Burkert 8025 Series Guide de démarrage rapide

Taper
Guide de démarrage rapide

Ce manuel convient également à

Quickstart
Type 8025 / 8035
Flowmeter
English
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Subject to technical changes.
© Bürkert SAS, 2013
Quickstart 1312/0_EU-ML 00565666 ORIGINAL_FR
1. ABOUT THE QUICKSTART.........................................................................3
2. INTENDED USE ................................................................................................4
3. BASIC SAFETY INFORMATION ...............................................................4
4. GENERAL INFORMATION ...........................................................................6
5. DESCRIPTION OF THE NAME PLATE ..................................................6
6. TECHNICAL DATA ...........................................................................................7
7. INSTALLATION ...............................................................................................13
8. WIRING ...............................................................................................................20
9. INSTALLATION AND COMMISSIONING ...........................................49
10. MAINTENANCE AND TROUBLESHOOTING ................................ 55
11. PACKAGING, TRANSPORT ...................................................................55
13. DISPOSAL OF THE PRODUCT ........................................................... 56
3
About the Quickstart
Type 8025/8035 /
ATTENTION
Warns against a possible risk.
Failure to observe this warning can result in substantial or minor
injuries.
NOTE
Warns against material damage.
Failure to observe this warning may result in damage to the
device or system.
indicates additional information, advice or important
recommendations.
refers to information contained in this manual or in other
documents.
Indicates a procedure to be carried out.
1.2. Definition of the word "device"
The word "device" used within this manual always refers to the flow-
meter type 8025 or 8035.
1. ABOUT THE QUICKSTART
The quickstart describes the life cycle of the device. Please keep this
manual in a safe place, accessible to all users and any new owners.
Important safety information.
Respect the safety instructions. Study in particular the chapters
entitled Intended Use and Basic Safety Instructions.
The quickstart must be read and understood.
The quickstart explains how to install, set, and start-up the device.
A detailed description of the device can be found in the related
operating instructions on the delivered CD.
1.1. Symbols used
DANGER
Warns against an imminent danger.
Failure to observe this warning can result in death or in serious
injury.
AVERTISSEMENT
Warns against a potentially dangerous situation.
Failure to observe this warning can result in serious injury or even
death.
English
4
Intended use
Type 8025/8035 /
2. INTENDED USE
Use of the device that does not comply with the instructions
could present risks to people, nearby installations and the
environment.
The compact version of the flowmeter type 8025 or 8035 is
designed to measure the flow rate of a liquid and to totalise the
volume of a liquid.
The remote version of the flowmeter type 8025 is a transmitter
that must be connected to a 8020 or 8030 flow sensor with a
coil or a pulse output, only in "Low Power" version.
This device must be protected against electromagnetic interfer-
ence, ultraviolet rays and, when installed outdoors, the effects of
climatic conditions.
This device must be used in compliance with the characteristics
and commissioning and use conditions specified in the contrac-
tual documents and in the operating instructions.
Requirements for the safe and proper operation of the device
are proper transport, storage and installation, as well as careful
operation and maintenance.
Only use the device as intended.
Observe any existing restraints when the device is exported.
3. BASIC SAFETY INFORMATION
This safety information does not take into account:
any contingencies or occurences that may arise during installation,
use and maintenance of the devices.
the local safety regulations for which the operating company
is responsible including the staff in charge of installation and
maintenance.
Danger due to high pressure in the installation.
Stop the circulation of fluid, cut off the pressure and drain the
pipe before loosening the process connections.
Danger due to electrical voltage.
Shut down the electrical power source of all the conductors and
isolate it before carrying out work on the system.
Observe all applicable accident protection and safety regula-
tions for electrical equipment.
Danger due to high temperatures of the fluid.
Use safety gloves to handle the device.
Stop the circulation of fluid and drain the pipe before loosening
the process connections.
Danger due to the nature of the fluid.
Respect the prevailing regulations on accident prevention and
safety relating to the use of hazardous products.
English
5
Basic safety information
Type 8025/8035 /
Various dangerous situations
To avoid injury take care:
not to use the device for the measurement of gas flow rates.
not to use the device in explosive atmospheres.
not to use the device in an environment incompatible with the
materials it is made of.
not to subject the device to mechanical loads (e.g. by placing
objects on top of it or by using it as a step).
not to make any external or internal modifications to the device.
to prevent any unintentional power supply switch-on.
to ensure that installation and maintenance work are
carried out by qualified, authorised personnel in possession of
the appropriate tools.
to guarantee a defined or controlled restarting of the process,
after a power supply interruption.
to use the device only if in perfect working order and in compli-
ance with the instructions provided in the operating instructions.
to observe the general technical rules when installing and using
the device.
NOTE
The device may be damaged by the fluid in contact with.
Systematically check the chemical compatibility of the compo-
nent materials of the device and the fluids likely to come into
contact with it (for example: alcohols, strong or concentrated
acids, aldehydes, alkaline compounds, esters, aliphatic com-
pounds, ketones, halogenated aromatics or hydrocarbons,
oxidants and chlorinated agents).
NOTE
Elements / Components sensitive to electrostatic discharges
This device contains electronic components sensitive to electro-
static discharges. They may be damaged if they are touched by
an electrostatically charged person or object. In the worst case
scenario, these components are instantly destroyed or go out of
order as soon as they are activated.
To minimise or even avoid all damage due to an electrostatic
discharge, take all the precautions described in the EN 61340-
5-1 and 5-2 norms.
Also ensure that you do not touch any of the live electrical
components.
English
6
General information
Type 8025/8035 /
4. GENERAL INFORMATION
4.1. Manufacturer's address and
international contacts
To contact the manufacturer of the device, use following address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220 TRIEMBACH-AU-VAL
You may also contact your local Bürkert sales office.
The addresses of our international sales offices are available on the
internet at: www.burkert.com
4.2. Warranty conditions
The condition governing the legal warranty is the conforming use of
the device type 8025/8035 in observance of the operating condi-
tions specified in this manual.
4.3. Information on the Internet
You can find the operating instructions and technical data sheets
regarding the type 8025 or the type 8035 or at: www.burkert.com.
5. DESCRIPTION OF THE NAME
PLATE
FLOW SE35/8035 HALL SUPPLY: 12-36V ... 70 mA
Output: 1x4-20mA IP65
2xRel: 30V and 42V peak or 60V ... max.
S/N 11 026
00552726
W44MG
Made in France
12
67910
4
8
3
5
1. Measured quantity and type of the device
2. Type of sensor
3. Characteristics of the current output
4. Power supply and maximum of current consumption
5. Protection class of the device
6. Manufacturing code
7. Conformity logo
8. Specification of the relay outputs
9. Serial number
10. Order code
Fig. 1: Name plate of the 8025 / 8035 flowmeter
English
7
Technical data
Type 8025/8035 /
6. TECHNICAL DATA
The following technical data are relevant for a 8025 compact or a
8035 and for the remote 8025 connected to a Bürkert flow sensor
8020 / 8030 in a "Low Power" version only.
6.1. Conditions of use
Ambient temperature
8025 compact, 115/230 V AC,
not UR or CSA recognized
8035 compact, 115/230 V AC,
not UR or CSA recognized
other versions, not UR or CSA
recognized
UR and CSA recognized
versions
-10 to 50 °C
-10 to 50 °C
-10 to 60 °C
-10 to 40 °C
Air humidity < 80%, non condensated
Degree of pollution (UR and CSA
recognized versions)
Degree 2 according to EN
61010-1
Installation category (UR and CSA
recognized versions)
Category I according to
UL61010-1
Max. height above sea level 2000 m
Protection rating
8025 compact and 8035
8025 wall-mounted
Housing, panel version
non front parts, panel-mounted
version
According to EN 60529
IP65, device wired and
cable glands tightened and
cover lid screwed tight.
IP65, device wired, cable
glands tightened, cover lid
screwed tight and entry
item nuts of the cable
glands tightened at a
screwing torque of 1.5 Nm.
IP65, installation com-
pleted and closed cabinet
IP20
6.2. Conformity to standards and
directives
The device conforms to the EC directives through the following
standards:
EMC: EN 61000-6-2, EN 61000-6-3, EN 550022
LVD: EN 61010-1
Environnemental testing: Vibration: EN 60068-2-6, Shock:
EN 60068-2-27.
English
8
Technical data
Type 8025/8035 /
Pressure: article 3§3 of the Pressure Directive 97/23/CE. Acc. to
the Pressure Directive 97/23/CE: the device can only be used in the
following cases (depending on the max. pressure, the DN of the pipe
and the fluid):
Type of fluid Conditions
8025 8035
1)
Fluid group 1, par.
1.3.a
DN25 only DN 25 only
Fluid group 2 par. 1.3.a
DN 32
or DN > 32 and
PNxDN 1000
DN 32
or DN > 32 and
PNxDN 1000
Fluid group 1 par. 1.3.b
DN 25
or DN > 25 and
PNxDN 2000
PNxDN 2000
Fluid group 2 par. 1.3.b DN 400 DN 200
1)
For the type 8035: S030 sensor-fitting, DN6 to DN65, in PP, PVC,
PVDF, brass or stainless steel.
The UL recognized devices with variable key PU01 comply with the fol-
lowing standards:
UL 61010-1
CAN/CSA-C22.2 n° 61010-1
6.3. General data
Pipe diameter
8025 flowmeter
8025 transmitter (remote
versions)
8035 flowmeter
DN20 (except for the DN
specified p.15) to DN400
DN06 to DN400
DN06 to DN65
Type of fitting S020, for a compact 8025
S030, for a 8035
Type of fluid liquid
viscosity: max. 300 cSt
rate of solid particles: max.
1%
Fluid temperature (compact ver-
sions)
with fitting in PVC
with fitting in PP
with fitting in PVDF, stainless
steel or brass
The fluid temperature may be
restricted by the fluid pressure,
the material the flow sensor is
made of and the material the
S020 or S030 fitting used is
made of. See "Fig. 2" and "Fig.
3".
0 to +50 °C
0 to +80 °C
-15 to +80 °C
English
9
Technical data
Type 8025/8035 /
Fluid pressure (compact ver-
sions)
8025 compact
8035 with S030 fitting in
plastic
8035 with S030 fitting in metal
The fluid pressure may be
restricted by the fluid tem-
perature, the material the flow
sensor is made of (only for the
compact 8025) and the material
the fitting used is made of. See
"Fig. 2" and "Fig. 3".
PN10
PN10
PN16 (PN40 on request)
Flow rate measurement
Measurement range
- Sensor with pulse output
(Hall)
- Sensor with a sinus output
(coil)
Accuracy
- with a teach-in procedure
- with the K factor of the
fitting used
Linearity
1)
Repeatability
1)
- 0.3 m/s to 10 m/s
- 0.5 m/s to 10 m/s
- 1 % of the measured value
(at the value of the teach-in
flow rate)
- 2,5 % of the measured
value
±0,5 % of the full scale
±0,4 % of the measured value
1)
Determined in the following reference conditions: medium = water, water
and ambient temperatures 20 °C, min. upstream and downstream distances
respected, appropriate pipe dimensions
10
9
8
7
6
5
4
3
2
1
0
-15 0 +20 +40 +60
PVDF
PVDF (PN10)
PVC (PN10)
PP (PN10)
PVC + PP
11
P (bar)
T (°C)
+80
A
Metal
A: range of use
Fig. 2: Fluid temperature /pressure dependency curves for the
8025 compact version, depending on the material the
S020 fitting is made of
English
10
Technical data
Type 8025/8035 /
10
9
8
7
6
5
4
3
2
1
0
-30
-10 +10 +30 +50 +70 +90 +110
PVDF (PN10)
PVC (PN10)
PP (PN10)
PVC + PP
PVDF
16
15
14
13
12
11
A
P (bar)
T °C
A
Metal
A: range of use
Fig. 3: Fluid temperature /pressure dependency curves for the
8035 compact version, depending on the material the
S030 fitting is made of
6.4. Mechanical data
Part Material
Sensor holder - Paddle-wheel
8025, compact versions
8025, remote versions
8035
PVDF
Refer to the operating instruc-
tions of the remote sensor
Refer to the operating instruc-
tions of the S030 sensor-fitting
Axis and bearings of the
paddle-wheel
8025, compact versions
8025, remote versions
8035
Ceramics
Refer to the operating instruc-
tions of the remote sensor
Refer to the operating instruc-
tions of the S030 sensor-fitting
Seals
8025, compact versions
8025, remote versions
FKM (EPDM delivered with the
device)
Refer to the operating instruc-
tions of the remote sensor
Nut
8025, compact versions PC
English
11
Technical data
Type 8025/8035 /
Part Material
Housing
8025, compact or remote
versions
8025, wall-mounted versions
8035
PC
ABS
PC
Cover
8025 compact versions or
8035
8025 panel versions
8025, wall-mounted versions
PC (Cover with lid)
PC
ABS
Front foil Polyester
Screws (4) Stainless steel
Male fixed connector and
female connector (type 2508)
PA
Cable glands PA
6.5. Electrical data
Power supply 12-36 V DC filtered and regulated
SELV circuit (safety extra low
voltage), with a safe energy
level
oscillation rate: ±10 %
Power supply (not supplied) limited power source
according to § 9.3 of
EN 61010-1 standard
or class 2 source according
to UL 1310/1585 and
EN 60950-1 standards
Power supply 115/230 V AC
frequency
supplied voltage
current
integrated protection
power
50/60 Hz
27 V DC, regulated
max. 250 mA
250 mA time-delay fuse
Compact version: 6 VA
Wall-mounted version 3 VA
Current consumption (without the
consumption of the 4-20 mA output)
12-36 V DC version with relays
12-36 V DC version without
relays
115/230 V AC compact version
115/230 V AC wall-mounted
version
70 mA max. (at 12 V DC)
25 mA max. (at 12 V DC)
125 mA max. (at 27 V DC)
250 mA max. (at 27 V DC)
English
12
Technical data
Type 8025/8035 /
Pulse output
type
function
frequency (f)
electrical data
duty cycle
protection
polarized, potential-free
NPN/PNP (wiring dependant)
pulse output, adjustable pulse
value
2,5-400 Hz
5-36 V DC, 100 mA max.,
voltage drop 2,5 V DC at
100 mA
0,5
galvanically isolated, and
protected against over-
voltages, polarity reversals
and short-circuits
Relay outputs
operating
electrical data of the load (non
UL recognized devices)
electrical data of the load (UL
recognized devices)
hysteresis, adjustable
thresholds, normally open
230 V AC / 3 A
30 V AC max. and 42 V peak
or 60 V DC max.
Current output
response time (10% to 90%)
max. loop impedance,
12-36 V DC version
max. loop impedance,
115/230 V AC version
wiring, version without relays
wiring, version with relays
4-20 mA, sinking or sourcing
mode (through wiring)
5,75 s (default)
900W at 30 V DC, 600W at
24 V DC, 50 W at 12 V DC
800 W
2-wire
3-wire
Protection against polarity
reversals
yes
6.6. Specifications of the connected
flow sensor
Sensor input
signal frequency
pulse signal (Hall)
sinus signal (coil)
2,5 to 400 Hz
NPN, open collector
typical sensitivity of 35 mV peak-
peak, at 252 Hz
Sensor output
power supply 10-34 V DC (V+ subtract 2
V DC), 1 mA max.
English
13
Installation
Type 8025/8035 /
7. INSTALLATION
7.1. Safety instructions
DANGER
Risk of injury due to electrical voltage.
Shut down the electrical power source of all the conductors and
isolate it before carrying out work on the system.
Observe all applicable accident protection and safety regulations for
electrical equipment.
WARNING
Risk of injury due to non-conforming installation.
The electrical and fluid installation can only be carried out by quali-
fied and skilled staff with the appropriate tools.
Install appropriate safety devices (correctly rated fuse and/
or circuit-breaker); for the versions with 115/230 V AC power
supply, insert a protection device between phase and neutral.
Respect standard NF C 15-100 / IEC 60364.
Observe mounting instructions of the fitting.
Risk of injury due to unintentional switch on of power supply
or uncontrolled restarting of the installation.
Take appropriate measures to avoid unintentional activation of the
installation.
Guarantee a set or controlled restarting of the process subse-
quent to any intervention on the device.
6.7. Electrical connection
Version Wiring features
With male fixed
connector
Female connector (type 2508 supplied)
For the female connector type 2508 with
order code 438811 and the female con-
nector type 2509 (not supplied) with order
code 162673, use a shielded cable.
external diameter of the cable: 5 to 8 mm
cross section of the wires: 0.2 to
1.5 mm
2
max. length of the power supply, current
output and pulse output connection
cables: 50 m
With terminal strip,
with or without cable
glands
Shielded cable (not supplied):
external diameter of the cable: 6 to
12 mm (4 to 6 mm when using a mul-
tiway seal)
cross section of the wires: 0.2 to
1.5 mm
2
All Cross section of the local earthing wire:
0.75 mm
2
English
14
Installation
Type 8025/8035 /
WARNING
Risk of injury if the fluid pressure/ temperature dependency
is not respected.
Take account of fluid temperature-pressure dependancy
according to the nature of the materials the fitting is made of
(see the technical data and the operating instructions of the
fitting used).
Comply with the Pressure Directive 97/23/EC.
Protect this device against electromagnetic inter-
ference, ultraviolet rays and, when installed outdoors,
the effects of the climatic conditions.
7.2. Installation of a compact version
7.2.1. Instructions for installing a compact
version onto the pipe
The 8025 flowmeter has to be inserted into an S020 fitting mounted
on a pipe.
The 8035 flowmeter has to be installed on the pipe using the S030
sensor-fitting.
Choose an S020 or S030 fitting appropriate to the velocity of
the fluid inside the pipe: refer to the graphs below:
English
15
Installation
Type 8025/8035 /
Table 1: Flow rate/ fluid velocity/ DN of S020 fitting and of S030 sensor-fitting diagram
S020 fitting
0.10.3 0.51 35 10
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
10
20
50
100
200
m
3
/h
0.2
0.5
1
2
5
10
20
50
100
200
500
1000
2000
3000
l/min
0.3
0.51 35 10
30
m/s
fps
US gpm
0.05
0.1
0.2
0.5
1
2
5
10
20
50
100
200
500
1000
DN 65
DN 50 (DN65)*
DN 40 (DN50)*
DN 32 (DN40)*
DN 25 (DN32)*
DN 20 (DN25)*
500
1000
2000
2000
5000
10000
5000
20000
5000
10000
20000
30000
50000
100000
DN 400
DN 350
DN 300
DN 250
DN 200
DN 150
DN 125
DN 100
DN 80
Flow rate
Flow velocity
Example
1)
S030 sensor-fitting
0.10.3 0.51 35 10
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
10
20
50
100
200
m
3
/h
l/min
0.30.5 13510
30
m/s
fps
gpm
0.05
0.1
0.2
0.5
1
2
5
10
20
50
100
200
500
1000
DN65
DN50 (DN65)*
DN40 (DN50)*
DN32 (DN40)*
DN25 (DN32)*
DN20 (DN25)*
DN15 (DN15 / DN20)*
DN08
DN06
0.2
0.5
1
2
5
10
20
50
100
200
500
1000
2000
3000
Example
Flow rate
Flow velocity
Example:
Specification: if the nominal flow
rate is 10 m
3
/h, the ideal flow
velocity is between 2 and 3 m/s.
Solution: intersection between
flow rate and flow velocity in the
graph gives the appropriate pipe
diameter, DN40 (or DN50 for
the asterisked fittings).
1)
The device cannot be installed
onto the following DN20 fittings:
* For the fittings:
with external threads acc. to
SMS 1145.
with weld ends
acc. to SMS 3008,
BS 4825 / ASME BPE or
DIN 11850 Rg2.
Clamp acc. to
SMS 3017 / ISO 2852,
BS 4825 / ASME BPE or
DIN 32676.
English
16
Installation
Type 8025/8035 /
Install the device on the pipe in such a way that the upstream and
downstream distances are respected according to the design of
the pipes, refer to standard EN ISO 5167-1 and "Fig. 4":
flow direction
50 x DN 5 x DN
40 x DN 5 x DN
25 x DN 5 x DN 20 x DN 5 x DN
18 x DN 5 x DN 15 x DN 5 x DN
With control valve Pipe with 2 elbows at 90° in 3
dimensions
Pipe with 2 elbows at 90° Pipe with 1 elbow at 90° or 1
T-piece
With pipe expansion With pipe reduction
Fig. 4: Upstream and downstream distances depending on the
design of the pipes
Ensure that the pipe is always filled in the section around the
device (see "Fig. 5").
When mounting vertically ensure that the flow direction is in an
upward direction (see "Fig. 5").
Horizontal mounting
Correct Incorrect
Vertical mounting
Correct Incorrect
flow direction
Fig. 5: Filling of the pipe
Prevent the formation of air bubbles in the pipe in the section
around the device (see "Fig. 6").
English
17
Installation
Type 8025/8035 /
Correct
flow direction
Incorrect
Correct Incorrect
Fig. 6: Air bubbles within the pipe
If necessary, use a flow conditioner to improve measurement
accuracy.
7.2.2. Installation of the 8025 on the S020
fitting
2
1
3
4
5
6
Install the S020 fitting into the pipe
obeying the instructions in chap. "7.2.1"
Check that there is a seal on the fitting
and that it is not damaged. Replace the
seal if necessary.
Insert nut 3 on fitting 5.
Insert snap ring 2 into groove 4.
Check that seal 6 is correctly inserted on
the flow sensor.
Insert device 1 into the fitting.
If the mounting is correctly done the device
cannot be turned around anymore.
Hand lock the assembly with nut 3.
Fig. 7: Installation of the 8025 on the S020 fitting
English
18
Installation
Type 8025/8035 /
7.2.3. Installation of the SE35 electronic
module onto the S030 sensor-fitting
1
2
3
Respect the installation
instructions contained
in the operating instruc-
tions of the fitting used.
Insert the electronic
module 2 into the S030
sensor-fitting.
Fix with a 30° rotation.
Tighten the side screw
3 to lock the elec-
tronic module to the
sensor-fitting.
Fig. 8: Installation of the SE35 onto the S030 sensor-fitting
7.3. Installation of a panel version of
the 8025 flowmeter
Install the panel version of the device in a cabinet with
a protection class at least IP54 to ensure a degree of
pollution 2 inside the cabinet.
To cut the opening in the cabinet door, use the supplied cutting
plan of the frontage of the electrical cabinet, respecting the
dimensions indicated in "Fig. 9".
95
80
76
50
95
80
76
50
Fig. 9: Dimensions [mm] of the electrical cabinet frontage cutting
plan
English
19
Installation
Type 8025/8035 /
Seal
Nut
Washer
Screw
Cable clip
Fig. 10: Installation of a panel version of the 8025
Insert the 4 screws in the housing (from the front). Use the 4
supplied M4*25 screws if the cabinet door is too thick.
Insert the seal on the external threads of the 4 screws (rear of
the housing).
Put the assembly on the cutout, electronics turned to the inside
of the cabinet.
Put the 4 washers on the 4 screws.
Put a nut on each of the 4 screws and tighten the nuts to secure
the device to the cabinet.
Wire according to the instructions in chapter "8".
7.4. Installation of a wall-mounted
version of the 8025 flowmeter
NOTE
Risk of material damage if the cable glands are not tightly
screwed on the housing
Before installing the wall-mounted housing on its support,
tighten the nuts of the entry item of the cables glands at a torque
of 1.5 Nm.
The flow transmitter in a wall-mounted version has 4 holes in the
bottom of the housing.
Remove the blanking strips covering the screws.
Blanking strips
ENTER
0....9
FLOW
Nut of the entry item
Loosen the 4 screws and open the cover to get access to the
holes [1].
English
20
Wiring
Type 8025/8035 /
1
1
1
1
230V
LN
230V
T 250 mA
56789 10
LN
230V
NPN SENSOR
1 PULSE INPUT
2 -
3 +
4 NC
SUPPLY
1234PE
3A/230VAC
REL1
REL2
FLOW SENSOR
FLOW SENSOR
COILNPN
CURRENT
SOURCE SINK
COIL SENSOR
1
2
3 NC
4 NC
L+
L-
PE
P-
P+
NC
L+
L-
PE
P-
P+
Iout
PULSE
OUTPUT
Without
With
Relays
Supply
12..36Vdc
106 mm
106 mm
Fig. 11: Installation of a wall-mounted version
Secure the housing to the support respecting the dimensions
indicated in "Fig. 11".
Wire acc. to instructions in chap. "8".
Close the housing and tighten the 4 screws of the cover.
8. WIRING
DANGER
Risk of injury due to electrical voltage.
Shut down the electrical power source of all the conductors and
isolate it before carrying out work on the system.
Observe all applicable accident protection and safety regula-
tions for electrical equipment.
Insert the supplied stopper gaskets into the unused cable
glands of a compact or a wall-mounted version to ensure
the tightness of the device.
Only move the selectors when the power supply is off.
English
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174

Burkert 8025 Series Guide de démarrage rapide

Taper
Guide de démarrage rapide
Ce manuel convient également à