Hitachi CG 23ECP(SL) Safety Instructions And Instruction Manual

Catégorie
Coupe-herbe
Taper
Safety Instructions And Instruction Manual

Ce manuel convient également à

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this manual
BEFORE operating the power tool. Please keep this manual available for other users and owners before they
use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de
sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de
lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la
disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi
doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede provocar lesiones
graves o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este
manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras
personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
CG 23ECP (SL) / CG 23ECP (SLB)
Grass Trimmer
Coupe-Herbes
Motoguadañas
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
CG23ECP(SL)
2
English
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand
their meaning before use.
It is important that you read,
fully understand before use, and
observe the following safety
precautions and warnings.
Careless or improper use of the
unit may cause serious or fatal
injury.
Choke - Run position (Open)
Choke - Start position
(Closed)
Read, understand and follow all
warnings and instructions in this
manual and on the unit.
START
On/Start
Always wear eye, head and ear
protectors when using this unit.
STOP
O /Stop
Do not use metal/rigid blades
when this sign is shown on the
unit.
Fuel and oil mixture
Keep all children, bystanders
and helpers 15 m away from
the unit. If anyone approaches
you, stop the engine and cutting
attachment immediately.
Idle speed adjustment
Priming pump
Be careful of thrown objects.
Hot surface – Contact with
hot surface can cause serious
burns.
/min
Shows maximum shaft speed. Do
not use the cutting attachment
whose max rpm is below the
shaft rpm.
Indicate handle location.
Arrows which show limits for
handle positioning.
Gloves should be worn
when necessary, e.g., when
assembling cutting equipment.
Indicates cutting attachment
guard location for a trimmer
head or semi-auto cutting
head.
Use anti-slip and sturdy footwear.
Before using your machine
• Read the manual carefully.
• Check that the cutting equipment is correctly assembled and adjusted.
• Start the unit and check the carburetor adjustment. See “MAINTENANCE”.
3
English
10
12
1
3
13
9
20
18
19
17
16
6
15
4
CG23ECP(SLB)
7
2
11
13
5
8
21
8
13
4
5
14
6
7
11
2
CG23ECP(SL)
Contents
WHAT IS WHAT .................................................... 3
WARNINGS AND SAFETY INSTRUCTIONS ........ 4
WARRANTY .......................................................... 6
SPECIFICATIONS ................................................. 7
ASSEMBLY PROCEDURES ................................. 8
OPERATING PROCEDURES .............................. 10
MAINTENANCE .................................................. 12
WHAT IS WHAT
Since this manual covers several models, there may
be some di erence between pictures and your unit.
Use the instructions that apply to your unit.
1. Fuel cap
2. Throttle trigger
3. Starter handle
4. Cutting attachment guard
5. Cutting attachment
6. Drive shaft tube
7. Handle
8. Ignition switch
9. Spark plug
10. Priming bulb
11. Throttle trigger lockout
12. Choke lever
13. Engine
14. Gear case
15. Cutter case
16. Combi box spanner
17. Handling instructions
18. Goggles
19. Hex bar wrench
20. Top cover
21. Spanner
4
English
WARNING
The engine exhaust from this product contains
chemical known to the State of California to cause
cancer, birth defects or other reproductive harm.
WARNINGS AND SAFETY
INSTRUCTIONS
Pay special attention to statements preceded by the
following words:
WARNING
Indicates a strong possibility of severe personal
injury or loss of life, if instructions are not
followed.
CAUTION
Indicates a possibility of personal injury or
equipment damage, if instructions are not
followed.
NOTE
Helpful information for correct function and use.
Operator safety
Always wear a safety face shield or goggles.
Approved protective goggles comply with
standard ANSI Z87.1 in the USA.
Always wear heavy, long pants, non-slip boots,
gloves and a long-sleeve shirt. Do not wear
loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair so it is above shoulder
length.
Do not operate this tool when you are tired,
ill or under the in uence of alcohol, drugs or
medication.
Never let a child or inexperienced person operate
the machine.
Wear approved hearing protection.
Long-term exposure to noise can result in
permanent hearing impairment.
Pay attention to your surroundings. Be aware of
any bystanders who may be signaling a problem.
Remove safety equipment immediately upon
shutting o engine.
Wear head protection.
Never start or run the engine inside a closed
environment, such as a room or building.
Breathing carbon monoxide exhaust fumes can
kill.
Keep handles free of oil and fuel.
Keep hands away from cutting equipment.
Do not grab or hold the unit by the cutting
equipment.
When the unit is turned o , make sure the cutting
attachment has stopped before the unit is set
down.
When operation is prolonged, take a break from
time to time so that you may avoid possible
Hand-Arm Vibration Syndrome (HAVS) which is
caused by vibration.
Do not operate the tool at night or under bad
weather conditions when visibility is poor. And do
not operate the tool when it is raining or right after
it has been raining.
Working on slippery ground could lead to an
accident if you lose your balance.
Do not start the engine if there are any
ammables such as dry leaves, waste paper or
fuel in the vicinity.
Gloves should be worn when installing or
removing the cutting attachment. Failure to do so
may result in injury.
WARNING
Always operate the tool with proper
protective equipment and clothing. Failure to
do so may result in accidents such as burns
or injuries.
Do not touch the spark plug area or high
voltage during operation. Doing so may
result in electric shock.
Do not allow children near the tool during
operation.
Do not touch the engine, top cover or
exhaust vent during or shortly after
operation. Doing so may result in burn or
injury.
Antivibration systems do not guarantee that
you will not sustain Hand-Arm Vibration
Syndrome or carpal tunnel syndrome.
Therefore, continual and regular users
should monitor closely the condition of
their hands and ngers. If any symptoms
of the above appear, seek medical advice
immediately.
If you are using any medical electric/
electronic devices such as a pacemaker,
consult your physician as well as the device
manufacturer prior to operating any power
equipment.
Unit/machine safety
Inspect the entire unit/machine before each use.
Replace damaged parts. Check for fuel leaks
and make sure all fasteners are in place and
securely tightened.
Replace parts that are cracked, chipped or
damaged in any way before using the unit/
machine. Faulty parts may increase the risk of
accidents and may lead to an injury.
Make sure the cutting attachment is properly
installed and securely fastened.
5
English
Make sure the cutting attachment guard and
harness are properly attached. Do not operate
if cutting attachment guard and harness is not
properly attached.
Keep others away when making carburetor
adjustments.
Use only accessories as recommended for this
unit/machine by the manufacturer.
Before operation, make sure that there are no
tools such as the adjustment key or spanner still
attached to the unit.
WARNING
Never modify the unit/machine in any way.
Do not use your unit/machine for any job
except that for which it is intended.
Non-authorized modi cations and/or
accessories may result in serious personal
injury or the death of the operator or others.
Fuel safety
Mix and pour fuel outdoors where there are no
sparks and ames.
Use a container approved for fuel.
Move at least 10 ft (3 m) away from fueling site
before starting engine.
Slowly remove the fuel cap only after stopping
the engine. Do not remove the fuel cap during
operation.
Empty the fuel tank before storing the unit/
machine. It is recommended that the fuel be
emptied after each use. If fuel is left in the tank,
store so fuel will not leak.
WARNING
Fuel is easy to ignite or get explosion or
inhale fumes, so that pay special attention
when handling or lling fuel.
Do not smoke or allow smoking near fuel
or the unit/machine or while using the unit/
machine and fueling or mixing fuel.
Wipe up all fuel spills before starting engine.
Store unit/machine and fuel in area where
fuel vapors cannot reach sparks or open
ames from water heaters, electric motors or
switches, furnaces. etc.
When using the unit in dry areas, make sure
that re extinguishing equipment is readily
available.
If you shut o the engine for refueling, make
sure the unit has cooled down before adding
fuel.
Cutting safety
Do not cut any material other than grass and
brush.
Clear the area to be cut before each use.
Remove objects which can be thrown or become
entangled in the cutting attachment.
For respiratory protection, wear an aerosol
protection mask when cutting the grass after
insecticide is scattered.
Keep others including children, animals,
bystanders and helpers outside the 50 ft (15 m)
hazard zone. There is still a risk of injury from
thrown object. Bystanders should be encouraged
to wear eye protection. Stop the engine
immediately if you are approached.
Please exercise caution as engine startup may
be delayed after pulling the starter handle.
Always keep the engine on the right side of your
body.
Hold the unit/machine rmly with both hands.
Keep rm footing and balance. Do not over-
reach.
Losing your balance during work may lead to an
injury.
Keep all parts of your body away from the mu er
and cutting attachment when the engine is
running.
Keep cutting attachment below knee level.
Please exercise caution when operating in areas
where electrical cables or gas pipes are present.
Do not operate the cutting attachment for
anything but clearing grass or bushes. Avoid
operations where the cutting attachment may
touch water such as puddles or dig into dirt.
Failure to do so may result in injury or damage to
the unit.
Avoid prolonged use at low speed range in which
vibration is high. Doing so may result in engine
damage.
When relocating to a new work area, or
inspecting, adjusting or exchanging the unit’s
cutting attachments, accessories, etc., be sure
to shut o the machine and ensure that all cutting
attachments are stopped.
Never place the machine on the ground when
running.
Never touch the cutting attachment when it is
rotating.
Always ensure that the engine is shut o and any
cutting attachments have completely stopped
before clearing debris or removing grass from the
cutting attachment.
Always carry a rst-aid kit when operating any
power equipment.
Turn o
the engine and make sure the cutting
attachment has come to a full stop before
removing the unit from your body or before
leaving the unit unattended.
6
English
If you accidentally bump or drop the unit,
inspect it immediately to make sure there are no
damage, cracks or deformations.
If the tool is operating poorly and produces
strange noise or vibrations, turn o the engine
immediately and ask your dealer to have it
inspected and repaired.
Continued use under these conditions could lead
to injury or tool damage.
Use in accordance with local laws and
regulations.
Maintenance safety
Maintain the unit/machine according to
recommended procedures.
Disconnect the spark plug before performing
maintenance except for carburetor adjustments.
Keep others away when making carburetor
adjustments.
Use only genuine Hitachi replacement parts as
recommended by the manufacturer.
CAUTION
Do not disassemble the recoil starter. There
is a possibility of personal injury with recoil
spring.
WARNING
Improper maintenance could result in
serious engine damage or in serious
personal injury.
Transport and storage
Carry the unit/machine by hand with the engine
stopped and the mu er away from your body.
Allow the engine to cool, empty the fuel tank
before storing or transporting.
Secure the machine during transport to prevent
loss of fuel, damage or injury.
Empty the fuel tank before storing the unit/
machine. It is recommended that the fuel be
emptied after each use. If fuel is left in the tank,
store so fuel will not leak.
Store unit/machine out of the reach of children.
Clean and maintain the unit carefully and store it
in a dry place.
Make sure engine switch is o when transporting
or storing.
When transporting and storing, either remove the
cutting attachment or place the blade cover over
the blade.
You have to secure the machine during transport
to prevent loss of fuel, damage or injury.
If a warning label cannot be read, peels o or
becomes indistinct, replace it with a new one. To
purchase new labels, contact Hitachi Authorized
Service Centers.
If situations occur which are not covered in this
manual, take care and use common sense. Contact
Hitachi Authorized Service Centers if you need
assistance.
WARRANTY
The warranties provided by Hitachi Koki U.S.A., Ltd.
are explained in the warranty card enclosed with this
product titled “Hitachi Outdoor Power Equipment
Limited Warranty”.
Model CG23ECP(SLB) is NOT intended for
commercial use, and therefore, NO warranty is
provided to their commercial applications and rental
applications. Therefore, the two year warranty
for “the rst commercial end user” and one year
warranty for “rental applications” mentioned in the
warranty card are provided on CG23ECP(SL), but
NOT on CG23ECP(SLB).
7
English
SPECIFICATIONS
Model CG23ECP (SL) CG23ECP (SLB)
Engine Size (cu. in.) 1.37 (22.5 ml)
Spark Plug
TORCH AC6RA
(NGK CMR6A)
Fuel Tank Capacity ( . oz) 16.2 (0.48 l)
Dry Weight (Ibs) 10.8 (4.9 kg) 9.5 (4.3 kg)
Sound pressure level
LpA (dB (A))
(ISO22868)
Equivalent
95.3 94.8
Measured sound
power level LwA
(dB (A))
(
ISO
22868)
Racing
112 109.3
Guaranteed sound
power level LwA
(dB (A))
(
ISO
22868)
Racing
115
Vibration level (m/s
2
)
(ISO22867)
Equivalent (Front / Left handle)
Equivalent (Rear / Right handle)
Uncertainty
6.0
6.3
1.5
7.3
4.8
1.5
NOTE
Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration
levels under various working conditions with the following time distribution:
* 1/2 idle, 1/2 racing.
All data subject to change without notice.
8
English
ASSEMBLY PROCEDURES
Installation of handle (Fig. 1)
Attach the handle to the drive shaft tube.
Adjust the location to the most comfortable position
before operation.
Make sure to securely attach the handle with the 4
bolts.
1
Fig. 1
NOTE
If your unit has handle location label (1) on drive
shaft tube, follow the illustration.
WARNING
Do not use metal or plastic blade cutting
attachments.
Installation of cuttingt attachment guard
WARNING
Do not start or operate unit unless each
guard is properly assembled to unit.
If an incorrect or faulty guard is tted, this
may cause serious personal injury.
CAUTION
Some cutting attachment guards are
equipped with sharp line limiters. Be careful
with handling it.
(CG23ECP (SL))
Aligning to the position indicated by the guard
location label (2), rmly secure the cutting
attachment guard to the drive shaft tube with the bolt
(3) and guard bracket (4). (Fig. 2)
4
2
3
Fig. 2
(CG23ECP (SLB))
Insert the cutter case between the guard bracket
and cutting attachment guard, and secure it with the
bolt. (Fig. 3)
Fig. 3
WARNING
lf unit is operated without a sharp line
limiters, the line will become too long, the
engine will overheat, and engine damage
may occur.
Check sharp line limiters surely cut nylon
line when operating.
Installation of cutting attachment
WARNING
Install the cutting attachment properly
and securely as instructed in the handling
instructions.
If not attached properly or securely, it may
come o and cause serious and/or fatal
injury.
Do not install or remove cutting attachments
while the engine is running.
Always use genuine Hitachi cutting
attachments and metal ttings.
Installation of semi-auto cutting head
1. Function
Automatically feeds more nylon cutting line
when it is tapped at low rpm (not greater than
6,000 min
–1
).
Speci cations
Code No.
Type of
attaching
screw
Direction of
rotation
Size of
attaching
screw
6600570
Female
screw
Counterclockwise
M10×P1.25-
LH
6601376
Female
screw
Clockwise
M8xP1.25-
RH
Applicable nylon cord
Cord diameter: 3/22˝ (Φ2.4 mm) Length: 16.3 ft (5 m)
9
English
2. Precautions
The case must be securely attached to the cover.
Check the cover (5), case (6) and other
components for cracks or other damage. (Fig. 4)
Check the case and button for wear.
If there is a hole in the bottom (7) of the button,
change the new parts immediately. (Fig. 4)
7
6
5
Fig. 4
The cutting head must be securely mounted to
the unit’s gear case/cutter case.
If the cutting head does not feed cutting line
properly, check that the nylon line and all
components are properly installed. Contact
Hitachi Authorized Service Centers if you need
assistance.
WARNING
For Hitachi heads, use only exible,
non-metallic line recommended by the
manufacturer. Never use wire or wire ropes.
They can break o and become a dangerous
projectile.
3. Installation (Fig. 5)
(CG23ECP (SL))
Insert the Hex bar wrench (8) into the hole of the
gear case and groove of the Cutter holder (9) in
order to lock the shaft.
Install cutting head on gear case of grass
trimmers. The mounting nut is left-hand-
threaded. Turn clockwise to loosen/counter-
clockwise to tighten.
8
9
Fig. 5
(CG23ECP (SLB)) (Fig. 6)
Insert the Hex bar wrench (8) into the hole of the
cutter case in order to lock the drive shaft tube.
Install cutting head on cutter case of grass
trimmers. The mounting nut is right-hand-
threaded. Turn counter-clockwise to loosen/
clockwise to tighten.
8
Fig. 6
4. Adjusting line length
Set the engine speed as low as possible and tap
the head on the ground. The nylon line will be
drawn out about 1-3/16˝ (3 cm) with each tap.
(Fig. 7)
Fig. 7
Also, you can extend the nylon line by hand but
the engine must be completely stopped. (Fig. 8)
Fig. 8
Adjust the nylon line to the proper length
of 4-11/32˝–5-1/2˝ (11–14 cm) before each
operation.
10
English
OPERATING PROCEDURES
Fuel (Fig. 9)
Fig. 9
WARNING
The trimmer is equipped with a two-stroke
engine. Always run the engine on fuel, which
is mixed with oil.
Provide good ventilation, when fueling or
handling fuel.
Fuel contains highly ammable and it is
possible to get the serious personal injury
when inhaling or spilling on your body.
Always pay attention when handling fuel.
Always have good ventilation when handling
fuel inside building.
Fuel
Always use branded 89 octane unleaded
gasoline.
Use genuine two-cycle oil or use a mix between
25:1 to 50:1, please consult about the mixture
ratio to Hitachi Authorized Service Centers.
Only for the state of California at 50:1.
If genuine oil is not available, use an anti-oxidant
added quality oil expressly labeled for air-cooled
2-cycle engine use (JASO FC GRADE OIL or
ISO EGC GRADE). Do not use BIA or TCW
(2-stroke water-cooling type) mixed oil.
Never use multi-grade oil (10 W/30) or waste oil.
Never mix fuel and oil in machine’s fuel tank.
Always mix fuel and oil in a separate clean
container.
Always start by lling half the amount of gasoline,
which is to be used.
Then add the whole amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
Mix (shake) the fuel-mix thoroughly before lling the
fuel tank.
Mixing amount of two-cycle oil and gasoline
Gasoline (Liter)
Two-cycle oil (ml)
Ratio 50:1 Ratio 25:1
0.5 10 ——— 20
1 20 ——— 40
2 40 ——— 80
4 80 ——— 160
Fueling
WARNING
Always shut o the engine and let it cool for
a few minutes before refueling.
Do not smoke or bring ames or sparks near
the fueling site.
Slowly open the fuel tank, when lling up
with fuel, so that possible over-pressure
disappears.
Tighten the fuel cap carefully, after fueling.
Always move the trimmer at least 10 ft (3 m)
from the fueling area before starting.
Always wash any spilled fuel from clothing
immediately with soap.
Be sure to check for any fuel leakage after
refueling.
Before fueling, in order to remove static
electricity from the main body, the fuel
container and the operator, please touch the
ground that is slightly damp.
Before fueling, clean the tank cap area carefully,
to ensure that no dirt falls into the tank. Make sure
that the fuel is well mixed by shaking the container,
before fueling.
Starting
WARNING
Before starting the tool, ensure that the
cutting attachment is not touching any
objects or the ground.
Otherwise, the cutting attachment may
unexpectedly rotate and cause an injury.
Ensure that the cutting attachment does not
rotate while the engine is idling. If it does
rotate, adjust the idle speed according to the
instructions in “Idle speed adjustment” in
the “MAINTENANCE” section. If the cutting
attachment still rotates after this adjustment,
immediately stop the engine and cease use,
then bring the tool to the nearest Hitachi
Authorized Service Center.
11
English
1. Starting the cold engine
(1) Set ignition switch (10) to ON position. (Fig. 10)
10
Fig. 10
(2) Push priming bulb (11) about ten times so that
fuel ows into carburetor. (Fig. 11)
11
Fig. 11
(3) Set choke lever (12) to START position (closed)
(A). (Fig. 12)
AA
B
B
12
Fig. 12
(4) Pull recoil starter briskly, taking care to keep the
handle in your grasp and not allowing it to snap
back. (Fig. 13)
Fig. 13
(5) When you hear the engine want to start, return
choke lever to RUN position (open) (B). (Fig. 12)
(6) Pull recoil starter briskly again. (Fig. 13)
NOTE
If engine does not start, repeat procedures from
2 to 5.
(7) Then allow the engine about 2–3 minutes to
warm up before subjecting it to any load.
(8) Check that the cutting attachment does not rotate
when the engine is idling.
2. Starting the warm engine
Use only 1, 6 and 8 of the starting procedure for a
cold engine.
If the engine does not start, use the same starting
procedure as for a cold engine.
Cutting
WARNING
Always use the harness (if so equipped)
and wear the proper attire and protective
equipment when operating the unit. (Fig. 14)
Keep others including children, animals,
bystanders and helpers outside the 15 m
hazard zone. Stop the engine immediately if
you are approached. (Fig. 15)
When grass or vines wrap around
attachment, stop engine and attachment
and remove them. Continuing operation
with grass or vines wrapped around the
attachment may result in damages such as
early abrasion of the clutch.
Fig. 14 Fig. 15
NOTE
Use in accordance with local laws and
regulations.
12
English
Using a semi-auto cutting head
Set the engine at high speed when using this
attachment.
Cut grass from left to right. The cut grass will
be discharged away from the body, minimizing
transfer to your clothes. (Fig. 16)
Cut grass from right to left as the cutting
attachment of the curved drive shaft tube model
rotates clockwise.
With nylon cord, use about 3/4” (2 cm) of the end
of the cord to cut grass. Using the full length of
the cord will reduce rotation speed and make
cutting di cult.
Fig. 16
NOTE
Automatically feeds more nylon cutting line
when it is tapped at low rpm (not greater than
6,000 min
-1
).
WARNING
This product is equipped with a line limiter
that will automatically cut any excess cord.
When operating the unit, do not remove the
guard or line limiter.
As the resistance is greater for nylon cords
as opposed to blades, mishandling could
increase engine load and result in damage.
Do not use with the engine set at low
speeds. If the engine speed is low, grass
may wrap around the attachment, causing
the clutch to slip which could result in clutch
abrasion.
With nylon cord cutters, always use over
5-7/8” (15 cm) of cord. If the length of
the cord is too short, rotation speed will
increase and may cause damage to the
nylon cord cutter. As the curved drive shaft
tube model in particular is not equipped with
a deceleration mechanism, the possibility
of increased rotation speed for the cutting
attachment is high.
Stopping (Fig. 17)
Decrease engine speed and run at an idle for a few
minutes, then turn o ignition switch (10).
10
Fig. 17
WARNING
A cutting attachment can injure while it
continues to spin after the engine is stopped
or Throttle trigger is released. When the
unit is turned o , make sure the cutting
attachment has stopped before the unit is
set down.
MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR
OF THE EMISSION CONTROL DEVICES AND
SYSTEMS MAY BE PERFORMED BY ANY NON-
ROAD ENGINE REPAIR ESTABLISHMENT OR
INDIVIDUAL.
Carburetor adjustment (Fig. 18)
Fig. 18
The carburetor is a precision part that mixes air and
fuel, and it is designed to ensure high performance
from the engine. Before the tool is shipped from
the factory, its carburetor is adjusted during a
test run. Only make adjustments if it is necessary
because of environmental conditions (the climate or
atmospheric pressure), the type of fuel, the type of
two-cycle oil, etc.
13
English
WARNING
Because the carburetor is manufactured
with a high degree of precision, do not
disassemble it.
For this product, the only setting of the
carburetor that can be adjusted is the idle
speed (T).
Never start the engine without the complete
clutch cover and tube assembled! Otherwise
the clutch can come loose and cause
personal injuries.
T = Idle speed adjustment screw.
Idle speed adjustment (T)
WARNING
When the engine is stopped, do not
excessively turn the idle speed adjustment
screw (T) in a clockwise direction.
Otherwise, when the engine starts, the
cutting attachment may unexpectedly rotate
and cause an injury.
Do not adjust the idle speed adjustment
screw (T) for any reason other than to adjust
the idling.
Run the engine while adjusting the idling.
(1) If the engine stops during idling
Start the engine, and slowly turn the idle speed
adjustment screw (T) in a clockwise direction
until it is in a position at which the engine rotates
smoothly. At that time, ensure that the cutting
attachment is not spinning.
(2) If the cutting attachment rotates during idling
Slowly turn the idle speed adjustment screw (T)
in a counter-clockwise direction until it is in a
position at which the cutting attachment does not
rotate. At that time, ensure that the rotation of the
engine is smooth.
WARNING
If the cutting attachment still rotates after
adjustment of the idle speed adjustment
screw (T), immediately stop the engine and
cease use, then contact the nearest Hitachi
Authorized Service Center.
Air lter (Fig. 19)
The air lter (13) must be cleaned from dust and dirt
in order to avoid:
Carburetor malfunctions
Starting problems
Engine power reduction
Unnecessary wear on the engine parts
Abnormal fuel consumption
Clean the air lter daily or more often if working in
exceptionally dusty areas.
13
Fig. 19
Cleaning the air lter
Open the air lter cover and remove the air lter
(13). Clean it.
Check that the lter is dry before reassembly.
An air lter that has been used for some time cannot
be cleaned completely. Therefore, it must regularly
be replaced with a new one. A damaged lter must
always be replaced.
NOTE
To put the air lter cover back into place, hook it
on the upper tabs and then attach it.
Fuel lter (Fig. 20)
Remove the fuel lter (14) from the fuel tank, and
replace it if it is dirty.
NOTE
A blocked fuel lter (14) can prevent the supply of
fuel and cause a rotation malfunction of the engine.
14
Fig. 20
Spark plug (Fig. 21)
The spark plug condition is in uenced by:
An incorrect carburetor setting
Wrong fuel mixture (too much oil in the gasoline)
A dirty air lter
Hard running conditions (such as cold weather)
These factors cause deposits on the spark plug
electrodes, which may result in malfunction and
starting di culties. If the engine is low on power,
14
English
Gear case (Fig. 23)
Check gear case or angle gear for grease level
about every 50 hours of operation by removing the
grease ller plug on the side of gear case.
If no grease can be seen on the anks of the
gears, ll the gear case with quality lithium based
multipurpose grease up to 3/4. Do not completely ll
the gear case.
Fig. 23
CAUTION
Make sure to remove any dirt or grit when
attaching the plug to its original position.
Before attempting inspection or maintenance
of the gear case, make sure the case has
cooled.
Semi-auto cutting head
Nylon line replacement
(1) Remove the case (17) by rmly pushing inward
the locking tabs with your thumbs as shown in
Fig. 24.
17
Fig. 24
(2) After removing the case, take out the reel and
discard the remaining line.
(3) Fold the new nylon line unevenly (approx. 10 cm)
in half as shown in picture.
Hook the U-shaped end of the nylon line into the
groove (18) on the center partition of the reel.
Wind both halves of the line on the reel in the
same direction, keeping each half of the line on
its own side of the partition. (Fig. 25)
di cult to start or runs poorly at idling speed, always
check the spark plug rst. If the spark plug is dirty,
clean it and check the electrode gap. Re-adjust
if necessary. The correct gap is 0.024˝ (0.6 mm).
The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly
eroded.
0.024˝
(0.6 mm)
Fig. 21
NOTE
In some areas, local law requires using a resistor
spark plug to suppress ignition signals. If this
machine was originally equipped with resistor
spark plug, use same type of spark plug for
replacement.
Flexible drive shaft (Fig. 22)
(CG23ECP (SLB))
Flexible drive shaft should be removed and
lubricated with good quality lithium grease every
20 hours. To remove the exible shaft, rst remove
screw (15), loosen bolt (16) and remove the cutter
case then pull the shaft out of the drive shaft tube.
Clean the shaft o and apply a generous coat of
lithium grease to it and insert if back into the drive
shaft tube, turn it unit it drops into place then install
the cutter case, install & tighten screw (15) and bolt
(16).
15
16
Fig. 22
15
English
4˝ (10 cm)
18
Fig. 25
(4) Push each line into the stopper holes (19),
leaving the loose ends approx. 4˝ (10 cm) in
length. (Fig. 26)
19
4˝ (10 cm)
4˝ (10 cm)
Fig. 26
(5) Insert both loose ends of the line through the
cord guide (20) when placing the reel in the case.
(Fig. 27)
20
19
Fig. 27
NOTE
When placing a reel in the case, try to line up the
stopper holes (19) with the cord guide (20) for
easier line release later.
(6) Place the cover over the case so that the cap
locking tabs (21) on the cover meet the long
holes (22) on the case. Then push the case
securely until it clicks into place. (Fig. 28)
22
21
Fig. 28
(7) The initial cutting line length should be approx.
4-11/32˝–5-1/2˝ (11–14 cm) and should be equal
on both sides. (Fig. 29)
4-11/32˝–5-1/2˝
(11-14 cm)
4-11/32˝–5-1/2˝
Fig. 29
For long-term storage
Drain all fuel from the fuel tank. Start and let engine
run until it stops. Repair any damage which has
resulted from use. Clean the unit with a clean rag, or
the use of high pressure air hose. Put a few drops
of two-cycle engine oil into the cylinder through the
spark plug hole, and spin the engine over several
times to distribute oil.
Cover the unit and store it in a dry area.
Maintenance schedule
Below you will nd some general maintenance
instructions. For further information please contact
Hitachi Authorized Service Centers.
Daily maintenance
Clean the exterior of the unit.
Check the cutting attachment guard for damage
or cracks. Change the guard in case of impacts
or cracks.
16
English
Check that the cutting attachment is properly
centred, sharp, and without cracks. An o -centre
cutting attachment induces heavy vibrations that
may damage the unit.
Check that the cutting attachment nut is
su ciently tightened.
Check that nuts and screws are su ciently
tightened.
Check that the unit is undamaged and free of
defects.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the
problem, consult your dealer or the Hitachi Authorized Service Center.
Condition Cause Remedy
Engine does
not start
Fuel
system
Fuel tank is empty or fuel level is
low
Fill the fuel tank with the correct fuel mix
(25:1-50:1)
Fuel tank contains old fuel (o ensive
odor)
Replace with new fuel
Too much fuel is absorbed and
spark plug is wet
1.
Disconnect the spark plug and allow
to dry
2. Pull the starter handle 5 or 6 times to
remove the surplus fuel
3. Attach the spark plug
4. Set the choke lever to RUN position
and pull the starter handle
Fuel lter is clogged with dirt Clean the fuel lter
Fuel pipe is bent or disconnected Ensure that the fuel ows smoothly
Carburetor malfunction
Contact Hitachi Authorized Service
Centers
Electrical
system
Stop switch lead has short-
circuited
Contact Hitachi Authorized Service
Centers
Spark plug is dirty Replace or clean the spark plug
Electrode gap is too big Adjust the gap to 0.6 mm
Poor connection between high
tension cable and spark plug
Reconnect
Electrical system malfunction
Contact Hitachi Authorized Service
Centers
Other
Mu er exhaust port is clogged
with carbon
Contact Hitachi Authorized Service
Centers for repair
Weekly maintenance
Check the starter, especially the cord.
Clean the exterior of the spark plug.
Remove the spark plug and check the electrode
gap. Adjust it to 0.024˝ (0.6 mm), or change the
spark plug.
Check that the angle gear is lled with grease up
to 3/4.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline.
Clean the exterior of the carburetor and the
space around it.
Clean the fan and the space around it.
17
English
Condition Cause Remedy
Engine starts
but cuts out
straightaway
Engine is apt to
cut out
Fuel
system
Fuel tank is empty or fuel level is
low
Fill the fuel tank with the correct fuel mix
(25:1-50:1)
Fuel tank contains old fuel (o ensive
odor)
Replace with new fuel
Two-cycle oil has not been added
Contact Hitachi Authorized Service
Centers
Choke lever is in START position Set the choke lever to RUN position
Air has got into fuel system Reconnect the fuel pipe or joint
Carburetor malfunction
Contact Hitachi Authorized Service
Centers
Electrical
system
Ignition failure
Spark plug failure Replace with new spark plug
Electrical system failure
Contact Hitachi Authorized Service
Centers
Other
Engine overheating
Wrong spark plug model
Replace with designated part
See “SPECIFICATIONS”
Dirty air cleaner Clean
Carbon clogging (mu er exhaust
port)
Clean
Insu cient compression (piston,
piston ring, cylinder)
Contact Hitachi Authorized Service
Centers
Abnormal vibration
Cutting attachment is not properly
installed
See “Installation of cutting attachment”
Handle, handle bracket or other
fastening part is loose
Check and tighten
Grass is wrapped round gear case Remove grass
Engine is running but blade
does not move
Movement is poor
Grass is wrapped round gear case Remove grass and dirt
Engine does not stop Stop switch failure
Set the choke lever to START position
to stop the engine
Cease use immediately and contact
Hitachi Authorized Service Centers
Engine stops when throttle
is closed
Idle speed is too low
Contact Hitachi Authorized Service
Centers
Blade continues rotating
when throttle is closed
Idle speed is too high
Throttle wire is too taut
Contact Hitachi Authorized Service
Centers
18
Français
SIGNIFICATION DES SYMBOLES
REMARQUE:
Certains appareils n’en sont pas pourvus.
Symboles
ATTENTION
Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur
signi cation avant d’utiliser l’outil.
Il est important que vous lisiez
et compreniez bien avant
utilisation et que vous respectiez
les précautions de sécurité
et avertissements suivants.
L’utilisation inattentive ou
inadéquate de cet appareil peut
provoquer des blessures graves
voire mortelles.
Utilisez des chaussures
antidérapantes et solides.
Etranglement – Position
marche (ouverte)
Etranglement – Position de
démarrage (fermé)
Lisez attentivement et respectez toutes
les instructions et tous les avertissements
donnés dans ce manuel et sur le produit.
START
Marche/Allumer
Utilisez toujours des lunettes de
protection ainsi qu’un casque et
des protections d’oreilles lorsque
vous utilisez ce produit.
STOP
Arrêt/Eteindre
N’utilisez pas de lames métalliques/
rigides lorsque ce signe apparaît sur
la machine.
Mélange carburant/huile
Maintenez les enfants, spectateurs
et aides à plus de 15 m de l’appareil.
Si quelqu’un s’approche de vous,
coupez immédiatemment le moteur
et arrêtez l’outil de coupe.
Réglage du ralenti
Pompe à amorcer
Faites attention aux projections
d’objets.
Surface chaude – Tout
contact avec une surface
chaude peut provoquer de
graves brûlures.
/min
Indique la vitesse maximale de
l’arbre. N’utilisez pas d’outil de coupe
dont la vitesse de rotation (nombre
de tours/minute) est inférieure à la
vitesse de rotation de l’arbre.
Indique l’emplacement
de la poignée. Flèches
pour indiquer les limites
concernant le positionnement
de la poignée.
Au besoin, utilisez des gants,
notamment lors du montage de
l’équipement de coupe.
Indique l’emplacement de
la protection de l’outil de
coupe pour un coupe-herbe
ou une tête de coupe semi-
automatique.
Avant l’utilisation de votre nouvelle machine
• Lisez attentivement le manuel d’utilisation.
• Véri ez que l’équipement de coupe est monté et réglé correctement.
• Démarrez la machine et véri ez le réglage du carburateur. Voir la section “ENTRETIEN”.
19
Français
10
12
1
3
13
9
20
18
19
17
16
6
15
4
CG23ECP(SLB)
7
2
11
13
5
8
21
8
13
4
5
14
6
7
11
2
CG23ECP(SL)
DESCRIPTION
Ce manuel étant commun à plusieurs modèles, vous
constaterez peut-être certaines di érences entre
les images et votre appareil. Suivez les instructions
relatives à votre modèle.
1. Bouchon de réservoir de carburant
2. Manette d’accélérateur
3. Poignée du démarreur
4. Protection de l’outil de coupe
5. Outil de coupe
6. Tube de transmission
7. Poignée
8. Contacteur d’allumage
9. Bougie
10. Poire d’amorçage
11. Manette de verrouillage
12. Levier d’étranglement
13. Moteur
14. Boîte de vitesse
15 Boîtier de l’outil de coupe
16. Clé à douille multiple
17. Mode d’emploi
18. Lunettes
19. Clé Allen
20. Couvercle supérieur
21. Clé pour contre-écrou
Sommaire
DESCRIPTION ..................................................... 19
PRÉCAUTIONS ET CONSIGNES DE SÉCURITÉ
....... 20
GARANTIE ........................................................... 23
CARACTÉRISTIQUES ......................................... 23
MONTAGE ........................................................... 24
UTILISATION ........................................................ 26
ENTRETIEN ......................................................... 29
20
Français
ATTENTION
Les gaz d'échappement du moteur de ce produit
contiennent des substances chimiques connues
dans l'État de la Californie pour causer le cancer, des
malformations congénitales ou d'autres anomalies
reproductives.
PRÉCAUTIONS ET CONSIGNES
DE SÉCURITÉ
Faites particulièrement attention aux stipulations
introduites par les mots ci-dessous:
AVERTISSEMENT
Information de première importance pour éviter
des dommages corporels graves ou mortels.
ATTENTION
Information importante a n d’éviter des
dommages corporels ou matériels.
REMARQUE
Information utile pour une utilisation et un
fonctionnement corrects de la machine.
Sécurité de l’utilisateur
Portez toujours une visière et des lunettes de
protection.
Les lunettes étanches de protection agréées sont
conformes à la norme ANSI Z87.1 aux États Unis.
Portez toujours un pantalon épais, des chaussures
antidérapantes, des gants et une chemise à
manches longues. Évitez les vêtements amples,
les shorts, les sandales et les pieds nus. Veillez
à ce que vos cheveux ne descendent pas au-
dessous des épaules.
Utilisez cette machine uniquement si vous êtes
en pleine possession de vos moyens physiques.
Évitez strictement la consommation d’alcool, de
drogue ou de médicaments.
Ne laissez jamais un enfant ou une personne
inexpérimentée se servir de ces machines.
Portez un dispositif de protection auditive agréé (3).
L’exposition prolongée à des sons forts peut
entraîner une dé cience auditive permanente.
Restez vigilant à tout ce qui vous entoure. Restez
attentif dans l’éventualité où une personne située
à proximité vous signalerait un problème.
Retirez les équipements de sécurité
immédiatement après avoir coupé le moteur de
l’outil.
Protégez-vous la tête.
Ne mettez jamais le moteur en marche dans un
environnement fermé, comme dans une pièce
ou à l’intérieur d’un bâtiment. L'inhalation de gaz
d’échappement au monoxyde de carbone peut
être mortelle.
Nettoyez les poignées de toute trace d’huile ou de
carburant.
N’approchez jamais les mains du guide-chaîne et
de la chaîne.
N’attrapez jamais et ne tenez jamais la machine
par l’extrémité du guide-chaîne.
Après l’arrêt de la machine, attendez l’arrêt
complet de l’outil de coupe avant de poser la
machine.
Lors d’une utilisation prolongée, veillez à pratiquer
des pauses régulières a n d’éviter des troubles
éventuels provoqués par les vibrations.
Ne pas utiliser l’outil de nuit ou sous de mauvaises
conditions météorologiques lorsque la visibilité
est mauvaise. Et n’utilisez pas l’appareil lorsqu’il
pleut ou tout de suite après une averse.
Travailler sur un sol glissant peut conduire à un
accident si vous perdez l’équilibre.
Ne démarrez pas le moteur s’il y a des matières
in ammables telles que des feuilles sèches, de
vieux papiers ou du carburant dans les alentours.
Au besoin, utilisez des gants, lors du montage
ou du dégagement de l’outil de coupe. Le non-
respect de cette précaution peut provoquer des
blessures.
ATTENTION
Toujours utiliser l’outil avec un équipement
de protection et des vêtements. Le non-
respect de cette consigne pourrait entraîner
des accidents comme des brûlures ou des
blessures.
Ne touchez pas à la zone d’étincelle ou à la zone
de haute tension pendant le fonctionnement.
Cela peut entraîner un choc électrique.
Ne laissez pas les enfants près de l’outil
pendant le fonctionnement.
Veuillez ne pas toucher le couvercle supérieur
du moteur ni le conduit d'aération pendant
ou tout de suite après l'utilisation. Cela peut
entraîner des brûlures ou des blessures.
Les systèmes anti-vibrations ne préviennent
pas de la maladie des doigts blancs, ni du
syndrome du canal carpien. Par conséquent,
en cas d’utilisation régulière et continue de
votre machine, surveillez soigneusement
l’état de vos mains et de vos doigts. Si l’un des
symptômes ci-dessus venait à apparaître, il
serait indispensable de vous faire examiner
immédiatement par votre médecin.
Si vous êtes équipé d’un appareillage médical
électrique/électronique tel qu’un stimulateur
cardiaque, consultez votre médecin et le
fabricant de cet appareillage avant d’utiliser
tout appareil électrique.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Hitachi CG 23ECP(SL) Safety Instructions And Instruction Manual

Catégorie
Coupe-herbe
Taper
Safety Instructions And Instruction Manual
Ce manuel convient également à

dans d''autres langues