Greenlee 52087647 REV0 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
1
OPERATION MANUAL
GATOR
®
Insulated
Battery-Powered
Crimping Tool
52087647 © 2019 Greenlee Tools, Inc. 10/19
Read and understand all of the instructions and
safety information in this manual before operating
this tool.
KEEP THIS MANUAL
EK425VX
EK628VX
Record serial number here
_______________________
(See pg. 14 for
LCD screen instr.)
E114954
REG F770
1000V
95R7
Español.............20
Français............40
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Table of Contents
Recording Form For Machine Serial Number ................. 1
Table of Contents ........................................................... 2
Safety Symbols .............................................................. 3
General Power Tool Safety Warnings
Work Area Safety ...................................................... 4
Electrical Safety ......................................................... 4
Personal Safety .......................................................... 4
Power Tool Use And Care .......................................4-5
Battery Tool Use And Care ........................................ 5
Service ....................................................................... 5
Special Warnings ....................................................... 5
Tool Specic Safety Information
Cutting and Crimping Hazards .................................. 6
Electrical Hazards ...................................................... 6
Repairs and Modications ......................................... 6
Battery Safety ............................................................ 6
Charger Safety ........................................................... 6
Description ..................................................................... 7
Important Features ......................................................... 7
Identication ................................................................... 8
Specications ................................................................. 8
Decal Location ............................................................... 9
Tool Operation
Training and Qualications ...................................... 10
Pre-Operation Inspection ........................................ 10
Set-Up ................................................................10-11
Handling the Tool During Use .................................. 11
Die Selection ............................................................ 12
Connector Selection ................................................ 12
Die Installation ......................................................... 13
Preparing Cable ....................................................... 13
Operation ................................................................. 14
Carrying the Tool ...................................................... 14
LCD Screen ............................................................. 14
Bluetooth ................................................................. 14
Storage and Cleaning .............................................. 15
Service and Maintenance ............................................. 15
Troubleshooting ....................................................... 16-17
LED Indicator (Red) ...................................................... 17
FCC Certication .......................................................... 18
IC Certication .............................................................. 18
Warranty Information .................................................... 18
Replacement manuals are available upon request at
no charge at www.geenlee.com.
GATOR is a registered trademark of Greenlee Tools, Inc.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
MAKITA is a registered trademark of Makita Corporation.
Blackburn is a registered trademark of
Thomas & Betts International.
Anderson is a trademark of Hubbell Corp.
Do not discard this product or throw away!
For recycling information, go to www.greenlee.com.
Burndy is a registered trademark of Hubbell Corp.
ILSCO is a registered trademark of ILSCO Corp.
Panduit is a registered trademark of Panduit Corp.
T&B is a registered trademark of Thomas & Betts International.
Penn-Union is a trademark of Penn-Union Corp.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
Safety Symbols
In this operator’s manual and on the product, safety
symbols and signal words are used to communicate
important safety information. This section is provided
to improve understanding of these signal words and
symbols.
This is the safety alert symbol. It is used to
alert you to potential personal injury
hazards. Obey all safety messages that
follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
This symbol means read the operator’s
manual carefully before using the
equipment. The operator’s manual contains
important information on the safe and
proper operation of the equipment.
This symbol means always wear safety
glasses with side shields or goggles when
handling or using this equipment to reduce
the risk of eye injury.
This symbol indicates the risk of hands,
ngers or other body parts being cut or
severed.
This symbol indicates the risk of electrical
shock.
This symbol indicates the risk of arc ash.
This symbol indicates an area not to touch.
This area is not insulated.
This symbol indicates an area OK to touch.
This area is insulated.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
4
cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a RESIDUAL CURRENT DEVICE
(RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or BATTERY pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch on
invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in
personal injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
Power tool use and care
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
GENERAL POWER TOOL SAFETY
WARNINGS*
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
* The text used in the General Power Tool Safety Warnings section of this manual is required
from the applicable EN 62841-1 standard to which this tool is tested. This section contains
general safety practices for many different types of power tools. Not every precaution applies
to every tool, and some may not apply to this tool.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery operated
(cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
Electrical safety
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk
of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
5
When BATTERY pack is not in use, keep it away
from other metal objects, like paper clip, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the BATTERY terminals together may cause
burns or a re.
Under abusive conditions, liquid may be ejected
from the BATTERY; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the BATTERY may cause irritation or burns.
Do not use a BATTERY pack or tool that is damaged
or modified. Damaged or modied batteries may
exhibit unpredictable behavior resulting in re,
EXPLOSION or risk of injury.
Do not expose a BATTERY pack or tool to fire
or excessive temperature. Exposure to re or
temperature above 265°F (130°C) may cause explosion.
Follow all charging instructions and do not charge
the BATTERY pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tools is
maintained.
Never service damaged BATTERY packs. Service
of BATTERY packs should only be performed by
manufacturer or authorized service providers.
Special Warnings
Hydraulic tools can be heavy and might require
additional support. Never overestimate your ability to
handle the tool.
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/
or remove the BATTERY pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Battery Tool Use and Care
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
BATTERY pack may create a risk of re when used with
another BATTERY pack.
Use power tool only with specifically designated
BATTERY packs. Use of any other BATTERY packs
may create a risk of injury and re.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
6
TOOL SPECIFIC SAFETY
INFORMATION
Cutting and Crimping Hazards
Keep your fingers and hands away from
the tool head during the operating cycle.
Your ngers or hands can be crushed,
fractured or amputated if they become
caught in the tool head or between the tool
head and other objects.
One person must control work process and machine
operation. Only the operator should be in the area when
the tool is running. This helps reduce the risk of injury.
Large forces are generated during use that can
break or throw parts and cause injury. Keep all
unnecessary personnel away from work area. Stand
clear during use and wear appropriate protective
equipment, including eye protection.
Electrical Hazards
This tool is insulated and will
provide a secondary barrier of
insulation protection up to 1000
Volts. Even with this insulated tool,
you must always wear appropriate
PPE as primary protection against
electric shock and arc ash.
Follow all appropriate and required work procedures
and wear all required Personal Protective Equipment
when on jobsite working near energized electrical lines.
If you are not trained and familiar with appropriate
jobsite and PPE requirements do not use this tool.
Repairs and Modifications
Do not modify tool. Modifying the tool in any
manner may result in personal injury and voidance
of the tool's warranty.
Never repair a damaged head. A head that has been
welded, ground, drilled or modied in any manner can
break during use. To reduce risk of injury, never replace
individual components. Discard damaged heads.
Do not attempt to open the tool. It contains no user-
serviceable parts.
Battery Safety
To reduce the risk of fire, explosion or electric shock:
Do not allow anything to contact the battery terminals.
Do not immerse the batteries in liquid. Liquid may create
a short circuit and damage the battery. If batteries
are immersed contact your service center for proper
handling.
Do not place the battery into a pocket, tool pouch, or
tool box with conductive objects. Conductive objects
may create a short circuit and damage the battery.
Do not place a battery on moist ground or grass.
Moisture may create a short circuit and damage the
battery.
Do not attempt to open the battery. It contains no user
serviceable parts.
Do not store the battery at more than 104 °F (40 °C)
or less than -4 °F (-20 °C). Damage to the battery
can result.
Do not dispose of batteries in a re. They
will vent fumes and may explode.
Failure to observe this warning could result
in severe injury from harmful fumes or
burns from ying debris.
Charger Safety
Read the instructions supplied with the battery charger.
Do not use another manufacturer's charger. Other
manufacturers' chargers may overcharge and damage
the battery or cause injury.
This section contains important safety information
that is specic to this tool.
Read these precautions carefully before using the
tool to reduce the risk of electrical shock or serious
personal injury.
Improper operation or service presents a risk of
serious injury or death from electric shock, arc ash,
thermal burns, cutting, crushing, and other hazards.
SAVE THESE INSTRUCTIONS!
A compartment in the tool carrying case is
included to keep this manual with the tool to
reference before each operation.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
7
Important Features
The tool incorporates an automatic retraction, that
returns the ram to the starting position when the
maximum force is achieved.
The tool is equipped with a special brake, that
stops the forward motion of the ram when the trigger
is released.
The heads have been designed to rotate around the
longitudinal axis in order to gain the best access to
tight corners and other difcult working areas.
This tool is equipped with a pressure sensor that can
help alert the user of an incomplete cycle.
If the tool is manually retracted before completion of a
cycle, the red LED and an audible beep will be active
for 2 seconds.
If the tool is unable to reach the required crimp force,
the red LED, work light, and an audble beep will pulse
until after the trigger is released.
Description
Greenlee Insulated Battery-Powered In-Line Crimpers
are hand-held, self-contained crimping tools with
removable jaws.
These tools are insulated and will provide a secondary
protection up to 1000 Volts when used with appropriate
Personal Protection Equipment and safety procedures
and in accordance with this manual.
These tools have Bluetooth
®
connectivity and an
LCD screen.
All specications are nominal and may change as
design improvements occur.
These tools are protected by U.S. Patent Nos.
6,276,186, 6,401,515, 6,718,870, 7,086,979, 7,216,523
and 7,254,982.
Patent pending.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
8
Identification
1. Lock Pin
2. Jaw
3. Jaw Cover
4. Retract Button
5. LCD Screen
6. Battery Catridge
7. LED Indicator (red)
8. Lanyard Ring
9. LED Work Light (white)
10. Trigger
11. Tri-barrier Insulation Collar
12. Die Release Button
EK425VX
EK628VX
1
1
11
10
9
8
7
6
5
11
10
9
8
7
6
5
4
4
3
2
12
Specifications
Crimping Tool
Length (with battery)
EK425VX .................................................................................................. 15.5" (393 mm)
EK628X ..................................................................................................... 17.8" (453 mm)
Width ............................................................................................................. 2.95" (75 mm)
Depth ........................................................................................................... 4.92" (125 mm)
Weight ............................................................................................................. 6.4 lb (2.9 kg)
Crimping Force ................................................................................................6 tons (53kN)
Recommended Operating Temperature Range .................-4 °F to 104 °F (-20 °C to 40 °C)
Battery Technology ..................................................................... MAKITA
®
LXT
®
Lithium ion
BL1815, BL1820, BL1830, BL1840, BL1850
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
9
C
D
B
A
E
G
F
Decals & Location
A. Model Identication
B. Brand and MFG
Identication
C. Live Electricity
Warning
D. VDE Certication/
Year of Last Service
E. Inspection Warning
F. FCC Certication
G. MFG Address Decal
52086903 REV2
EK425VX/EK628VX
CRIMP TOOL For use with UL listed
wire connectors identified in the
instructions provided. <E119270>
Pat. 6,276,186, 6,401,515, 6,718,870, 7,086,979, 7,216,523 and 7,254,982 Patent pending
E119270
For use only with 18V Makita battery
E114954
A.
52086902 REV1
B.
FCC ID: RFR-550 • IC: 4957A-5502
Model: X
This device complies with Part 15 of the FCC Rules and with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation
52087786
F.
C.
D.
REG F770
1000V
REG F770
1000V
HE.18561
E.
52087634 REV 2
Color: PMS 27-8C, PMS 4-8C, and Black
Material: 3M material with laminate or
enginnering approved equivalent
4.51”
R 0.06” x 4
1.58”
52087634 REV2
D
o
n
o
t
u
s
e
i
f
d
a
m
a
g
e
o
r
h
y
d
r
a
u
l
i
c
o
i
l
i
s
o
b
s
e
r
v
e
d
.
D
a
m
a
g
e
m
a
y
c
o
m
p
r
o
m
i
s
e
i
n
s
u
l
a
t
i
o
n
.
I
n
s
p
e
c
t
t
o
o
l
b
e
f
o
r
e
e
a
c
h
u
s
e
.
u
t
i
l
i
s
a
t
i
o
n
.
N
e
p
a
s
u
t
i
l
i
s
e
r
s
i
d
e
s
d
é
g
â
t
s
o
u
d
e
l
h
u
i
l
e
L
e
s
d
é
g
â
t
s
p
e
u
v
e
n
t
c
o
m
p
r
o
m
e
t
t
r
e
l
'
i
s
o
l
a
t
i
o
n
d
e
l
o
u
t
i
l
.
I
n
s
p
e
c
t
e
r
l
'
o
u
t
i
l
a
v
a
n
t
c
h
a
q
u
e
d
e
u
s
a
r
.
S
i
l
a
h
e
r
r
a
m
i
e
n
t
a
e
s
t
á
d
a
ñ
a
d
a
o
s
e
h
a
t
i
r
a
d
o
a
c
e
i
t
e
h
i
d
r
á
u
l
i
c
o
,
n
o
l
a
u
s
e
.
E
l
d
a
ñ
o
p
u
e
d
e
c
o
m
p
r
o
m
e
t
e
r
e
l
i
n
s
u
l
a
c
i
ó
n
.
I
n
s
p
e
c
c
i
o
n
e
l
a
h
e
r
r
a
m
i
e
n
t
a
a
n
t
e
s
h
y
d
r
a
u
l
i
q
u
e
s
o
n
t
o
b
s
e
r
v
é
s
.
A
V
E
R
T
I
S
S
E
M
E
N
T
A
D
V
E
R
T
E
N
C
I
A
G.
GREENLEE
Greenlee Tools Inc.
4455 Boeing Drive,
Rockford IL
61109-2988 USA
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
10
TOOL OPERATION
Training and Qualifications
Ensure that you are trained and qualied by your
employer for any tasks using this tool, especially in
a live line environment. When required, such as for
installation, removal and repair of lines energized at
more than 600V, ensure at least a second trained and
qualied person is present at appropriate distance.
Follow all training and proper live electricity jobsite
safety precautions, see also OSHA standard for electric
power generation, transmission and distribution (29
CFR 1910.269) and NEC 70E: Standard for Electrical
Safety in the Workplace.
Before operating this tool, read and understand:
• This operator's manual
• The battery/charger manual
The instructions for any other equipment used
with this tool
• Markings on the tool
• Required worksite safety procedures
Pre-Operation Inspection
Daily before use, inspect your
electrical tool and correct any
problems to reduce the risk of
serious injury from electric shock,
crushing injures, equipment failure
and other causes, and to prevent
tool damage.
1. Remove battery from tool.
2. Clean any oil, grease or dirt from the tool body
and tool head, including handles and controls. The
presence of excess oil, grease or dirt can harm the
integrity of the insulation barrier. A clean tool also
aids inspection and helps prevent the tool or control
from slipping from your grip.
3. Always inspect the tool before each use:
Look for wear or damage, such as cracks, gouges,
or chips to housing.
Closely inspect the Tri-Barrier Insulation Collar for
cracks, gouges, or chips.
• Look for leaking hydraulic oil.
Inspect the rotation of the head assembly. Fully
retract the ram. The head should be free to rotate.
• Check the die set.
Be sure the tool is clean, dry and free of contaminants.
If damage to housing or Tri-Barrier Insulation Collar is
observed or suspected, or if hydraulic oil has leaked
from the tool, do not use the tool. Contact Greenlee
Customer Service at 800-435-0786 for warranty service
or repair.
Tool damage may compromise insulation and present
a risk of electric shock or arc ash, or cause the tool to
break during use, producing projectiles that can injure
nearby personnel.
The tool must be returned to Greenlee for dielectric
testing of insulation at 2 years or 5000 cycles, whichever
is sooner. See page 15 for service and maintenance.
This tool is not intended for use in marine applications.
Do not use in temperatures below -4 °F (-20 °C) or over
104 °F (40 °C). Extreme temperatures may damage
the tool and compromise the insulation or increase
likelihood of personal injury.
Do not use this tool in the rain, snow or other potentially
dangerous weather conditions; this may compromise
the tool's insulation.
Set-Up
Inspect the jobsite in accordance with OSHA
Employer work specification requirements.
To the extent a live circuit can be de-energized,
always de-energize the circuit before beginning work.
Follow all workplace procedures for control of
hazardous energy to prevent unintended energization
while working. Always handle the line as though it is
energized, even if it has been de-energized. When hot
work is required, conrm that nominal voltage is below
1000V and measure voltage before beginning work.
Follow set up and operating instructions to reduce
the risk of injury from crushing, electrical shock
and other causes and to prevent tool damage.
1. Conrm work area safety (See, General Safety
Warnings on pg. 4). Operate in a clear, level, stable,
dry location. Do not use tool while standing in water
or in contact with other conductors.
Tri-Barrier
Insulation
Collar
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
11
2. Inspect the work to be done and determine the
correct tool for the application. Using an incorrect
tool for an application can cause injury, damage
the tool, or cause personal injury. (See, this tool's
specications on pg. 8.)
3. Conrm that the tool and head have been inspected
as directed above.
Handling the Tool During Use
To avoid contact with energized parts and reduce the
risk of electrocution or arc ash, and to avoid cutting or
pinching injuries, hold the tool properly during use:
1. Touch the tool only on the insulated handle. (Fig. 1)
2. Do not touch any part of the tool past the Tri-Barrier
Insulation Collar. Do not grip the collar. Keep hands
away from head. (Fig. 2)
3. Keep the tool at arm's length, away from your body.
(Fig. 3)
4. Do not touch the cable. (Fig. 4)
5. Do not cut or crimp multi-phase cable or multiple
cables at the same time.
Set-Up (cont'd)
Fig. 3
Tri-Barrier
Insulation
Collar
Fig. 2
No Multi-Phase
Cable
No Multiple
Cables
Fig. 5
1000V
Fig. 1
Not
Insulated
Insulated
Not
Insulated
Insulated
Fig. 4
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
12
Die Selection CJ22 Jaw and KA22/KC22-type
Note: These tools will provide a cUL and UL classified crimp ONLY when used with the CJ22 jaws
and KA22- or KC22-type dies.
Note: These tools will provide 53 kN (6 tons) of crimping force when used with the CJ22 jaws.
Crimps made on copper cable with Greenlee KC22-type dies and the copper connectors listed here are cUL and UL classied.
Crimps made on copper or aluminum cable with Greenlee KA22-type dies and the dual-rated aluminum connectors listed
here are cUL and UL classied.
Refer to “Connector Selection” for brand names and model numbers of appropriate lugs as well as crimping instructions.
Dies for Dual-rated Aluminum Connectors
Catalog Number UPC Number Cable Size
KA22-8 06744 8 AWG
KA22-6 06745 6 AWG
KA22-4 06746 4 AWG
KA22-2 06747 2 AWG
KA22-1 06749 1 AWG
KA22-1/0 06750 1/0 AWG
KA22-2/0 06751 2/0 AWG
KA22-3/0 06752 3/0 AWG
KA22-4/0 06753 4/0 AWG
KA22-250 06754 250 kcmil
KA22-300 06755 300 kcmil
KA22-350 06756 350 kcmil
Dies for Copper Connectors
Catalog Number UPC Number Cable Size Color Code
KC22-8 03079 8 AWG Red
KC22-6 03080 6 AWG Blue
KC22-4 03081 4 AWG Gray
KC22-2 03082 2 AWG Brown
KC22-1 03083 1 AWG Green
KC22-1/0 03084 1/0 AWG Pink
KC22-2/0 03085 2/0 AWG Black
KC22-3/0 03086 3/0 AWG Orange
KC22-4/0 03087 4/0 AWG Purple
KC22-250 03088 250 kcmil Yellow
KC22-300 03089 300 kcmil White
KC22-350 03090 350 kcmil Red
KC22-400 03091 400 kcmil Blue
KC22-500 03092 500 kcmil Brown
KC22-600B 03094 600 kcmil Green
Connector Selection
CJ22 Crimping Jaw Range: Copper — 8 AWG to 600 kcmil†; Dual-rated Aluminum — 8 AWG to 350 kcmil
When used with KC22-type dies, these tools are cUL and UL classied for use with the following connector brands:
Connector
Type
Barrel
Type
Anderson
Blackburn
®
Burndy
®
ILSCO
®
Panduit
®
T&B
®
Penn-
Union
No. of
Crimps*
Copper
Splice
Short VHSS CSP YS-L
s
CT SCSS/SCS 54504-54518 BCU
A
Long VHS CU YS
s
CTL SCL/SCH 54804-54818 BBCU
Copper
Lugs
Short VHCS CTL-2/CTL
YA-2LN/YA-L/YA-2L
YA/YA-L-TC/YA-L-2TC
CSW
CRA/CRB
LCAS/LCA
LCD
54104-54118
54204-54218
BLU
Long VHCL CTL-L/LCN YA-2N
CLN/CLW
CRA-L/CRB-L
CRA-2L/CRB-2L
LCB/LCC
54930BE-54918BE
54850BE-54876BE
BBLU
When used with KA22-type dies, these tools are cUL and UL classied for use with the following connector brands:
Connector Type
Barrel
Type
Anderson
Blackburn
®
Burndy
®
ILSCO
®
Panduit
®
** T&B
®
Penn-
Union
No. of
Crimps*
Dual-rated
Aluminum Splice
VACS ASP YS-A
AS
ASN
SA 60501-60565 PIK
B
Dual-rated
Aluminum Lugs
VACL ATL
YA-A
YA-ATN
ACL/ACN
2ACL/2ACN
ALNS/ALNN/ALND
LAA/LAB
60101-60166
60230-60267
BLUA
* Use the number of crimps listed in the last column instead of the number provided with the connector:
A — 8 to 1/0 AWG: 1 crimp B 8 to 2 AWG: 2 crimps
2/0 AWG to 600 kcmil: 2 crimps 1 to 3/0 AWG: 3 crimps
4/0 AWG to 350 kcmil: 4 crimps
** 6 AWG to 350 kcmil
500 kcmil maximum with Penn-Union connectors
s
8 AWG to 350 kcmil with Burndy copper splices
95R7
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
13
Die Installation
Installing K22, KA22, and KC22-type Dies
in CJ22 Jaw
1. Pull the die release button.
2. Slide the die into the crimping head until it "snaps"
into place.
3. Properly position the second die. Repeat step 2.
Installing W-type Dies in CJD3 Type Jaws
1. Pull the die release button.
2. Slide the die adapter (Greenlee part number
50042920) into crimping head until it "snaps" into
place.
Note: The die adapters have the "D
3
" die profile. No
additional dies are needed if the connector to be
crimped requires a "D
3
" die.
3. Repeat for the other adapter.
4. Push the W-type die detent and slide the W-type die
into place
5. Repeat step 4 to properly position the second die.
The following W-type dies may be used with the
Greenlee EK425VX Tool:
Greenlee KD6 series
Burndy W and X series
ILSCO ND seriess
Huskie HT58 series
Panduit CD-2001 series
Other industry W-type dies
Preparing Cable
Follow the lug manufacturer’s instructions for
appropriate cable strip length.
Crimping Direction
(evenly spaced)
First Compression
Crimping Direction
SIDE A
(evenly spaced)
Crimping Direction
SIDE B
(evenly spaced)
First Compression
SIDE A
First Compression
SIDE B
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
14
Operation
1. Wear appropriate Personal Protective Equipment,
including eye, face, head and arm protection and
other PPE as required by your employer, and/or as
appropriate for the job.
2. Position the crimping head over the properly
assembled connector.
3. Ensure arm's length distance between tool and user
(Fig. 3, pg. 11) then pull the trigger to make the crimp.
Note: Trigger activates white LED work light which
remains on for 10 seconds after trigger is released.
4. Hold the trigger down until the crimping tool
achieves pressure relief, which is accompanied by
an audible “pop”.
5. The ram will return automatically to the starting
position.
The process can be interrupted at any moment by
releasing the trigger. By actuating the retract button,
the ram will return to the starting position. If you do not
hear the sound of the relief valve or the ram does not
automatically retract, the crimp is not complete.
Note: This tool is not designed for continuous use. After
100 cycles allow the tool to cool for 15 minutes.
Do not twist work piece or tool during operation. Failure
could result.
* After completing the last crimp with W-type dies on an
aluminum connector, wipe off the excess oxide inhibitor.
Carrying the Tool
The carrying ring and carrying strap are for carrying
only. Never hang or suspend the tool by the strap.
Display LCD Screen Information Shown
0
1
PSI
PSI
P
P
Bluetooth
®
status, battery charge, current pressure, max. pressure. Press and hold both
buttons to change units, select with right button, and conrm by jogging the tool.
2
INFO
123456AB001
FW: 2.0
Firmware version, serialnumber
3
CURRENT USER : 1
SINGLE CLICK
MRS+
Current user. Press and hold both buttons to change user and toggle between single
click and double click operation. Change the user and operation with the right button
and conrm the selection by tapping the trigger. Selecting single click will allow the user to
operate the tool with one trigger pull. Selecting double click will require the user to press
the trigger twice within 1/2 second to operate the tool.
4
5000 OPS
Cycles and days until next service.
5
TOTAL:
T=
Q=
n=
0.0h
0.0Ah
0
Elapsed operating hours (T), Ah used (Q), and number of cycles (n) since date of
manufacture.
LCD Screen
This tool has an LCD screen that displays information
about the tool. Turn on the screen by inserting the
battery and tapping the trigger.
In normal operation, cycle through the various displays
using the left and right buttons on either side of the
screen.
The LCD screen will also display error codes in the
event of abnormal operation. See pg. 17 for error code
troubleshooting.
Bluetooth/I-Press App
This tool has Bluetooth capability that allows the tool
to communicate with the Greenlee i-press App on your
smart device.
1. Install the "i-press Klauke Software Solutions"
app from the App Store or Google Play. Open
the app on your smart device and select the
Greenlee option.
2. Switch on the Bluetooth function on your smart
device and activate the tool to establish a
connection.
3. The app will allow you to create projects,
personalize your tool, and display tool pressure
readings, battery charge, the last service date, and
more. Instructions how to use the app are shown in
the i-press app itself; alternately, request MA6864
brochure from any Greenlee distributor.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
15
Service and Maintenance
If damage to tool's housing or Tri-Barrier Insulation
Collar is observed or suspected, or if hydraulic oil has
leaked from the tool, do not use the tool. Tool safety
could be compromised. Return tool immediately to
Greenlee at 800-435-0786 for warranty service or repair.
Proper maintenance of the tool including periodic
replacement of the tool's Tri-Barrier Insulation Collar
componentry is required.
On the earlier of either 2 years or 5,000 cycles, Factory
Service of the tool must be completed. Factory
Service includes replacement of tool's di-electric
hydraulic oil, replacement of tool's Tri-Barrier Insulation
Collar componentry and di-electric testing of tool
by trained technicians as well as general review of
mechanical function.
The Tri-Barrier Insulation Collar componentry on the
tool must be replaced every
two years. Failure to follow
the required Factory Service
schedule could compromise the
insulating properties of the tool
and result in serious injury.
The tool will alert when the
earlier of either 2 years or
5,000 cycles is approaching and will alert again when
Factory Service is required. When Factory Service date
is approaching or arrived, contact Greenlee Customer
Service. Expedited shipping is available. After contacting
Greenlee Customer Service, the tool should be sent to
the Greenlee Factory Service Center at 4411 Boeing Dr.,
Rockford, IL 61109.
Use this schedule to help track when your tool is due in
for Factory Service.
To avoid tool damage or compromise of the tool's
insulation barriers: clean the housing with a damp cloth
and mild detergent after every use. Dry completely and
fully retract the ram. Place the tool in the carrying case
and store in a cool dry place. Do not use the carrying
strap to hang or suspend tool. Avoid dropping the
Storage and Cleaning
tool. If necessary, recharge the batteries. Refer to the
instructions supplied with the battery charger. Store tool
in proper manufacturer provided protective enclosure.
Keep this manual with the tool.
Routine Service Calendar Service Date Notes
Date Placed into Service
Date of First Factory Service
Date of Second Factory Service
Date of Third Factory Service
Date of Fourth Factory Service
Date of Fifth Factory Service
Date of Sixth Factory Service
Date of Seventh Factory Service
Date of Eighth Factory Service
Date of Ninth Factory Service
Date of Tenth Factory Service
Date of Eleventh Factory Service
Do not perform any service or maintenance other
than as described in this manual. Personal injury or
damage to the tool may result.
The Tri-Barrier Insulating componentry must be
replaced by Greenlee factory technicians every
two years. Failure to replace Tri-Barrier Insulating
componentry may result in personal injury or damage.
Tri-Barrier
Insulation
Collar
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
16
Problem Possible Cause Probable Remedy
Tool is inoperative. Dirt, contaminants, etc., in
ram area oftool.
Clean tool.
Tool components worn or
damaged.
Contact Greenlee Customer Service at
800-435-0786 for warranty service or repair.
Motor is inoperative. Low or uncharged battery. Try known charged battery. Inoperative battery may be
discharged or may have reached life expectancy.
Broken switch components. Contact Greenlee Customer Service at
800-435-0786 for warranty service or repair.
Motor runs but tool will
not complete a cycle.
Oil level low. Contact Greenlee Customer Service at
800-435-0786 for warranty service or repair.
Air in hydraulic system. Pull trigger and hold retract button simultaneously.
Run for approximately 10 seconds, and then attempt
to cycle the tool. If unsuccessful, contact Greenlee
Customer Service at 800-435-0786 for warranty
service or repair.
Cold oil. Pull trigger and hold retract button simultaneously to
warm oil. Store tool in warm area.
Tool loses oil. Damaged seal. Contact Greenlee Customer Service at
800-435-0786 for warranty service or repair.
Troubleshooting
Before You Begin
1. Make sure that the battery is charged. Recheck
the battery after several minutes to make sure the
battery is holding its charge.
2. Use a nonflammable contact cleaner or pencil
eraser to clean the electrical contacts on the battery
and tool.
3. Reinstall the battery and check the tool again.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
17
LED Indicator (red)
This tool is equipped with a special circuit board
incorporating several important features to inform
the user about the current status of the unit. The LED
signals in the following cases:
What happens Signal What it means
What to
do
Tool will not start,
and constant light for
20seconds when trigger
is released
Battery
charge low
Change
or charge
battery
Tool will stop, and
constant light for
20seconds after trigger
is released
Tool will stop, and
flashing light for
20seconds when
trigger is released
Motor current
exceeds 20A
during cycle
Let tool
cool
Circuit has
become too hot
Flashing light for 20
seconds at end of cycle
and
audible
warning
Indicates 4,750
cycles exceeded
or 21 months
exceeded
Send tool
in for
service
Error
Code
Meaning Action
1 Overcurrent fuse Seek Service
2 Overcurrent comparator Seek Service
3 Overheated circuit board Cool Tool
4 Overheated battery Cool Battery
5
Battery empty; operation
stops
Charge Battery
6
Faulty crimp; complete
cycle
Seek Service
7
Faulty crimp; incomplete
cycle
Seek Service
8 Low battery Charge Battery
9 Battery empty Charge Battery
10
Real-time clock battery
low
Seek Service
11 Tool deactivated Seek Service
12 Service necessary Seek Service
13
Real-time clock not
found
1. Re-insert Battery
2. Seek Service
14 Bluetooth
®
unit not found
1. Re-insert Battery
2. Seek Service
15 [Not Used]
16
Pressure sensor not
found
Seek Service
17 Burst pressure exceeded Seek Service
18
Battery temperature too
low
Warm Battery
19
Blinking Screen 4,750
cycles exceeded
Seek Service
If certain problems arise with the tool, an error code
appears on the LCD screen (see pg. 14).
Troubleshooting (cont'd)
Note: The tool will indicate when re-certication is near.
Starting at 4,750 cycles or 21 months (whichever occurs
rst), the red LED and work LED will ash, an audible
warning will sound, and the LED will display SERVICE
NECESSARY for 20 seconds after every cycle. After
5,000 cycles or 2 years, the tool will not operate unless
the battery is removed and reinstalled. Only one cycle is
possible each time the battery is reinstalled.
Gator
®
Insulated Battery-Powered In-Line Crimpers
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
18
Model X—FCC ID: RFR-S50; IC ID:
4957A-S50
USA requirements:
Responsible party: Greenlee Tools, Inc.
Rockford, IL 61109 USA
Note: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio com-
munications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case
the user will be required to correct the interference at
his own expense.
This device complies with the RF exposure SAR
test exclusion requirements for portable devices, if a
minimum separation distance is kept. However, the
device shall be used in such a manner that the potential
for human contact during normal operation is minimized.
Canada requirements:
This device complies with Industry Canada’s license-
exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions
suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est suscep-
tible d’en compromettre le fonctionnement.
Warranty
Model "VX" insulated tools are covered by the standard
Greenlee Limited Warranty for a period of 7 years, this
limited warranty excludes coverage for the Tri-Barrier
Insulation Collar and componentry.
The Tri-Barrier Insulation Collar and componentry are
covered by the standard Greenlee Limited Warranty for
a period of 2 years.
To review the standard Greenlee Limited Warranty, visit
www.greenlee.com.
Do not perform any service or maintenance other
than as described in this manual. Personal injury or
damage to the tool may result.
The Tri-Barrier Insulating componentry must be
replaced by the factory every two years. Failure to
replace may result in personal injury or damage.
For warranty claims and/or factory service please
contact Greenlee Customer Service by phone at
800-435-0786.
Shipping address:
Greenlee Factory Service Center
4411 Boeing Dr., Rockford, IL 61109
Reminder: Warranty claim is void if warranty seal on tool
is broken.
19
4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070
©2019 Greenlee Tools, Inc. • An ISO 9001 Company
USA Tel: 800-435-0786
Fax: 800-451-2632
Canada Tel: 800-435-0786
Fax: 800-524-2853
International Tel: +1-815-397-7070
Fax: +1-815-397-9247
www.greenlee.com
Gator
®
Insulated Battery-powered In-line Crimper
20
MANUAL DE FUNCIONAMIENTO
Engarzadora GATOR
®
aislada accionada
porbatería
52087647 © 2019 Greenlee Tools, Inc. 10/19
Lea y comprenda todas las instrucciones y la
información de seguridad de este manual antes
de utilizar esta herramienta.
GUARDE ESTE MANUAL
EK425VX
EK628VX
Registrar el número de
serie aquí
_______________________
(Consulte la pág. 14 para
ver las instrucciones de la
pantalla LCD)
E114954
REG F770
1000V
95R7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Greenlee 52087647 REV0 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur