 inch (6mm-13mm) from the top of the tank. Avoid filling to the top of the tank filler neck.





  









English

｜  ｜

NOTE:

1. Never mix gasoline and oil directly in the Hedge Trimmer fuel tank.

CAUTION!

1. Do not use National Marine Manufacturerʼs Association (NMMA) or BIA certified oils. This type

or two-stroke engine oil does not have the proper additives for air-cooled, two-stroke engines

and can cause engine damages.

2. Do not use automotive motor oil. This type of oil does not have the proper additives for air-

cooled, two-stroke engines and can cause engine damage.

ADJUSTING THE CUTTING BLADES

CAUTION-DO NOT TOUCH THE SHARPENED EDGES OF THE CUTTING

BLADES. THE CUTTING BLADES ARE EXTREMELY SHARP AND

DANGEROUS AT ALL TIMES. ALWAYS WEAR GLOVES TO HELP PROTECT

YOUR HANDS AND FINGERS FROM INJURY.

Before operating the Hedge Trimmer it is necessary to check the adjustment of the cutting

blades. Blades that are too loose may vibrate, and will not provide a clean, smooth cut.

CAUTION-BLADES THAT ARE TOO TIGHT CAN CAUSE OVERLOADING

WHICH MAY DAMAGE THE EQUIPMENT.

To adjust the cutting blades, refer to the illustrations and locate the screws.

Loosen the nuts.

Gently turn the screws in until snug, then turn the

screws back out one-fourth to a half. While hold-

ing the screws in place, tighten the nuts. Liberally

coat the cutting blades with light oil. Start the

engine and operate the Hedge Trimmer at full

speed for at least one minute. Stop the engine,

and when the blades are motionless, touch the

blades with your hand.

The blades should be warm, but if they are too hot

to touch, loosen the screws 1/8 turn.

nut

guide bar

washer

screw

nuts

lower blade

upper blade

screws

English

｜  ｜

STARTING AND STOPPING PROCEDURE

Before Starting The Engine:

Fill the fuel tank as instructed in the BEFORE OPERATION section

of this manual. Rest the Hedge Trimmer on the ground. Make sure that the cutting blades are

clear of branches, shrubs, debris, etc. Keep all bystanders, children and animals away from the

working area.

STARTING THE ENGINE

The carburetors on MARUYAMA engines contain a choke

system.

1. Push and release the fuel primer bulb located on the

bottom of the carburetor until air bubble free fuel is

seen flowing through the clear fuel return hose back to

the fuel tank.

2. Move the choke lever to the closed position “

”.

When the engine is warm, move the choke lever to the

open position “

”.

3. Set the engine stop switch to the “ON” position.

4. Lock the throttle trigger in the fast-idle start position.

Before starting the engine, place the machine on the ground and make sure the blade is

free from branches and stones.

choKe leVer

priMer bulb

Fuel-return line

puMp

on

oFF

BH24 BH24S

Fast-idle locK

idle position

Fast-idle

position

Fast-idle locK

idle position

Fast-idle position

English

｜  ｜

5. Grasp the starter grip and slowly pull the starter cord out until you feel some resistance, then

pull the cord quickly and powerfully. Pull the starter grip until the engine starts. After the

engine is started, move the choke lever to the open position, then squeeze and release the

throttle trigger to allow it to return to the idle position.

6. After starting, allow the engine to run a few minutes to warm it up before using.

NOTE:

1. Do not pull the starter cord out completely.

2. Do not release the starter cord from the fully extended position.

To Stop The Engine:

1. Release the throttle trigger.

2. Slide the stop switch to the “STOP” position.

CARBURETOR ADJUSTMENT

This Hedge Trimmer is equipped with non-adjustable fuel mixture carburetor. The engine idle

speed is the only adjustment to the Operator.

The cutting blades may be moving during idle speed adjustment. Wear the recommended

personal protective equipment and observe all safety instructions. Keep hands and body away from

blade area.

Engine Idle Speed:

When the throttle trigger is released the engine should

return to an idle speed which is 2700-3300 rpm or just

below clutch engagement speed. The cutting blades

must not move and the engine should not stall (stop

running) at engine idle speed.

The engine idle speed is adjusted by rotating the idle

speed screw on the carburetor. Turning the idle speed

screw in (clockwise) increases engine speed while

turning the screw out decreases engine speed.

If idle speed adjustment is necessary and after adjustment the cutting blades move or the

engine stalls,

stop using the Hedge Trimmer immediately!

Contact your local authorized MARUYAMA Dealer for assistance and servicing.

idle speed

adjustMent

screw

English

｜  ｜

OPERATING THE POWER HEDGE TRIMMER

CAUTION—Read the WARNING on page (10) concerning the proper use of the

Hedge Trimmer.

The MARUYAMA Hedge Trimmer is designed for cutting and trimming foliage and small branches

up to 1/4 inches (6mm) in diameter. Although the MARUYAMA Hedge Trimmer is capable of

cutting larger diameter branches, wear and tear of the machine would be proportionally increased.

CAUTION—Always wear gloves and protective clothing when operating the Hedge

Trimmer.

If the cutting blades become jammed, stop the engine immediately. Make certain all moving parts

have stopped and disconnect the spark plug before inspecting the equipment for damage. Never

use a Power Hedge Trimmer that has chipped, cracked, or broken cutting blades.

REGULAR MAINTENANCE

Maintenance, replacement or repair of emission control devices and systems may be performed by

any repair establishment or individual; however, warranty repairs must be performed by a dealer

or service center authorized by MARUYAMA Manufacturing Company, Inc. with Maruyama U.S.,

Inc. The use of parts that are not equivalent in performance and durability to authorized parts may

impair the effectiveness of the emission control system and may have a bearing on the outcome of a

warranty claim.

AIR FILTER

Maintenance Interval:

The air filter should be cleaned

daily or more often when working in extremely dusty condi-

tions and replaced after every 100 hours of operation.

Maintenance:

Push and open the air filter cover.

Remove the foam filter. Clean the filter with warm, soapy

water. Let the filter completely dry. Lightly apply SAE 30

motor oil to the foam filter and squeeze out all excess oil.

Reassemble the filter and filter cover.

FUEL FILTER

Maintenance Interval:

The fuel filter should be replaced

after every 100 hours of operation.

Maintenance:

The fuel filter is attached to the end of the

fuel pick-up hose inside the fuel tank. To replace the fuel

filter, first make sure the fuel tank is empty. Remove the

fuel cap. Using a wire hook, gently pull the fuel filter out

though the fuel filter opening. Grasp the fuel hose next to

the fuel filter fitting and remove the filter

but do not

FoaM Filter

air Filter

coVer

open

Fuel tanK

wire

Fuel Filter

push

English

｜  ｜

release the hose

. While still holding on to the fuel hose, attach the new fuel filter. Drop the fuel

filter back into the fuel tank. Make sure that the fuel filter is not stuck in a corner of the tank and

that the fuel hose is not doubled over (kinked) before refueling.

SPARK PLUG

Maintenance Interval:

The spark plug should be remove from the engine and checked after each

25 hours of operation and replaced after every 100 hours of operation.

Maintenance:

With the engine at ambient (room) temperature,

twist the high tension lead boot on the spark plug back and forth

a couple of times to loosen boot then pull the boot off of the spark

plug. Remove the spark plug. The electrodes can be cleaned

with a stiff brush. Adjust the electrode air gap to 0.6

—

0.7 mm

(0.024

—

0.028 in.). Replace the spark plug if it is oil-fouled,

damaged or if the electrodes are worn down.

Do not

overtighten the spark plug when installing.

The tightening

torque is 10.7

—

16.6 Nm (95

—

148 in. lbs.). Reinstall the cylinder and muffler covers.

CYLINDER COOLING FINS

Maintenance Interval:

The cylinder cooling fins should be cleaned after every 25 hours of opera-

tion or once a week which ever comes first. Air must flow freely around and through the cylinder

cooling fins to prevent engine overheating. Leaves, grass, dirt and debris buildup on the fins will

increase the operating temperature of the engine which can reduce engine performance and

short en engine life.

Maintenance:

With the engine at ambient (room) temperature, remove the two tapping screws

(FIG.1). Remove the four socket head screws on the plate, and remove the plate. Remove the

three socket head screws(FIG.2). Push the pawl, and pull the fan cover(FIG.3, 4). Clean all dirt

and debris from the cooling fins and from around the cylinder base. Reinstall fan cover and plate.

tips

0.6

—

0.7 mm

(0.024"

—

0.028")

1 2

La page charge ...

Maruyama BH24 Le manuel du propriétaire

Maruyama BH24 Le manuel du propriétaire

dans d''autres langues

Documents connexes