Elac Discovery Series DS-A101-G Wireless Integrated Amplifier Le manuel du propriétaire

Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire
DS-A101-G
80 Watt-per-channel
Integrated amp with STREAMING
INTEGRATED AMPLIFIER
OPERATING INSTRUCTIONS
2
• Explanation of Graphical Symbols
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOQUE ÉLECTRIQUE
N'OUVREZ PAS
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
you to the presence of important operating and maintenance (servic-
ing) instructions in the literature accompanying the product.
APPLICABLE FOR USA, CANADA OR
WHERE APPROVED FOR USAGE
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE PLUG TO
WIDE SLOT, INSERT FULLY.
ATTENTION: POUR EVITER LES CHOCS
ELECTRIQUES, INTRODUIRE LA LAME
LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU AU FOND.
CAUTION: To reduce the risk of electric shock, do not remove cover (or
back).
No user-serviceable parts inside. Refer servicing to qualified service
personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provid-
ed plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use cau-
tion when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-sup-
ply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or mois-
ture, does not operate normally, or has been dropped.
15. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the appa-
ratus.
16. CAUTION: Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you are qualified to do so.
17. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
PORTABLE CART WARNING
Important Safety Instructions
3
Table of Contents
Important Safety Instructions ................................................................................................................................. 2
Table of Contents....................................................................................................................................................3
Introduction ............................................................................................................................................................. 4
DS-A101-G Features ...............................................................................................................................................5
Front Panel Features .................................................................................................................................................
Power......................................................................................................................................................................6
IR Sensor .................................................................................................................................................................6
Front Panel Display ................................................................................................................................................6
Source ....................................................................................................................................................................6
Phones .................................................................................................................................................................... 6
Volume Control .....................................................................................................................................................6
Rear Panel Features ...............................................................................................................................................7
AC Mains ................................................................................................................................................................ 7
Line In .....................................................................................................................................................................7
Line 2 In ..................................................................................................................................................................7
Sub Out ..................................................................................................................................................................7
Coax In ...................................................................................................................................................................7
Speaker Out ...........................................................................................................................................................7
Pair ..........................................................................................................................................................................8
Ethernet ..................................................................................................................................................................8
Optical In ...............................................................................................................................................................8
IR Remote Features.................................................................................................................................................9
Power......................................................................................................................................................................9
Volume/Transport .................................................................................................................................................9
Input Select ............................................................................................................................................................ 9
Bluetooth ................................................................................................................................................................ 9
Streaming ............................................................................................................................................................... 9
Installation .............................................................................................................................................................10
AmplierLocation ...............................................................................................................................................10
Typical System .....................................................................................................................................................10
Connections ..........................................................................................................................................................11
Speaker Connections ......................................................................................................................................... 11
Other Connections .............................................................................................................................................11
IR Remote/Front Panel Control ............................................................................................................................ 12
ON/OFF ................................................................................................................................................................12
Volume/Mute ......................................................................................................................................................12
Source Select .......................................................................................................................................................12
Bluetooth ...............................................................................................................................................................13
BluetoothPairingELACUSBAmplier ...............................................................................................................13
Bluetooth Pairing DS-A101-G Control ...............................................................................................................13
DS-A101-G App ....................................................................................................................................................14
Master Volume ....................................................................................................................................................14
Offset Volume......................................................................................................................................................14
Setup ....................................................................................................................................................................15
Input Names ........................................................................................................................................................15
Bass/Treble ...........................................................................................................................................................16
Screen Brightness ................................................................................................................................................16
Speaker Balance.................................................................................................................................................17
Remote Learning ................................................................................................................................................18
About ....................................................................................................................................................................19
Warranty ................................................................................................................................................................20
4
Introduction
CongratulationsandthankyouforpurchasingtheELACDS-A101-GIntegratedAmplier!
Sincethetimewestartedin1926,ELAChasalwaysstriventoachievetheverybest!
While a handful of separates and integrated units offered great sound, none delivered the
performance,exibilityandvalueessentialforaproducttocarrytheELACname.Sowhere
none existed before, our engineers started with a clean-sheet and simple design brief: build
themostpowerful,versatile,easy-to-useintegratedampliersimaginable;doitwithout
compromisingsound,reliabilityandagreatuserexperience;andpriceitsofairlythatit
becomes a hands-down choice even when compared against units at many times the
price.
The BASH
®
Amplication System
AtitsheartisabrandnewBASHTrackingAmplierdeliveringupto160Watts.Thisnew
amplierusesamodulatedswitchedmodepowersupplyalliedtoaconventionalclassAB
amplier.Switchingatmorethan400,000timespersecond,thesupplytrackstheincoming
audiosignaltoensurethattheClassABampliergetsonlythevoltagenecessary(withalittle
headroom) to cope with today’s dynamic movie and music content, thus maximizing the
efciencyandpotentialoftheamplier.
App-rich Control Flexibility
ELAC’s free iOS and Android app allows users to fully control and set up their system. The app
includes innovative features not found on any other products in this class—anywhere.
Input Rename
Easily rename each input to match your source. The revised name will appear in the app
andontheintegratedamplier’sfrontpaneldisplay.
Loudness Reinvented
Insteadoftheusualxedboostofbassandtreble,theloudnesscompensationfeature
allows users to tailor the loudness level to their liking.
Auto Blend and Auto EQ
ThroughtheuseofthefreeiOSandAndroidapptheuserrstselectsahigh-passlter,then
usingthesmartphonesmicrophone,measuresthenear-eldresponseofboththemain
speakersandsubwoofer.Ourproprietaryalgorithmthenadjuststhelowpassltertoobtain
optimal blending between the subwoofer and main speakers. Auto EQ minimizes the effects
of the rooms acoustics allowing you to hear the sound the designer intended.
Please read and follow the instructions in this guide to assist in proper installation, connection
anduseofyourELACDS-A101-GIntegratedAmplier.
5
DS-A101-G Features
WHAT’S INCLUDED
1-DS-A101-GIntegratedAmplier
1 - IR Remote Control
2 - AAA Batteries
1 - DS-A101-G Operating Instructions
DS-A101-G FEATURES
Basic Description
FiveSource,80Watt-per-channelIntegratedAmplier
Streaming: ROON, SPOTIFY, BLUETOOTH, AIRPLAY, DLNA, DISCOVERY
Amplier
2x80Watts;BASHTrackingAmplier
80W Continuous x 2 Channels @4Ωwith1%THD
Pleasevisitourwebsiteforfullamplierdetailsandperformancespecications
Audio Inputs
2 x Stereo Analog Line Level Audio Inputs
1 x Digital Optical Audio Inputs (up to 192kHz 24-bit)*
1 x Digital Coaxial Audio Input (up to 192kHz 24-bit)
*Due to differences in optical transmitters and optical cable quality/length, 192kHz is not guaranteed
Speaker Connections
2 x 5-way Binding Posts
Subwoofer Output
1 x Analog Line Level with AutoEQ
Audio Output
1 x Analog variable preamp
Control
Android or iOS Setup/Control App
IR Remote Control
Bluetooth
©
4.0 Low Energy
Audio Decoders
Dolby Digital 2.1 Decoding
DSP
AutoBlend(subwoofertomainspeakerconguration)
AutoEQ (automatic room correction)
Front Panel Display
OEL (Organic Electro-Luminescence)
6
Front Panel Features
Figure 1 DS-A101-G Front Panel Features
1. POWER - Lightly press to turn unit ON. The ELAC logo will appear in the front panel
display, followed by the current volume setting and currently selected input. Lightly
press again to turn unit OFF. Front panel display will turn OFF. Power can also be turned
ON/OFF with the hand-held IR Remote.
2. IR SENSOR - IR eye ‘sees’ IR commands from the DS-A101-G handheld remote. The IR
Sensor must be line-of-sight to the remote to receive commands. The IR Sensor can also
be used for learning IR commands from a third-party integrated remote allowing system
control from a single remote control.
3. FRONT PANEL DISPLAY - Front panel OEL (Organic Electro-Luminescence) display
indicates ON/OFF status, source selected, volume/mute setting and Dolby Audio™ logo
when Dolby Digital signals are being received.
4. SOURCE - Lightly tap the Source button to change input selections one at a time. Press
and hold to scroll inputs to the desired selection.
5. VOLUME CONTROL - Turn clockwise (to the right) to increase volume through speakers
or headphones. Turn counter-clockwise (to the left) to decrease volume. This is a digital
control and does not have a physical stop. Watch the front panel display for level and
becarefultonotdamagetheamp,speakersoryourears!TheVolumeControlwillalso
adjust the output level of the Sub Out, if used.
1
2
3
4
5
7
Rear Panel Features
Figure 2 DS-A101-G Rear Panel Features
6. AC MAINS - Afterallotherconnectionshavebeenmadeandconrmed,usingthe
included power cord, connect the AC Mains on the DS-A101-G to an unswitched AC
outlet.
7. LINE IN - Using a quality stereo RCA to RCA cable, connect the L&R outputs on a stereo
audio source to the Line IN L&R inputs on the DS-A101-G. This input can be selected by
pressing Ana 1 on the remote or by tapping the front panel Source button.
8. LINE 2 IN - Using a quality stereo RCA to RCA cable, connect the L&R outputs on a
stereo audio source to the Line 2 IN L&R inputs on the DS-A101-G. This input can be
selected by pressing Ana 2 on the remote or by tapping the front panel Source button.
9. COAX IN - Using a quality digital coaxial audio cable, connect the Coaxial OUT on a
source component to the Coax IN on the DC-A101-G. The Dolby logo will appear in the
front panel display when Dolby Digital signals are present. This input can be selected by
pressing Coax on the remote or by tapping the front panel Source button.
10. ANALOG PRE OUT - Using a quality RCA to RCAcable, connect your PREAMP to the
ANALOG PRE OUT on the rear of DS-A101-G.
11. SPEAKER OUT - Using 16AWG (min) speaker wire, connect the Right and Left Speaker
terminals on the DS-A101-G to the appropriate speaker terminals on left and right
speakers. Before connecting the speaker wires, twist the ends of the speaker wire
so there are no strays that can cause shorts. See section: Connections/Speaker
Connections for additional information.
6
7
8 9
10
11
15 14
13 12
8
12. SUB OUT - Using a quality RCA to RCA cable, connect the SUB OUT on the DS-A101-G to
the SUB IN on a powered subwoofer or sub amp. Once the initial sub settings have been
made, the Volume Control will adjust both Speaker and Sub Out levels as a master
control.
13. ETHERNET - Using an Ethertnet cable, connect the ETHERNET port on the DS-A101-G to
local network (LAN).
This input can be selected by pressing on the remote or by tapping the front
panel Source button.
Alternatively, LAN connection can also be setup via WIFI using the app, instead of
ETHERNET cable.
14. PAIR - Push this small button to pair DS-A101-G with Bluetooth devices for audio
streaming.
15. OPTICAL IN - Using a quality digital optical audio cable, connect the Optical OUT on a
source component to the Optical IN on the DS-A101-G. The Dolby logo will appear in
the front panel display when Dolby Digital signals are present. This input can be selected
by pressing Opt on the remote or by tapping the front panel Source button.
Rear Panel Features (cont)
9
IR Remote Features
Figure 3
DS-A101-G IR Remote Features
1. POWER - Press to turn unit ON. The ELAC logo will
appear in the front panel display, followed by the
current volume setting and currently selected input.
Press again to turn unit OFF. Front panel display will
turn OFF. Power can also be turned ON/OFF with the
front panel Power button
2. VOLUME/TRANSPORT -
Volume - The Volume controls will adjust the
volume to the speakers, subwoofer, (if used) or
headphones, (if connected).
Press Vol+ to increase volume.
Press Vol - to decrease volume.
Transport - The Transport buttons will control
play/pause, previous track and next track on a
compatible Android or iOS device that is paired to
the DS-A101-G.
Press once to Play a selected track.
Press again to Pause a selected track.
Press to select the previous track.
Press to select the next track.
3. INPUT SELECT - Press these buttons to select audio
source devices connected to the DS-A101-G rear
panel inputs.
Ana 1 - Press to select the device connected to
Line IN.
Ana 2 - Press to select the device connected to
Line 2 IN.
Opt - Press to select the device connected to
Optical IN.
Coax - Press to select the device connected to
Coax IN.
(BLUETOOTH) - Press this button for various
Bluetooth functions. See section: Bluetooth for
additional information.
(STREAMING) - Press this button for various
streaming options.
4. Mute- Press this button to mute the audio.
1
2
3
4
10
Installation
Amplier Location
Beforemakinganyconnections,besuretolocatetheDS-A101-Gonastable,atsurface
suchasashelfortabletop.Provideenoughspacearoundtheamplierforthefreeowof
air, and do no block any of the vents on the bottom, sides or top, particularly if the amp is
going to be located in a cabinet or closet. Leave enough space around the amp for the
wires that are connected to the amp and other devices and do not allow the wires to block
theventsorthefreeowofairaroundtheamp.Donotexposetheamptodirectsunlight.
Figure 4 Typical DS-A101-G System
SERVICE
RESET
LFE IN
POWER
100-120V/220-240V
~50/60Hz 2A
T2A L 250V
S10EQ HIGH PERFORMANCE SUBWOOFER
Designed in Cypress, CA
ELAC Americas LLC.
11145 Knott Ave. Suite E&F
Cypress, CA. 90630
Serial Number
MADE IN CHINA
Model: DS10EQ1-BK
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY
WITH SAME TYPE FUSE AND RATING.
ATTENTION: UTILISER UNE FUSIBLE DE
RECHANGE DE MEME TYPE ET CALIBRE.
CD PLAYER
OPTICAL COAXIAL
L R
LINE LEVEL OUT
MUSIC SERVER
OPTICAL COAXIAL
L R
LINE LEVEL OUT
BLU-RAY PLAYER
OPTICAL COAXIAL
L R
LINE LEVEL OUT
HDMI
HDMI
ELAC S10EQ SUBWOOFER ELAC B5 BOOKSHELF SPEAKERS
ELAC DS-A101-G
INTEGRATED AMPLIFIER
CD Player
Music Server
Blu-ray Disc Player
HD Video Display
CD Player Line Out to Amp Line In
Server Optical Out to Amp Optical In
Blu-ray Optical Out to Amp Optical In
Blu-ray HDMI Out to TV HDMI In
Android/iOS
Phone/Tablet
with Bluetooth
Running EA101EQ-G App
11
Connections
Speaker Connections
1. Use 16AWG (min) 2-conductor stranded speaker wire for speaker connections.
2. Strip approximately 1/2 to 3/4 of an inch off the ends and twist the strands together so
there are no loose ends that can cause shorts.
3. Ontheamplierrearpanel,turntheclearendsoftheSpeakerTerminalscounterclockwise
so there is enough room between the post and the clear end to feed the stripped wire
through the post hole without damaging the strands.
4. Conrmpolarity.(Redwireto+)
5. Turn the clear ends clockwise to tighten the post and secure the wire.
6. Repeat for left and right speakers, + and -.
7. Conrmconnectionandpolarity.
8. Connect the speaker wires to the appropriate + and - terminals on the speakers.
9. Conrmconnection,polarityandposition.
NOTE: IftheSpeakerOutsensesashort,theamplierwillenterprotectmodeand‘Protect’
will appear in the front panel display. In protect mode, the audio amp will be shut down, but
the logic and control will remain on. Source select and volume changes will be shown in the
display, but there will be no output from the amp and ‘Protect’ will again be shown in the
display after changes are made.
Toresettheamp,powercycletheamp(unplugtheamplierfromthewalljackfor5seconds
and then plug it back in). If the amp does not return to normal operation, please contact
ELAC at 714.252.8843 or at [email protected].
Other Connections
For information on connecting audio devices to the DS-A101-G, see section: Rear Panel Fea-
tures.
For information regarding Bluetooth audio streaming, see section: Bluetooth.
Figure 5 DS-A101-G Speaker Connections
DS-A101-G Rear Panel
SPEAKER OUT
RIGHT LEFT
Red Wire
To Positive
Right Speaker
Red Wire
To Positive
Left Speaker
12
IR Remote/Front Panel Control
IR REMOTE/FRONT PANEL CONTROLS
The DS-A101-G can be controlled via the included IR Remote, front panel controls or DS-
A101-G app. The front panel and remote would typically be used for amp control. The
apphasuniquefeaturesthatcanbeusedfornetuningampperformancebasedupon
thespecicsources,speakersandroomconditions.ThissectioncoversfrontpanelandIR
Remote control. See section: DSA101-G App for information on the use of the app for setup
andnetuning.
ON/OFF
On the IR Remote, Press the button to turn the amp ON. Press again to turn the amp OFF.
On the front panel, Press the Power button to turn the amp ON. Press again to turn the amp
OFF. When the amp is turned ON, the front panel display will show the ELAC logo followed by
the volume level, current source. If the source is outputting a Dolby Digital signal, the Dolby
Audio™ Logo will appear. When the amp is turned OFF the display will turn off.
VOLUME/MUTE
On the IR Remote, Press the button to increase volume. Press the button to
decrease volume. Press the button to mute audio output. Press the button again to
un-mute audio output. On the front panel, turn the Volume knob clockwise (right) to increase
volume. Turn the Volume knob counter-clockwise (left) to decrease volume. There is no front
panel mute control.
When adjusting volume, the volume level will appear in the front panel display.
NOTE: If a subwoofer is connected, the volume/mute controls will affect speaker and sub
volume/mute. If headphones are connected, output to the speakers/sub will be cut and the
volume/mute controls will affect headphone volume/mute.
SOURCE SELECT
On the IR Remote, press the Ana 1, Ana 2, Opt, , Coax or USB buttons to select a
specicsource.Onthefrontpanel,taptheSourcebuttontochangesourceselectionone
at a time. Press and Hold to scroll through available sources to the desired selection.
NOTE: For a Bluetooth source, see section: Bluetooth for additional information.
13
Bluetooth
BLUETOOTH
The DS-A101-G has two connections for Bluetooth. One is for Bluetooth Audio Streaming,
(playing music from a phone or tablet via Bluetooth through the DS-A101-G). The other is for
use with the DS-A101-G App.
Minimum Bluetooth Requirements:
Bluetooth Version: v4.0 or better to run the DS-A101-G App
Bluetooth Proles: A2DP for Bluetooth Audio Streaming and AVRCP for IR control of a paired
phone or tablet
BLUETOOTH PAIRING (BLUETOOTH AUDIO STREAMING)
1. ConrmthatBluetoothisONonthephoneortablettobeusedbygoingtoSettingsand
then Bluetooth in the device menu.
2. On the DS-A101-G IR Remote, press the button to switch the amp to the Bluetooth input.
Next, press and hold the button to start the pairing process. ‘BT Pair’ will appear in the
front panel display.
3. Under Available Devices, look for: ELAC USB Amplier. This is the connection for Bluetooth
Audio Streaming. Tap it. It should pair to the DS-A101-G.
4. To test, press the button on the IR Remote to select the Bluetooth input on the amp. Play
some music on the paired phone or tablet. It should play through the amp. If not, repeat
Steps 1-3toconrmtheELACUSBAmplierBluetoothconnection.
Appropriately featured smartphones, tablets and other devices can be paired to the DS-
A101-G Amp via Bluetooth for Bluetooth Audio Streaming. The DS-A101-G IR Remote can
be used to control transport functions, (play/pause, previous/next track) on appropriately
featuredphonesandtabletsforadditionalcontrolexibility.SeeSection:IR Remote Features
for additional information.
BLUETOOTH PAIRING (DS-A101-G App)
The DS-A101-G App is a setup app that can run on either Android or iOS devices. The
Android version can be downloaded from Play Store. The iOS version can be downloaded
from App Store.
1. Withtheappdownloadedandinstalled,conrmthatBluetoothisONonthephoneor
tablet to be used by going to Settings and then Bluetooth in the device menu.
2. Launch the DS-A101-G App. A black ELAC Screen will appear with an instruction to
select a device from the list. Tap DS-A101-G Control and the app will sync to the amp.
Typically, once the app has been synchronized to the amp from a phone or tablet, unless
the app gets uninstalled, the app will automatically sync to the DS-A101-G amp if the
amp is in range and the app has not been turned off. If the app gets tuned off and gets
relaunched on a previously paired phone or tablet, the app will automatically sync when
launched.
3. Toconrmthattheappissynchronizedtotheamp,taptheAnalog1,Analog2,Coax,
etc. labels at the top of the Master Volume screen. If the source shown on the amp front
panel display changes with the source selected from the app, the app is synchronized.
IMPORTANT NOTE: Bluetooth can be simultaneously connected to two devices, but only
one can play at a given time. If one stops playing, the other can then play. If one device
is connected another can be paired without disconnecting the connected device. If two
devices are connected a new device cannot be paired without disconnecting one of the
connected devices.
14
DS-A101-G APP
The DS-A1010-G App is a two-way setup app that connects to the amp via Bluetooth Low
Energy. App setup features include: source select, master volume, offset (individual source)
volume, source naming, bass/treble, sub volume, balance, Auto Blend, IR Remote learning
and screen brightness. The app will open to the Master Volume screen when launched.
DS-A101-G App
MASTER VOLUME
TheMasterVolumeslidersetstheamplier
output volume. It affects the output to the
speakers and sub (if used) and headphones if
connected.
When adjusting master volume, the volume
level will appear in a bubble on the app
screen and on the front panel display. If the
volume is adjusted with the IR remote or front
panel volume control, the app master volume
will adjust automatically in real time.
OFFSET VOLUME
The Offset Volume slider sets the output of
each connected source relative to the other
sources. This allows adjusting the source
levels so when switching from one source to
another, one won’t be very loud and another
very soft. When adjusting Offset level be
sure to use program material that is equal in
intensity, volume and dynamics so the settings
are made to the relative output of the sources
and not the program material itself. Setting
the Offset on one source to soft solo harp
music and another to pounding electronic
dance music will not result in proper settings.
The app provides two digital meters to
Figure 6 DS-A101-G App - Master Volume
indicate the relative input and output level of each source. Green is good. Amber is OK, but
not too much, and Red is bad. The ideal settings have the Output levels set so that no source
isintheredandmaybejustickeringtheambercell.Alsotrytosettheindividualoutputsso
that no source can get so loud that it can damage the amp, speakers or your ears, even if
theampgetsturnedallthewayup!TheOffsetlevelscanonlybeadjustedusingtheapp...so
keeptheappawayfromthekidsandfriends!
1. Before setting the Offsets, turn the Master Volume down a bit just in case a particular
source comes on louder than expected.
2. With all connected sources playing consistent program material, tap through all inputs at
the top of the app screen to get a feel for which input are louder and softer.
3. Adjust the Offset for each source until the output from the speakers, or headphones is
consistent across all sources. The settings will be automatically stored in the amp.
15
DS-A101-G App
SETUP
The settings for Input Names, Bass/Treble,
Sub Level, Screen Brightness and Speaker
Balance can all be accessed by tapping
the Settings Gear in the top right corner of
the app when in the Source select/Volume
screen. (Figure 6)
Tap the gear. The Settings Menu will appear.
INPUT NAMES
Each of the inputs can be renamed to
indicate the actual connected source...i.e.
Optical 1 can be changed to TV or
Blu-ray. USB can be changed to Computer
or Server. The maximum number of
characters is 9.
1. In the settings menu tap Input Names.
2. Tap to the right of a NAME in the list.
Repeatedly tap the backspace key to
delete the default name. OR...Drag/
select a name in the list.
3. The device keyboard will appear. Type
the new name...Cable, Blu-ray, Internet,
Server, etc.
4. Tap next to change other names and
repeat Steps 2-4.
5. Whennishedtaptheslidericonatthe
top right to return to the source/volume
screen or select another setting in the
menu bar. To return to the Setup menu
tap the back button on the phone or
tablet.
Figure 7 DS-A101-G App - Setup Menu
Figure 8 DS-A101-G App - Name Inputs
16
DS-A101-G App
BASS/TREBLE
The Bass/Treble section adjusts the tone
controls for the DS-A101-G master output.
Each control can be adjusted +/-12dB.
1. In the Settings Menu tap Bass/Treble.
2. Withangertip,slidethebluedotonthe
Bass slider to adjust bass to desired level.
A bubble will appear to indicate level
setting.
3. Withangertip,slidethebluedotonthe
Treble slider to adjust treble to desired
level. A bubble will appear to indicate
level setting.
4. Settings will be automatically stored in the
amp.
5. To return to the Setup Menu tap the back
button on the phone or tablet.
6. Whennishedtaptheslidericonatthe
top right to return to the source/volume
screen.
SCREEN BRIGHTNESS
Screen Brightness adjusts the intensity of the
DS-A101-G front panel display.
RANGE: 1-100.
The Screen Auto ON/OFF sets the front panel
display to stay on or turn off after making
changes to power, source, volume, etc.
1. In the settings menu tap Brightness.
2. Withangertip,slidethebluedotonthe
Brightness slider to adjust the front panel
display intensity to desired level. A bubble
will appear to indicate level setting.
3. To change the Screen Auto ON/OFF
Figure 9 DS-A101-G App - Bass/Treble
Figure 10 DS-A101-G App - Screen Brightness
Setting, slide the switch to the left (white) to have the display remain on while the amp is
powered ON. Slide the switch to the right (blue) to have the display turn off after making
changes to power, source, volume, etc while the amp is powered ON.
4. Settings will be automatically stored in the amp.
5. To return to the Setup Menu tap the back button on the phone or tablet.
6. Whennishedtaptheslidericonatthetoprighttoreturntothesource/volumescreen.
17
DS-A101-G App
SPEAKER BALANCE
Speaker Balance adjusts the relative volume
of the left and right speakers. Use this control
to adjust the stereo sound from the speakers
if they are unevenly placed relative to
the listening position. Each control can be
adjusted +/-100 with 0 being center.
1. In the settings menu tap Balance.
2. Withangertip,slidethebluedotonthe
Speaker Balance slider to adjust balance
to the desired position. A bubble will
appear to indicate the setting.
3. Setting will be automatically stored in the
amp.
4. To return to the Setup Menu tap the back
button on the phone or tablet.
5. Whennishedtaptheslidericonatthe
top right to return to the source/volume
screen.
Figure 11 DS-A101-G App - Balance
18
DS-A101-G App
REMOTE LEARNING
The Remote Learning section allows the DS-
A101-G to learn IR commands from other
remote controls. This can simplify user control
by teaching the amp commands from
another remote such as a TV remote so that
remote can be used to control the TV, DS-
A101-G and other devices if capable.
When learning commands, be sure to use
commands that will make sense when
controlling the amp. Use volume up/down
commands for volume. Use source select
commands for source select functions. Use
transport functions for play/pause/previous/
next.
NOTE: The Play/Pause button is also a mute
button except when used in Bluetooth mode
where it is a pause/play command for a
synchronized Bluetooth device. So...a mute
command will mute/unmute the speakers
for all sources except Bluetooth where it will
pause/play the synchronized device.
1. In the source/Master Volume screen, tap
the Setup Gear in the upper right corner.
From the Setup Menu, tap Remote
Learning. The Remote Learning - Select
screen will appear.
2. In the ‘Select’ screen tap a button to be
replaced with a new IR command. Follow
the cues on the amp front panel display.
Scanning’ will appear on the display.
3. Press the button on the remote to be
learned until the amp display indicates:
‘Captured’. The Display will indicate ‘OK’
if the code was learned.
4. When ‘Again’ appears on the front panel
display, press the SAME BUTTON on the
remote to be learned until the amp
again indicates: ‘Captured’.
5. The amp will return to it’s previous
operating mode.
6. Press the button on the learned remote
to test the command to be sure the
command has been learned and is
affecting the proper function.
Figure 12 DS-A101-G App -
Remote Learning - Select
Figure 13 DS-A101-G App -
Remote Learning - Learn
19
DS-A101-G App
7. Repeat Steps 2-6 for all commands to be
learned.
8. For additional Setup Modes, tap an item
from the Menu Bar at the top of the
screen.
9. Whennishedtaptheslidericonatthe
top right to return to the source/volume
screen.
ABOUT
The About screen indicates important
information about the device to which the
app is synchronized (DS-A101-G). This can
be useful for service purposes to determine
whether the device has most current
rmwaretoprovidebestperformanceand
latestfeatures.Toconrmrmwareversion:
1. With the DS-A101-G app synchronized
to the amp, select About from the Setup
Menu Bar.
Periodically visit http://elac.com/rmware
tocheckforrmwareupdatestoassure
your amp has all current feature and
performance updates.
Figure 14 DS-A101-G App - About
20
DS-A101-G App
WIFI SETUP
Usethissetuppagetocongurethe
DS-A101-Gwithyourwinetwork.
The page shown in Figure 15 displays the
current status. It can display one of the
following connection status:
not connected
connectedtowi
connected to ethernet
You can use speaker connection status to
determineifwisetupwassuccessful.
Inordertoseethewiconnection,make
sure the ethernet is not connected, because
the DS-A101-G will favor the ethernet
connectionoverwiconnection.
Tocreateawiconnectiondothefollowing
steps:
1. Choseawinetworkfromthelisttostart
wisetup.Ifthelistisempty,makesure
wiisenabledonthephone.
2. Enterwinetworkpasswordinthe
requiredeldandpressSUBMIT.See
Figure 16.
3. Gobacktowisetuppagetocheckthe
wiconnectionstatus.
Figure 15 DS-A101-G App -
WIFI - Current status display
Figure 16 DS-A101-G App -
WIFI - Password Submit
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Elac Discovery Series DS-A101-G Wireless Integrated Amplifier Le manuel du propriétaire

Catégorie
Équipement musical supplémentaire
Taper
Le manuel du propriétaire