MartinLogan Mikros 70 Manuel utilisateur

Marque: MartinLogan

Modèle: Mikros 70

Taper: Manuel utilisateur

IMPORTANT SAFETY AND OPERATING INSTRUCTIONS.

PLEASE READ BEFORE USING YOUR EARPHONES.

Before inserting earphones into the ear canal, set volume to the lowest level then

gradually increase until desired volume level is reached. • Avoid listening at high

volume levels for long periods of time. Noise levels are measured in decibels (dB).

Regular exposure to noise at or above 85dB can cause hearing loss. Monitor your

listening as hearing loss happens over time. Refer to the guidelines on the Consum-

er Electronics Association’s website relating to safe listening levels: http://www.

ce.org/PDF/ListenLifetime_spread.pdf • Do not use earphones at

times when your attention is required—such as driving, operating heavy machin-

ery, bicycling, or jogging. It is dangerous and in many jurisdictions illegal to drive

wearing noise-isolating earphones because it dramatically decreases your chance

of hearing life saving sounds around you such as car horns or emergency sirens.

• Flying at high altitudes may cause pressure build up in your ears. While

in-flight, remove earphones periodically to relieve pressure. • This product

generates strong permanent magnetic fields that could cause interference

with cardiac pacemakers and implanted defibrillators (ICDs). Maintain a dis-

tance of at least 4-inches (10cm) between the earphones and the medical

device. • Do not expose product to heat (hair dryer, radiators, etc.) and do

not store in direct sunlight for extended periods of time. • Protect product

from moisture. • In rare instance an ear tip may come off in the ear ca-

nal when removing the earphones. If this should occur and the ear tip can-

not be easily removed, it is recommended that you promptly contact a medical

professional. A professional can use blunt tweezers to remove the ear tip. •

Consult a medical professional if you have excessive ear wax, difficulty insert-

ing the ear tips, or discomfort after prolonged use. • Avoid dropping and

strong impact. • Do not use in-ear earphones without a proper ear tip.

• Do not pull the cord to remove the earphones from the ear or from the audio

device. • Clean or replace ear tips prior to use by other persons.

CONTENTS

(1) Earphone with remote

(3) Bulb ear tips (small, medium, large)

(2) Flange ear tips (small, large)

(1) Travel case

(1) Manual

SELECTING AND INSERTING EAR TIPS

Select an ear tip that fits comfortably and forms a good seal in your ear canals.

Tips should fit snugly but not tightly. When properly inserted, with the volume

down, you should not be able to easily hear nearby people talking. With the

volume up, you should have good sound quality with deep, extended bass.

Carefully insert tips by pushing them into place. Some users may find it easiest to

insert by pulling up on the back of the ear. Other users may find a slow twisting

motion aides with insertion.

The earphone with an ‘R’ is for the right ear. The earphone with an ‘L’ is for the left

ear. You can also use the red/white colored ear tips to quickly distinguish between

the right and left earphone. We recommend always putting the red ear tip on the

right earphone.

REMOVING EAR TIPS

Never remove the earphones by pulling the cord. Remove by grasping the body of

the earphone between your fingers and slowly pulling out until the seal is broken.

Some users may find that a slow twisting motion will ease removal.

ADJUSTING THE CABLE SLIDER

A cable slider is included to help assure a comfortable fit and reduce tangles. The

cable slider is located immediately above the area where the cord splits and can

slide up and down the cord to customize fit. To reduce tangles we recommend

positioning the slider at top of the cord near the remote when in storage.

REMOTE: AUDIO FUNCTIONS (SELECT APPLE PRODUCTS)*

Volume up/down press top button/press bottom button

Play/pause press middle button

Next track press middle button two times (rapidly)

Previous track** press middle button three times (rapidly)**

Voice control press and hold middle button for two seconds when

the iPhone, iPod, or iPad home screen is displayed

REMOTE: PHONE FUNCTIONS (SELECT APPLE PRODUCTS)*

Answer/end call press middle button

Reject call press and hold middle button for two seconds

*The remote and mic are supported only by iPod nano (4th, 5th, and 6th generation), iPod classic, iPod touch

(2nd, 3rd, and 4th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPad (3rd generation), iPad 2, and iPad.

The remote is supported by iPod shuffle (3rd and 4th generation). Audio is supported by all iPod models.

**Pressing the middle button three times will go to beginning of the current track. Pressing the

middle button three times during the first few seconds of a track will go to the previous track.

MICROPHONE AND REMOTE (NON-APPLE PRODUCTS)

The earphones will play audio from any source with a standard 3.5mm 3-conductor

(stereo headphone) socket. The microphone will function with most smart phones

and similar devices with a standard 3.5mm 4-conductor socket (stereo headphone

+ microphone). The remote control will function with some non-Apple smart

phones, digital media players, and similar devices. Exact functions of the remote

will vary by make and model and MartinLogan cannot guarantee compatibility with

specific brands or models.

BREAK IN

Allow approximately 15–30 hours of break in at moderate listening levels before

any critical listening. Like most high-performance audio reproduction devices, a

break-in period should result in improved performance. For rapid break-in you may

choose to leave the earphones connected to an audio source playing music during

the night or when otherwise not in use.

CLEANING

To clean the earphones lightly wipe the ear

piece and cord with a slightly damp cloth. If

the ear tips become clogged, remove the

ear tips and gently squeeze the clog out of

the ear tip shaft or extract using a pin. Never

attempt to remove clogs while the ear tips are

installed on the earphone. Never get the

earphones wet. Never use solvents and other

harsh cleaning products as they will perma-

nently damage the earphones.

SPECIFICATIONS (subject to change without notice)

Frequency response . . .8–19,000 Hz

Impedance . . . . . . . . . . .22 Ohms

Maximum output. . . . . .111.46dB SPL

Sensitivity. . . . . . . . . . . .98dB (at 1kHz with 1mW input)

Max input power. . . . . .20mW

Transducer . . . . . . . . . . .6.6mm dynamic driver

Noise isolation . . . . . . .97.8% (-33dB SPL, at 1kHz with 1mW input, 30cm)

Weight. . . . . . . . . . . . . . .13.4g (0.5oz.)

Connector . . . . . . . . . . . .

Right angle gold-plated 3.5mm (1/8”) 4-conductor plug

Cord. . . . . . . . . . . . . . . . .4 foot (1.2m) cable

SPECIFICATIONS: MICROPHONE (subject to change without notice)

Frequency response . . .180Hz–10kHz (-5dB; 3dB)

Pickup pattern. . . . . . . .Omnidirectional

Sensitivity. . . . . . . . . . . .-42dB (as per 121 R 9-5)

PROBLEMS WITH YOUR EARPHONES?

Please do not return earphones to the retailer. Contact MartinLogan customer service

directly at (785) 749-0133 or email [email protected].

WARRANTY

MartinLogan warrants this product against defects in materials and workmanship

under normal use and operation for a period of one (1) year from the date of retail

purchase by the original end-user purchaser. Maintain your original sales receipt

for proof of purchase. For complete warranty information visit our website at www.

martinlogan.com/warranty.

DECLARATION OF CONFORMITY

This product is in compliance with the essential requirements and

other relevant provisions of directives: EMC 2004/108/EC, RoHS 202/95/EC,

WEEE 202/96/EC.

EUROPEAN RECYCLING AND REUSE GUIDELINES

In accordance with the European Union WEEE (Waste Electrical and

Electronic Equipment) directive effective August 13, 2005, we would like to

notify you that this product may contain regulated materials which upon disposal,

according to the WEEE directive, require special reuse and recycling processing.

For this reason Martin Logan has arranged with our distributors in European Union

member nations to collect and recycle this product at no cost to you. To find your

local distributor please contact the dealer from whom you purchased this product,

email [email protected] or visit the distributor locator at www.martinlogan.com.

Please note, only this product itself falls under the WEEE directive. When disposing

of packaging and other related shipping materials we encourage you to recycle

these items through the normal channels.

iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple

Inc., registered in the U.S. and other countries.

The remote and mic are supported only by iPod nano (4th, 5th, and 6th generation), iPod classic, iPod touch

(2nd, 3rd, and 4th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPad (3rd generation), iPad 2, and iPad.

The remote is supported by iPod shuffle (3rd and 4th generation). Audio is supported by all iPod models.

“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean that an electronic accessory

has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been

certified by the developer to meet Apple performance standards. Apple is not responsible for the

operation of this device or its compliance with safety and regulatory standards. Please note that

the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.

www.martinlogan.com

rev. 061112

Inspired by the clarity and detail

of MartinLogan’s legendary

high-end electrostatic loudspeakers.

DIRECTIVES IMPORTANTES EN MATIÈRE DE SÉCURITÉ

ET D’UTILISATION. VEUILLEZ LIRE CE QUI SUIT AVANT

D’UTILISER VOS ÉCOUTEURS.

Avant d’insérer les écouteurs dans le canal auditif, réglez le volume au plus bas, puis augmentez-le

graduellement jusqu’à l’obtention du volume souhaité. • Évitez l’écoute à des volumes élevés

pendant de longues périodes. Les niveaux sonores sont mesurés en décibels (dB). L’exposition ré-

gulière à un bruit de 85dB ou plus peut causer une perte de l’audition. Surveillez le niveau sonore,

car la perte de l’audition survient au fil du temps. Consultez les lignes directrices du site Web de

la Consumer Electronics Association concernant les niveaux sonores sécuritaires : http://www.

ce.org/PDF/ListenLifetime_spread.pdf • N’utilisez pas les écouteurs lorsque votre at-

tention est requise, comme lorsque vous conduisez, lorsque vous opérez de la machinerie lourde,

ou lorsque vous faites de la bicyclette ou du jogging. Cela est dangereux et dans certains territoires,

il est illégal de conduire en portant des écouteurs à isolation sonore, car ceux-ci diminuent de façon

importante la possibilité d’entendre des sons ambiants pouvant vous sauver la vie, comme des

klaxons ou des sirènes. • Le vol en haute altitude peut entraîner une accumulation de pression

dans vos oreilles. En vol, enlevez les écouteurs de façon périodique pour relâcher la pression.

• Ce produit génère des champs magnétiques permanents puissants qui pourraient causer une

interférence avec les stimulateurs cardiaques et les défibrillateurs (ICD). Gardez une distance d’au

moins 4 po (10cm cm) entre l’écouteur et le dispositif médical. • N’exposez pas le produit à la

chaleur (séchoir à cheveux, radiateur, etc.) et ne l’entreposez pas directement dans les rayons du

soleil pendant de longues périodes. • Protégez le produit de l’humidité. • Dans de rares cas,

un embout peut rester logé dans le canal auditif lorsque vous retirez l’écouteur. Si cette situation se

produit et que l’embout ne peut pas être retiré facilement, il est recommandé de consulter rapide-

ment un professionnel de la santé. Un professionnel peut utiliser des pincettes pour retirer l’embout.

• Consultez un professionnel de la santé si vous avez trop de cire d’oreille, si vous avez de la dif-

ficulté à insérer les embouts ou si vous ressentez de l’inconfort après une utilisation prolongée. •

Évitez de laisser tomber les écouteurs et les impacts forts. • N’utilisez pas d’écouteurs dans l’oreille

sans embouts appropriés . • Ne tirez pas sur le cordon pour enlever les écouteurs de l’oreille ou d’un

appareil audio. • Nettoyez ou remplacez les embouts avant l’utilisation par d’autres personnes.

CONTENU

(1) Écouteur avec télécommande

(3) Embouts bombés (petit, moyen, grand)

(2) Embouts à bride (petit, grand)

(1) Étui de voyage

(1) Manuel

CHOIX ET INSERTION DES EMBOUTS

Choisissez un embout qui s’ajuste confortablement et qui scelle bien le canal auditif. Les em-

bouts doivent se fixer de façon confortable, mais ne doivent pas être serrés. Lorsqu’ils sont bien

insérés, et que le volume est au plus bas, vous ne devriez pas entendre facilement des gens qui

parlent à proximité. Avec le volume, vous devriez obtenir une bonne qualité sonore avec des

graves profondes et étendues. Insérez les embouts avec soin en les poussant en place. Certains

utilisateurs trouvent qu’ils s’insèrent plus facilement en poussant vers le haut la partie arrière de

l’oreille. D’autres utilisateurs préfèrent utiliser un mouvement de rotation lent pour l’insertion.

L’écouteur avec la lettre « R » est pour l’oreille droite. L’écouteur avec la lettre « L » est pour

l’oreille gauche. Vous pouvez également utiliser les embouts de couleur rouge/blanche pour

distinguer rapidement l’écouteur de gauche et de droite. Nous vous recommandons de toujours

placer l’embout rouge sur l’écouteur de droite.

ENLEVER LES EMBOUTS

Ne jamais enlever les écouteurs en tirant sur le cordon. Enlevez l’embout en saisissant le

corps de l’écouteur entre vos doigts et en tirant délicatement jusqu’à ce que le sceau se défasse.

Certains utilisateurs utilisent un lent mouvement de rotation pour faciliter le retrait.

RAJUSTER LA GLISSIÈRE DU CORDON

Une glissière de câble est incluse et permet un ajustement confortable qui réduit les emmêlements. La

glissière de câble se trouve juste au-dessus de l’endroit où le cordon se sépare; elle remonte ou descend

le long du câble pour un ajustement confortable. Pour réduire les emmêlements, nous recommandons de

placer la glissière dans la partie supérieure du cordon, près de la télécommande, lors de l’entreposage.

La page est en cours de chargement...

MartinLogan Mikros 70 Manuel utilisateur

Marque: MartinLogan

Modèle: Mikros 70

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: MartinLogan Mikros 70 User manual

MartinLogan Mikros 70 Manuel utilisateur

MartinLogan Mikros 70 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents