BIO RAD DTE41027 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

User Manual
DTE4027
RFID
Reader
Module
REF
DTE4027
February 2014
DTE4027 RFID Reader Module
User Manual 1
Table of Contents
1
INTRODUCTION .............................................................................................................................. 6
1.1
General Description ................................................................................................................... 6
2
SPECIFICATIONS ............................................................................................................................ 6
2.1
Physical Specifications ............................................................................................................... 6
2.1.1
Dimensions ......................................................................................................................... 6
2.1.2
Weight ................................................................................................................................ 6
2.2
Technical Specifications ............................................................................................................. 6
2.2.1
General Specifications......................................................................................................... 6
3
SYSTEM DESCRIPTION .................................................................................................................. 7
3.1
Electrical Interface ..................................................................................................................... 7
3.2
Block Diagram ........................................................................................................................... 7
3.3
Mechanical Drawing ................................................................................................................... 8
4
INSTALLATION PROCEDURE ......................................................................................................... 9
4.1
Installation Requirements ........................................................................................................... 9
4.2
Installation ................................................................................................................................. 9
4.3
Command set ............................................................................................................................ 9
5
TROUBLESHOOTING ...................................................................................................................... 9
5.1
Error Messages.......................................................................................................................... 9
DTE4027 RFID Reader Module
User Manual 2
Bio-Rad Laboratories
7, rue de Madrid
67300 Schiltigheim
France
CAUTION
Please read through and familiarize yourself with the contents of the user manual.
ABOUT THIS MANUAL:
This manual is intended for design engineers and technicians. The following
topics are included:
Principles of Operation
Technical Specifications
Module in system integration
Troubleshooting Guide
Also included are electrical and mechanical drawings.
DTE4027 RFID Reader Module
User Manual 3
WARNING TO USERS IN THE UNITED STATES
Federal Communication Commission Interference
Statement 47 CFR Section 15.105(b)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device DTE4027 complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NO UNAUTHORIZED MODIFICATIONS
47 CFR Section 15.21
CAUTION: This equipment may not be modified, altered, or changed in any way
without signed written permission from BIO-RAD. Unauthorized modification may
void the equipment authorization from the FCC and will void the BIO-RAD warranty.
This device complies with FCC RF radiation exposure limits set forth for general
population (uncontrolled exposure). This device must be installed to provide a
separation distance of at least 20cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
DTE4027 RFID Reader Module
User Manual 4
WARNING TO USERS IN THE CANADA / ATTENTION POUR LES
UTILISATEURS AU CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
This device complies with Industry Canada RF radiation exposure limits set forth for
general population (uncontrolled exposure). This device must be installed to provide
a separation distance of at least 20cm from all persons and must not be collocated
or operating in conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes: (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif
doit être prêt a accepter tout brouillage radioélectrique reçu, même si ce brouillage
est susceptible de compromettre le fonctionnement du dispositif.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l’ intention d’autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à
l’établissement d’une communication satisfaisante.
Le présent appareil est conforme aux niveaux limites d’exigences d’exposition RF
aux personnes définies par Industrie Canada. Cet appareil doit être installé afin
d’offrir une distance de séparation d’au moins 20cm avec l’utilisateur, et ne doit pas
être installé à proximité ou être utilisé en conjonction avec une autre antenne ou un
autre émetteur.
DTE4027 RFID Reader Module
User Manual 5
MODULE INTEGRATION SPECIAL WARNINGS FOR US & CANADA
The DTE4027 module is considered as component that will be operated in
combination with the final equipment. Then, the final equipment (including
power supply system) still needs to re-confirm that the whole system complies
with both intentional and unintentional emission requirements.
We recommend that the minimum 20cm separation distance (for people &
antennas/transmitter) should be mentioned in the end product documentation.
The end product’s regulatory label should mention:
"Contains FCC ID: 2ABUUDTE4027 and IC: 11658A-DTE4027".
The motherboard of final equipment where DTE4027 module is to be integrated
must provide a power supply regulation to the module.
TRADEMARKS AND REFERENCES
All trademarks are the property of their respective companies.
DTE4027 RFID Reader Module
User Manual 6
1 INTRODUCTION
1.1 General Description
The Bio-Rad DTE4027 module is a complete read and write solution for 13.56 MHz Mifare Classic cards
(1k, 4k).
It is designed to be integrated in an equipment in order to add RFID feature with low engineering and
certification efforts.
2 SPECIFICATIONS
2.1 Physical Specifications
2.1.1 Dimensions
Width: 70 mm
Height: 40 mm
2.1.2 Weight
Board alone: 10 g
2.2 Technical Specifications
2.2.1 General Specifications
Power Input Requirements: 5VDC +/- 10 % regulated
Power Consumption: 150 mA maximum
Operating Environment
Temperature: -20 to + 50°C
Humidity: 20 - 80% non-condensing
Storage Conditions
Temperature: -40 to + 85°C
Humidity: 10 - 95%
Operating frequency: 13.56 MHz
Protocol: Mifare 13.56 MHz
Transmission range: 5 to 15 mm
Number of write cycles: >15,000
Communication protocol Compliant with ISO 14443A
Communication interface: UART, TTL levels
Data rate: 9600 bps, 8 bits, 1 stop, no parity
Maxim number of simultaneous
modules
1
48
1
Number of modules in the same host and being active together at the same time
DTE4027 RFID Reader Module
User Manual 7
3 SYSTEM DESCRIPTION
The hardware is a small PCB which has the following parts:
RFID antenna coil on the PCB
RFID chip
Slave PIC processor for interfacing between the UART commands and the RFID chip
Red and green LEDs that can be arbitrarily controlled via UART
Micro-switch that can be read via UART
On the back of the RFID board there is a push-button micro-switch that is connected to two spare inputs
on the slave processor (RA2 and RA3). This can be read via the UART communication.
3.1 Electrical Interface
The RFID connector is a 6-pin Molex PicoFlex 90814-0006.
Pin Function
1 5V
2 Ground
3 Data out of master to RFID
4 Data out of RFID to master
5 RFID CTS to master
6 Not connected
3.2 Block Diagram
13M560Hz
µC
PIC16F87-I/SS
13M560Hz
RFID IC
MFRC5310
1T/OEF
Adaptation
circuitry
UART
SPI
5V
5V
5V
Antenna
DTE4027 RFID Reader Module
User Manual 8
3.3 Mechanical Drawing
77 mm
Antenna
Centre
27.5 mm
27.5 mm
56.5 mm
LED
5.1 mm
1.6 mm
3.5 mm
3.0 mm
SW
With its plastic enclosure:
DTE4027 RFID Reader Module
User Manual 9
4 INSTALLATION PROCEDURE
4.1 Installation Requirements
In order to reduce unwanted emission in the spurious domain under the maximum regulatory limits, two
ferrites must be added on the cable connecting the RFID board to the instrument at a distance of 70 mm
maximum from the RFID board connector. The ferrites are mounted as described:
One ferrite on the power supply wires
One ferrite on the data and switch wires
Wires must make a loop one time through the ferrite
Ferrites must be Würth Elektronik P/N 7427114
4.2 Installation
Install the board with screws using the four holes. The PCB should be covered by an RF permissive
material cover (e.g. plastic).
Power the board with a regulated 5 VDC power supply.
4.3 Command set
The command set is described in the MFPROT_LP.pdf document that can be downloaded from
http://www.ibtechnology.co.uk/pdf/MFprot_LP.PDF. Please refer to this document to control the board.
5 TROUBLESHOOTING
5.1 Error Messages
Error Message
Probable Cause(s)
LED doesn’t light up
Check the presence of 5VDC between pin 1 and 2 of the
connector
The board doesn’t respond to UART Check the host baud rate
RFID Tag cannot be red Check the tag type and distance to the reader
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

BIO RAD DTE41027 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues