Ryobi RY3716 Le manuel du propriétaire

Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the

unit and void your warranty. Only use unleaded gasoline containing up to 10% ethanol.

Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une telle utilisation représente une

violation de la loi fédérale et endommagera l’appareil et annulera la garantie. Utiliser seulement de l’essence sans plomb ne

contenant pas plus de 10 % d’éthanol.

No utilice combustibles E15 o E85 con este producto. Esto constituye una violación a la ley federal, dañará la unidad y anulará

la garantía. Utilice únicamente gasolina sin plomo que contiene hasta 10% de etanol.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

RY3714 / 14 in. 37cc Chain Saw

Scie à chaîne de 37 cc de 35 cm (14 po)

Motosierra de 35 cm (14 pulg.), 37 cc

RY3716 / 16 in. 37cc Chain Saw

Scie à chaîne de 37 cc de 40 cm (16 po)

Motosierra de 40 cm (16 pulg.), 37 cc

NOTICE AVIS AVISO

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 General Safety Rules ...................... 2-3

 Specific Safety Rules ...................... 3-4

 Symbols .......................................... 5-6

 Glossary of Terms ...............................7

 Features .......................................... 8-9

 Assembly ...................................... 9-10

 Operation .................................... 10-23

 Maintenance ............................... 24-37

 Bar and Chain Combinations ............ 37

 Troubleshooting .......................... 38-39

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE DES MATIÈRES

 Règles de sécurité générales .......... 2-3

 Règles de sécurité particulières ...... 4-5

 Symboles ........................................ 5-6

 Glossaire .............................................7

 Caractéristiques .............................. 8-9

 Assemblage .................................. 9-10

 Utilisation .................................... 10-24

 Entretien ...................................... 24-38

 Combinaisons de guide et chaîne ....38

 Dépannage .................................. 39-40

 Commande de pièces/

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

ÍNDICE DE CONTENIDO

 Reglas de seguridad generales ...... 2-3

 Reglas de seguridad específicas .... 4-5

 Símbolos ......................................... 5-6

 Glosario de términos ........................... 7

 Características ................................ 8-9

 Armado ......................................... 9-10

 Funcionamiento .......................... 10-24

 Mantenimiento ............................ 24-39

 Combinaciones de barra y cadena ...39

 Corrección de problemas ........... 40-42

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

Page 2 — English

WARNING:

Read and understand all instructions. Failure

to follow all instructions listed below, may result

in electric shock, fire and/or serious personal

injury.

READ ALL INSTRUCTIONS

Know your tool. Read the operator’s manual

carefully. Learn the saw’s applications and lim-

itations as well as the specific potential hazards

related to this tool.

■ Kickback may occur when the nose or tip of

the guide bar touches an object, or when the

wood closes in and pinches the saw chain in

the cut. Tip contact in some cases may cause a

lightning-fast reverse reaction, kicking the guide

bar up and back toward the operator. Pinching

the saw chain along the top of the guide bar

may push the guide bar rapidly back toward the

operator. Either of these reactions may cause

you to lose control of the saw, which could result

in serious personal injury. Do not rely exclusively

upon the safety devices built into the saw. As a

chain saw user, you should take several steps

to keep your cutting jobs free from accident or

injury.

• With a basic understanding of kickback,

you can reduce or eliminate the element

of surprise. Sudden surprise contributes to

accidents.

• Keep a good firm grip on the saw with both

hands when the engine is running. Place your

right hand on the rear handle and your left

hand on the front handle with your thumbs

and fingers encircling the chain saw handles.

A firm grip together with a stiff left arm will

help you maintain control of the saw if kick-

back occurs.

• Make sure that the area in which you are

cutting is free from obstructions. DO NOT

let the nose of the guide bar contact a log,

branch, fence, or any other obstruction that

could be hit while you are operating the saw.

• Cut at high engine speeds. Always cut

with the engine running at full speed. Fully

squeeze the throttle trigger and maintain a

steady cutting speed.

• Do not overreach or cut above chest height.

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

• Only use replacement bars and chains spec-

ified by the manufacturer or the equivalent.

Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, bystand-

ers, or any combination of these persons may

result from one-handed operation. A chain saw

is intended for two-handed use.

Do not operate a chain saw when you are

fatigued. Fatigue causes carelessness. Never

operate a chain saw when you are tired or under

the influence of medication, drugs, or alcohol.

 Stay alert - Watch what you are doing and use

common sense when operating a chain saw. A

moment of inattention while operating the chain

saw may result in death or serious personal

injury.

 Chain saw work can be strenuous. If you have

a medical condition that may be aggravated or

a disability that may prevent you from safely

operating and controlling the chain saw, check

with your doctor before using the chain saw.

Use safety footwear. Wear snug-fitting cloth-

ing, protective gloves, and eye, hearing, and

head protection devices.

 Heavy protective clothing may increase oper-

ator fatigue, which could lead to heat stroke.

During weather that is hot and humid, heavy

work should be scheduled for early morning

or late afternoon hours when temperatures are

cooler.

Do not stand on any unstable surface while

using the chain saw, such as ladders, scaffolds,

trees, etc.

Use caution when handling fuel. Move the

chain saw at least 30 feet from the fueling point

before starting the engine.

Do not allow other persons to be near the

chain saw when starting or cutting with the

chain saw. Keep bystanders and animals out

of the work area.

Do not start cutting until you have a clear

work area, secure footing, and a planned retreat

path from the falling tree.

GENERAL SAFETY RULES

Page 3 — English

WARNING:

The warnings, labels, and instructions found

in this section of the operator’s manual are for

your safety. Failure to follow all instructions may

result in serious personal injury.

Do not cut vines and/or small underbrush (a

diameter of less than 3 in.).

Muffler surfaces are very hot during and after

operation of the chain saw; keep all body parts

away from the muffler. Serious burns may occur

if contact is made with the muffler.

■Always hold the chain saw with both hands

when the engine is running. Use a firm grip

with thumbs and fingers encircling the chain

saw handles.

Keep all parts of your body away from the

saw chain when the engine is running.

Always carry the chain saw with the engine

stopped and the brake engaged, the guide bar

and saw chain to the rear, and the muffler away

from your body. When transporting the chain

saw, use the appropriate guide bar scabbard.

Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and

securely assembled. Be sure that the saw chain

stops moving when the throttle control trigger

is released.

■Shut off the engine before setting the chain

saw down. Do not leave the engine running

unattended. As an additional safety precaution,

apply the chain brake prior to setting down the

saw.

■Use extreme caution when cutting small-size

brush and saplings because slender material

may catch the saw chain and be whipped

toward you or pull you off balance.

■When cutting a limb that is under tension,

be alert for springback so that you will not be

struck when the tension in the wood fibers is

released.

■Keep the handles dry, clean, and free of oil or

fuel mixture.

Do not start or operate the engine in a con-

fined space, building, near open windows,

or in other unventilated space where dan-

gerous carbon monoxide fumes can collect.

Carbon monoxide, a colorless, odorless,

and extremely dangerous gas, can cause

unconsciousness or death.

■Do not operate a chain saw in a tree unless

you have been specifically trained to do so.

Do not cut from a ladder, rooftop, or other

unstable support; this is extremely dangerous.

All chain saw service, other than the items

listed in the instruction manual and all main-

tenance, should be performed by competent

chain saw service personnel. (For example, if

improper tools are used to remove the flywheel

or if an improper tool is used to hold the flywheel

in order to remove the clutch, structural damage

to the flywheel could occur and subsequently

could cause the flywheel to burst.)

Always have a fire extinguisher available

when using chain saw.

Use only the replacement guide bars and low

kickback chains specified for the saw.

■Do not adapt the powerhead to a bow guide

or use it to power any attachments or devices

not listed for the saw.

■The gas powered saw is classified by CSA

262.1-15 as a Class 1C saw. It is intended for

infrequent use by homeowners, cottagers, and

campers, and for such general applications as

clearing, pruning, cutting firewood, etc. It is not

intended for prolonged use. Prolonged periods

of operation can cause circulatory problems in

the user’s hands due to vibration.

Save these instructions. Refer to them

frequently and use to instruct other users. If

you loan someone this tool, loan them these

instructions also.

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

Page 4 — English

SPECIFIC SAFETY RULES

■Never let anyone use the chain saw who

has not received adequate instructions in its

proper use. This applies to rentals as well as

privately owned saws.

■Before you start the engine, make sure the

saw chain is not contacting any object.

Wear snug-fitting clothing. Always wear heavy

long pants, boots, and gloves. Do not wear

jewelry, short pants, sandals, or go barefoot.

Do not wear loose fitting clothing, which could

be drawn into the engine or catch the chain

or underbrush. Wear overalls, jeans, or chaps

made of cut-resistant material or ones that

contain cut-resistant inserts. Secure hair so that

it is above shoulder level.

■Wear non-slip safety footwear and heavy-

duty gloves to improve your grip and to protect

your hands.

■Wear eye protection with side shields marked

to comply with ANSI Z87.1, along with hear-

ing and head protection, when operating this

equipment.

Keep bystanders and animals out of the work

area. Do not allow other persons to be nearby

during starting or cutting with the chain saw.

NOTE: The size of the work area depends on the

job being performed as well as the size tree or

workpiece involved. For example, felling a tree

requires a larger work area than making other

cuts (i.e., bucking cuts, etc.).

Keep SAFE-T-TIP

™

anti-kickback nose guard

properly mounted on the guide bar to prevent

rotational kickback.

Follow the sharpening and maintenance

instructions for the saw chain.

Never operate a chain saw that is damaged,

improperly adjusted, or is not completely

and securely assembled. Be sure that the saw

chain stops moving when the throttle control

trigger is released. If the saw chain moves at

idle speed, the carburetor may need adjusting.

Refer to Adjusting the Carburetor in the Main-

tenance section of this manual. If the saw chain

still moves at idle speed after adjustment has

been made, contact a qualified service center

for adjustment and discontinue use until the

repair is made.

■This product is intended for infrequent use

by homeowners and other occasional users

for general applications such as clearing, prun-

ing, cutting firewood, etc. It is not intended for

prolonged use. Prolonged periods of operation

can cause circulatory problems in the user’s

hands due to vibration. For such use, it may be

appropriate to use a product having an anti-

vibration feature.

REFUELING (DO NOT SMOKE!)

■To reduce the risk of fire and burn injury,

handle fuel with care. It is highly flammable.

■Mix and store fuel in a container approved for

gasoline.

■Mix fuel outdoors where there are no sparks

or flames.

■Select bare ground, stop the engine, and

allow it to cool before refueling.

■Loosen the fuel cap slowly to release pressure

and to keep fuel from escaping around the cap.

■Tighten the fuel cap securely after refueling.

■Wipe spilled fuel from the unit. Move 30 feet

away from refueling site before starting engine.

Never attempt to burn off spilled fuel under

any circumstances.

KICKBACK

Kickback is a dangerous reaction that can

lead to serious injury. Do not rely only on the

safety devices provided with the saw. As a

chain saw user, you must take special safety

precautions to help keep your cutting jobs free

from accident or injury. See the General Safety

Rules and Operation sections of this manual

for added information on kickback and how to

avoid serious personal injury.

SAVE THESE INSTRUCTIONS

Page 5 — English

Some of the following symbols may be used on this tool. Please study them and learn their meaning.

Proper interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Precautions that involve your safety.

Read The Operator’s

Manual

To reduce the risk of injury, user must read and

understand operator’s manual before using this product.

Wear Eye, Hearing, and

Head Protection

Wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing and head

protection when operating this equipment.

Keep Tool Away from

Electrical Lines/Keep

Bystanders Away

DANGER! Risk of electrocution! Keep tool 50 feet away

from electrical lines. Keep all bystanders at least 50 ft.

away or twice the height of the largest trees in the felling

area when felling.

SAFE-T-TIP

™

Nose Guard

The SAFE-T-TIP

™

nose guard on the guide bar helps

prevent kickback.

Operate With Two Hands Hold and operate the saw properly with both hands.

One Handed Do not operate the saw using only one hand.

Bar Nose Contact

Avoid bar nose contact. Tip contact may cause the

guide bar to move suddenly upward and backward,

which may cause serious injury.

The following signal words and meanings are intended to explain the levels of risk associated with

this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION

Indicates a hazardous situation, that, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered

important, but not related to a potential injury (e.g. messages

relating to property damage).

SYMBOLS

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning.

Proper interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Hot Surface

To reduce the risk of injury or damage, avoid contact

with any hot surface.

Kickback DANGER! BEWARE OF KICKBACK.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling the chain saw.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

No Smoking No smoking, sparks, or open flame.

Carbon Monoxide

Engines produce carbon monoxide which is an

odorless, deadly poison. Do not operate in an

enclosed area.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use

with an octane rating of 87 [(R + M)/2] or higher. This

product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant.

Page 7 — English

Automatic Oiler System

Lubrication is provided by the automatic oiler

system. The oiler is driven by the sprocket and

adds lubrication only when the chain is moving.

Bucking

The process of cross cutting a felled tree or log

into lengths.

Chain Brake

A device used to stop the saw chain.

Chain Saw Powerhead

A chain saw without the saw chain and guide bar.

Clutch

A mechanism for connecting and disconnecting

a driven member to and from a rotating source of

power.

Drive Sprocket or Sprocket

The toothed part that drives the saw chain.

Felling

The process of cutting down a tree.

Felling Back Cut

The final cut in a tree felling operation made on

the opposite side of the tree from the notching

undercut.

Front Handle

The support handle located at or toward the front

of the chain saw. This handle is for the left hand.

Front Handle Guard

A structural barrier between the front handle of

a chain saw and the guide bar, typically located

close to the hand position on the front handle, and

sometimes employed as an activating lever for a

chain brake.

Guide Bar

A solid railed structure that supports and guides

the saw chain.

Kickback

The backward or upward motion, or both, of the

guide bar occurring when the saw chain near the

nose of the top area of the guide bar contacts any

object such as a log or branch, or when the wood

closes in and pinches the saw chain in the cut.

Kickback (Pinch)

The rapid pushback of the saw which can occur

when the wood closes in and pinches the moving

saw chain in the cut along the top of the guide bar.

Kickback (Rotational)

The rapid upward and backward motion of the

saw which can occur when the moving saw chain

near the upper portion of the tip of the guide bar

contacts an object, such as a log or branch.

Low-Kickback Chain

A low kickback saw chain is a chain that has met

the kickback performance requirements of ANSI/

OPEI B175.1-2012 when tested according to the

provisions specified in ANSI/OPEI B175.1-2012.

Normal Cutting Position

Those positions assumed in performing the bucking

and felling cuts.

Notching Undercut

A notch cut in a tree that directs the tree’s fall.

Rear Handle

The support handle located at or toward the rear

of the saw. It normally contains the throttle. This

handle is for the right hand.

Reduced Kickback Guide Bar

A guide bar which has been demonstrated to

reduce kickback significantly.

Replacement Saw Chain

A chain that complies with the kickback perfor-

mance requirements of ANSI B175.1 when tested

with specific chain saws.

SAFE-T-TIP

™

Anti-Kickback Nose Guard

An attachment that may be provided on the end

of the guide bar to prevent the chain at the end of

the guide bar from contacting the wood.

Saw Chain

A loop of chain having cutting teeth that cut the

wood, and that is driven by the sprocket and is

supported by the guide bar.

Springpole

A small tree (sapling) or limb that is bent or trapped

under tension. It may “spring back” rapidly when

cut, causing a dangerous situation.

GLOSSARY OF TERMS

Page 8 — English

PRODUCT SPECIFICATIONS

Bar length:

RY3714 ....................................................14 in.

RY3716 ....................................................16 in.

Chain pitch .................................................3/8 in.

Chain gauge ............................................ .050 in.

Chain type ........................Low Profile Skip Tooth

Fig. 1

PRIMER

BULB

CHAIN BRAKE /

FRONT HAND

GUARD

FRONT

HANDLE

CYLINDER

COVER

SAFE-T-TIP

™

ANTI-KICKBACK

NOSE GUARD

CHOKE KNOB

BAR

MOUNTING NUTS

CLUTCH COVER

GUIDE BAR

REAR

HANDLE

THROTTLE

TRIGGER

ON/STOP

SWITCH

FUEL CAP

STARTER/FAN

HOUSING

STARTER GRIP

AND ROPE

TRIGGER

RELEASE

CHAIN OIL

CAP

LOW KICKBACK

SAW CHAIN

FEATURES

Chain drive links:

RY3714 .........................................................52

RY3716 .........................................................56

Drive sprocket ..........................................6-tooth

Engine displacement .................................... 37cc

Idle engine speed .........2,700 ± 200 r/min. (RPM)

Fuel tank capacity ...................................10.4 oz.

Chain lubricant tank capacity ....................7.1 oz.

STOP

MUFFLER

Page 9 — English

 Do not discard the packing material until you

have carefully inspected and satisfactorily

operated the tool.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Chain Saw

Scabbard

Combination Wrench

2-Cycle Engine Lubricant

Operator’s Manual

Case (RY3716 only)

KNOW YOUR CHAIN SAW

See Figure 1.

The safe use of this product requires an under-

standing of the information on the tool and in

this operator’s manual as well as a knowledge

of the project you are attempting. Before use of

this product, familiarize yourself with all operating

features and safety rules.

CHOKE KNOB

The choke knob opens and closes the choke valve

in the carburetor. Positions available include FULL

CHOKE, HALF CHOKE, and RUN.

COMBINATION WRENCH

A combination wrench tool is provided for use

when performing various maintenance procedures.

CHAIN BRAKE / FRONT HAND GUARD

The chain brake is designed to quickly stop the

chain from rotating. When the chain brake / front

hand guard is pushed toward the bar, the chain

should stop immediately. The chain brake does

not prevent kickback.

GUIDE BAR

The factory-equipped guide bar has a small radius

tip that offers somewhat lower kickback potential.

LOW KICKBACK SAW CHAIN

The low kickback saw chain helps minimize the

force of a kickback reaction by preventing the

cutters from digging in too deeply at the kickback

zone.

PRIMER BULB

The primer bulb pumps fuel from the fuel tank to

the car buretor.

SAFE-T-TIP

™

ANTI-KICKBACK NOSE

GUARD

The SAFE-T-TIP

™

Anti-Kickback Nose Guard is an

attachment provided on the end of the guide bar

to prevent the chain on the end of the guide bar

from contacting the wood.

THROTTLE TRIGGER

The throttle trigger is used for starting the chain

saw, and also for controlling chain rotation.

UNPACKING

This product has been shipped completely

assembled.

 Carefully remove the tool and any accessories

from the box. Make sure that all items listed in

the packing list are included.

WARNING:

Do not use this product if it is not completely

assembled or if any parts appear to be missing

or damaged. Use of a product that is not prop-

erly and completely assembled could result in

serious personal injury.

 Inspect the tool carefully to make sure no break-

age or damage occurred during shipping.

FEATURES

ASSEMBLY

Page 10 — English

WARNING:

Do not attempt to modify this tool or create

accessories not recommended for use with

this tool. Any such alteration or modification is

misuse and could result in a hazardous condi-

tion leading to possible serious personal injury.

NOTE: The chain saw has been fully factory tested.

It is normal to find some slight lubricant residue

on the saw. Read and remove all hang tags and

store with the Operator’s Manual.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing and head protection. Failure to do so

could result in objects being thrown into your

eyes and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool.

The use of attachments or accessories not rec-

ommended can result in serious personal injury.

WARNING:

This product is equipped with a spark arrestor

that has been evaluated by the USDA Forest

Service; however, product users must comply

with Federal, State, and local fire prevention

regulations. Check with appropriate authori-

ties. Contact customer service or a qualified

service center to purchase a replacement spark

arrestor.

DANGER:

Never cut near power lines, electric cords, or

other electric sources. If bar and chain jams

on any electrical cord or line, DO NOT TOUCH

THE BAR OR CHAIN! THEY CAN BECOME

ELECTRICALLY LIVE AND VERY DANGEROUS.

Continue to hold the chain saw by the insulated

rear handle or lay it down and away from you in

a safe manner. Disconnect the electrical service

to the damaged line or cord before attempting

to free the bar and chain from the line or cord.

Contact with the bar, chain, other conductive

parts of the chain saw, or live electric cords or

lines will result in death by electrocution, electric

shock, or serious personal injury.

WARNING:

Do not allow familiarity with tools to make you

careless. Remember that a careless fraction of

a second is sufficient to inflict serious injury.

WARNING:

Muffler surfaces are very hot during and after

operation of the chain saw; keep all body parts

away from the muffler. Serious burns can occur

if contact is made with the muffler.

WARNING:

If any parts are damaged or missing do not

operate this tool until the parts are replaced.

Failure to heed this warning could result in

serious personal injury.

ASSEMBLY

OPERATION

Page 11 — English

ETHANOL BLENDED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It

is a violation of federal law and will damage

the unit and void your warranty. Only use

unleaded gasoline containing up to 10%

ethanol.

NOTE: To improve performance when using

ethanol-blended fuels, we recommend the use of

Ethanol Shield 2-cycle lubricant.

MIXING THE FUEL

This product is powered by a 2-cycle engine and

requires pre-mixing gasoline and 2-cycle lubricant.

Pre-mix unleaded gasoline and 2-cycle engine

lubricant in a clean container approved for gaso-

line. DO NOT mix quantities larger than usable in

a 30-day period.

Recommended fuel: This engine is certified to

operate on unleaded gasoline intended for auto-

motive use.

NOTE: We recommend you use Ethanol Shield

2-cycle lubricant or an equivalent high-quality

synthetic 2-cycle lubricant in this product. Mix at

2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT (50:1)

GASOLINE LUBRICANT

1 Gallon (US) 2.6 oz.

1 Liter 20 cc (20 ml)

FILLING THE FUEL TANK

See Figure 2.

WARNING:

Gasoline and its vapors are highly flammable

and explosive. To prevent serious personal

injury and property damage, handle it with care.

Keep away from ignition sources and open

flames, handle outdoors only, do not smoke,

and wipe up spills immediately.

Clean the surface around the fuel cap to prevent

contamination.

Loosen the fuel cap slowly.

WARNING:

Never fell a tree or cut a log or limb that has a

diameter greater that the length of the guide

bar. Only properly trained professionals should

perform these cuts. Performing these types of

cuts can cause an accident and result in death

or serious personal injury.

NOTICE:

Before each use, inspect the entire product

for damaged, missing, or loose parts such as

screws, nuts, bolts, caps, etc. Tighten securely

all fasteners and caps and do not operate this

product until all missing or damaged parts are

replaced. Please contact customer service or a

qualified service center for assistance.

APPLICATIONS

You may use this tool for the purposes listed below:

Basic limbing, felling, and woodcutting

FUEL AND REFUELING

HANDLING THE FUEL SAFELY

WARNING:

Check for fuel leaks. A leaking fuel cap, tank,

or line is a fire hazard and must be replaced

immediately. If you find any leaks, correct the

problem before using the product. Failure to do

so could result in a fire that could cause serious

personal injury.

Always handle fuel with care; it is highly

flammable.

Always refuel outdoors and do not inhale fuel

vapors.

Do not let gasoline or lubricant come in contact

with skin.

Keep gasoline and lubricant away from the eyes.

If gasoline or lubricant comes in contact with

the eyes, wash them immediately with clean

water. If irritation is still present, see a doctor

immediately.

Clean up spilled fuel immediately.

Refer to Refueling in the Specific Safety Rules sec-

tion of this manual for additional safety information.

OPERATION

Page 12 — English

INCREASE

Carefully pour the fuel mixture into the tank.

Avoid spillage.

Prior to replacing the fuel cap, clean and inspect

the o-ring.

Immediately replace the fuel cap and hand

tighten. Wipe up any fuel spillage.

NOTE: It is normal for the engine to emit smoke

during and after the first use.

WARNING:

Always shut off engine before fueling. Never

remove fuel cap or add fuel to a machine with

a running or hot engine. Make sure unit is sit-

ting on a flat, level surface and only add fuel

outdoors. If the engine is hot, allow to cool for

at least five minutes before adding fuel. Imme-

diately replace fuel cap after fueling and tighten

securely. Move at least 30 ft. from refueling site

before starting the engine. Do not smoke and

stay away from open flames and sparks. Failure

to follow these instructions could result in a fire

and cause serious personal injury.

BAR AND CHAIN LUBRICATION

See Figure 3.

The bar and chain require continuous lubrication.

Lubrication is provided by the automatic oiler

system when the oil tank is kept filled. Lack of

lubricant will quickly ruin the bar and chain. Too

little lubricant will cause overheating shown by

smoke coming from the chain and/or discolor-

ation of the bar. Lubrication can be increased or

decreased by turning (up to 1/4 turn maximum)

the adjustment screw located on the bottom of

the crankcase with the screwdriver end of the

included combination wrench.

WARNING:

NEVER adjust the automatic oiler system when

the engine is running. Failure to do so could

cause serious personal injury.

ADDING BAR AND CHAIN LUBRICANT

See Figure 3.

Use a bar and chain lubricant designed for lubri-

cating chain saw chains. They are formulated to

extend bar and chain life by protecting against

wear and reducing friction and heat. Chain saw

Fig. 2

Fig. 3

OPERATION

should use approximately one tank of lubricant

per tank of fuel.

NOTE: Do not use dirty, used, or otherwise con-

taminated lubricants. Damage may occur to the

oil pump, bar, or chain.

Carefully pour the bar and chain lubricant into

the oil tank.

Fill the oil tank every time you fuel the engine.

ADJUSTMENT

SCREW

SCREWDRIVER

DECREASE

Page 13 — English

STOP

OPERATING THE CHAIN BRAKE

See Figures 4 - 5.

Check the operating condition of the chain brake

prior to each use.

Using the back of your left hand, engage the

chain brake by pushing the chain brake lever/

hand guard toward the bar while the chain is

rotating rapidly.

Reset the chain brake back into the RUN posi-

tion by grasping the top of the chain brake lever/

hand guard and pulling toward the front handle

until you hear a click.

WARNING:

If the chain brake does not stop the chain imme-

diately, or if the chain brake will not stay in the

run position without assistance, take the saw to

a qualified service center for repair prior to use.

NOTICE:

Before each use, check to make sure that

the chain is properly tensioned. A cold chain

is correctly tensioned when there is no slack

on the underside of the guide bar, the chain

is snug, and it can be turned by hand without

binding. During normal saw operation, the tem-

perature of the chain increases. The drive links

of a correctly tensioned warm chain will hang

approximately .050 in. out of the bar groove.

See the Adjusting the Chain Tension instruc-

tions in the Maintenance section of this manual

to properly adjust the chain tension.

STARTING THE ENGINE

See Figures 6 - 10.

The starting method differs depending on whether

the engine is cold or warm.

WARNING:

Keep your body to the left of the chain line.

Never straddle the saw or chain, or lean over

past the chain line.

Place the chain saw on level ground and ensure

that no objects or obstructions are in the imme-

diate vicinity that could come in contact with the

ON/STOP SWITCH

IN THE RUN

POSITION

Fig. 6

Fig. 7

Fig. 4

Fig. 5

RUN

POSITION

BRAKE

POSITION

OPERATION

RUN

POSITION

bar and chain. To prevent rapid dulling of the

chain, do not allow the bar and chain to contact

dirt on the ground.

Page 14 — English

Fig. 10

STARTER GRIP

AND ROPE

PRIMER BULB

Fig. 8

FULL CHOKE

POSITION

Fig. 9

RUN

HALF

CHOKE

FULL

CHOKE

 Hold the front handle firmly with your left hand

and put your right foot onto the base of the rear

handle.

To start a cold engine:

Set the on/stop switch to the RUN ( I ) position.

Make sure the chain brake is in the run position

by pulling back on the lever/hand guard.

Fully press and release the primer bulb 10 times.

Pull choke knob all the way out to FULL CHOKE

( ) position.

Pull the starter grip and rope until the engine

attempts to start, but no more than 5 times.

Push choke knob to HALF CHOKE ( ) posi-

tion.

Pull starter grip and rope until engine runs.

NOTE: Allow the saw to run in this posi-

tion 15–30 seconds, depending upon the

temperature.

Push the choke knob in to the RUN ( ) position.

NOTICE:

Failure to release partial throttle when chain

brake lever is in the brake position will result in

serious damage to the unit. Never squeeze and

hold the throttle trigger while the chain brake is

in the brake position.

To start a warm engine:

Set the on/stop switch to the RUN ( I ) position.

Make sure the chain brake is in the run position

by pulling back on the lever/hand guard.

Pull starter grip and rope until engine runs.

OPERATION

10X

Page 15 — English

STOP

STOPPING THE ENGINE

See Figures 11 - 12.

Release the throttle trigger and let the engine

return to idle. To stop the engine, move the on/

stop switch to the STOP ( ) position. Do not put

the chain saw on the ground when the chain is still

moving. For additional safety, set the chain brake

when the saw is not in use.

In the event that the on/stop switch will not stop the

saw, pull the choke knob out to the fully extended

position (FULL CHOKE / ) and engage chain

brake to stop the engine. If the on/stop switch will

not stop the saw when set to the STOP position,

have the on/stop switch repaired before using the

chain saw again to prevent unsafe conditions or

serious injury.

NOTE: When you are finished using the saw,

always relieve tank pressure by loosening, then

retightening, the chain oil and fuel mix caps. Allow

the engine to cool before storing.

ADJUSTING IDLE SPEED

See Figure 13.

WARNING:

The chain will move around the guide bar when

adjusting the idle speed. Wear all protective

clothing and keep all bystanders, children, and

pets at least 50 ft. away. Make adjustments

with the unit supported on a stable surface so

that the chain/guide bar does not contact the

ground or any object. Keep all parts of your

body away from the chain/guide bar and muf-

fler. Failure to follow these instructions could

result in serious personal injury.

If the engine starts, runs, and accelerates,

but will not idle, turn the idle speed screw “T”

clockwise to increase idle speed.

If the chain turns at idle, turn the idle speed

screw “T” counterclockwise to reduce the

idle RPM and stop the chain movement. If the

saw chain still moves at idle speed, contact

a qualified service center for adjustment and

discontinue use until the repair is made.

BRAKE POSITION

Fig. 12

Fig. 11

ON/STOP SWITCH IN

THE STOP POSITION

Fig. 13

IDLE SPEED

SCREW “T”

OPERATION

STOP

Page 16 — English

WARNING:

THE SAW CHAIN SHOULD NEVER TURN AT

IDLE. Turn the idle speed screw “T” counter-

clockwise to reduce the idle RPM and stop the

chain, or contact a qualified service center for

adjustment and discontinue use until the repair

is made. Serious personal injury may result from

the saw chain turning at idle.

PULL AND PUSH

See Figure 14.

The reaction force of the saw is always opposite to

the direction the chain is moving. Thus, the operator

must be ready to control the PULL when cutting

on the bottom edge of the bar and the PUSH when

cutting along the top edge.

NOTE: The chain saw has been fully factory tested.

It is normal to find some slight lubricant residue

on the saw.

WARNING:

KICKBACK occurs when the moving chain

contacts an object at the upper portion of the

tip of the guide bar or when the wood closes in

and pinches the saw chain in the cut. Contact

at the upper portion of the tip of the guide bar

can cause the chain to dig into the object and

stop the chain for an instant. The result is a

lightning-fast reverse reaction which kicks the

guide bar up and back toward the operator. If

the saw chain is pinched along the top of the

guide bar, the guide bar can be driven rapidly

back toward the operator. Either of these reac-

tions can cause loss of saw control, which can

result in serious injury.

Do not rely exclusively upon the safety devices

built into the saw. As a chain saw user, you

should take steps to keep your cutting jobs

free from accident or injury. See General Safety

Rules for more details.

PULL

PUSH

Fig. 14

OPERATION

Page 17 — English

KICKBACK PRECAUTIONS

See Figures 15 - 16.

Rotational kickback occurs when the moving chain

contacts an object at the Kickback Danger Zone of

the guide bar. The result is a lightning-fast reverse

reaction, which kicks the guide bar up and back

towards the operator. This reaction can cause loss

of control, which can result in serious injury.

PREPARING FOR CUTTING

PROPER GRIP ON HANDLES

See Figure 17.

See General Safety Rules for appropriate safety

equipment.

Wear non-slip gloves for maximum grip and

protection.

Hold the saw firmly with both hands. Always

keep your left hand on the front handle and your

right hand on the rear handle so that your body

is to the left of the chain line.

WARNING:

Never use a left-handed (cross-handed) grip or

any stance that would place your body or arm

across the chain line.

Maintain a proper grip on the saw whenever the

engine is running. The fingers should encircle

the handle and the thumb is wrapped under the

handlebar. This grip is least likely to be broken

by a kickback or other sudden reaction of the

saw. Any grip in which the thumb and fingers

are on the same side of the handle is dangerous

because a slight kick of the saw can cause loss

of control.

PROPER CUTTING STANCE

See Figure 18.

WARNING:

Always use the proper cutting stance described

in this section. Never kneel when using the

chain saw, except when felling a tree as illus-

trated in Figure 23. Kneeling could result in

loss of stability and control of the chain saw,

resulting in serious personal injury.

ROTATIONAL

KICKBACK

Fig. 16

KICKBACK

DANGER ZONE

Fig. 15

PROPER GRIP

Fig. 17

IMPROPER GRIP

PROPER HAND

GRIP POSITION

OPERATION

Page 18 — English

STRAIGHT

ARM

CHAIN LINE

THUMB ON

UNDERSIDE OF

HANDLE BAR

Fig. 18

Fig. 19

Balance your weight with both feet on solid

ground.

Keep left arm with elbow locked in a “straight

arm” position to withstand any kickback force.

Keep your body to the left of the chain line.

Keep your thumb on underside of handlebar.

OPERATION

WARNING:

DO NOT operate the throttle trigger with your

left hand and hold the front handle with your

right hand. Never allow any part of your body

to be in the chain line while operating a saw.

Improper operation of the chain saw could

result in serious personal injury.

CHAIN LINE

WORK AREA PRECAUTIONS

See Figure 19.

Cut only wood or materials made from wood;

no sheet metal, no plastics, no masonry, no

non-wood building materials.

Never allow children to operate the saw. Allow

no person to use this chain saw who has not

read this operator’s manual or received ade-

quate instructions for the safe and proper use

of this chain saw.

Keep everyone – helpers, bystanders, children,

and animals, a safe distance from the cutting

area. During felling operations, the safe dis-

tance should be a least twice the height of the

largest trees in the felling area. During bucking

operations, keep a minimum distance of 15 feet

between workers.

Always cut with both feet on solid ground to

prevent being pulled off balance.

Do not cut above chest height as a saw held

higher is difficult to control against kickback

forces.

Do not fell trees near electrical wires or build-

ings. Leave this operation for professionals.

Cut only when visibility and light are adequate

for you to see clearly.

BASIC OPERATING/CUTTING

PROCEDURES

Practice cutting a few small logs using the following

technique to get the “feel” of using the saw before

you begin a major sawing operation.

Take the proper stance in front of the wood with

the saw idling.

Accelerate the engine to full throttle just before

entering the cut by squeezing the throttle trigger.

Begin cutting with the saw against the log.

Keep the engine at full throttle the entire time

you are cutting.

Allow the chain to cut for you; exert only light

downward pressure. Forcing the cut could result

in damage to the bar, chain, or engine.

Page 19 — English

Release the throttle trigger as soon as the cut is

completed allowing the engine to idle. Running

the saw at full throttle without a cutting load can

result in unnecessary wear to the chain, bar, and

engine.

Do not put pressure on the saw at the end of

the cut.

FELLING TREES

HAZARDOUS CONDITIONS

See Figures 20 - 23.

WARNING:

Do not fell trees during periods of high wind or

heavy precipitation. Wait until the hazardous

weather has ended.

WARNING:

Closely check for broken or dead branches,

which could fall while cutting and do not cut

near buildings or electrical wires if you do not

know the direction of tree fall. Do not cut at

night or during bad weather conditions, such as

rain, snow, or strong winds, which can reduce

visibility and control of the chain saw. If the tree

you are felling makes contact with any utility

line, you should discontinue use of the chain

saw and immediately notify the utility company.

Failure to follow these instructions could result

in death or serious personal injury.

When felling a tree, it is very important that you

closely follow these warnings and instructions to

prevent possible death or serious personal injury.

■Do not cut down trees having an extreme lean

or large trees with rotten limbs, loose bark,

or hollow trunks. Have these trees pushed or

dragged down with heavy equipment, then cut

them up.

■Do not cut trees near electrical wires or build-

ings.

■Check the tree for damaged or dead branches

that could fall and hit you during felling.

■Periodically glance at the top of the tree during

the backcut to assure the tree is going to fall in

the desired direction.

Fig. 20

45°

PLANNED LINE

OF FALL

RETREAT PATH

OPERATION

If the tree starts to fall in the wrong direction,

or if the saw gets caught or hung up during the

fall, leave the saw and save yourself!



Felling a tree – When bucking and felling oper-

ations are being performed by two or more

persons, at the same time, the felling operation

should be separated from the bucking operation

by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a

manner that would endanger any person, strike

any utility line or cause any property damage. If

the tree does make contact with any utility line, the

utility company should be notified immediately.

 Before any cuts are started, pick your escape

route (or routes in case the intended route is

blocked); clear the immediate area around the

tree and make sure there are no obstructions in

your planned path of retreat. Clear paths of safe

retreat should extend back and diagonally (45°)

to the rear of the planned line of fall. When the

tree begins to fall, you should retreat away from

the direction of fall along a retreat path and at

least 20 feet away from the trunk in case it kicks

back over the stump. See Figure 20.

Page 20 — English

 Before felling is started, consider the force and

direction of the wind, the lean and balance of

the tree, and the location of large limbs. These

things influence the direction in which the tree

will fall. Do not try to fell a tree along a line

different from its natural line of fall.

 The chain saw operator should keep on the

uphill side of the terrain as the tree is likely to

roll or slide downhill after it is felled.

 Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where felling cuts are to

be made.

 Notched Undercut. Cut a notch about 1/3 the

diameter of the tree as shown in figure 21. Make

the cuts of the notch so they intersect at a right

angle to the line of fall. This notch should be

cleaned out to leave a straight line. To keep the

weight of the wood off the saw, always make

the lower cut of the notch before the upper cut.

See Figure 21.

 Felling Backcut. The backcut is always made

level and horizontal, and at a minimum of 2 in.

above the horizontal cut of the notch. See Figures

21 - 22.

 Never cut through to the notch. Always leave a

band of wood between the notch and backcut

(approximately 2 in. or 1/10 the diameter of the

tree). This is called “hinge” or “hingewood.” It

controls the fall of the tree and prevents slipping

or twisting or shoot-back of the tree off the

stump. See Figures 21 - 22.

 On large diameter trees, stop the back cut

before it is deep enough for the tree to either

fall or settle back on the stump. Then insert

soft wooden or plastic wedges into the cut so

they do not touch the chain. The wedges can

be driven in, little by little, to help jack the tree

over. See Figure 23.

NOTE: When bucking or felling with a wedge, it

may be necessary to remove the SAFE-T-TIP

™

anti-kickback nose guard to allow the bar to be

drawn through the cut. After the cut is complete,

the tip should be reinstalled immediately.



As tree starts to fall, stop the chain saw and put

it down immediately. Retreat along the cleared

path, but watch the action in case something

falls your way. Be alert for overhead limbs or

branches that may fall and watch your footing.

WEDGE

Fig. 23

HINGE

BACK CUT

Fig. 22

OPERATION

HINGE

2 in. (50 mm) OR 1/10 DIA

NOTCH -

APPROX. 1/3

DIAMETER OF

TRUNK

BACK CUT

2 in. (50 mm)

Fig. 21

WARNING:

Never cut through to the notch when making a

backcut. The hinge controls the fall of the tree,

this is the section of wood between the notch

and backcut.

La page charge ...

Ryobi RY3716 Le manuel du propriétaire

Ce manuel convient également à

Ryobi RY3716 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents