Burkert 8025 Series Guide de démarrage rapide

Quickstart

Type 8025 / 8035

Flowmeter

English

We reserve the right to make technical changes without notice.

Technische Änderungen vorbehalten.

Subject to technical changes.

Quickstart 1312/0_EU-ML 00565666 ORIGINAL_FR

1. ABOUT THE QUICKSTART.........................................................................3

2. INTENDED USE ................................................................................................4

3. BASIC SAFETY INFORMATION ...............................................................4

4. GENERAL INFORMATION ...........................................................................6

5. DESCRIPTION OF THE NAME PLATE ..................................................6

6. TECHNICAL DATA ...........................................................................................7

7. INSTALLATION ...............................................................................................13

8. WIRING ...............................................................................................................20

9. INSTALLATION AND COMMISSIONING ...........................................49

10. MAINTENANCE AND TROUBLESHOOTING ................................ 55

11. PACKAGING, TRANSPORT ...................................................................55

13. DISPOSAL OF THE PRODUCT ........................................................... 56

3

About the Quickstart

Type 8025/8035 /

ATTENTION

Warns against a possible risk.

• Failure to observe this warning can result in substantial or minor

injuries.

NOTE

Warns against material damage.

• Failure to observe this warning may result in damage to the

device or system.

indicates additional information, advice or important

recommendations.

refers to information contained in this manual or in other

documents.

→ Indicates a procedure to be carried out.

1.2. Definition of the word "device"

The word "device" used within this manual always refers to the flow-

meter type 8025 or 8035.

1. ABOUT THE QUICKSTART

The quickstart describes the life cycle of the device. Please keep this

manual in a safe place, accessible to all users and any new owners.

Important safety information.

Respect the safety instructions. Study in particular the chapters

entitled Intended Use and Basic Safety Instructions.

• The quickstart must be read and understood.

The quickstart explains how to install, set, and start-up the device.

A detailed description of the device can be found in the related

operating instructions on the delivered CD.

1.1. Symbols used

DANGER

Warns against an imminent danger.

• Failure to observe this warning can result in death or in serious

injury.

AVERTISSEMENT

Warns against a potentially dangerous situation.

• Failure to observe this warning can result in serious injury or even

death.

English

4

Intended use

Type 8025/8035 /

2. INTENDED USE

Use of the device that does not comply with the instructions

could present risks to people, nearby installations and the

environment.

• The compact version of the flowmeter type 8025 or 8035 is

designed to measure the flow rate of a liquid and to totalise the

volume of a liquid.

• The remote version of the flowmeter type 8025 is a transmitter

that must be connected to a 8020 or 8030 flow sensor with a

coil or a pulse output, only in "Low Power" version.

• This device must be protected against electromagnetic interfer-

ence, ultraviolet rays and, when installed outdoors, the effects of

climatic conditions.

• This device must be used in compliance with the characteristics

and commissioning and use conditions specified in the contrac-

tual documents and in the operating instructions.

• Requirements for the safe and proper operation of the device

are proper transport, storage and installation, as well as careful

operation and maintenance.

• Only use the device as intended.

→ Observe any existing restraints when the device is exported.

3. BASIC SAFETY INFORMATION

This safety information does not take into account:

• any contingencies or occurences that may arise during installation,

use and maintenance of the devices.

• the local safety regulations for which the operating company

is responsible including the staff in charge of installation and

maintenance.

Danger due to high pressure in the installation.

• Stop the circulation of fluid, cut off the pressure and drain the

pipe before loosening the process connections.

Danger due to electrical voltage.

• Shut down the electrical power source of all the conductors and

isolate it before carrying out work on the system.

• Observe all applicable accident protection and safety regula-

tions for electrical equipment.

Danger due to high temperatures of the fluid.

• Use safety gloves to handle the device.

• Stop the circulation of fluid and drain the pipe before loosening

the process connections.

Danger due to the nature of the fluid.

• Respect the prevailing regulations on accident prevention and

safety relating to the use of hazardous products.

English

5

Basic safety information

Type 8025/8035 /

Various dangerous situations

To avoid injury take care:

• not to use the device for the measurement of gas flow rates.

• not to use the device in explosive atmospheres.

• not to use the device in an environment incompatible with the

materials it is made of.

• not to subject the device to mechanical loads (e.g. by placing

objects on top of it or by using it as a step).

• not to make any external or internal modifications to the device.

• to prevent any unintentional power supply switch-on.

• to ensure that installation and maintenance work are

carried out by qualified, authorised personnel in possession of

the appropriate tools.

• to guarantee a defined or controlled restarting of the process,

after a power supply interruption.

• to use the device only if in perfect working order and in compli-

ance with the instructions provided in the operating instructions.

• to observe the general technical rules when installing and using

the device.

NOTE

The device may be damaged by the fluid in contact with.

• Systematically check the chemical compatibility of the compo-

nent materials of the device and the fluids likely to come into

contact with it (for example: alcohols, strong or concentrated

acids, aldehydes, alkaline compounds, esters, aliphatic com-

pounds, ketones, halogenated aromatics or hydrocarbons,

oxidants and chlorinated agents).

NOTE

Elements / Components sensitive to electrostatic discharges

• This device contains electronic components sensitive to electro-

static discharges. They may be damaged if they are touched by

an electrostatically charged person or object. In the worst case

scenario, these components are instantly destroyed or go out of

order as soon as they are activated.

• To minimise or even avoid all damage due to an electrostatic

discharge, take all the precautions described in the EN 61340-

5-1 and 5-2 norms.

• Also ensure that you do not touch any of the live electrical

components.

English

6

General information

Type 8025/8035 /

4. GENERAL INFORMATION

4.1. Manufacturer's address and

international contacts

To contact the manufacturer of the device, use following address:

Bürkert SAS

Rue du Giessen

BP 21

F-67220 TRIEMBACH-AU-VAL

You may also contact your local Bürkert sales office.

The addresses of our international sales offices are available on the

internet at: www.burkert.com

4.2. Warranty conditions

The condition governing the legal warranty is the conforming use of

the device type 8025/8035 in observance of the operating condi-

tions specified in this manual.

4.3. Information on the Internet

You can find the operating instructions and technical data sheets

regarding the type 8025 or the type 8035 or at: www.burkert.com.

5. DESCRIPTION OF THE NAME

PLATE

FLOW SE35/8035 HALL SUPPLY: 12-36V ... 70 mA

Output: 1x4-20mA IP65

2xRel: 30V and 42V peak or 60V ... max.

S/N 11 026

00552726

W44MG

Made in France

12

67910

4

8

3

5

1. Measured quantity and type of the device

2. Type of sensor

3. Characteristics of the current output

4. Power supply and maximum of current consumption

5. Protection class of the device

6. Manufacturing code

7. Conformity logo

8. Specification of the relay outputs

9. Serial number

10. Order code

Fig. 1: Name plate of the 8025 / 8035 flowmeter

English

7

Technical data

Type 8025/8035 /

6. TECHNICAL DATA

The following technical data are relevant for a 8025 compact or a

8035 and for the remote 8025 connected to a Bürkert flow sensor

8020 / 8030 in a "Low Power" version only.

6.1. Conditions of use

Ambient temperature

• 8025 compact, 115/230 V AC,

not UR or CSA recognized

• 8035 compact, 115/230 V AC,

not UR or CSA recognized

• other versions, not UR or CSA

recognized

• UR and CSA recognized

versions

• -10 to 50 °C

• -10 to 60 °C

• -10 to 40 °C

Air humidity < 80%, non condensated

Degree of pollution (UR and CSA

recognized versions)

Degree 2 according to EN

61010-1

Installation category (UR and CSA

recognized versions)

Category I according to

UL61010-1

Max. height above sea level 2000 m

Protection rating

• 8025 compact and 8035

• 8025 wall-mounted

• Housing, panel version

• non front parts, panel-mounted

version

According to EN 60529

• IP65, device wired and

cable glands tightened and

cover lid screwed tight.

• IP65, device wired, cable

glands tightened, cover lid

screwed tight and entry

item nuts of the cable

glands tightened at a

screwing torque of 1.5 Nm.

• IP65, installation com-

pleted and closed cabinet

• IP20

6.2. Conformity to standards and

directives

The device conforms to the EC directives through the following

standards:

• EMC: EN 61000-6-2, EN 61000-6-3, EN 550022

• LVD: EN 61010-1

• Environnemental testing: Vibration: EN 60068-2-6, Shock:

EN 60068-2-27.

English

8

Technical data

Type 8025/8035 /

Pressure: article 3§3 of the Pressure Directive 97/23/CE. Acc. to

the Pressure Directive 97/23/CE: the device can only be used in the

following cases (depending on the max. pressure, the DN of the pipe

and the fluid):

Type of fluid Conditions

8025 8035

1)

Fluid group 1, par.

1.3.a

DN25 only DN ≤ 25 only

Fluid group 2 par. 1.3.a

DN ≤ 32

or DN > 32 and

PNxDN ≤ 1000

DN ≤ 32

or DN > 32 and

PNxDN ≤ 1000

Fluid group 1 par. 1.3.b

DN ≤ 25

or DN > 25 and

PNxDN ≤ 2000

Fluid group 2 par. 1.3.b DN ≤ 400 DN ≤ 200

1)

For the type 8035: S030 sensor-fitting, DN6 to DN65, in PP, PVC,

PVDF, brass or stainless steel.

The UL recognized devices with variable key PU01 comply with the fol-

lowing standards:

• UL 61010-1

• CAN/CSA-C22.2 n° 61010-1

6.3. General data

Pipe diameter

• 8025 flowmeter

• 8025 transmitter (remote

versions)

• 8035 flowmeter

• DN20 (except for the DN

specified p.15) to DN400

• DN06 to DN400

• DN06 to DN65

Type of fitting • S020, for a compact 8025

• S030, for a 8035

Type of fluid • liquid

• viscosity: max. 300 cSt

• rate of solid particles: max.

1%

Fluid temperature (compact ver-

sions)

• with fitting in PVC

• with fitting in PP

• with fitting in PVDF, stainless

steel or brass

The fluid temperature may be

restricted by the fluid pressure,

the material the flow sensor is

made of and the material the

S020 or S030 fitting used is

made of. See "Fig. 2" and "Fig.

3".

• 0 to +50 °C

• 0 to +80 °C

• -15 to +80 °C

English

9

Technical data

Type 8025/8035 /

Fluid pressure (compact ver-

sions)

• 8025 compact

• 8035 with S030 fitting in

plastic

• 8035 with S030 fitting in metal

The fluid pressure may be

restricted by the fluid tem-

perature, the material the flow

sensor is made of (only for the

compact 8025) and the material

the fitting used is made of. See

"Fig. 2" and "Fig. 3".

• PN10

• PN16 (PN40 on request)

Flow rate measurement

• Measurement range

- Sensor with pulse output

(Hall)

- Sensor with a sinus output

(coil)

• Accuracy

- with a teach-in procedure

- with the K factor of the

fitting used

• Linearity

1)

• Repeatability

1)

- 0.3 m/s to 10 m/s

- 0.5 m/s to 10 m/s

- 1 % of the measured value

(at the value of the teach-in

flow rate)

- 2,5 % of the measured

value

• ±0,5 % of the full scale

• ±0,4 % of the measured value

1)

Determined in the following reference conditions: medium = water, water

and ambient temperatures 20 °C, min. upstream and downstream distances

respected, appropriate pipe dimensions

10

9

8

7

6

5

4

3

2

1

0

-15 0 +20 +40 +60

PVDF

PVDF (PN10)

PVC (PN10)

PP (PN10)

PVC + PP

11

P (bar)

T (°C)

+80

A

Metal

A: range of use

Fig. 2: Fluid temperature /pressure dependency curves for the

8025 compact version, depending on the material the

S020 fitting is made of

English

10

Technical data

Type 8025/8035 /

10

9

8

7

6

5

4

3

2

1

0

-30

-10 +10 +30 +50 +70 +90 +110

PVDF (PN10)

PVC (PN10)

PP (PN10)

PVC + PP

PVDF

16

15

14

13

12

11

A

P (bar)

T °C

A

Metal

A: range of use

Fig. 3: Fluid temperature /pressure dependency curves for the

8035 compact version, depending on the material the

S030 fitting is made of

6.4. Mechanical data

Part Material

Sensor holder - Paddle-wheel

• 8025, compact versions

• 8025, remote versions

• 8035

• PVDF

• Refer to the operating instruc-

tions of the remote sensor

• Refer to the operating instruc-

tions of the S030 sensor-fitting

Axis and bearings of the

paddle-wheel

• 8025, compact versions

• 8025, remote versions

• 8035

• Ceramics

• Refer to the operating instruc-

tions of the remote sensor

• Refer to the operating instruc-

tions of the S030 sensor-fitting

Seals

• 8025, compact versions

• 8025, remote versions

• FKM (EPDM delivered with the

device)

• Refer to the operating instruc-

tions of the remote sensor

Nut

• 8025, compact versions • PC

English

11

Technical data

Type 8025/8035 /

Part Material

Housing

• 8025, compact or remote

versions

• 8025, wall-mounted versions

• 8035

• PC

• ABS

• PC

Cover

• 8025 compact versions or

8035

• 8025 panel versions

• 8025, wall-mounted versions

• PC (Cover with lid)

• PC

• ABS

Front foil Polyester

Screws (4) Stainless steel

Male fixed connector and

female connector (type 2508)

PA

Cable glands PA

6.5. Electrical data

Power supply 12-36 V DC • filtered and regulated

• SELV circuit (safety extra low

voltage), with a safe energy

level

• oscillation rate: ±10 %

Power supply (not supplied) • limited power source

according to § 9.3 of

EN 61010-1 standard

• or class 2 source according

to UL 1310/1585 and

EN 60950-1 standards

Power supply 115/230 V AC

• frequency

• supplied voltage

• current

• integrated protection

• power

• 50/60 Hz

• 27 V DC, regulated

• max. 250 mA

• 250 mA time-delay fuse

• Compact version: 6 VA

• Wall-mounted version 3 VA

Current consumption (without the

consumption of the 4-20 mA output)

• 12-36 V DC version with relays

• 12-36 V DC version without

relays

• 115/230 V AC compact version

• 115/230 V AC wall-mounted

version

• 70 mA max. (at 12 V DC)

• 25 mA max. (at 12 V DC)

• 125 mA max. (at 27 V DC)

• 250 mA max. (at 27 V DC)

English

12

Technical data

Type 8025/8035 /

Pulse output

• type

• function

• frequency (f)

• electrical data

• duty cycle

• protection

polarized, potential-free

• NPN/PNP (wiring dependant)

• pulse output, adjustable pulse

value

• 2,5-400 Hz

• 5-36 V DC, 100 mA max.,

voltage drop 2,5 V DC at

100 mA

• 0,5

• galvanically isolated, and

protected against over-

voltages, polarity reversals

and short-circuits

Relay outputs

• operating

• electrical data of the load (non

UL recognized devices)

• electrical data of the load (UL

recognized devices)

• hysteresis, adjustable

thresholds, normally open

• 230 V AC / 3 A

• 30 V AC max. and 42 V peak

or 60 V DC max.

Current output

• response time (10% to 90%)

• max. loop impedance,

12-36 V DC version

• max. loop impedance,

115/230 V AC version

• wiring, version without relays

• wiring, version with relays

4-20 mA, sinking or sourcing

mode (through wiring)

• 5,75 s (default)

• 900W at 30 V DC, 600W at

24 V DC, 50 W at 12 V DC

• 800 W

• 2-wire

• 3-wire

Protection against polarity

reversals

yes

6.6. Specifications of the connected

flow sensor

Sensor input

• signal frequency

• pulse signal (Hall)

• sinus signal (coil)

• 2,5 to 400 Hz

• NPN, open collector

• typical sensitivity of 35 mV peak-

peak, at 252 Hz

Sensor output

• power supply • 10-34 V DC (V+ subtract 2

V DC), 1 mA max.

English

13

Installation

Type 8025/8035 /

7. INSTALLATION

7.1. Safety instructions

DANGER

Risk of injury due to electrical voltage.

• Shut down the electrical power source of all the conductors and

isolate it before carrying out work on the system.

• Observe all applicable accident protection and safety regulations for

electrical equipment.

WARNING

Risk of injury due to non-conforming installation.

• The electrical and fluid installation can only be carried out by quali-

fied and skilled staff with the appropriate tools.

• Install appropriate safety devices (correctly rated fuse and/

or circuit-breaker); for the versions with 115/230 V AC power

supply, insert a protection device between phase and neutral.

• Respect standard NF C 15-100 / IEC 60364.

• Observe mounting instructions of the fitting.

Risk of injury due to unintentional switch on of power supply

or uncontrolled restarting of the installation.

• Take appropriate measures to avoid unintentional activation of the

installation.

• Guarantee a set or controlled restarting of the process subse-

quent to any intervention on the device.

6.7. Electrical connection

Version Wiring features

With male fixed

connector

Female connector (type 2508 supplied)

For the female connector type 2508 with

order code 438811 and the female con-

nector type 2509 (not supplied) with order

code 162673, use a shielded cable.

• external diameter of the cable: 5 to 8 mm

• cross section of the wires: 0.2 to

1.5 mm

2

• max. length of the power supply, current

output and pulse output connection

cables: 50 m

With terminal strip,

with or without cable

glands

Shielded cable (not supplied):

• external diameter of the cable: 6 to

12 mm (4 to 6 mm when using a mul-

tiway seal)

• cross section of the wires: 0.2 to

1.5 mm

2

All Cross section of the local earthing wire:

0.75 mm

2

English

14

Installation

Type 8025/8035 /

WARNING

Risk of injury if the fluid pressure/ temperature dependency

is not respected.

• Take account of fluid temperature-pressure dependancy

according to the nature of the materials the fitting is made of

(see the technical data and the operating instructions of the

fitting used).

• Comply with the Pressure Directive 97/23/EC.

Protect this device against electromagnetic inter-

ference, ultraviolet rays and, when installed outdoors,

the effects of the climatic conditions.

7.2. Installation of a compact version

7.2.1. Instructions for installing a compact

version onto the pipe

The 8025 flowmeter has to be inserted into an S020 fitting mounted

on a pipe.

The 8035 flowmeter has to be installed on the pipe using the S030

sensor-fitting.

→ Choose an S020 or S030 fitting appropriate to the velocity of

the fluid inside the pipe: refer to the graphs below:

English

15

Installation

Type 8025/8035 /

Table 1: Flow rate/ fluid velocity/ DN of S020 fitting and of S030 sensor-fitting diagram

S020 fitting

0.10.3 0.51 35 10

0.01

0.02

0.05

0.1

0.2

0.5

1

2

5

10

20

50

100

200

m

3

/h

0.2

0.5

1

2

5

10

20

50

100

200

500

1000

2000

3000

l/min

0.3

0.51 35 10

30

m/s

fps

US gpm

0.05

0.1

0.2

0.5

1

2

5

10

20

50

100

200

500

1000

DN 65

DN 50 (DN65)*

DN 40 (DN50)*

DN 32 (DN40)*

DN 25 (DN32)*

DN 20 (DN25)*

500

1000

2000

5000

10000

5000

20000

5000

10000

20000

30000

50000

100000

DN 400

DN 350

DN 300

DN 250

DN 200

DN 150

DN 125

DN 100

DN 80

Flow rate

Flow velocity

Example

1)

S030 sensor-fitting

0.10.3 0.51 35 10

0.01

0.02

0.05

0.1

0.2

0.5

1

2

5

10

20

50

100

200

m

3

/h

l/min

0.30.5 13510

30

m/s

fps

gpm

0.05

0.1

0.2

0.5

1

2

5

10

20

50

100

200

500

1000

DN65

DN50 (DN65)*

DN40 (DN50)*

DN32 (DN40)*

DN25 (DN32)*

DN20 (DN25)*

DN15 (DN15 / DN20)*

DN08

DN06

0.2

0.5

1

2

5

10

20

50

100

200

500

1000

2000

3000

Example

Flow rate

Flow velocity

Example:

• Specification: if the nominal flow

rate is 10 m

3

/h, the ideal flow

velocity is between 2 and 3 m/s.

• Solution: intersection between

flow rate and flow velocity in the

graph gives the appropriate pipe

diameter, DN40 (or DN50 for

the asterisked fittings).

1)

The device cannot be installed

onto the following DN20 fittings:

* For the fittings:

• with external threads acc. to

SMS 1145.

• with weld ends

acc. to SMS 3008,

BS 4825 / ASME BPE or

DIN 11850 Rg2.

• Clamp acc. to

SMS 3017 / ISO 2852,

BS 4825 / ASME BPE or

DIN 32676.

English

16

Installation

Type 8025/8035 /

→ Install the device on the pipe in such a way that the upstream and

downstream distances are respected according to the design of

the pipes, refer to standard EN ISO 5167-1 and "Fig. 4":

flow direction

50 x DN 5 x DN

40 x DN 5 x DN

25 x DN 5 x DN 20 x DN 5 x DN

18 x DN 5 x DN 15 x DN 5 x DN

With control valve Pipe with 2 elbows at 90° in 3

dimensions

Pipe with 2 elbows at 90° Pipe with 1 elbow at 90° or 1

T-piece

With pipe expansion With pipe reduction

Fig. 4: Upstream and downstream distances depending on the

design of the pipes

→ Ensure that the pipe is always filled in the section around the

device (see "Fig. 5").

→ When mounting vertically ensure that the flow direction is in an

upward direction (see "Fig. 5").

Horizontal mounting

Correct Incorrect

Vertical mounting

Correct Incorrect

flow direction

Fig. 5: Filling of the pipe

→ Prevent the formation of air bubbles in the pipe in the section

around the device (see "Fig. 6").

English

17

Installation

Type 8025/8035 /

Correct

flow direction

Incorrect

Correct Incorrect

Fig. 6: Air bubbles within the pipe

→ If necessary, use a flow conditioner to improve measurement

accuracy.

7.2.2. Installation of the 8025 on the S020

fitting

2

1

3

4

5

6

→ Install the S020 fitting into the pipe

obeying the instructions in chap. "7.2.1"

→ Check that there is a seal on the fitting

and that it is not damaged. Replace the

seal if necessary.

→ Insert nut 3 on fitting 5.

→ Insert snap ring 2 into groove 4.

→ Check that seal 6 is correctly inserted on

the flow sensor.

→ Insert device 1 into the fitting.

If the mounting is correctly done the device

cannot be turned around anymore.

→ Hand lock the assembly with nut 3.

Fig. 7: Installation of the 8025 on the S020 fitting

English

18

Installation

Type 8025/8035 /

7.2.3. Installation of the SE35 electronic

module onto the S030 sensor-fitting

1

2

3

→ Respect the installation

instructions contained

in the operating instruc-

tions of the fitting used.

→ Insert the electronic

module 2 into the S030

sensor-fitting.

→ Fix with a 30° rotation.

→ Tighten the side screw

3 to lock the elec-

tronic module to the

sensor-fitting.

Fig. 8: Installation of the SE35 onto the S030 sensor-fitting

7.3. Installation of a panel version of

the 8025 flowmeter

Install the panel version of the device in a cabinet with

a protection class at least IP54 to ensure a degree of

pollution 2 inside the cabinet.

→ To cut the opening in the cabinet door, use the supplied cutting

plan of the frontage of the electrical cabinet, respecting the

dimensions indicated in "Fig. 9".

95

80

76

50

95

80

76

50

Fig. 9: Dimensions [mm] of the electrical cabinet frontage cutting

plan

English

19

Installation

Type 8025/8035 /

Seal

Nut

Washer

Screw

Cable clip

Fig. 10: Installation of a panel version of the 8025

→ Insert the 4 screws in the housing (from the front). Use the 4

supplied M4*25 screws if the cabinet door is too thick.

→ Insert the seal on the external threads of the 4 screws (rear of

the housing).

→ Put the assembly on the cutout, electronics turned to the inside

of the cabinet.

→ Put the 4 washers on the 4 screws.

→ Put a nut on each of the 4 screws and tighten the nuts to secure

the device to the cabinet.

→ Wire according to the instructions in chapter "8".

7.4. Installation of a wall-mounted

version of the 8025 flowmeter

NOTE

Risk of material damage if the cable glands are not tightly

screwed on the housing

• Before installing the wall-mounted housing on its support,

tighten the nuts of the entry item of the cables glands at a torque

of 1.5 Nm.

The flow transmitter in a wall-mounted version has 4 holes in the

bottom of the housing.

→ Remove the blanking strips covering the screws.

Blanking strips

ENTER

0....9

FLOW

Nut of the entry item

→ Loosen the 4 screws and open the cover to get access to the

holes [1].

English

20

Wiring

Type 8025/8035 /

1

230V

LN

230V

T 250 mA

56789 10

LN

230V

NPN SENSOR

1 PULSE INPUT

2 -

3 +

4 NC

SUPPLY

1234PE

3A/230VAC

REL1

REL2

FLOW SENSOR

COILNPN

CURRENT

SOURCE SINK

COIL SENSOR

1

2

3 NC

4 NC

L+

L-

PE

P-

P+

NC

L+

L-

PE

P-

P+

Iout

PULSE

OUTPUT

Without

With

Relays

Supply

12..36Vdc

106 mm

Fig. 11: Installation of a wall-mounted version

→ Secure the housing to the support respecting the dimensions

indicated in "Fig. 11".

→ Wire acc. to instructions in chap. "8".

→ Close the housing and tighten the 4 screws of the cover.

8. WIRING

DANGER

Risk of injury due to electrical voltage.

• Shut down the electrical power source of all the conductors and

isolate it before carrying out work on the system.

• Observe all applicable accident protection and safety regula-

tions for electrical equipment.

Insert the supplied stopper gaskets into the unused cable

glands of a compact or a wall-mounted version to ensure

the tightness of the device.

Only move the selectors when the power supply is off.

English

La page charge ...

Burkert 8025 Series Guide de démarrage rapide

Ce manuel convient également à

Burkert 8025 Series Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents