Troy-Bilt TB425CS Manuel utilisateur

Catégorie
Coupe-herbe
Taper
Manuel utilisateur

Ce manuel convient également à

Operator’s Manual
PART NO. 769-01892 (6/05)
TB425CS
&
TB475SS
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
4-Cycle Gas Trimmers
2
INTRODUCTION
Copy the serial number
here:
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator’s manual provides you with easy-to-
understand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition.
PRODUCT REFERENCES, ILLUSTRATIONS
AND SPECIFICATIONS
All information, illustrations, and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright© 2004 MTD SOUTHWEST INC, All Rights
Reserved.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
For service call 1-800-520-5520 to obtain a list of
authorized service dealers near you. For more details
about your unit, visit our website at www.troybilt.com.
DO NOT RETURN THE UNIT TO THE RETAILER.
PROOF OF PURCHASE WILL BE REQUIRED FOR
WARRANTY SERVICE.
Before beginning, locate the unit’s model plate. It lists
the model and serial numbers of your unit. Refer to the
sample plate below and copy the information for future
reference.
S/N :
ITEM :
MODEL :
Make sure you carefully read and understand this manual
before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE U.S.
PATENTS. OTHER PATENTS PENDING.
TABLE OF CONTENTS
Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2
Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7
Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8
Starting/Stopping Instructions . . . . . . . . . . . . . . . .10
Operating Instructions . . . . . . . . . . . . . . . . . . . . . .11
Maintenance and Repair Instructions . . . . . . . . . . .13
Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .21
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .22
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Warranty Information . . . . . . . . . . . . . . . . . . . . . . .26
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E26
Copy the model and parent
part number here:
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the
states of California, Maine, Oregon and Washington.
All U.S. Forest Land and the state of California (Public
Resources Codes 4442 and 4443), Oregon and
Washington require, by law that certain internal
combustion engines operated on forest brush and/or
grass-covered areas be equipped with a spark arrestor,
maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for
regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or
a fine. This unit is factory equipped with a spark
arrestor. If it requires replacement, ask your LOCAL
SERVICE DEALER to install the Accessory Part
#180890 Spark Arrestor Kit.
CALIFORNIA PROPOSITION 65 WARNING
WARNING
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
3
RULES FOR SAFE OPERATION
SYMBOL MEANING
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
SYMBOL MEANING
Failure to obey a
safety warning can
result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.
WARNING:
Failure to obey a
safety warning will
result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock and
personal injury.
DANGER:
Failure to obey a
safety warning may
result in property damage or personal injury
to yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock and personal injury.
CAUTION:
Indicates
danger,
warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.
SAFETY ALERT:
Read the Operator’s Manual(s) and follow all
warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
FOR QUESTIONS, CALL 1-800-520-5520
READ ALL INSTRUCTIONS
BEFORE OPERATING
Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
All guards and safety attachments must be installed
properly before operating the unit.
Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace parts that are cracked,
chipped, or damaged in any way. Do not operate the
unit with loose or damaged parts.
Carefully inspect the area before starting the unit.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
Be aware of the risk of injury to the head, hands and
feet.
Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders, and pets
outside a 50 feet (15 m.) radius; there still may be a
risk to bystanders from thrown objects. Bystanders
should be encouraged to wear eye protection. If you
are approached, stop the unit immediately.
Use only 0.095 inch,
2.41 mm diameter original
equipment manufacturer replacement line. Never use
metal-reinforced line, wire or rope. These can break
off and become dangerous projectiles.
Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
Store fuel only in containers specifically designed and
approved for the storage of such materials.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
When using the unit,
you must follow the
safety rules. Please read these instructions
before operating the unit in order to ensure
the safety of the operator and any bystanders.
Please keep these instructions for later use.
WARNING:
• IMPORTANT SAFETY INSTRUCTIONS •
Gasoline is highly
flammable, and its
vapors can explode if ignited. Take the
following precautions:
WARNING:
4
RULES FOR SAFE OPERATION
Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the fuel tank cap or
add fuel when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.
Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Remove the fuel cap
slowly, and only after the engine stops. Do not smoke
while fueling. Wipe up any spilled fuel from the unit
immediately.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke. Keep sparks and open flames away from the
area while adding fuel or operating the unit.
WHILE OPERATING
Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can be fatal.
Operate this unit only in a well-ventilated outdoor area.
Wear safety glasses or goggles that meet ANSI Z87.1
standards and are marked as such. Wear ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
Wear heavy long pants, boots, gloves and a long
sleeve shirt. Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair above
shoulder level.
The cutting attachment shield must always be in place
while operating the unit as a trimmer. Do not operate
unit without both trimming lines extended, and the
proper line installed. Do not extend the trimming line
beyond the length of the shield.
This unit has a clutch. The cutting attachment remains
stationary when the engine is idling. If it does not, have
the unit adjusted by an authorized service technician.
Adjust the handle to your size in order to provide the
best grip.
Be sure the cutting attachment is not in contact with
anything before starting the unit.
Use the unit only in daylight or good artificial light.
Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. Refer
to Starting/Stopping Instructions.
Use the right tool. Only use this tool for its intended
purpose.
Do not overreach. Always keep proper footing and
balance.
Always hold the unit with both hands when operating.
Keep a firm grip on both handles or grips.
Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it rotates.
Do not touch the engine, gear housing or muffler.
These parts get extremely hot from operation, even
after the unit is turned off.
Do not operate the engine faster than the speed
needed to cut, trim or edge. Do not run the engine at
high speed when not cutting.
Always stop the engine when cutting is delayed or
when walking from one cutting location to another.
If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
Stop the unit, switch the engine to off, and disconnect
the spark plug for maintenance or repair.
Use only original equipment manufacturer replacement
parts and accessories for this unit. These are available
from your authorized service dealer. Use of any
unauthorized parts or accessories could lead to
serious injury to the user, or damage to the unit, and
void your warranty.
Keep unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.
To reduce fire hazard, replace a faulty muffler and
spark arrestor. Keep the engine and muffler free from
grass, leaves, excessive grease or carbon build up.
OTHER SAFETY WARNINGS
Never store a fueled unit inside a building where fumes
may reach an open flame or spark.
Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
Store the unit in a dry area, locked up or up high to
prevent unauthorized use or damage, out of the reach
of children.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE
INSTRUCTIONS
5
RULES FOR SAFE OPERATION
SYMBOL MEANING
SAFETY ALERT SYMBOL
Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.
WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.
WEAR EYE AND HEARING
PROTECTION
WARNING: Thrown objects and
loud noise can cause severe eye
injury and hearing loss. Wear eye
protection meeting ANSI Z87.1-1989
standards and ear protection when
operating this unit.
Use a full face
shield when needed.
KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders,
especially children and pets, at least
50 feet (15 m.) from the operating area.
UNLEADED FUEL
Always use clean, fresh unleaded fuel.
THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
WARNING:Do not
operate without the cutting
attachment shield in place.
Keep away from the rotating cutting
attachment.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
ON/OFF STOP CONTROL
ON / START / RUN
ON/OFF STOP CONTROL
OFF or STOP
HOT SURFACE WARNING
Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.
OIL
Refer to operator's manual for the
proper type of oil.
6
KNOW YOUR UNIT
APPLICATIONS
As a trimmer:
Cutting grass and light weeds
Edging
Decorative trimming around trees, fences, etc.
Other optional accessories may be used with your unit.
Refer to Operating the EZ-Link System for a list of add-ons.
NOTE: The below illustration may differ slightly
from your unit. For example, the picture shows
a straight shaft. Your unit may have a curved
shaft.
Cutting Attachment
Shield
Fuel Cap
Throttle
Control
D-Handle
(TB475SS Only)
Cutting Attachment
Shaft Grip
Primer Bulb
Oil Fill Plug / Dipstick
Air Filter Cover
Spark Plug
Shaft Housing
Starter Rope Grip
EZ-Link™
Line Cutting Blade
Spark Plug
Muffler
Muffler Guard
Spark Arrestor
On/Off Stop Control
J-Handle
(TB425CS Only)
7
ASSEMBLY INSTRUCTIONS
For TB475SS only: ADJUST THE D-HANDLE
The TB475SS uses a D-handle only, which is pre-
installed on the unit. If you ever need to adjust it, make
sure it is at least 6 inches from the end of the shaft grip
(Fig. 1).
2. While holding the three pieces together, install the four
(4) screws through the top clamp and into middle clamp.
NOTE: The holes in the top and middle clamp will line up
only when assembled correctly.
3. Place the clamps and the J-handle over the shaft
housing and onto the bottom clamp.
4. Hold each hex nut in the bottom clamp recess with a
finger. Start screws with a large Phillips screwdriver.
Do not tighten until you make the handle adjustment.
5. Slide the J-handle in or out until the arrow/white line on
the decal touches the clamp assembly (Fig. 3). You must
first loosen the screws if the handle is pre-installed.
Fig. 2
Fig. 3
6. While holding the unit in the operating position
(Fig. 27), position the J-handle to the location that
provides you the best grip.
7. Tighten the clamp screws evenly, until the J-handle
is secure.
For TB425CS only: INSTALL AND ADJUST
THE J-HANDLE
1. Place the J-handle between the top and middle
clamp pieces (Fig. 2).
Decal
(4) Screws
Top Clamp
J-Handle
Middle Clamp
Bottom Clamp
Nuts
Shaft
Housing
Bottom Clamp
Shaft Grip
Minimum 6 inches
(15.24 cm)
Fig. 1
8
OIL AND FUEL INFORMATION
RECOMMENDED OIL TYPE
Using the proper type and weight of oil in
the crankcase is extremely important.
Check the oil before each use and change
the oil regularly. Failure to use the correct oil, or using
dirty oil, can cause premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American
Petroleum Institute) service class SF, SG, SH.
ADDING OIL TO CRANKCASE: INITIAL USE
NOTE: This unit is shipped without oil. In order to avoid
damage to the unit, put oil in the crankcase
before you attempt to start the unit.
Your unit is supplied with one 3.4 fluid oz. (100 ml.)
bottle of SAE 30 SF, SG, SH oil (Fig. 16).
NOTE: Save the bottle of oil. It can be used to measure
the correct amount during future oil changes.
See Changing the Oil.
1. Unscrew the top of the bottle of oil and remove the
paper seal covering the opening. Replace the top.
Next, cut the tip off the funnel spout (Fig. 16).
2. Place the unit on a flat level surface (Fig. 18).
3. Remove the oil plug / dipstick from the crankcase
(Fig. 17).
Fig. 16
Fig. 18
Oil Fill
NOTE: Never add oil to the fuel or fuel tank.
5. Wipe up any oil that may have spilled and reinstall
the oil fill plug / dipstick.
Check oil before each use and change as needed. Refer
to Changing the Oil.
Oil Fill Plug/Dipstick
Oil Fill Hole
Fig. 17
4. Pour the entire bottle of oil into the oil fill hole
(Fig. 18).
O-Ring
Funnel Spout
OVERFILLING OIL
CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY.
Check and maintain the proper oil level in
the crank case; it is important and cannot
be overemphasized. Check the oil before
each use and change it as needed. See
Changing the Oil.
WARNING:
9
OIL AND FUEL INFORMATION
FUELING THE UNIT
1. Remove the fuel cap (Fig. 19).
Fig. 19
Fuel Cap
Fuel Tank
Gas Can Spout
2. Place the gas container’s spout into the fill hole on
the fuel tank (Fig. 19) and fill the tank.
NOTE: Do not overfill the tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling
source and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to
Federal, State and Local regulations.
RECOMMENDED FUEL TYPE
Old fuel is the primary reason for improper unit
performance. Be sure to use fresh, clean, unleaded
gasoline.
NOTE: This is a four cycle engine. In order to avoid
damage to the unit, do not mix oil with
gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and
oxygenates such as ethanol, methanol or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate or form
acids when stored. Use fresh fuel (less than 60 days
old), when using alcohol-blended fuel.
Using Blended Fuels
If you choose to use a blended fuel, or its use is
unavoidable, follow recommended precautions:
Always use fresh unleaded gasoline
Use the fuel additive STA-BIL
®
or an equivalent
Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of fuel additives, such as STA-BIL
®
Gas
Stabilizer or an equivalent, will inhibit corrosion and
minimize the formation of gum deposits. Using a fuel
additive can keep fuel from forming harmful deposits in
the carburetor for up to six (6) months. Add 0.8 oz.
(23 ml.) of fuel additive per gallon of fuel according to the
instructions on the container. NEVER add fuel additives
directly to the unit's gas tank.
Unleaded
Gasoline
Add fuel in a clean,
well ventilated
outdoor area. Wipe up any spilled fuel
immediately. Avoid creating a source of
ignition for spilt fuel. Do not start the engine
until fuel vapors dissipate.
WARNING:
Gasoline is
extremely
flammable. Ignited Vapors may explode.
Always stop the engine and allow it to cool
before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING:
Remove fuel cap
slowly to avoid injury
from fuel spray. Never operate the unit
without the fuel cap securely in place
.
WARNING:
10
STARTING/STOPPING INSTRUCTIONS
STARTING INSTRUCTIONS
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control. Allow the
engine to cool down by idling.
2. Put the On/Off Stop Control in the OFF (O) position.
Start/On (I)
Stop/Off (O)
Throttle Control
Primer
Bulb
Starter Rope
Throttle Control
Cold Weather
Start Lever
(Fig. 23)
Cold
Weather
Start Lever
Run/ Open
Close/ Start
Fig. 20
Fig. 23
Fig. 22
Fig. 21
Operate this unit only in a
well- ventilated outdoor
area. Carbon monoxide exhaust fumes can be lethal in
a confined area.
WARNING:
Avoid accidental starting.
Make sure you are in the
starting position when pulling the starter rope
(Fig. 22).
To avoid serious injury, the operator and unit
must be in a stable position while starting.
Make sure that any Add-On item is installed correctly
and secure before starting the unit.
WARNING:
1. Check the oil level in the crankcase. Refer to
Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline.
Refer to Fueling the Unit.
NOTE: There is no need to turn the unit on. The On/Off
Stop Control is in the ON (I) position at all times
(Fig. 20).
IF COLD... For cold weather conditions (below 40°F),
flip the Cold Weather Start Lever (Fig. 23) down to the
start/closed position and continue to step 3. DO NOT
flip this lever down if the temperature is above 40°F.
3. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 21). If you can’t see
fuel in the bulb, press and release the bulb as many
times as it takes before you can see fuel in it.
4. With the unit in the starting position, do not squeeze
the throttle control (Fig. 22). Pull the starter rope out a
short distance, until you feel some resistance. This is
usually around 2-4 inches. Then pull the rope smoothly
and briskly. Repeat this 5 times. The engine should start
IF COLD... For cold weather conditions (below 40°F),
flip the Cold Weather Start Lever back up to the
run/open position.
5. Squeeze the throttle control to warm up the engine for
15 to 30 seconds. In cold weather, let the engine
warm up for 30 to 60 seconds.
IF... The engine does not start, go back to step 3.
IF
...
The engine stops while you are squeezing the
throttle, go back to step 4.
11
OPERATING INSTRUCTIONS
For edging (when using the line head cutting attachment
with EZ-Link™ models), lock the release button of the
cutting attachment into the 90° edging hole (Fig. 26).
OPERATING THE EZ-LINK
SYSTEM
The EZ-Link™ system enables the use of these optional
Add-Ons:
Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC
Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE
Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBAH
Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . TBSS
Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB
Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS
Brushcutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBBC*
*Do NOT use this attachment with an electric
powered unit.
Removing the Cutting Attachment or Add-On
1. Turn the knob counterclockwise to loosen (Fig. 24).
2. Press and hold the release button (Fig. 24).
3. While firmly holding the upper shaft housing, pull
the cutting attachment or add-on straight out of the
EZ-Link™ coupler (Fig. 25).
Installing the Cutting Attachment or Add-On
NOTE: Place the unit on the ground or on a work bench
to make add-on installation or removal easier.
1. Turn knob counterclockwise to loosen (Fig. 24).
Fig. 24
EZ-Link™ Coupler
Release Button
Guide Recess
Knob
Primary Hole
Upper Shaft Housing
EZ-Link™ Coupler
2. While firmly holding the add-on, push it straight into
the EZ-Link™ coupler (Fig. 25).
NOTE: Aligning the release button with the guide recess
will help installation (Fig. 24).
3. Turn the knob clockwise to tighten (Fig. 24).
Fig. 25
Fig. 26
Knob
Lower Shaft Housing
Release Button
90˚ Edging Hole
(Trimmer Only)
To avoid serious
personal injury and
damage to the unit, shut the unit off before
removing or installing add-ons.
WARNING:
Add-ons are to be
used in the primary
hole only. Using the wrong hole could lead to
personal injury or damage to the unit.
CAUTION:
Lock the release
button in the primary
hole and securely tighten the knob before
operating this unit.
CAUTION:
Before you begin
using any
attachment, read and understand the manual
that came with the attachment. Follow all
safety information contained within.
WARNING:
12
Fig. 29
OPERATING INSTRUCTIONS
HOLDING THE TRIMMER
Before operating the unit, stand in the operating position
(Fig. 27). Check for the following:
•T
he operator is wearing eye protection and proper clothing
With a slightly-bent right arm, the operator’s right hand
is holding the shaft grip
The operator’s left arm is straight, the left hand holding
the handle
The unit is at waist level
The cutting attachment is parallel to the ground and
easily contacts the grass without the need to bend over
Fig. 27
ADJUSTING TRIMMING LINE LENGTH
The Bump Head™ cutting attachment allows you to
release trimming line without stopping the engine. To
release more line, lightly tap the cutting attachment on the
ground (Fig. 28) while operating the trimmer at high speed.
NOTE: Always keep the trimming line fully extended.
Line release becomes more difficult as the cutting
line becomes shorter.
Each time the head is bumped, about 1 inch (25.4 mm) of
trimming line is released. A blade in the cutting
attachment shield will cut the line to the proper length if
excess line is released.
For best results, tap the Bump Head™ on bare ground or
hard soil. If line release is attempted in tall grass, the
engine may stall. Always keep the trimming line fully
extended. Line release becomes more difficult as the
cutting line becomes shorter.
NOTE: Do not rest the Bump Head™ on the ground
while the unit is running.
Fig. 28
Some line breakage will occur from:
Entanglement with foreign matter
Normal line fatigue
Attempting to cut thick, stalky weeds
Forcing the line into objects such as walls or fence posts
TIPS FOR BEST TRIMMING RESULTS
For best trimming results, operate unit at full throttle.
Keep the cutting attachment parallel to the ground.
Do not force the cutting attachment. Allow the tip of
the line to do the cutting, especially along walls.
Cutting with more than the tip will reduce cutting
efficiency and may overload the engine.
Cut grass over 8 inches (200 mm) by working from top
to bottom in small increments to avoid premature line
wear or engine drag.
Cut from right to left.
Slowly move the trimmer into and out of the cutting
area at the desired height. Move either in a forward-
backward or side-to-side motion. Cutting shorter
lengths produces the best results.
Trim only when grass and weeds are dry.
The life of your cutting line is dependent upon:
Proper adherence of explained trimming techniques
What vegetation is cut
Where vegetation is cut
For example, the line will wear faster when trimming against
a foundation wall as opposed to trimming around a tree.
DECORATIVE TRIMMING
Decorative trimming is accomplished by removing all
vegetation around trees, posts, fences and more.
Rotate the whole unit so that the cutting attachment is at
a 30° angle to the ground (Fig. 29).
Do not remove or alter
the line cutting blade
assembly. Excessive line length will make the
clutch overheat. This may lead to serious
personal injury or damage to the unit.
CAUTION:
Always wear eye,
hearing, foot and
body protection to reduce the risk of injury
when operating this unit.
WARNING:
13
MAINTENANCE AND REPAIR INSTRUCTIONS
To prevent serious
injury, never perform
maintenance or repairs with unit running.
Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
WARNING:
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures take your unit to any non-road
engine repair establishment, individual or
authorized service dealer.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may be
performed by any non-road engine repair
establishment, individual or authorized service dealer.
FREQUENCY MAINTENANCE REQUIRED REFER TO
Before starting engine
Fill fuel tank with fresh fuel
Check oil
Page 12
Page 21
Every 10 hours Clean and re-oil air filter Page 22
First change at 10 hours
Every 25 hours thereafter
Every 25 hours
Change oil
Change oil
Clean spark arrestor
Page 22
Page 22
Page 26
10 hours on new engine
Every 25 hours
Every 25 hours
Check rocker arm to valve clearance and adjust
Check rocker arm to valve clearance and adjust
Check spark plug condition and gap
Page 24
Page 24
Page 26
LINE INSTALLATION
Always use original equipment manufacturer 0.095 inch
(2.41 mm) replacement line. Lines other than those
specified may make the engine overheat or fail.
There are two methods to replace the SpeedSpool
®
trimming line:
• Wind the inner reel with new line
• Install a pre-wound inner reel
Winding the Inner Reel With New Line
NOTE: It Is unnecessary to remove the bump knob to
install a new trimming line.
1. Cut two pieces of 0.095 inch (2.41 mm) trimming
line, 10 feet (3 m) long.
2. Hold the outer spool and turn the inner reel
counterclockwise to line up the arrows on the outer
spool and inner reel (Fig. 41).
SPEEDSPOOL
®
(TB425CS & TB475SS)
Never use metal-
reinforced line, wire,
chain or rope. These can break off and
become dangerous projectiles.
WARNING:
Always use the
correct line length
when installing trimming line on the unit.
The line may not release properly if the line
is too long.
WARNING:
Top View Of The SpeedSpool
®
Outer Spool
Inner Reel
Fig. 41
Bump Knob
Arrows
3. Pull old line out of the line loading and line locking
holes (Fig. 42 and 43).
4. Insert a piece of trimming line straight into one of the
two eyelets in the outer spool. Push it up through the
line loading hole in the inner reel (Fig. 42). Do not
bend the line when inserting it into the eyelet.
14
MAINTENANCE AND REPAIR INSTRUCTIONS
Trimming Line
Line Loading Hole
Eyelet
Fig. 42
Line Locking Hole
5. Insert the line into the locking hole (Fig. 43). Do not
push the line more than a 1/2 inch (12.7 mm) into the
line locking hole. The line will form a small loop
(Fig. 43) when it is inserted correctly.
Fig. 43
6. Pull the line from the outer spool until the line is tight
against the inner reel (Fig. 44).
Fig. 44
Fig. 45
7. Repeat procedures 4-6 with the second piece of line.
8. Hold the outer spool. Wind the inner reel
counterclockwise until approximately four (4) inches
(102 mm) of line remain (Fig. 45).
NOTE: Do not wind the inner reel before installing the
second piece of line.
9. If winding the line becomes difficult or if the line
jams, pull the ends of the line from the spool
(Fig. 46). Continue winding the inner reel
counterclockwise until approximately 6 inches of line
is left.
Fig. 46
INSTALLING A PRE-WOUND REEL
1. Turn the bump knob counterclockwise and remove
the bump knob, spring and foam seal (Fig. 47).
Bump Knob
Foam Seal
Spring
Inner Reel
Fig. 47
2. Pull the old inner reel with existing line from the outer
spool.
3. Insert the ends of the prewound inner reel line into
the outer spool eyelets (Fig. 48). Push the new inner
reel, arrow side up, into the outer spool.
15
4. Remove any existing line from the inner reel before
cleaning. Remove any debris or grass from the knob,
spring, inner reel and foam seal. Wash the inner reel
with warm soapy water (Fig. 50).
Shaft
Plunger
NOTE: The inner reel must be totally dry before
reinstalling it into the outer spool. Do not lubricate
the inner reel or outer spool assembly.
6. Place the inner reel into the outer spool.
7. Place the bump knob, spring and foam seal into the
inner reel (Fig. 47).
8. Press the bump knob down and tighten clockwise.
9. Install new line as described in Line Installation for
the SpeedSpool
®
.
5. Clean the shaft and the inner surface of the outer
spool. To clean the shaft underneath the plunger,
press down on the plunger (Fig. 51). Remove any dirt
or debris from the shaft.
Fig. 51
Inner Reel
Fig. 50
Fig. 49
3. Pull the inner reel with existing line from the outer
spool (Fig. 48).
CLEANING THE SPEEDSPOOL
®
Cleaning the SpeedSpool
®
may be necessary if:
A jammed or excessive line must be removed
The SpeedSpool
®
becomes difficult to wind or does
not operate correctly when bumping the head on the
ground
1. Hold the outer spool, and unscrew the bump knob
counterclockwise (Fig. 49).
2. Pull out the bump knob, spring and foam seal (Fig. 47).
MAINTENANCE AND REPAIR INSTRUCTIONS
4. Hold the inner reel in place and install the bump
knob, spring and foam seal (Fig. 47). Press down
and turn the bump knob clockwise. Grasp the ends
and pull firmly to release the line from the holding
slots in the inner reel.
Releasing the Inner Reel
If the SpeedSpool
®
does not release line correctly, pull
the ends of the line firmly from the spool (Fig. 46). If this
does not the release line, follow the Cleaning the
SpeedSpool
®
instructions.
Fig. 48
16
MAINTENANCE AND REPAIR INSTRUCTIONS
CHECKING THE OIL LEVEL
The importance of checking and maintaining the proper
oil level in the crankcase cannot be overemphasized.
Check oil before each use:
1. Stop the engine and allow oil to drain into the crankcase.
2. Place the unit on a flat, level surface to get a proper
oil level reading.
3. Keep dirt, grass clippings and other debris out of the
engine. Clean the area around the oil fill plug/dipstick
before removing it.
4. Remove the oil fill plug/dipstick and wipe off oil.
Reinsert it all the way back in.
5. Remove the oil fill plug/dipstick and check the oil level.
Oil should be up to the top of the dipstick (Fig. 52).
6. If the level is low, add a small amount of oil to the oil
fill hole and recheck (Fig. 53). Repeat this procedure
until the oil level reaches the top of the dipstick.
NOTE: Do not overfill the unit.
Top of Dipstick
O-Ring
Oil Fill Plug/Dipstick
Fig. 52
Fig. 53
NOTE: Make sure the O-ring is in place on the oil fill
plug/dipstick when checking and changing the
oil (Fig. 53).
Oil Fill Plug/Dipstick
Oil Fill Hole
O-Ring
Full
Add 1.4-1.5 Oz.
(41-44 ml)
To prevent extensive
engine wear and
damage to the unit, always maintain the
proper oil level in the crankcase. Never
operate the unit with the oil level below the
bottom of the dipstick.
CAUTION:
CHANGING THE OIL
For a new engine, change the oil after the first 10 hours of
operation. Change the oil while the engine is still warm. The
oil will flow freely and carry away more impurities.
1. Unplug spark plug boot to prevent accidental starting.
2. Remove the oil fill plug/dipstick.
3. Pour the oil out of the oil fill hole and into a container
by tipping the unit to a vertical position (Fig. 54).
Allow ample time for complete drainage.
Fig. 54
6. Replace the oil fill plug/dipstick.
7. Reconnect the spark plug boot.
4. Wipe up any oil residue on the unit and clean up any
oil that may have spilled. Dispose of the oil
according to Federal, State and local regulations.
5. Refill the crankcase with 3.4 fluid ounce (100 ml) of
SAE 30 SF, SG, SH oil.
NOTE: Use the bottle and spout saved from initial use to
measure the correct amount of oil. The top of the
label on the bottle measures approximately 3.4
ounces (100 ml) (Fig. 55). Check the level with the
dipstick. If the level is low, add a small amount of
oil and recheck. Do not overfill (Fig. 55).
Fill Level
Fig. 55
Wear gloves to
prevent injury when
handling the unit.
CAUTION:
17
3. Wash the filter in detergent and water (Fig. 57). Rinse
the filter thoroughly and allow it to dry.
4. Apply enough clean SAE 30 motor oil to lightly coat
the filter (Fig. 58).
Fig. 57
5. Squeeze the filter to spread and remove excess oil
(Fig. 59).
Fig. 59
Fig. 58
MAINTENANCE AND REPAIR INSTRUCTIONS
AIR FILTER MAINTENANCE
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain
your air filter properly can result in poor performance or
can cause permanent damage to your engine.
1. Open the air filter cover. Push the tab on the right
side of the cover inward. Then pull the air filter cover
out and to the left (Fig. 56).
NOTE: It may be necessary to remove the fuel cap to
completely remove the air filter cover.
2. Remove the air filter (Fig. 56).
Air Filter
Air Filter Cover
Tab
Fig. 56
To avoid serious
personal injury,
always turn the unit off and allow it to cool
before you clean or service it.
WARNING:
18
Fig. 60
Back Plate Slot
Slots
6. Replace the filter (Fig. 60).
NOTE: If the unit is operated without the air filter, you
will VOID the warranty.
7. Reinstall the air filter cover. Position the hooks on
the left side of the air filter cover into the slots at the
left side of the back plate (Fig. 60).
NOTE: It may be necessary to remove the fuel cap to
reinstall the air filter cover.
8. Swing the cover to the right until the tab on the air
filter cover snaps into place in the slot on the back
plate (Fig. 60).
9. Replace the fuel cap if it was removed.
Back Plate
CARBURETOR ADJUSTMENT
The idle speed of the engine is adjustable. An idle
adjustment screw is reached though a hole in the top of
the engine cover (Fig. 61).
NOTE: Careless adjustments can seriously damage your
unit. An authorized service dealer should make
carburetor adjustments.
Check Fuel
Old fuel is usually the reason for improper unit
performance. Drain and refill the tank with fresh fuel prior
to making any adjustments. Refer to Oil and Fuel
Information.
MAINTENANCE AND REPAIR INSTRUCTIONS
Idle Adjustment Screw
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow. This is
often mistaken for an out of adjustment carburetor.
Check the condition of the air filter before adjusting the
idle speed screw. Refer to Air Filter Maintenance.
Adjust Idle Speed Screw
If, after checking the fuel and cleaning the air filter, the
engine still will not idle, adjust the idle speed screw as
follows:
1. Start the engine and let it run at a high idle for a minute
to warm up. Refer to Starting/Stopping Instructions.
2. Release the throttle trigger and let the engine idle. If the
engine stops, insert a small phillips or flat blade screwdriver
into the hole in the air filter/muffler cover (Fig. 61). Turn
the idle speed screw in, clockwise, 1/8 of a turn at a
time (as needed) until the engine idles smoothly.
NOTE: The cutting attachment should not rotate when
the engine idles.
3. If the cutting attachment rotates when the engine idles,
turn the idle speed screw counterclockwise 1/8 of a
turn at a time (as needed), to reduce idle speed.
Checking the fuel, cleaning the air filter, and adjusting
the idle speed should solve most engine problems. If not
and all of the following are true:
the engine will not idle
the engine hesitates or stalls on acceleration
there is a loss of engine power
Have the carburetor adjusted by an authorized service dealer.
Fig. 61
The cutting
attachment may spin
during idle speed adjustments. Wear
protective clothing and observe all safety
instructions to prevent serious personal injury.
WARNING:
To prevent serious
personal injury,
make sure the cutting attachment has
stopped rotating before you turn it off and
set it down.
WARNING:
19
4. Disconnect the spark plug wire.
5. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning a 5/8 in.
socket counterclockwise.
6. Remove the engine cover (Fig. 63).
7. Clean dirt from around the rocker arm cover.
Remove the screw holding the rocker arm cover with
a large flat blade screwdriver or Torx T-25 bit
(Fig. 65). Remove the rocker arm cover and gasket.
3. Remove the screw behind the engine cover (Fig. 64).
Rocker Arm Cover
Screw
Fig. 64
Fig. 65
Spark Plug Hole
8. Pull the starter rope slowly to bring the piston to the top
of its travel, (known as top dead center). Check that:
The piston is at the top of its travel while looking in
the spark plug hole (Fig. 65)
Both rocker arms move freely, and both valves are
closed
If these statements are not true, repeat this step.
9. Slide the feeler gauge between the rocker arm and
the valve return spring. Measure the clearance
between the valve stem and rocker arm (Fig. 66).
Measure both the intake and exhaust valves.
The recommended clearance for the intake and exhaust
is .003 – .006 in. (.076 – 0.152 mm).
Use a standard automotive feeler gauge at .005 (0.127mm).
The feeler gauge should slide between the rocker arm and
valve stem with a slight amount of resistance, without
binding. Figure 67 shows how to measure the clearance.
Remove
Screws
Fig. 62
Engine Cover
2. Remove the two (2) screws on top of the engine cover
with a Flat-head or T-25 Torx screwdriver (Fig. 63).
Fig. 63
Engine Cover
Muffler
ROCKER ARM CLEARANCE
This requires disassembly of the engine. If you feel
unsure or unqualified to perform this, take the unit to an
authorized service center.
NOTE: Inspect the valve to rocker arm clearance with a
feeler gauge after the first 10 hours of operation
and then every 25 hours of operation thereafter.
The engine must be cold when checking or adjusting
the valve clearance.
This task should be performed inside, in a clean,
dust free area.
1. Remove the muffler cover by pressing down on it,
separating it from the engine cover. Using a flat
blade screwdriver, disengage the middle and front
tabs and slots first. The cover will hinge off from the
rear tab (Fig. 62).
Top View Of The Engine
Front Slot
Front Tab
Middle Tab
Middle Slot
Rear Slot
and Tab
MAINTENANCE AND REPAIR INSTRUCTIONS
20
MAINTENANCE AND REPAIR INSTRUCTIONS
Adjusting Nuts
Feeler Gauge
Rocker Arms
Fig. 66
Fig. 67
Feeler Gauge
Exhaust
Adjusting Nut
Exhaust
Rocker Arm
Exhaust
Clearance:
.003-.006 in.
(.076-0.152 mm)
Exhaust Valve Stem
10. If the clearance is not within specification:
a. Turn the adjusting nut using a 5/16 inch (8 mm)
wrench or nut driver (Fig. 67).
To increase clearance, turn the adjusting nut
counterclockwise.
To decrease clearance, turn the adjusting nut
clockwise.
b. Recheck both clearances, and adjust as necessary.
11. Reinstall the rocker arm cover using a new gasket.
Torque the screw to 20–30 inlb (2.2–3.4 Nm).
12. Reinstall the engine cover. Check alignment of the
cover before tightening the screws. Tighten screws.
13. Reinstall the muffler cover. Slip the rear tab on the
muffler cover into the engine cover rear slot. Then
slide the remaining slots into the tabs until they snap
into place (Fig. 62).
14. Check the spark plug and reinstall. See Replacing
the Spark Plug.
15. Replace the spark plug wire.
INTAKE
EXHAUST
Intake Valve
Stem
Intake Clearance:
.003–.006 in.
(.076–0.152 mm)
0.025 in.
(0.655 mm.)
REPLACING THE SPARK PLUG
Use a replacement part number 180890 spark plug. The
correct air gap is 0.025 in. (0.655 mm.). Remove the plug
after every 25 hours of operation and check its
condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull the cap from the spark plug.
2. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning a 5/8 in.
socket counterclockwise.
3. Replace cracked, fouled or dirty spark plug. Set the air
gap at 0.025 in. (0.655 mm.) using a feeler gauge (Fig. 68).
Fig. 68
4. Install a correctly-gapped spark plug in the cylinder
head. Turn the 5/8 in. socket clockwise until snug.
If using a torque wrench torque to:
110-120 in.•lb. (12.3-13.5 N•m)
Do not over tighten.
Fig. 69
Muffler
Spark Arrestor Screen
Spark Arrestor Cover
Screw
Tab
Slot
SPARK ARRESTOR MAINTENANCE
1. Remove the muffler cover. See Rocker Arm Clearance.
2. With a flat blade screwdriver or Torx T-20 bit,
remove the screw attaching the spark arrestor cover
to the muffler (Fig. 69).
3. Pull the tab on the spark arrestor cover out of the
muffler. Remove the spark arrestor cover.
4. Remove the spark arrestor screen from the spark
arrestor cover.
5. Clean the spark arrestor screen with a wire brush or
replace it.
6. Reinstall the spark arrestor screen, spark arrestor
cover and screw.
Do not sand blast,
scrape or clean
electrodes. Grit in the engine could damage
the cylinder.
WARNING:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82

Troy-Bilt TB425CS Manuel utilisateur

Catégorie
Coupe-herbe
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues