Greenlee 52087647 REV0 Manuel utilisateur

1

OPERATION MANUAL

GATOR

®

Insulated

Battery-Powered

Crimping Tool

Read and understand all of the instructions and

safety information in this manual before operating

this tool.

KEEP THIS MANUAL

EK425VX

EK628VX

Record serial number here

_______________________

(See pg. 14 for

LCD screen instr.)

E114954

REG F770

1000V

95R7

Español.............20

Français............40

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

Table of Contents

Recording Form For Machine Serial Number ................. 1

Table of Contents ........................................................... 2

Safety Symbols .............................................................. 3

General Power Tool Safety Warnings

Work Area Safety ...................................................... 4

Electrical Safety ......................................................... 4

Personal Safety .......................................................... 4

Power Tool Use And Care .......................................4-5

Battery Tool Use And Care ........................................ 5

Service ....................................................................... 5

Special Warnings ....................................................... 5

Tool Specic Safety Information

Cutting and Crimping Hazards .................................. 6

Electrical Hazards ...................................................... 6

Repairs and Modications ......................................... 6

Battery Safety ............................................................ 6

Charger Safety ........................................................... 6

Description ..................................................................... 7

Important Features ......................................................... 7

Identication ................................................................... 8

Specications ................................................................. 8

Decal Location ............................................................... 9

Tool Operation

Training and Qualications ...................................... 10

Pre-Operation Inspection ........................................ 10

Set-Up ................................................................10-11

Handling the Tool During Use .................................. 11

Die Selection ............................................................ 12

Connector Selection ................................................ 12

Die Installation ......................................................... 13

Preparing Cable ....................................................... 13

Operation ................................................................. 14

Carrying the Tool ...................................................... 14

LCD Screen ............................................................. 14

Bluetooth ................................................................. 14

Storage and Cleaning .............................................. 15

Service and Maintenance ............................................. 15

Troubleshooting ....................................................... 16-17

LED Indicator (Red) ...................................................... 17

FCC Certication .......................................................... 18

IC Certication .............................................................. 18

Warranty Information .................................................... 18

Replacement manuals are available upon request at

no charge at www.geenlee.com.

GATOR is a registered trademark of Greenlee Tools, Inc.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

MAKITA is a registered trademark of Makita Corporation.

Blackburn is a registered trademark of

Thomas & Betts International.

Anderson is a trademark of Hubbell Corp.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

Burndy is a registered trademark of Hubbell Corp.

ILSCO is a registered trademark of ILSCO Corp.

Panduit is a registered trademark of Panduit Corp.

T&B is a registered trademark of Thomas & Betts International.

Penn-Union is a trademark of Penn-Union Corp.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

Safety Symbols

In this operator’s manual and on the product, safety

symbols and signal words are used to communicate

important safety information. This section is provided

to improve understanding of these signal words and

symbols.

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

DANGER indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

This symbol means read the operator’s

manual carefully before using the

equipment. The operator’s manual contains

important information on the safe and

proper operation of the equipment.

This symbol means always wear safety

glasses with side shields or goggles when

handling or using this equipment to reduce

the risk of eye injury.

This symbol indicates the risk of hands,

ngers or other body parts being cut or

severed.

This symbol indicates the risk of electrical

shock.

This symbol indicates the risk of arc ash.

This symbol indicates an area not to touch.

This area is not insulated.

This symbol indicates an area OK to touch.

This area is insulated.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

cord suitable for outdoor use reduces the risk of

electric shock.

If operating a power tool in a damp location is

unavoidable, use a RESIDUAL CURRENT DEVICE

(RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or BATTERY pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch on

invites accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in

personal injury.

Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it

was designed.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

GENERAL POWER TOOL SAFETY

WARNINGS*

Read all safety warnings, instructions, illustrations

and speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may result

in electric shock, re and/or serious injury.

* The text used in the General Power Tool Safety Warnings section of this manual is required

from the applicable EN 62841-1 standard to which this tool is tested. This section contains

general safety practices for many different types of power tools. Not every precaution applies

to every tool, and some may not apply to this tool.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR

FUTURE REFERENCE.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery operated

(cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

Electrical safety

Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodied plugs and matching outlets will reduce risk

of electric shock.

Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

When BATTERY pack is not in use, keep it away

from other metal objects, like paper clip, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the BATTERY terminals together may cause

burns or a re.

Under abusive conditions, liquid may be ejected

from the BATTERY; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the BATTERY may cause irritation or burns.

Do not use a BATTERY pack or tool that is damaged

or modiﬁed. Damaged or modied batteries may

exhibit unpredictable behavior resulting in re,

EXPLOSION or risk of injury.

Do not expose a BATTERY pack or tool to ﬁre

or excessive temperature. Exposure to re or

temperature above 265°F (130°C) may cause explosion.

Follow all charging instructions and do not charge

the BATTERY pack or tool outside the temperature

range speciﬁed in the instructions. Charging

improperly or at temperatures outside the specied range

may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts.

This will ensure that the safety of the power tools is

maintained.

Never service damaged BATTERY packs. Service

of BATTERY packs should only be performed by

manufacturer or authorized service providers.

Special Warnings

Hydraulic tools can be heavy and might require

additional support. Never overestimate your ability to

handle the tool.

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/

or remove the BATTERY pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

Battery Tool Use and Care

Recharge only with the charger speciﬁed by the

manufacturer. A charger that is suitable for one type of

BATTERY pack may create a risk of re when used with

another BATTERY pack.

Use power tool only with speciﬁcally designated

BATTERY packs. Use of any other BATTERY packs

may create a risk of injury and re.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

TOOL SPECIFIC SAFETY

INFORMATION

Cutting and Crimping Hazards

Keep your ﬁngers and hands away from

the tool head during the operating cycle.

Your ngers or hands can be crushed,

fractured or amputated if they become

caught in the tool head or between the tool

head and other objects.

One person must control work process and machine

operation. Only the operator should be in the area when

the tool is running. This helps reduce the risk of injury.

Large forces are generated during use that can

break or throw parts and cause injury. Keep all

unnecessary personnel away from work area. Stand

clear during use and wear appropriate protective

equipment, including eye protection.

Electrical Hazards

This tool is insulated and will

provide a secondary barrier of

insulation protection up to 1000

Volts. Even with this insulated tool,

you must always wear appropriate

PPE as primary protection against

electric shock and arc ash.

Follow all appropriate and required work procedures

and wear all required Personal Protective Equipment

when on jobsite working near energized electrical lines.

If you are not trained and familiar with appropriate

jobsite and PPE requirements do not use this tool.

Repairs and Modiﬁcations

Do not modify tool. Modifying the tool in any

manner may result in personal injury and voidance

of the tool's warranty.

Never repair a damaged head. A head that has been

welded, ground, drilled or modied in any manner can

break during use. To reduce risk of injury, never replace

individual components. Discard damaged heads.

Do not attempt to open the tool. It contains no user-

serviceable parts.

Battery Safety

To reduce the risk of ﬁre, explosion or electric shock:

Do not allow anything to contact the battery terminals.

Do not immerse the batteries in liquid. Liquid may create

a short circuit and damage the battery. If batteries

are immersed contact your service center for proper

handling.

Do not place the battery into a pocket, tool pouch, or

tool box with conductive objects. Conductive objects

may create a short circuit and damage the battery.

Do not place a battery on moist ground or grass.

Moisture may create a short circuit and damage the

battery.

Do not attempt to open the battery. It contains no user

serviceable parts.

Do not store the battery at more than 104 °F (40 °C)

or less than -4 °F (-20 °C). Damage to the battery

can result.

Do not dispose of batteries in a re. They

will vent fumes and may explode.

Failure to observe this warning could result

in severe injury from harmful fumes or

burns from ying debris.

Charger Safety

Read the instructions supplied with the battery charger.

Do not use another manufacturer's charger. Other

manufacturers' chargers may overcharge and damage

the battery or cause injury.

This section contains important safety information

that is specic to this tool.

Read these precautions carefully before using the

tool to reduce the risk of electrical shock or serious

personal injury.

Improper operation or service presents a risk of

serious injury or death from electric shock, arc ash,

thermal burns, cutting, crushing, and other hazards.

SAVE THESE INSTRUCTIONS!

A compartment in the tool carrying case is

included to keep this manual with the tool to

reference before each operation.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Important Features

• The tool incorporates an automatic retraction, that

returns the ram to the starting position when the

maximum force is achieved.

• The tool is equipped with a special brake, that

stops the forward motion of the ram when the trigger

is released.

• The heads have been designed to rotate around the

longitudinal axis in order to gain the best access to

tight corners and other difcult working areas.

• This tool is equipped with a pressure sensor that can

help alert the user of an incomplete cycle.

• If the tool is manually retracted before completion of a

cycle, the red LED and an audible beep will be active

for 2 seconds.

• If the tool is unable to reach the required crimp force,

the red LED, work light, and an audble beep will pulse

until after the trigger is released.

Description

Greenlee Insulated Battery-Powered In-Line Crimpers

are hand-held, self-contained crimping tools with

removable jaws.

These tools are insulated and will provide a secondary

protection up to 1000 Volts when used with appropriate

Personal Protection Equipment and safety procedures

and in accordance with this manual.

These tools have Bluetooth

®

connectivity and an

LCD screen.

All specications are nominal and may change as

design improvements occur.

These tools are protected by U.S. Patent Nos.

6,276,186, 6,401,515, 6,718,870, 7,086,979, 7,216,523

and 7,254,982.

Patent pending.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

Identiﬁcation

1. Lock Pin

2. Jaw

3. Jaw Cover

4. Retract Button

5. LCD Screen

6. Battery Catridge

7. LED Indicator (red)

8. Lanyard Ring

9. LED Work Light (white)

10. Trigger

11. Tri-barrier Insulation Collar

12. Die Release Button

EK425VX

EK628VX

1

11

10

9

8

7

6

5

11

10

9

8

7

6

5

4

3

2

12

Speciﬁcations

Crimping Tool

Length (with battery)

EK425VX .................................................................................................. 15.5" (393 mm)

EK628X ..................................................................................................... 17.8" (453 mm)

Width ............................................................................................................. 2.95" (75 mm)

Depth ........................................................................................................... 4.92" (125 mm)

Weight ............................................................................................................. 6.4 lb (2.9 kg)

Crimping Force ................................................................................................6 tons (53kN)

Recommended Operating Temperature Range .................-4 °F to 104 °F (-20 °C to 40 °C)

Battery Technology ..................................................................... MAKITA

®

LXT

®

Lithium ion

BL1815, BL1820, BL1830, BL1840, BL1850

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

C

D

B

A

E

G

F

Decals & Location

A. Model Identication

B. Brand and MFG

Identication

C. Live Electricity

Warning

D. VDE Certication/

Year of Last Service

E. Inspection Warning

F. FCC Certication

G. MFG Address Decal

52086903 REV2

EK425VX/EK628VX

CRIMP TOOL For use with UL listed

wire connectors identiﬁed in the

instructions provided. <E119270>

Pat. 6,276,186, 6,401,515, 6,718,870, 7,086,979, 7,216,523 and 7,254,982 Patent pending

E119270

For use only with 18V Makita battery

E114954

A.

52086902 REV1

B.

FCC ID: RFR-550 • IC: 4957A-5502

Model: X

This device complies with Part 15 of the FCC Rules and with Industry

Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation

52087786

F.

C.

D.

REG F770

1000V

REG F770

1000V

HE.18561

E.

52087634 REV 2

Color: PMS 27-8C, PMS 4-8C, and Black

Material: 3M material with laminate or

enginnering approved equivalent

4.51”

R 0.06” x 4

1.58”

52087634 REV2

D

o

n

o

t

u

s

e

i

f

d

a

m

a

g

e

o

r

h

y

d

r

a

u

l

i

c

o

i

l

i

s

o

b

s

e

r

v

e

d

.

D

a

m

a

g

e

m

a

y

c

o

m

p

r

o

m

i

s

e

i

n

s

u

l

a

t

i

o

n

.

I

n

s

p

e

c

t

o

l

b

e

f

o

r

e

a

c

h

u

s

e

.

u

t

i

l

i

s

a

t

i

o

n

.

N

e

p

a

s

u

t

i

l

i

s

e

r

s

i

d

e

s

d

é

g

â

t

s

o

u

d

e

l

’

h

u

i

l

e

L

e

s

d

é

g

â

t

s

p

e

u

v

e

n

t

c

o

m

p

r

o

m

e

t

r

e

l

'

i

s

o

l

a

t

i

o

n

d

e

l

’

o

u

t

i

l

.

I

n

s

p

e

c

t

e

r

l

'

o

u

t

i

l

a

v

a

n

t

c

h

a

q

u

e

d

e

u

s

a

r

.

S

i

l

a

h

e

r

a

m

i

e

n

t

a

e

s

t

á

d

a

ñ

a

d

a

o

s

e

h

a

t

i

r

a

d

o

a

c

e

i

t

e

h

i

d

r

á

u

l

i

c

o

,

n

o

l

a

u

s

e

.

E

l

d

a

ñ

o

p

u

e

d

e

c

o

m

p

r

o

m

e

t

e

r

e

l

i

n

s

u

l

a

c

i

ó

n

.

I

n

s

p

e

c

i

o

n

e

l

a

h

e

r

a

m

i

e

n

t

a

n

t

e

s

h

y

d

r

a

u

l

i

q

u

e

s

o

n

t

o

b

s

e

r

v

é

s

.

A

V

E

R

T

I

S

E

M

E

N

T

A

D

V

E

R

T

E

N

C

I

A

G.

GREENLEE

Greenlee Tools Inc.

4455 Boeing Drive,

Rockford IL

61109-2988 USA

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

TOOL OPERATION

Training and Qualiﬁcations

Ensure that you are trained and qualied by your

employer for any tasks using this tool, especially in

a live line environment. When required, such as for

installation, removal and repair of lines energized at

more than 600V, ensure at least a second trained and

qualied person is present at appropriate distance.

Follow all training and proper live electricity jobsite

safety precautions, see also OSHA standard for electric

power generation, transmission and distribution (29

CFR 1910.269) and NEC 70E: Standard for Electrical

Safety in the Workplace.

Before operating this tool, read and understand:

• This operator's manual

• The battery/charger manual

• The instructions for any other equipment used

with this tool

• Markings on the tool

• Required worksite safety procedures

Pre-Operation Inspection

Daily before use, inspect your

electrical tool and correct any

problems to reduce the risk of

serious injury from electric shock,

crushing injures, equipment failure

and other causes, and to prevent

tool damage.

1. Remove battery from tool.

2. Clean any oil, grease or dirt from the tool body

and tool head, including handles and controls. The

presence of excess oil, grease or dirt can harm the

integrity of the insulation barrier. A clean tool also

aids inspection and helps prevent the tool or control

from slipping from your grip.

3. Always inspect the tool before each use:

• Look for wear or damage, such as cracks, gouges,

or chips to housing.

• Closely inspect the Tri-Barrier Insulation Collar for

cracks, gouges, or chips.

• Look for leaking hydraulic oil.

• Inspect the rotation of the head assembly. Fully

retract the ram. The head should be free to rotate.

• Check the die set.

•

Be sure the tool is clean, dry and free of contaminants.

If damage to housing or Tri-Barrier Insulation Collar is

observed or suspected, or if hydraulic oil has leaked

from the tool, do not use the tool. Contact Greenlee

Customer Service at 800-435-0786 for warranty service

or repair.

Tool damage may compromise insulation and present

a risk of electric shock or arc ash, or cause the tool to

break during use, producing projectiles that can injure

nearby personnel.

The tool must be returned to Greenlee for dielectric

testing of insulation at 2 years or 5000 cycles, whichever

is sooner. See page 15 for service and maintenance.

This tool is not intended for use in marine applications.

Do not use in temperatures below -4 °F (-20 °C) or over

104 °F (40 °C). Extreme temperatures may damage

the tool and compromise the insulation or increase

likelihood of personal injury.

Do not use this tool in the rain, snow or other potentially

dangerous weather conditions; this may compromise

the tool's insulation.

Set-Up

Inspect the jobsite in accordance with OSHA

Employer work speciﬁcation requirements.

To the extent a live circuit can be de-energized,

always de-energize the circuit before beginning work.

Follow all workplace procedures for control of

hazardous energy to prevent unintended energization

while working. Always handle the line as though it is

energized, even if it has been de-energized. When hot

work is required, conrm that nominal voltage is below

1000V and measure voltage before beginning work.

Follow set up and operating instructions to reduce

the risk of injury from crushing, electrical shock

and other causes and to prevent tool damage.

1. Conrm work area safety (See, General Safety

Warnings on pg. 4). Operate in a clear, level, stable,

dry location. Do not use tool while standing in water

or in contact with other conductors.

Tri-Barrier

Insulation

Collar

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

2. Inspect the work to be done and determine the

correct tool for the application. Using an incorrect

tool for an application can cause injury, damage

the tool, or cause personal injury. (See, this tool's

specications on pg. 8.)

3. Conrm that the tool and head have been inspected

as directed above.

Handling the Tool During Use

To avoid contact with energized parts and reduce the

risk of electrocution or arc ash, and to avoid cutting or

pinching injuries, hold the tool properly during use:

1. Touch the tool only on the insulated handle. (Fig. 1)

2. Do not touch any part of the tool past the Tri-Barrier

Insulation Collar. Do not grip the collar. Keep hands

away from head. (Fig. 2)

3. Keep the tool at arm's length, away from your body.

(Fig. 3)

4. Do not touch the cable. (Fig. 4)

5. Do not cut or crimp multi-phase cable or multiple

cables at the same time.

Set-Up (cont'd)

Fig. 3

Tri-Barrier

Insulation

Collar

Fig. 2

No Multi-Phase

Cable

No Multiple

Cables

Fig. 5

1000V

Fig. 1

Not

Insulated

Not

Insulated

Fig. 4

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Die Selection CJ22 Jaw and KA22/KC22-type

Note: These tools will provide a cUL and UL classiﬁed crimp ONLY when used with the CJ22 jaws

and KA22- or KC22-type dies.

Note: These tools will provide 53 kN (6 tons) of crimping force when used with the CJ22 jaws.

Crimps made on copper cable with Greenlee KC22-type dies and the copper connectors listed here are cUL and UL classied.

Crimps made on copper or aluminum cable with Greenlee KA22-type dies and the dual-rated aluminum connectors listed

here are cUL and UL classied.

Refer to “Connector Selection” for brand names and model numbers of appropriate lugs as well as crimping instructions.

Dies for Dual-rated Aluminum Connectors

Catalog Number UPC Number Cable Size

KA22-8 06744 8 AWG

KA22-6 06745 6 AWG

KA22-4 06746 4 AWG

KA22-2 06747 2 AWG

KA22-1 06749 1 AWG

KA22-1/0 06750 1/0 AWG

KA22-2/0 06751 2/0 AWG

KA22-3/0 06752 3/0 AWG

KA22-4/0 06753 4/0 AWG

KA22-250 06754 250 kcmil

KA22-300 06755 300 kcmil

KA22-350 06756 350 kcmil

Dies for Copper Connectors

Catalog Number UPC Number Cable Size Color Code

KC22-8 03079 8 AWG Red

KC22-6 03080 6 AWG Blue

KC22-4 03081 4 AWG Gray

KC22-2 03082 2 AWG Brown

KC22-1 03083 1 AWG Green

KC22-1/0 03084 1/0 AWG Pink

KC22-2/0 03085 2/0 AWG Black

KC22-3/0 03086 3/0 AWG Orange

KC22-4/0 03087 4/0 AWG Purple

KC22-250 03088 250 kcmil Yellow

KC22-300 03089 300 kcmil White

KC22-350 03090 350 kcmil Red

KC22-400 03091 400 kcmil Blue

KC22-500 03092 500 kcmil Brown

KC22-600B 03094 600 kcmil Green

Connector Selection

CJ22 Crimping Jaw Range: Copper — 8 AWG to 600 kcmil†; Dual-rated Aluminum — 8 AWG to 350 kcmil

When used with KC22-type dies, these tools are cUL and UL classied for use with the following connector brands:

Connector

Type

Barrel

Type

Anderson

™

Blackburn

®

Burndy

®

ILSCO

®

Panduit

®

T&B

®

Penn-

Union

™

†

No. of

Crimps*

Copper

Splice

Short VHSS CSP YS-L

s

CT SCSS/SCS 54504-54518 BCU

A

Long VHS CU YS

s

CTL SCL/SCH 54804-54818 BBCU

Copper

Lugs

Short VHCS CTL-2/CTL

YA-2LN/YA-L/YA-2L

YA/YA-L-TC/YA-L-2TC

CSW

CRA/CRB

LCAS/LCA

LCD

54104-54118

54204-54218

BLU

Long VHCL CTL-L/LCN YA-2N

CLN/CLW

CRA-L/CRB-L

CRA-2L/CRB-2L

LCB/LCC

54930BE-54918BE

54850BE-54876BE

BBLU

When used with KA22-type dies, these tools are cUL and UL classied for use with the following connector brands:

Connector Type

Barrel

Type

Anderson

™

Blackburn

®

Burndy

®

ILSCO

®

Panduit

®

** T&B

®

Penn-

Union

™

No. of

Crimps*

Dual-rated

Aluminum Splice

— VACS ASP YS-A

AS

ASN

SA 60501-60565 PIK

B

Dual-rated

Aluminum Lugs

— VACL ATL

YA-A

YA-ATN

ACL/ACN

2ACL/2ACN

ALNS/ALNN/ALND

LAA/LAB

60101-60166

60230-60267

BLUA

* Use the number of crimps listed in the last column instead of the number provided with the connector:

A — 8 to 1/0 AWG: 1 crimp B — 8 to 2 AWG: 2 crimps

2/0 AWG to 600 kcmil: 2 crimps 1 to 3/0 AWG: 3 crimps

4/0 AWG to 350 kcmil: 4 crimps

** 6 AWG to 350 kcmil

† 500 kcmil maximum with Penn-Union connectors

s

8 AWG to 350 kcmil with Burndy copper splices

95R7

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

13

Die Installation

Installing K22, KA22, and KC22-type Dies

in CJ22 Jaw

1. Pull the die release button.

2. Slide the die into the crimping head until it "snaps"

into place.

3. Properly position the second die. Repeat step 2.

Installing W-type Dies in CJD3 Type Jaws

1. Pull the die release button.

2. Slide the die adapter (Greenlee part number

50042920) into crimping head until it "snaps" into

place.

Note: The die adapters have the "D

3

" die proﬁle. No

additional dies are needed if the connector to be

crimped requires a "D

3

" die.

3. Repeat for the other adapter.

4. Push the W-type die detent and slide the W-type die

into place

5. Repeat step 4 to properly position the second die.

The following W-type dies may be used with the

Greenlee EK425VX Tool:

• Greenlee KD6 series

• Burndy W and X series

• ILSCO ND seriess

• Huskie HT58 series

• Panduit CD-2001 series

• Other industry W-type dies

Preparing Cable

Follow the lug manufacturer’s instructions for

appropriate cable strip length.

Crimping Direction

(evenly spaced)

First Compression

Crimping Direction

SIDE A

(evenly spaced)

Crimping Direction

SIDE B

(evenly spaced)

First Compression

SIDE A

First Compression

SIDE B

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

14

Operation

1. Wear appropriate Personal Protective Equipment,

including eye, face, head and arm protection and

other PPE as required by your employer, and/or as

appropriate for the job.

2. Position the crimping head over the properly

assembled connector.

3. Ensure arm's length distance between tool and user

(Fig. 3, pg. 11) then pull the trigger to make the crimp.

Note: Trigger activates white LED work light which

remains on for 10 seconds after trigger is released.

4. Hold the trigger down until the crimping tool

achieves pressure relief, which is accompanied by

an audible “pop”.

5. The ram will return automatically to the starting

position.

The process can be interrupted at any moment by

releasing the trigger. By actuating the retract button,

the ram will return to the starting position. If you do not

hear the sound of the relief valve or the ram does not

automatically retract, the crimp is not complete.

Note: This tool is not designed for continuous use. After

100 cycles allow the tool to cool for 15 minutes.

Do not twist work piece or tool during operation. Failure

could result.

* After completing the last crimp with W-type dies on an

aluminum connector, wipe off the excess oxide inhibitor.

Carrying the Tool

The carrying ring and carrying strap are for carrying

only. Never hang or suspend the tool by the strap.

Display LCD Screen Information Shown

0

1

PSI

P

Bluetooth

®

status, battery charge, current pressure, max. pressure. Press and hold both

buttons to change units, select with right button, and conrm by jogging the tool.

2

INFO

123456AB001

FW: 2.0

Firmware version, serialnumber

3

CURRENT USER : 1

SINGLE CLICK

MRS+

Current user. Press and hold both buttons to change user and toggle between single

click and double click operation. Change the user and operation with the right button

and conrm the selection by tapping the trigger. Selecting single click will allow the user to

operate the tool with one trigger pull. Selecting double click will require the user to press

the trigger twice within 1/2 second to operate the tool.

4

NEXT SERVICE

5000 OPS

730 DAYS

Cycles and days until next service.

5

TOTAL:

T=

Q=

n=

0.0h

0.0Ah

0

Elapsed operating hours (T), Ah used (Q), and number of cycles (n) since date of

manufacture.

LCD Screen

This tool has an LCD screen that displays information

about the tool. Turn on the screen by inserting the

battery and tapping the trigger.

In normal operation, cycle through the various displays

using the left and right buttons on either side of the

screen.

The LCD screen will also display error codes in the

event of abnormal operation. See pg. 17 for error code

troubleshooting.

Bluetooth/I-Press App

This tool has Bluetooth capability that allows the tool

to communicate with the Greenlee i-press App on your

smart device.

1. Install the "i-press Klauke Software Solutions"

app from the App Store or Google Play. Open

the app on your smart device and select the

Greenlee option.

2. Switch on the Bluetooth function on your smart

device and activate the tool to establish a

connection.

3. The app will allow you to create projects,

personalize your tool, and display tool pressure

readings, battery charge, the last service date, and

more. Instructions how to use the app are shown in

the i-press app itself; alternately, request MA6864

brochure from any Greenlee distributor.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

15

Service and Maintenance

If damage to tool's housing or Tri-Barrier Insulation

Collar is observed or suspected, or if hydraulic oil has

leaked from the tool, do not use the tool. Tool safety

could be compromised. Return tool immediately to

Greenlee at 800-435-0786 for warranty service or repair.

Proper maintenance of the tool including periodic

replacement of the tool's Tri-Barrier Insulation Collar

componentry is required.

On the earlier of either 2 years or 5,000 cycles, Factory

Service of the tool must be completed. Factory

Service includes replacement of tool's di-electric

hydraulic oil, replacement of tool's Tri-Barrier Insulation

Collar componentry and di-electric testing of tool

by trained technicians as well as general review of

mechanical function.

The Tri-Barrier Insulation Collar componentry on the

tool must be replaced every

two years. Failure to follow

the required Factory Service

schedule could compromise the

insulating properties of the tool

and result in serious injury.

The tool will alert when the

earlier of either 2 years or

5,000 cycles is approaching and will alert again when

Factory Service is required. When Factory Service date

is approaching or arrived, contact Greenlee Customer

Service. Expedited shipping is available. After contacting

Greenlee Customer Service, the tool should be sent to

the Greenlee Factory Service Center at 4411 Boeing Dr.,

Rockford, IL 61109.

Use this schedule to help track when your tool is due in

for Factory Service.

To avoid tool damage or compromise of the tool's

insulation barriers: clean the housing with a damp cloth

and mild detergent after every use. Dry completely and

fully retract the ram. Place the tool in the carrying case

and store in a cool dry place. Do not use the carrying

strap to hang or suspend tool. Avoid dropping the

Storage and Cleaning

tool. If necessary, recharge the batteries. Refer to the

instructions supplied with the battery charger. Store tool

in proper manufacturer provided protective enclosure.

Keep this manual with the tool.

Routine Service Calendar Service Date Notes

Date Placed into Service

Date of First Factory Service

Date of Second Factory Service

Date of Third Factory Service

Date of Fourth Factory Service

Date of Fifth Factory Service

Date of Sixth Factory Service

Date of Seventh Factory Service

Date of Eighth Factory Service

Date of Ninth Factory Service

Date of Tenth Factory Service

Date of Eleventh Factory Service

Do not perform any service or maintenance other

than as described in this manual. Personal injury or

damage to the tool may result.

The Tri-Barrier Insulating componentry must be

replaced by Greenlee factory technicians every

two years. Failure to replace Tri-Barrier Insulating

componentry may result in personal injury or damage.

Tri-Barrier

Insulation

Collar

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

16

Problem Possible Cause Probable Remedy

Tool is inoperative. Dirt, contaminants, etc., in

ram area oftool.

Clean tool.

Tool components worn or

damaged.

Contact Greenlee Customer Service at

800-435-0786 for warranty service or repair.

Motor is inoperative. Low or uncharged battery. Try known charged battery. Inoperative battery may be

discharged or may have reached life expectancy.

Broken switch components. Contact Greenlee Customer Service at

800-435-0786 for warranty service or repair.

Motor runs but tool will

not complete a cycle.

Oil level low. Contact Greenlee Customer Service at

800-435-0786 for warranty service or repair.

Air in hydraulic system. Pull trigger and hold retract button simultaneously.

Run for approximately 10 seconds, and then attempt

to cycle the tool. If unsuccessful, contact Greenlee

Customer Service at 800-435-0786 for warranty

service or repair.

Cold oil. Pull trigger and hold retract button simultaneously to

warm oil. Store tool in warm area.

Tool loses oil. Damaged seal. Contact Greenlee Customer Service at

800-435-0786 for warranty service or repair.

Troubleshooting

Before You Begin

1. Make sure that the battery is charged. Recheck

the battery after several minutes to make sure the

battery is holding its charge.

2. Use a nonﬂammable contact cleaner or pencil

eraser to clean the electrical contacts on the battery

and tool.

3. Reinstall the battery and check the tool again.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

17

LED Indicator (red)

This tool is equipped with a special circuit board

incorporating several important features to inform

the user about the current status of the unit. The LED

signals in the following cases:

What happens Signal What it means

What to

do

Tool will not start,

and constant light for

20seconds when trigger

is released

Battery

charge low

Change

or charge

battery

Tool will stop, and

constant light for

20seconds after trigger

is released

Tool will stop, and

ﬂashing light for

20seconds when

trigger is released

Motor current

exceeds 20A

during cycle

Let tool

cool

Circuit has

become too hot

Flashing light for 20

seconds at end of cycle

and

audible

warning

Indicates 4,750

cycles exceeded

or 21 months

exceeded

Send tool

in for

service

Error

Code

Meaning Action

1 Overcurrent fuse Seek Service

2 Overcurrent comparator Seek Service

3 Overheated circuit board Cool Tool

4 Overheated battery Cool Battery

5

Battery empty; operation

stops

Charge Battery

6

Faulty crimp; complete

cycle

Seek Service

7

Faulty crimp; incomplete

cycle

Seek Service

8 Low battery Charge Battery

9 Battery empty Charge Battery

10

Real-time clock battery

low

Seek Service

11 Tool deactivated Seek Service

12 Service necessary Seek Service

13

Real-time clock not

found

1. Re-insert Battery

2. Seek Service

14 Bluetooth

®

unit not found

1. Re-insert Battery

2. Seek Service

15 [Not Used]

16

Pressure sensor not

found

Seek Service

17 Burst pressure exceeded Seek Service

18

Battery temperature too

low

Warm Battery

19

Blinking Screen 4,750

cycles exceeded

Seek Service

If certain problems arise with the tool, an error code

appears on the LCD screen (see pg. 14).

Troubleshooting (cont'd)

Note: The tool will indicate when re-certication is near.

Starting at 4,750 cycles or 21 months (whichever occurs

rst), the red LED and work LED will ash, an audible

warning will sound, and the LED will display SERVICE

NECESSARY for 20 seconds after every cycle. After

5,000 cycles or 2 years, the tool will not operate unless

the battery is removed and reinstalled. Only one cycle is

possible each time the battery is reinstalled.

Gator

®

Insulated Battery-Powered In-Line Crimpers

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

18

Model X—FCC ID: RFR-S50; IC ID:

4957A-S50

USA requirements:

Responsible party: Greenlee Tools, Inc.

Rockford, IL 61109 USA

Note: This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio com-

munications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case

the user will be required to correct the interference at

his own expense.

This device complies with the RF exposure SAR

test exclusion requirements for portable devices, if a

minimum separation distance is kept. However, the

device shall be used in such a manner that the potential

for human contact during normal operation is minimized.

Canada requirements:

This device complies with Industry Canada’s license-

exempt RSSs. Operation is subject to the following

two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including

interference that may cause undesired operation of

the device.

Le présent appareil est conforme aux CNR d’Industrie

Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions

suivantes:

1) l’appareil ne doit pas produire de brouillage;

2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est suscep-

tible d’en compromettre le fonctionnement.

Warranty

Model "VX" insulated tools are covered by the standard

Greenlee Limited Warranty for a period of 7 years, this

limited warranty excludes coverage for the Tri-Barrier

Insulation Collar and componentry.

The Tri-Barrier Insulation Collar and componentry are

covered by the standard Greenlee Limited Warranty for

a period of 2 years.

To review the standard Greenlee Limited Warranty, visit

www.greenlee.com.

Do not perform any service or maintenance other

than as described in this manual. Personal injury or

damage to the tool may result.

The Tri-Barrier Insulating componentry must be

replaced by the factory every two years. Failure to

replace may result in personal injury or damage.

For warranty claims and/or factory service please

contact Greenlee Customer Service by phone at

800-435-0786.

Shipping address:

Greenlee Factory Service Center

4411 Boeing Dr., Rockford, IL 61109

Reminder: Warranty claim is void if warranty seal on tool

is broken.

19

4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070

USA Tel: 800-435-0786

Fax: 800-451-2632

Canada Tel: 800-435-0786

Fax: 800-524-2853

International Tel: +1-815-397-7070

Fax: +1-815-397-9247

www.greenlee.com

Gator

®

Insulated Battery-powered In-line Crimper

20

MANUAL DE FUNCIONAMIENTO

Engarzadora GATOR

®

aislada accionada

porbatería

Lea y comprenda todas las instrucciones y la

información de seguridad de este manual antes

de utilizar esta herramienta.

GUARDE ESTE MANUAL

EK425VX

EK628VX

Registrar el número de

serie aquí

_______________________

(Consulte la pág. 14 para

ver las instrucciones de la

pantalla LCD)

E114954

REG F770

1000V

95R7

La page est en cours de chargement...

Greenlee 52087647 REV0 Manuel utilisateur

Greenlee 52087647 REV0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents