Datalogic Heron D110 Guide de référence
- Catégorie
- Lecteurs de codes à barres
- Taper
- Guide de référence
Heron
D110 SERIES READERS
For IBM 46xx Terminals
QUICK REFERENCE
GUIDA RAPIDA
GUIDE RAPIDE
KURZANLEITUNG
GUÍA RÁPIDA
820001231 (Rev. A)
USING HERON™ SERIES READERS
UK
Heron guns automatically scan barcodes at a distance.
Simply aim and pull the trigger. Code scanning is performed
along the center of the light bar emitted from the reading
window. This bar must cover the entire code.
Successful scanning is obtained by tilting the scanner with
respect to the barcode to avoid direct reflections which impair
the reading performance, see the figure above.
Successful reading is signaled by an audible tone plus a good-
read green spot.
By correctly inserting the reader into its stand, it is immediately
ready to read automatically any code present in its reading area
without pressing the trigger. Furthermore, a green aiming light
is continuously emitted to facilitate the positioning of the
barcode to be read, see the figure above. To guarantee single
code reading, same code consecutive reading requires the
code to be removed from the reading area (no decoding) before
the reader will accept the same code.
I
Con le pistole Heron la lettura dei codici a barre avviene a
distanza: è sufficiente mirare sul codice e premere il grilletto.
La finestra anteriore proietta una banda luminosa che deve
essere centrata sul codice e attraversarlo interamente. Le
condizioni ottimali per la lettura si ottengono quando la pistola
viene usata con un'inclinazione rispetto al piano su cui si trova
il codice, così da evitare il rischio di riflessione diretta, che
potrebbe compromettere il risultato della lettura (vedi figura).
La buona lettura è segnalata da un beep sonoro e da uno spot
verde che illumina il codice.
Inserendo correttamente la pistola nello stand, questa sarà
immediatamente pronta per leggere automaticamente i codici
presenti nella sua area di lettura senza premere il grilletto.
Inoltre, un puntatore di luce verde verrà attivato per facilitare il
posizionamento del codice da leggere, (vedi figura).
La singola lettura di un codice viene garantita dal fatto che una
lettura consecutiva dello stesso codice richiede la sua
rimozione dell’area di lettura (nessuna decodifica) prima di
essere nuovamente accettato dal lettore.
F
Avec les pistolets Heron, la lecture des codes s'effectue
automatiquement et à distance. Il suffit de viser le code et
d’appuyer sur la gâchette. Le faisceau sortant de la fenêtre de
lecture de l'appareil lit le code. Ce faisceau doit être centré sur
le code à barres à lire et doit le traverser de part en part.
Pour des prestations optimales inclinez la douchette par
rapport au code à lire, afin d'éviter des réflexions directes qui
pourraient compromettre la performance de lecture (voir figure
ci-dessus).
La lecture correcte est signalée par un beep sonore ainsi que
par un spot vert qui illumine le code lu.
Après une introduction correcte du pistolet dans le support, le
pistolet est prêt à lire automatiquement les codes qui se
trouvent dans la zone de lecture sans appuyer sur la gâchette.
Le pistolet déclenche également un pointeur lumineux vert qui
facilite le positionnement du code à lire (voir figure).
Une seule lecture du même code est garantie puisque pour lire
deux fois le même code, il faut déplacer le code hors de la
zone de lecture (aucune lecture) avant qu’il soit lu par le lecteur
une deuxième fois.
D
Die Heron Lesepistolen lesen Strichcodes automatisch und
berührungslos. Es genügt auf den Code zu zielen und die
Taste zu drücken. Der Code wird mittels eines Lichtbandes
gelesen, das das Gerät durch das Lesefenster verlässt. Dieses
Lichtband muß den gesamten Code möglichst in der Mitte
durchqueren.
Eine optimale Lesung ist gewährleistet, wenn der Benutzer die
Pistole bzgl. der Oberfläche, auf der sich der Code befindet,
etwas neigt, um eine direkte Reflexion zu vermeiden, wie im
Bild oben gezeigt wird.
Das erfolgreiche Lesen wird durch einen "Beeper" und einen
grünen Lichtpunkt angezeigt.
Wenn die Pistole im Halter korrekt positioniert wird, ist Sie
sofort bereit Codes automatisch (ohne Tastendruck) zu lesen.
Außerdem, verlässt die Pistole einen grünen Lichtpunkt, der
eine einfache Positionierung des Codes ermöglicht (siehe Bild).
Um eine einzige Lesung des Codes zu garantieren, erfordert
die Doppellesung den Code vom Lesefenster (kein
Dekodierung) zu entfernen. Dann positionieren Sie denselben
Code für eine neue Lesung zurück.
E
Los lectores Heron™ capturan automáticamente códigos de
barras a distancia: sólo hay que encuadrar el código y apretar
el gatillo. La lectura se realiza sobre el rayo de luz emitida por
la ventana de lectura que debe atravesar el código de parte a
parte.
Las condiciones óptimas para la lectura se obtienen inclinando
el escáner respecto al código de barras para evitar reflexiones
directas de luz que podrían perjudicar el rendimiento de lectura
(ver figura arriba). El lector señala una lectura correcta a través
de un pitido y de un punto verde.
Insertándolo correctamente en su mostrador, el lector estará
listo de forma inmediata para leer automáticamente cualquier
código en su área de lectura sin apretar el gatillo. Además, el
lector emite siempre una luz verde que facilita el encuadre del
código (ver figura arriba). Para evitar que el mismo código sea
leído varias veces, para efectuar lecturas consecutivas del
mismo código es necesario quitar el código del área de lectura
(no decodificación) y volverlo a presentar al lector para que
éste lo pueda aceptar otra vez.
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
Heron D1XX
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista
siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità
elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic
compatibility and product safety.
Basée sur la législation des Etates membres relative à la compatibilité
électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf
elektromagnetische Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la
compatibilidad electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022, August 1994: L
IMITS AND METHODS OF MEASUREMENTS OF
RADIO DISTURBANCE OF INFORMATION
TECHNOLOGY EQUIPMENT
(ITE)
EN 50024, September 1998: I
NFORMATION
T
ECHNOLOGY
E
QUIPMENT
.
I
MMUNITY CHARACTERISTICS
. L
IMITS AND
METHODS OF MEASUREMENTS
Lippo di Calderara, 06/02/2004 Ruggero Cacioppo
Quality Assurance Laboratory Manager
SERVICES AND SUPPORT
UK
Datalogic provides several services as well as
technical support through its website. Log on to
www.datalogic.com/services and click on the links
indicated for further information including:
I
Datalogic fornisce servizi e supporto tecnico tramite
il suo sito web. Connettersi al sito
www.datalogic.com/services e cliccare sui link
indicati per avere ulteriori informazioni, come
elencato di seguito:
F
Datalogic fournit différents services et une aide
technique en ligne. Connectez-vous sur
www.datalogic.com/services et cliquez sur le lien
indiqué pour obtenir des informations
complémentaires sur:
D
Datalogic bietet unterschiedliche Service-
Leistungen, wie auch technische Unterstützung über
Internetseiten. Gehen Sie auf die Seite
www.datalogic.com/services und klicken Sie auf
die Links
die Sie über folgende Punkte informieren:
E
Datalogic proporciona servicios y soporte técnico a
través su página web. Hay que conectarse a
www.datalogic.com/services y hacer clic en los
enlaces
indicados a continuación para recibir más
información:
• Datalogic Services
- Warranty Extensions and
Maintenance Agreements
• Downloads
- Software Downloads, Manuals and
Catalogues
• Contact Us
- Listing of Datalogic Subsidiaries and
Quality Partners
• Authorised Repair Centres
• Products
>Hand-Held Readers >Software Tools - DL
Sm@rtSet™
DL Sm@rtSet™ is a Windows-based utility program
which allows device configuration using a PC. It provides
RS232 interface configuration as well as configuration
barcode printing.
CONNECTIONS
RS232
With the RS232 cable, this accessory device is intended to be
supplied by a UL Listed or CSA Certified Direct Plug-in Power
Unit marked "Class 2", rated 5 V, minimum 180 mA.
IBM port 9B / IBM port 5B
With the IBM terminal 5B and 9B port cables, this accessory
device is intended to be connected to a UL Listed or CSA
Certified Computer which supplies power directly to the reader.
DISCONNECTING THE CABLE
STAND INSTALLATION
UK
The stand can be mounted by using self-tapping screws,
double sided adhesive strips or rubber feet:
A) mount the stand directly to the surface using the
self-tapping screws;
B) carefully clean the bottom surface of the stand and the
table surface. Remove the protective plastic from one side
of the adhesive strips and stick them on the stand bottom.
Then, remove the plastic from the other side of the strips
and affix the stand to the table;
C) carefully clean the bottom surface of the stand, remove the
protective film from the rubber feet and stick them in the
corresponding housing on the bottom surface. It is also
possible to fix an optional metal plate.
I
Lo stand può essere montato utilizzando le viti autofilettanti, le
strisce adesive oppure i piedini di gomma:
A) montare lo stand direttamente sulla superficie utilizzando le
viti autofilettanti;
B) pulire accuratamente la superficie inferiore della base dello
stand e la superficie d’appoggio. Togliere la plastica
protettiva da un lato di ogni striscia e attaccare entrambe le
strisce alla base dello stand. Rimuovere la plastica
protettiva dall’altro lato delle strisce adesive e attaccare lo
stand alla superficie d’appoggio;
C) pulire accuratamente la superficie inferiore della base dello
stand, quindi togliere la pellicola protettiva dai piedini e
attaccarli all’interno delle apposite sedi nella base di
plastica. Inoltre, è possibile fissare un base metallica
opzionale.
WARRANTY
UK
Datalogic warranties this product against defects in
workmanship and materials, for a period of 5 years
from the date of shipment, provided that the product
is operated under normal and proper conditions.
Datalogic has the faculty to repair or replace the
product, these provisions do not prolong the original
warranty term.
The warranty does not apply to any product that has
been subject to misuse, accidental damage,
unauthorized repair or tampering.
I
Datalogic garantisce questo prodotto contro difetti di
fabbricazione e di materiali per 5 anni dalla data di
consegna, a condizione che il prodotto sia utilizzato
come previsto.
Datalogic si riserva la facoltà di riparare o sostituire il
prodotto. Quanto sopra non prolunga la garanzia
originale.
La garanzia non si applica a prodotti utilizzati in modo
non corretto, danneggiati accidentalmente, sottoposti
a riparazioni non autorizzate o manomessi.
F
Datalogic garantit ce produit de tout défaut de
fabrication ou des matériaux pendant 5 ans à compter
de la date de livraison, à condition que le produit soit
utilisé correctement.
Datalogic a la faculté de réparer ou de remplacer ce
produit. Ces mesures ne prolongeront pas l’échéance
de la garantie.
La garantie ne s’applique pas aux produits qui ont été
utilisés de façon incorrecte, accidentellement
endommagés, soumis à des réparations non
autorisées ou bien altérés.
D
Datalogic gibt für dieses Produkt eine Garantie von 5
Jahren auf Herstellungs- und Materialfehler ab
Versandsdatum, falls das Produkt unter normalen und
angemessenen Bedingungen verwendet wurde.
Datalogic behält sich vor, das Produkt entweder zu
reparieren oder zu ersetzen, was aber den originalen
Garantietermin nicht verlängert.
Die Garantie erlischt bei unsachgemäßer Verwendung
und unberechtigter Veränderungen am Produkt.
E
Datalogic garantiza este producto contra todos los
defectos de fabricación y materiales por un periodo
de 5 años desde la fecha de envío, a condición de
que el producto sea utilizado en condiciones
normales y correctas.
Datalogic tiene el derecho de reparar o reemplazar el
producto sin que esto suponga una prolongación de
la garantía original.
La garantía no será valida si el producto ha sufrido
abusos, daños accidentales, reparaciones no
autorizadas o ha sido falsificado.
A
B
C
LED CLASS
R
CUS
SEE PACKAGE FOR
PATENT LISTING
UK
Class 1 LED product
I
Apparecchio LED classe 1
F
Appareil à LED de classe 1
D
LED Klasse 1
E
LED Clase 1
This product conforms to EN60825-1:2001.
PATENTS
This product is licensed by one or more of the following U.S.
patents:
4,894,523; 5,021,642; and 6,158,661
This product is covered by one or more of the following patents:
U.S. patents 5,992,740; 6,305,606 B1; 6,631,846 B2;
6,517,003 B2; and 6,712,271 B2
European patents 851,378 B1; 895,175 B1; 962,880 B1;
997,760 B1; and 1,128,315 B1
Additional patents pending.
F
Pour le montage du support il est possible également d’utiliser
des vis filetées, des bandes adhésives ou des petits patins en
caoutchouc:
A) utiliser des vis filetées pour le montage sur la surface
d’appui;
B) nettoyer soigneusement la surface inférieure du support et
la surface d’appui.
Retirer le plastique protecteur de l’une
des faces des bandes et la coller sur la surface inférieure
du support. Retirer le plastique protecteur sur l’autre face
adhésive et coller le support sur la surface d’appui ;
C) nettoyer soigneusement la surface inférieure du support.
Retirer la pellicule protectrice des patins et coller les patins
dans les logements correspondants situés sur la surface
inférieure du support. Il est possible aussi de fixer une
plaque métallique en option.
D
Der Halter kann mittels der selbstschneidenden Schrauben, der
Klebstreifen oder mittels der Gummifüßchen befestigt werden:
A) für eine permanente Installation verwenden Sie die zwei
selbstschneidenden Schrauben.
B) die untere Seite des Halters und die Ablagefläche sorgfältig
reinigen. Die Schutzschicht von einer Seite jedes
Klebstreifens entfernen und beide Klebstreifen auf den
Halters kleben. Die Schutzschicht von der anderen Seite
der Klebstreifen entfernen und den Halter auf der
Ablagefläche befestigen.
C) die untere Seite des Halters und die Ablagefläche sorgfältig
reinigen um die Füßchen auf die Sitzen des Halters zu
kleben. Man kann auch eine optionale Metallunterlage
befestigen.
E
El soporte puede ser montado a través de tornillos auto-
bloqueantes (A), tiras adhesivas de doble cara (B) o pies de
goma (C):
A) Montar el soporte directamente sobre la superficie
utilizando los tornillos auto-bloqueantes;
B) Limpiar con cuidado la superficie inferior del soporte y la
superficie de la mesa. Quitar el plástico de protección de
una de las caras de las tiras adhesivas y pegarla a la
superficie inferior del soporte. Luego quitar el plástico de la
otra cara de la tira adhesiva y posicionar el soporte en la
posición deseada sobre la mesa;
C) Limpiar con cuidado la superficie inferior del soporte, quitar
el plástico de protección de los pies de goma e insertarlos
en las posiciones correspondientes en la superficie inferior
del soporte. Es posible también fijar una placa de metal
opcional.
INSERTION INTO STAND
UK
Pair the reader to the stand paying attention to
insert the handle into the stand clip (see figure
above). Correct insertion will be signaled by a
beep; the reader will then be ready to read
barcodes.
I
Posizionare la pistola nello stand assicurandosi
che il manico sia inserito nel fermo dello stand
stesso (vedi figura sopra). Un beep sonoro
segnalerà il corretto inserimento ed il lettore sarà
pronto per leggere i codici a barre.
F
Placer le pistolet dans le support en faisant
attention d’introduire la poignée dans le crochet du
support (voir figure ci-dessus). Un beep sonore
indiquera un positionnement correct. Le pistolet
est ainsi prêt à lire les codes.
D
Positionieren Sie die Pistole im Halter und stecken
Sie den Griff in die Öffnung des Halters (siehe Bild
oben). Das korrekte Positionieren wird durch einen
Piepton angezeigt. Dann ist die Pistole bereit
Codes zu lesen.
E
Poner el lector en su soporte insertando la
empuñadura en el clip del soporte (ver figura
arriba). El soporte emitirá un pitido al insertar el
lector de forma correcta. El lector estará entonces
listo para leer códigos de barras.
READING DIAGRAM
0
5
10
15
20
25
30
35
-15
-10
-5
0
5
10
15
D110 - Reading Zones (10° skew angle)
(cm)
CODE 39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE 39
0.50 mm
(20 mils)
0.13 mm
(5 mils)
FCC COMPLIANCE
This device complies with PART 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference which
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
TECHNICAL FEATURES
Heron
D110
Electrical Features
Power Supply
RS232 interface
IBM 46xx
5 Vdc ± 5%
12 Vdc directly taken from cash
register
RS232 IBM 46xx
Consumption:
Maximum
Operating
Sleep mode
180 mA @ 5 Vdc
150 mA @ 5 Vdc
500 µA @ 5 Vdc
90 mA @ 12 Vdc
90 mA @ 12 Vdc
20 mA @ 12 Vdc
Max. Scan Rate 256 scans/sec
Reading Indicators LED, Good Read Spot, Beeper
Optical Features
Sensor CCD solid state (2048 pixels)
Illuminator LED array
Wavelength 630 ~ 670 nm
Max. LED Output Power 0.31 mW
LED Safety Class Class 1 EN 60825-1
Reading Field see reading diagrams
Max. Resolution 0.10 mm (4 mils)
PCS min. 15% (Datalogic Test Chart)
Environmental Features
Working Temperature
0 °C to + 55 °C
Storage Temperature
-20 °C to + 70 °C
Humidity 90% non condensing
Drop Resistance
(on concrete)
IEC 68-2-32 Test ED
1.8 m
ESD Protection 16 KV
Protection Class IP30
Mechanical Features
Weight (without cable) about 165 g. (5.8 oz.)
Cable Length 2 m (6 ft. 6 in.)
1 DEFAULT
UK
Read the RESTORE DEFAULT code.
I
Leggere il codice che ripristina i default.
F
Lire le code de configuration par défaut.
D
Lesen Sie den Restore Default Code, um die
Werkseinstellung wieder herzustellen.
E
Leer el código de restaurar los parámetros de
fábrica.
RESTORE DEFAULT
iPk
iPk
iPk
RS232 DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 5 sec., ack/nack disabled, fifo
enabled, serial trigger lock disabled;
DATA FORMAT
: code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator = CR-LF,
character replacement disabled
IBM DEFAULT SETTINGS
DATA FORMAT
: IBM Standard, code identifier disabled, no
header, no terminator
POWER SAVE
scan rate max, standby disabled, sleep disabled
READING PARAMETERS
hardware trigger, trigger active level, no trigger timeout,
Flash On = 1 sec, Flash Off = .6 sec, one read per cycle,
safety time .5 sec, beeper intensity high, tone 2, beeper type
monotone, beeper length short, good read spot duration
medium, stand recognition beep enabled; automatic
operation aiming light enabled
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit
control enabled, Puzzle Solver™ disabled, decoding safety
= one read
CODE SELECTION
enabled codes
• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
• Interleaved 2/5
check digit control and transmission, variable length
code; 4-99 characters
• Standard Code 39
no check digit control, variable length code; 1-99
characters
• Code 128
variable length code; 1-99 characters
disabled codes
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical
codes, Standard and EAN, MSI, Plessey, Telepen, Delta
IBM, Code 11, Code 16K, Code 49, RSS Codes
*ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
* The advanced formatting parameters may not be
compatible with the IBM 46xx cash register parameters.
UK
YOUR READER IS NOW READY TO READ
BARCODES.
To change the defaults see the HHD II Software
Configuration Manual, part number 90ACC1877.
I
IL LETTORE È PRONTO A LEGGERE I CODICI.
Per cambiare i parametri di default, fare riferimento
al manuale “HHD II Software Configuration Manual",
n. d'ordine 90ACC1877.
F
VOTRE LECTEUR EST DÉSORMAIS PRÊT A
L’EMPLOI POUR LA LECTURE DE CODES.
Pour changer les paramètres voir le manuel "HHD II
Software Configuration Manual" numéro d'ordre
90ACC1877.
D
DAS LESEGERÄT IST JETZT BEREIT CODES ZU
LESEN.
Um die Werkseinstellungsparameter zu ändern,
schlagen Sie im Handbuch "HHD II Software
Configuration Manual" nach, Bestellnummer
90ACC1877.
E
EL LECTOR ESTÁ LISTO PARA LA LECTURA DE
LOS CÓDIGOS DE BARRAS.
Para cambiar los parámetros de fábrica ver el
manual “HHD II Software Configuration Manual”, n.
de orden 90ACC1877.
OPERATING TEST
UK
Read the TEST codes below.
I
Leggere i codici di test.
F
Lire les codes tests.
D
Lesen Sie die Test-Coden.
E
Leer los siguientes códigos TEST.
EAN-8
1234 5670
EAN-13
1 234567 000992
Code 39 (Normal)
17162
Code 128
test
Interleaved 2 of 5
0123456784
2 READER CONFIGURATION
UK
Read the interface selection code for your applica-
tion.
I
Leggere il codice per la selezione dell’interfaccia
relativo al modo di comunicazione desiderato.
F
Lire le code “Interface” correspondant à votre
modèle.
D
Lesen Sie den Schnittstellen-Code, der Ihrem
gewünschten Kommunikationsmodus entspricht.
E
Leer uno de los siguientes códigos para la selección
del interfaz relativo a su aplicación.
RS232
i$1k
i$1k
i$1k
IBM Terminals 46xx
PORT 9B
4501 Protocol
i$1Qk
i$1Qk
i$1Qk
(typical)
1520 Protocol
i$1Xk
i$1Xk
i$1Xk
PORT 5B
1520 Protocol
i$1Xk
i$1Xk
i$1Xk
(typical)
4501 Protocol
i$1Qk
i$1Qk
i$1Qk
IBM DATA FORMATTING
UK
To select the data formatting for these IBM
Terminals, read one of the code selections below.
(default = IBM Standard).
I
Per i terminali IBM, leggere il codice
corrispondente alla formattazione dei dati
desiderata (default = IBM Standard).
F
Pour sélectionner le format des données pour des
terminaux IBM, lire l’un des codes suivants (par
défaut = IBM Standard).
D
Um die Datenformat für IBM Terminals
einzustellen, lesen Sie einen der folgenden
Strichcodes. (Werkseinstellung = IBM Standard).
E
Para configurar el formato de datos para los
terminales IBM, leer uno de los siguientes códigos.
(default = IBM Standard).
Conversion to Code 39
i(%Hk
i(%Hk
i(%Hk
IBM Standard
i(%Mk
i(%Mk
i(%Mk
Mixed IBM Standard + Code 39
i(%Rk
i(%Rk
i(%Rk
IBM DATA FORMATTING (Transmission Format)
The IBM 46xx Series cash register recognizes the following
codes:
EAN 8 / EAN13 / UPC A / UPC E with and without Add On
Interleaved 2/5
Code 39
Codabar
Code 128
Code 93
Normal 2/5
The transmission format of codes belonging to this set is
specified by the protocol. As the reader allows a wider set of
codes to be selected, the following formats are defined to offer
the user all the reading possibilities of the Datalogic product.
Conversion to Code 39 Format
Data from any code selected may be transmitted. Each code is
transmitted to the Host as Code 39. Any character not included
in the standard Code 39 set will be replaced with a “Space” (20
Hex).
IBM Standard Format (default)
Only codes belonging to the above mentioned set may be
transmitted. Each code transmitted to the Host is recognized by
the identifier requested by the protocol. If the selected code
does not belong to this set, it wiII not be transmitted.
MIXED IBM Standard + Code 39 Format
Data from any code selected may be transmitted. For codes
belonging to the above mentioned set, the “IBM Standard
Format” is applied. The “Code 39’ Format applies to codes not
belonging to this set.
IBM DATA FORMATTING
UK
To select the data formatting for these IBM
Terminals, read one of the code selections below.
(default = IBM Standard).
I
Per i terminali IBM, leggere il codice
corrispondente alla formattazione dei dati
desiderata (default = IBM Standard).
F
Pour sélectionner le format des données pour des
terminaux IBM, lire l’un des codes suivants (par
défaut = IBM Standard).
D
Um die Datenformat für IBM Terminals
einzustellen, lesen Sie einen der folgenden
Strichcodes. (Werkseinstellung = IBM Standard).
E
Para configurar el formato de datos para los
terminales IBM, leer uno de los siguientes códigos.
(default = IBM Standard).
Conversion to Code 39
i(%Hk
i(%Hk
i(%Hk
IBM Standard
i(%Mk
i(%Mk
i(%Mk
Mixed IBM Standard + Code 39
i(%Rk
i(%Rk
i(%Rk
IBM DATA FORMATTING (Transmission Format)
The IBM 46xx Series cash register recognizes the following
codes:
EAN 8 / EAN13 / UPC A / UPC E with and without Add On
Interleaved 2/5
Code 39
Codabar
Code 128
Code 93
Normal 2/5
The transmission format of codes belonging to this set is
specified by the protocol. As the reader allows a wider set of
codes to be selected, the following formats are defined to offer
the user all the reading possibilities of the Datalogic product.
Conversion to Code 39 Format
Data from any code selected may be transmitted. Each code is
transmitted to the Host as Code 39. Any character not included
in the standard Code 39 set will be replaced with a “Space” (20
Hex).
IBM Standard Format (default)
Only codes belonging to the above mentioned set may be
transmitted. Each code transmitted to the Host is recognized by
the identifier requested by the protocol. If the selected code
does not belong to this set, it wiII not be transmitted.
MIXED IBM Standard + Code 39 Format
Data from any code selected may be transmitted. For codes
belonging to the above mentioned set, the “IBM Standard
Format” is applied. The “Code 39’ Format applies to codes not
belonging to this set.
OPERATING TEST
UK
Read the TEST codes below.
I
Leggere i codici di test.
F
Lire les codes tests.
D
Lesen Sie die Test-Coden.
E
Leer los siguientes códigos TEST.
EAN-8
1234 5670
EAN-13
1 234567 000992
Code 39 (Normal)
17162
Code 128
test
Interleaved 2 of 5
0123456784
2 READER CONFIGURATION
UK
Read the interface selection code for your applica-
tion.
I
Leggere il codice per la selezione dell’interfaccia
relativo al modo di comunicazione desiderato.
F
Lire le code “Interface” correspondant à votre
modèle.
D
Lesen Sie den Schnittstellen-Code, der Ihrem
gewünschten Kommunikationsmodus entspricht.
E
Leer uno de los siguientes códigos para la selección
del interfaz relativo a su aplicación.
RS232
i$1k
i$1k
i$1k
IBM Terminals 46xx
PORT 9B
4501 Protocol
i$1Qk
i$1Qk
i$1Qk
(typical)
1520 Protocol
i$1Xk
i$1Xk
i$1Xk
PORT 5B
1520 Protocol
i$1Xk
i$1Xk
i$1Xk
(typical)
4501 Protocol
i$1Qk
i$1Qk
i$1Qk
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit
control enabled, Puzzle Solver™ disabled, decoding safety
= one read
CODE SELECTION
enabled codes
• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
• Interleaved 2/5
check digit control and transmission, variable length
code; 4-99 characters
• Standard Code 39
no check digit control, variable length code; 1-99
characters
• Code 128
variable length code; 1-99 characters
disabled codes
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical
codes, Standard and EAN, MSI, Plessey, Telepen, Delta
IBM, Code 11, Code 16K, Code 49, RSS Codes
*ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
* The advanced formatting parameters may not be
compatible with the IBM 46xx cash register parameters.
UK
YOUR READER IS NOW READY TO READ
BARCODES.
To change the defaults see the HHD II Software
Configuration Manual, part number 90ACC1877.
I
IL LETTORE È PRONTO A LEGGERE I CODICI.
Per cambiare i parametri di default, fare riferimento
al manuale “HHD II Software Configuration Manual",
n. d'ordine 90ACC1877.
F
VOTRE LECTEUR EST DÉSORMAIS PRÊT A
L’EMPLOI POUR LA LECTURE DE CODES.
Pour changer les paramètres voir le manuel "HHD II
Software Configuration Manual" numéro d'ordre
90ACC1877.
D
DAS LESEGERÄT IST JETZT BEREIT CODES ZU
LESEN.
Um die Werkseinstellungsparameter zu ändern,
schlagen Sie im Handbuch "HHD II Software
Configuration Manual" nach, Bestellnummer
90ACC1877.
E
EL LECTOR ESTÁ LISTO PARA LA LECTURA DE
LOS CÓDIGOS DE BARRAS.
Para cambiar los parámetros de fábrica ver el
manual “HHD II Software Configuration Manual”, n.
de orden 90ACC1877.
TECHNICAL FEATURES
Heron
D110
Electrical Features
Power Supply
RS232 interface
IBM 46xx
5 Vdc ± 5%
12 Vdc directly taken from cash
register
RS232 IBM 46xx
Consumption:
Maximum
Operating
Sleep mode
180 mA @ 5 Vdc
150 mA @ 5 Vdc
500 µA @ 5 Vdc
90 mA @ 12 Vdc
90 mA @ 12 Vdc
20 mA @ 12 Vdc
Max. Scan Rate 256 scans/sec
Reading Indicators LED, Good Read Spot, Beeper
Optical Features
Sensor CCD solid state (2048 pixels)
Illuminator LED array
Wavelength 630 ~ 670 nm
Max. LED Output Power 0.31 mW
LED Safety Class Class 1 EN 60825-1
Reading Field see reading diagrams
Max. Resolution 0.10 mm (4 mils)
PCS min. 15% (Datalogic Test Chart)
Environmental Features
Working Temperature
0 °C to + 55 °C
Storage Temperature
-20 °C to + 70 °C
Humidity 90% non condensing
Drop Resistance
(on concrete)
IEC 68-2-32 Test ED
1.8 m
ESD Protection 16 KV
Protection Class IP30
Mechanical Features
Weight (without cable) about 165 g. (5.8 oz.)
Cable Length 2 m (6 ft. 6 in.)
1 DEFAULT
UK
Read the RESTORE DEFAULT code.
I
Leggere il codice che ripristina i default.
F
Lire le code de configuration par défaut.
D
Lesen Sie den Restore Default Code, um die
Werkseinstellung wieder herzustellen.
E
Leer el código de restaurar los parámetros de
fábrica.
RESTORE DEFAULT
iPk
iPk
iPk
RS232 DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking,
delay disabled, rx timeout 5 sec., ack/nack disabled, fifo
enabled, serial trigger lock disabled;
DATA FORMAT
: code identifier disabled, no field adjustment,
code length not transmitted, no header, terminator = CR-LF,
character replacement disabled
IBM DEFAULT SETTINGS
DATA FORMAT
: IBM Standard, code identifier disabled, no
header, no terminator
POWER SAVE
scan rate max, standby disabled, sleep disabled
READING PARAMETERS
hardware trigger, trigger active level, no trigger timeout,
Flash On = 1 sec, Flash Off = .6 sec, one read per cycle,
safety time .5 sec, beeper intensity high, tone 2, beeper type
monotone, beeper length short, good read spot duration
medium, stand recognition beep enabled; automatic
operation aiming light enabled
INSERTION INTO STAND
UK
Pair the reader to the stand paying attention to
insert the handle into the stand clip (see figure
above). Correct insertion will be signaled by a
beep; the reader will then be ready to read
barcodes.
I
Posizionare la pistola nello stand assicurandosi
che il manico sia inserito nel fermo dello stand
stesso (vedi figura sopra). Un beep sonoro
segnalerà il corretto inserimento ed il lettore sarà
pronto per leggere i codici a barre.
F
Placer le pistolet dans le support en faisant
attention d’introduire la poignée dans le crochet du
support (voir figure ci-dessus). Un beep sonore
indiquera un positionnement correct. Le pistolet
est ainsi prêt à lire les codes.
D
Positionieren Sie die Pistole im Halter und stecken
Sie den Griff in die Öffnung des Halters (siehe Bild
oben). Das korrekte Positionieren wird durch einen
Piepton angezeigt. Dann ist die Pistole bereit
Codes zu lesen.
E
Poner el lector en su soporte insertando la
empuñadura en el clip del soporte (ver figura
arriba). El soporte emitirá un pitido al insertar el
lector de forma correcta. El lector estará entonces
listo para leer códigos de barras.
READING DIAGRAM
0
5
10
15
20
25
30
35
-15
-10
-5
0
5
10
15
D110 - Reading Zones (10° skew angle)
(cm)
CODE 39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE 39
0.50 mm
(20 mils)
0.13 mm
(5 mils)
FCC COMPLIANCE
This device complies with PART 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference which
may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
LED CLASS
R
CUS
SEE PACKAGE FOR
PATENT LISTING
UK
Class 1 LED product
I
Apparecchio LED classe 1
F
Appareil à LED de classe 1
D
LED Klasse 1
E
LED Clase 1
This product conforms to EN60825-1:2001.
PATENTS
This product is licensed by one or more of the following U.S.
patents:
4,894,523; 5,021,642; and 6,158,661
This product is covered by one or more of the following patents:
U.S. patents 5,992,740; 6,305,606 B1; 6,631,846 B2;
6,517,003 B2; and 6,712,271 B2
European patents 851,378 B1; 895,175 B1; 962,880 B1;
997,760 B1; and 1,128,315 B1
Additional patents pending.
F
Pour le montage du support il est possible également d’utiliser
des vis filetées, des bandes adhésives ou des petits patins en
caoutchouc:
A) utiliser des vis filetées pour le montage sur la surface
d’appui;
B) nettoyer soigneusement la surface inférieure du support et
la surface d’appui.
Retirer le plastique protecteur de l’une
des faces des bandes et la coller sur la surface inférieure
du support. Retirer le plastique protecteur sur l’autre face
adhésive et coller le support sur la surface d’appui ;
C) nettoyer soigneusement la surface inférieure du support.
Retirer la pellicule protectrice des patins et coller les patins
dans les logements correspondants situés sur la surface
inférieure du support. Il est possible aussi de fixer une
plaque métallique en option.
D
Der Halter kann mittels der selbstschneidenden Schrauben, der
Klebstreifen oder mittels der Gummifüßchen befestigt werden:
A) für eine permanente Installation verwenden Sie die zwei
selbstschneidenden Schrauben.
B) die untere Seite des Halters und die Ablagefläche sorgfältig
reinigen. Die Schutzschicht von einer Seite jedes
Klebstreifens entfernen und beide Klebstreifen auf den
Halters kleben. Die Schutzschicht von der anderen Seite
der Klebstreifen entfernen und den Halter auf der
Ablagefläche befestigen.
C) die untere Seite des Halters und die Ablagefläche sorgfältig
reinigen um die Füßchen auf die Sitzen des Halters zu
kleben. Man kann auch eine optionale Metallunterlage
befestigen.
E
El soporte puede ser montado a través de tornillos auto-
bloqueantes (A), tiras adhesivas de doble cara (B) o pies de
goma (C):
A) Montar el soporte directamente sobre la superficie
utilizando los tornillos auto-bloqueantes;
B) Limpiar con cuidado la superficie inferior del soporte y la
superficie de la mesa. Quitar el plástico de protección de
una de las caras de las tiras adhesivas y pegarla a la
superficie inferior del soporte. Luego quitar el plástico de la
otra cara de la tira adhesiva y posicionar el soporte en la
posición deseada sobre la mesa;
C) Limpiar con cuidado la superficie inferior del soporte, quitar
el plástico de protección de los pies de goma e insertarlos
en las posiciones correspondientes en la superficie inferior
del soporte. Es posible también fijar una placa de metal
opcional.
STAND INSTALLATION
UK
The stand can be mounted by using self-tapping screws,
double sided adhesive strips or rubber feet:
A) mount the stand directly to the surface using the
self-tapping screws;
B) carefully clean the bottom surface of the stand and the
table surface. Remove the protective plastic from one side
of the adhesive strips and stick them on the stand bottom.
Then, remove the plastic from the other side of the strips
and affix the stand to the table;
C) carefully clean the bottom surface of the stand, remove the
protective film from the rubber feet and stick them in the
corresponding housing on the bottom surface. It is also
possible to fix an optional metal plate.
I
Lo stand può essere montato utilizzando le viti autofilettanti, le
strisce adesive oppure i piedini di gomma:
A) montare lo stand direttamente sulla superficie utilizzando le
viti autofilettanti;
B) pulire accuratamente la superficie inferiore della base dello
stand e la superficie d’appoggio. Togliere la plastica
protettiva da un lato di ogni striscia e attaccare entrambe le
strisce alla base dello stand. Rimuovere la plastica
protettiva dall’altro lato delle strisce adesive e attaccare lo
stand alla superficie d’appoggio;
C) pulire accuratamente la superficie inferiore della base dello
stand, quindi togliere la pellicola protettiva dai piedini e
attaccarli all’interno delle apposite sedi nella base di
plastica. Inoltre, è possibile fissare un base metallica
opzionale.
WARRANTY
UK
Datalogic warranties this product against defects in
workmanship and materials, for a period of 5 years
from the date of shipment, provided that the product
is operated under normal and proper conditions.
Datalogic has the faculty to repair or replace the
product, these provisions do not prolong the original
warranty term.
The warranty does not apply to any product that has
been subject to misuse, accidental damage,
unauthorized repair or tampering.
I
Datalogic garantisce questo prodotto contro difetti di
fabbricazione e di materiali per 5 anni dalla data di
consegna, a condizione che il prodotto sia utilizzato
come previsto.
Datalogic si riserva la facoltà di riparare o sostituire il
prodotto. Quanto sopra non prolunga la garanzia
originale.
La garanzia non si applica a prodotti utilizzati in modo
non corretto, danneggiati accidentalmente, sottoposti
a riparazioni non autorizzate o manomessi.
F
Datalogic garantit ce produit de tout défaut de
fabrication ou des matériaux pendant 5 ans à compter
de la date de livraison, à condition que le produit soit
utilisé correctement.
Datalogic a la faculté de réparer ou de remplacer ce
produit. Ces mesures ne prolongeront pas l’échéance
de la garantie.
La garantie ne s’applique pas aux produits qui ont été
utilisés de façon incorrecte, accidentellement
endommagés, soumis à des réparations non
autorisées ou bien altérés.
D
Datalogic gibt für dieses Produkt eine Garantie von 5
Jahren auf Herstellungs- und Materialfehler ab
Versandsdatum, falls das Produkt unter normalen und
angemessenen Bedingungen verwendet wurde.
Datalogic behält sich vor, das Produkt entweder zu
reparieren oder zu ersetzen, was aber den originalen
Garantietermin nicht verlängert.
Die Garantie erlischt bei unsachgemäßer Verwendung
und unberechtigter Veränderungen am Produkt.
E
Datalogic garantiza este producto contra todos los
defectos de fabricación y materiales por un periodo
de 5 años desde la fecha de envío, a condición de
que el producto sea utilizado en condiciones
normales y correctas.
Datalogic tiene el derecho de reparar o reemplazar el
producto sin que esto suponga una prolongación de
la garantía original.
La garantía no será valida si el producto ha sufrido
abusos, daños accidentales, reparaciones no
autorizadas o ha sido falsificado.
A
B
C
SERVICES AND SUPPORT
UK
Datalogic provides several services as well as
technical support through its website. Log on to
www.datalogic.com/services and click on the links
indicated for further information including:
I
Datalogic fornisce servizi e supporto tecnico tramite
il suo sito web. Connettersi al sito
www.datalogic.com/services e cliccare sui link
indicati per avere ulteriori informazioni, come
elencato di seguito:
F
Datalogic fournit différents services et une aide
technique en ligne. Connectez-vous sur
www.datalogic.com/services et cliquez sur le lien
indiqué pour obtenir des informations
complémentaires sur:
D
Datalogic bietet unterschiedliche Service-
Leistungen, wie auch technische Unterstützung über
Internetseiten. Gehen Sie auf die Seite
www.datalogic.com/services und klicken Sie auf
die Links
die Sie über folgende Punkte informieren:
E
Datalogic proporciona servicios y soporte técnico a
través su página web. Hay que conectarse a
www.datalogic.com/services y hacer clic en los
enlaces
indicados a continuación para recibir más
información:
• Datalogic Services
- Warranty Extensions and
Maintenance Agreements
• Downloads
- Software Downloads, Manuals and
Catalogues
• Contact Us
- Listing of Datalogic Subsidiaries and
Quality Partners
• Authorised Repair Centres
• Products
>Hand-Held Readers >Software Tools - DL
Sm@rtSet™
DL Sm@rtSet™ is a Windows-based utility program
which allows device configuration using a PC. It provides
RS232 interface configuration as well as configuration
barcode printing.
CONNECTIONS
RS232
With the RS232 cable, this accessory device is intended to be
supplied by a UL Listed or CSA Certified Direct Plug-in Power
Unit marked "Class 2", rated 5 V, minimum 180 mA.
IBM port 9B / IBM port 5B
With the IBM terminal 5B and 9B port cables, this accessory
device is intended to be connected to a UL Listed or CSA
Certified Computer which supplies power directly to the reader.
DISCONNECTING THE CABLE
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Datalogic Heron D110 Guide de référence
- Catégorie
- Lecteurs de codes à barres
- Taper
- Guide de référence
dans d''autres langues
- italiano: Datalogic Heron D110 Guida di riferimento
- English: Datalogic Heron D110 Reference guide
- español: Datalogic Heron D110 Guia de referencia
- Deutsch: Datalogic Heron D110 Referenzhandbuch
Documents connexes
-
Datalogic Heron D110 RS-232 and IBM 46XX Manuel utilisateur
-
Datalogic FireScan D111 Series Guide de référence
-
Datalogic Heron D150 Manuel utilisateur
-
Datalogic Heron D140 LASEROUT Manuel utilisateur
-
-
-
-
-
-