Polaris ALPHA™ iQ+ Le manuel du propriétaire

ENGLISH

|

FRANÇAIS

|

ESPAÑOL

H0655800_REVC

Owner's Manual

Alpha

™

iQ+

Alpha iQ

VRX

™

iQ+

VRX iQ

TYPE EC27---

WARNING

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product must be

serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed

where such state or local requirements exist. In the event no such state or local requirement exists, the maintainer must be a

professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual

can be followed exactly. Improper installation and/or operation may void the warranty.

FCC Statement

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by by the part responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This device complies with FCC and IC RF radiation exposure limits set forth for general population. This device must be

installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,

the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

THANK YOU FOR PURCHASING THE POLARIS CLEANER.

YOUR POLARIS ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY

INSTALLED AND TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW

POLARIS CLEANER, PLEASE DO THE FOLLOWING:

1) Complete and return the warranty card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please visit

www.polarispool.com to locate an independent service company near you. If you are unable to locate a service

company, please call our Technical Support department at 1-800-822-7933.

RECORD YOUR POLARIS CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot- head)

City State/Province Zip/Postal Code

Table of Contents

1 Important Safety Instructions .................. 4

2 Cleaner Specications ............................. 5

General Specications.................................................. 5

3 Assembly ....................................................6

Contents ....................................................................... 6

Assemble the Transport Caddy .................................... 6

Attach the Control Box to the Caddy ............................ 8

Connect to a Power Source.......................................... 8

4

General Cleaner Operation ...................... 9

Install and Submerge the Cleaner .............................. 10

Using the Control Box..................................................11

Start / Stop Cleaning and Adjust Cleaning Time......... 12

Lift System .................................................................. 12

5

Installing iAquaLink

™

............................. 13

Download the App ...................................................... 13

Sign Up and Log In ..................................................... 13

Congure the System ................................................. 13

6

iAquaLink

™

Control ................................. 14

iAquaLink™ Control Home Screen............................. 14

Start / Stop Cleaning and Adjust Cleaning Time......... 14

Set Cleaning Mode ..................................................... 14

Remote Control .......................................................... 14

Spot Clean .................................................................. 15

Program or Cancel Cleaning Schedules .................... 15

Temperature Display................................................... 15

LED Lights .................................................................. 16

In-App Error Messages and Troubleshooting ............. 16

System Settings.......................................................... 16

7 Maintenance .............................................16

Cord Tangling ............................................................. 16

Clean the Filter Canister ............................................. 17

Store the Cleaner When Not in Use ........................... 18

Replacing Wear Parts ................................................. 19

Replacing Tires ........................................................... 20

Spare Parts................................................................. 21

8 Troubleshooting ...................................... 22

Error Codes ................................................................ 22

General Troubleshooting ............................................ 23

Dismissing an Error Code........................................... 24

iAquaLink

™

Troubleshooting ....................................... 25

Page 4

English

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI

receptacle should be provided by a qualied installer and should be tested on a routine basis.

To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.

Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If

the GFCI interrupts power to the pump without the test button being pushed, a ground current

is owing, indicating the possibility of an electric shock. Do not use this product. Disconnect the

cleaner and have the problem corrected by a qualied service representative before using.

• Per the United States National Electrical Code

®

(NEC

®

), keep the control box at least ve (5) feet

from the edge of the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC) requires

a minimum distance of 3m (10 ft.) to be maintained between the pool edge and the control box.

Never submerge the control box.

• Do not enter pool while the Polaris cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge

trimmers and other equipment.

• To reduce the risk of electrical shock, do not use the Polaris robotic cleaner or control box if the

cord is worn or damaged. Contact Zodiac Pool Systems LLC. Technical Support immediately for

proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical

replacement parts when servicing. Do not attempt repair of the Polaris robotic cleaner, control

box, power cord, or oating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY;

PROVIDE A PROPERLY LOCATED GFCI RECEPTACLE. THE CONTROL BOX SHOULD

BE PLUGGED INTO THE GFCI RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as

part of your pool’s operational system.

1 Important Safety Instructions

Congratulations on purchasing this Polaris Robotic Cleaner. Please read through the entire

manual before installing your new robotic pool cleaner. Your cleaner must be installed and

operated as specied.

READ AND FOLLOW ALL INSTRUCTIONS

Page 5

English

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal injury.

• The Polaris cleaner must be installed and operated as specied.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A

permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily

disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled

for storage and reassembled to its original integrity.

• Clean the lter canister in the Polaris cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

USE OF THE POLARIS ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by

objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine

dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded

simply by rubbing the surface with a pool brush. Ink from the pattern can also rub o during the installation

process or when it comes into contact with objects in the pool. Zodiac Pool Systems LLC is not responsible

for, and the Limited Warranty does not cover, pattern removal, abrasion or markings on vinyl liners.

SAVE THESE INSTRUCTIONS

2 Cleaner Specications

General Specications

The general specications for the cleaner are as follows:

Control box

supply voltage

100-125 VAC, 60 Hz

Supply voltage

30 V DC

Installed load

150 W max

Cable length

60ft (18M) or 70ft (21M) depending on model

Cleaner size

(WxDxH)

16.9 x 18.9 x 10.6 in. (

43 x 48 x 27 cm)

Weight of Cleaner

21 lbs. (9.5 kg)

Packed weight

42 lbs. (19 kg)

Filtration

All-purpose lter canister

Cycle lengths

Variable programming

The cleaner is a double-insulated product. A double-insulated electrical appliance is one which has been

designed in such a way that it does not require a safety connection to ground. The basic requirement for

double-insulation is that no single failure can result in dangerous voltage becoming exposed so that it might

cause an electric shock and that this is achieved without relying on an earthed (grounded) metal casing.

This is achieved by having two (2) layers of insulating material surrounding live parts or by using reinforced

insulation. Therefore, devices having double-insulated construction, such as this cleaner, do not use a

grounded (three-prong) cord/plug.

Page 6

English

Assemble the Transport Caddy

1. Unscrew the handnut from the base

(Figure 2).

Figure 2. Remove Handnut from Base Unit

2. Insert the metal handle frame tubing into the

base with notch end at the top, then rotate so

the bends are away from you. (Figure 3).

3. Push base down (Figure 3) so the metal

handle frame is seated in the recess on the

underside of the base.

Figure 3. Connect Metal Frame to Base Unit

3 Assembly

Contents

The packaging should contain the following items:

• Polaris cleaner and oating cable

• Control unit

• Transport and storage caddy assembly

components (Figure 1)

a. handle frame

b. support blocks (x 2)

c. wheels (x 2)

d. wheel locking clips (x 2)

e. wheel axle / hubcap (x 2)

f. base unit

g. cleaner hook

h. caddy handle

Figure 1. Transport Caddy Assembly Components

x 2

A

B

C

D

x 2

E

x 2

F

G

H

When unpacking the cleaner and its components:

• Make sure each component is in the box.

• Check cleaner and components for damage

during transport.

• If there are any missing parts or damage,

contact Technical Support at 1-800-822-7933.

Page 7

English

4. Slide the handnut over the tube and twist to

tighten onto base unit (Figure 4).

Figure 4. Twist Handnut to Secure Frame

5. Snap two support blocks into place

(Figure 5).

6. Slide axle and hubcap piece through center

of wheel and attach to base unit. Snap

locking clip into place to secure wheel.

Repeat to attach both wheels (Figure 5).

Figure 5. Snap in Support Blocks and Attach

Wheels

7. Slide the control box base / caddy handle

attachment down over the metal tubing

until it snaps into place (Figure 6).

Figure 6. Attach Caddy Handle

8. Align cleaner hook pins with the top holes

in the handle tube and snap into place

(Figure 7).

Figure 7. Snap Cleaner Hook into Place

Page 8

English

Attach the Control Box to the Caddy

1. Align the bottom of the control box with the

notch at bottom of the control box hook on

the caddy (Figure 8).

Figure 8. Align Control Box with Caddy Hook

2. Press control box onto the caddy hook until

it snaps and locks into position (Figure 9).

Figure 9. Attach the Control Box onto Caddy

Connect to a Power Source

WARNING

Failure to comply with the following warnings

can result in permanent injury, electrocution or

drowning.

PREVENT ELECTRICAL SHOCK

• U.S.: Per NEC

®

requirements, keep the control

box at least ve (5) ft. (1.5 m) from the edge of the

pool. CANADA: Per CEC

requirements, keep the

control box at least three (3) m (10 ft.) from the

edge of the pool.

• Only connect the control box to a receptacle

protected by a ground fault circuit interrupter

(GFCI). Contact a certied electrician if you cannot

verify that the receptacle is protected by a GFCI.

• Do not use an extension cord to connect the

control box.

• Do not allow anyone to swim while the cleaner is

in the pool.

• The control box is water-resistant, not waterproof.

In order to prevent electrocution, never submerge

the control box or leave exposed to inclement

weather.

1. Unscrew the protective cap for the oating

cable from the side of the control box by

turning counter-clockwise (Figure 10).

Figure 10. Remove Protective Cap

Page 9

English

2. Grip the notched end of the oating power

cable, insert into the control box, and turn

clockwise to tighten. (Figure 11.)

3. Plug the control box directly into a GFCI

outlet. DO NOT use an extension cord.

Figure 11. Connect Floating Cable

NOTE: To avoid damaging the power cable, do not

try to twist the entire cable housing (see below).

X

NOTE: To avoid exposing the power cable

connector pins to water, be sure the connector is

screwed in all the way and there is no gap. (see

below).

X

4

General Cleaner

Operation

CAUTION

To prevent damage to the cleaner, be sure to

adhere to the following guidelines:

• Remove the cleaner from the pool after the

cleaning cycle is completed.

• Store on the caddy out of direct sunlight or

inclement weather.

• Never lift the cleaner out of the pool by the

oating cable. Always use the lift feature to

remove cleaner from the pool.

• Take additional care when lifting the cleaner out

of the pool. It becomes heavier when lled with

water.

• Always remove the cleaner from pool when super

chlorinating or adding acid.

• Do not handle cleaner while it is in operation.

IMPORTANT

• Always make sure the cleaner head is fully

submerged before you begin operation.

• Clean the lter canister after each cleaning

cycle.

• Do not leave your cleaner in the pool on a

permanent basis.

• At the end of each cycle, remove the cleaner

from the pool.

• Start at the cleaner head and untangle any

coils in the cable before storing the cleaner.

The Polaris robotic cleaner includes a safety

feature that automatically stops the cleaner if it is

powered on but not submerged in water. For pools

equipped with a beach area, this safety feature is

programmed to drive the cleaner in reverse and

back into the pool when the impeller is out of the

water.

Page 10

English

Install and Submerge the Cleaner

1. With the control box plugged into a GFCI

outlet, spread the oating cable across the

pool deck until you reach the middle of the

pool length.

2. At the center point, submerge the cleaner in

the pool and hold in the vertical position to

release any air trapped inside. (Figure 12).

1

Figure 12. Submerge the Cleaner Vertically

NOTE: For optimal patterning and reduced tangling, the floating cable should enter the water near the middle of the pool

length. Only place enough cable in the water to reach the farthest point in the pool (see Figure 14).

Max

Floating Cable

Length

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Figure 14. Pool Entry Point for Optimal Patterning

3. Ensure the unit sinks to the bottom of the

pool and does not oat

(Figure 13).

2

Figure 13. Cleaner Sinking to the Bottom of the

Pool

4. Place only enough oating cable in the

water to reach the farthest end of your

pool from the central point. Spread out the

oating cable ensuring there are no kinks

or coils in the cable (Figure 14).

Page 11

English

Using the Control Box

The control box can be used to initiate basic cleaning features and to connect the device to home

Wi-Fi. For more information on connecting your cleaner to Wi-Fi, see section 5, Installing iAquaLink

™

.

VRX

™

iQ+ / Alpha

™

iQ+

VRX iQ / Alpha iQ

Control box receiving power

Start/Stop cleaning

Select cleaning mode:

Waterline

(45 min)

Waterline only

Quick Clean

(1h 15 min)

Floor only

SMART Cycle

(Calculate custom clean duration)

Floor, Wall, Waterline

Deep Clean

(2h 45 min)

Floor, Walls, Waterline,

High Intensity

Dirty canister indicator

Remove cleaner from the pool

+

+ / - 15 minute increments

Initiate connection and set up

iAquaLink

™

control

Bluetooth connection status:

BLINKING - searching for signal

SOLID - paired with phone

Wi-Fi connection status:

BLINKING - connected to router

SOLID - connected to the internet

Set recurring cleaning:

Every: Day, 2 Days, or 3 Days

*

*not available on all models

Page 12

English

Start / Stop Cleaning and Adjust

Cleaning Time

The factory default cleaning mode is SMART

Cycle (Floor, Wall, Waterline).

The rst use of SMART Cycle (duration: 2:30),

will automatically calculate the cleaner’s optimal

cleaning time for your pool. After the initial

SMART Cycle calculation, the optimal cleaning

time is saved for future use.

To recalculate the SMART Cycle setting, press

and hold the MODE button for 5 seconds.

Use to change cleaning surface setting.

Toggle between:

Deep Clean

(2h 45 min)

Floor, Walls, Waterline, High Intensity

SMART Cycle

(Calculate custom clean duration)

Floor, Wall, Waterline

Quick Clean

(1h 15 min)

Floor only

Waterline

(45 min)

Waterline only

*

✳ not available on all models

1. With cleaner submerged in water, press

the to begin operation. Press

again to interrupt and cancel an

in-progress cleaning cycle.

NOTE: At the beginning of each cleaning cycle, the robot

confirms your pool parameters (approximately 10

minutes). During this time, the cleaner does not

climb to the waterline.

Press +/- buttons to increase or decrease

cleaning time in 15-minute increments.

-Minimum run time is 30 minutes.

-Maximum run time is 3 hours 30 minutes.

NOTE: The control box automatically goes into standby

mode after 5 minutes and the display screen turns

off. Press any key to exit standby mode and view

remaining cycle time. Cleaner will continue to function

in standby mode.

Lift System

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be

activated at any time during or after a cleaning

cycle.

1. Press to begin the automated

procedure.

The screen displays when the

Lift System is in operation.

NOTE: To stop the procedure at any time, press and

release the button again.

2. Next, Press and HOLD to rotate the

cleaner.

3. Once the cleaner is facing the wall of your

choice for retrieval, release the button.

4. Cleaner will drive forward and up the wall it

is facing. It will wait at the water line to be

retrieved.

5. When in reach, remove the cleaner from

the pool using the handle. The cleaner

will quickly expel water to allow for lighter,

easier removal.

NOTE: Never lift the cleaner out of the pool by the floating

cable.

Page 13

English

5

Installing

iAquaLink

™

The iAquaLink app is available for download from

the App Store or Google Play.

With iAquaLink Control, you can connect to your

robotic cleaner from anywhere, anytime to access

many functions and troubleshooting advice. App

features are dependant on model.

Before you begin installation, make sure

you have the following:

• Robotic Cleaner submerged in the pool.

• Control Box connected and plugged into a

GFCI outlet.

• Smart device (phone or tablet) with Wi-Fi

and Bluetooth enabled

• Wi-Fi router with sucent signal strength

at the Control Box

• IMPORTANT: Have your Wi-Fi network

password available.

Download the App

Install or update the iAquaLink app from the App

Store or Google Play.

Once the download is complete, select the

iAquaLink icon on your smart device to open the

app.

Sign Up and Log In

Click Sign Up to create a new user account. Or, if

you previously set up an iAquaLink account, click

Log In to access your systems.

Complete all required elds in the Account Set Up

page and agree to the Terms and Conditions.

Congure the System

1. On the My Systems page, click + in the

upper right-hand corner to add a system.

2. Choose "Robotic Cleaner" from the list and

choose your model type.

3. On the Control Box, press

Bluetooth light

indicates status:

BLINKING - searching for signal

SOLID - paired with phone

4. Follow on-screen prompts to add your

cleaner and connect to your home router.

Wi-Fi light indicates status:

BLINKING - conected to router

SOLID - connected to the internet

NOTE: The searching screen may take a few minutes to

find your router. If you receive an error you may

have a weak router signal at the location of your

control box OR you may have entered an incorrect

Wi-Fi password. In the case of a weak router signal,

consider installing a Wi-Fi extender to boost your

signal strength. (See iAquaLink Troubleshooting

section.)

Page 14

English

6

iAquaLink

™

Control

Once you have downloaded the iAquaLink

app and connected the device to Wi-Fi, the

iAquaLink app allows for robotic cleaner control

from anywhere, anytime. Functions vary within

the iAqualink app depending on which cleaner

model you have.

WARNING

Do not enter pool while the robotic cleaner

is in water.

iAquaLink™ Control Home Screen

App function and design is subject to change.

Start/Stop Cleaning

Remote

Clean Mode

Lift System

Dirty Canister Indicator

+

_

+

_

Manual Time Adjustment

(current run time +/- 15 minutes)

Water Temperature

Display

°C / F

Start / Stop Cleaning and Adjust

Cleaning Time

The factory default cleaning surface setting is

SMART Cycle (Floor, Wall, Waterline).

SMART Cycle calculates a customized cleaning

time optimized for your pool. On the rst run

of SMART Cycle, the app counts up as it

calculates the optimized cleaning time.

On periodic SMART Cycle cleaning, the app will

count down from the optimized cleaning time.

NOTE: To Recaculate SMART Cycle, go to the Set

Cleaning Mode after the initial calculation.

1. From the Home screen or the Control Box,

press the Start button to begin

cleaning.

2. The app displays the cycle time in hours

and minutes.

To increase or decrease the cycle time

during cleaning,

press the (+) and (–) buttons.

-Time adjusts up or down in 15 minute

increments.

-Minimum run time is 30 minutes.

-Maximum run time is 3 hours 30 minutes.

-The control box displays the same countdown

and cycle setting as the app.

3. Press to interrupt and cancel an in-

progress cleaning cycle.

NOTE: At the beginning of each cleaning cycle, the robot

confirms your pool parameters (approximately 10

minutes). During this time, the cleaner does not

climb to the waterline.

Set Cleaning Mode

1. From the main screen, select Cleaning

Mode to view options.

2. Choose from available cleaning modes

depending on your cleaner model.

3. In Custom mode (if applicable), select the

cleaning surface and cleaning intensity

from the on-screen icons.

✳ not available on all models

Remote Control

Use your mobile device as a remote control.

IMPORTANT: Only use Remote Control when in view of the

cleaner.

1. From the main screen, select the Remote

tab.

NOTE: When in remote control mode, the control box

displays .

*

Page 15

English

2. You can direct the cleaner using the remote

control or use the spot clean feature (not

available on all models) to help pick up

debris.

3. To use "Spot Clean" drive the cleaner near

where debris has collected and initiate "Spot

Clean." The Cleaner will perform a short

cleaning pattern to remove debris in that

area.

✳ not available on all models

NOTE: If you experience significant delays between the

app command and cleaner response, you may

have a weak Wi-Fi signal or other connectivity

challenges that interfere with the immediacy of

the remote control functions.

Lift System

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be activated

at any time during or after a cleaning cycle.

IMPORTANT: Only use Lift System when in view of the cleaner.

1. From the main screen, select Lift

System to enter automated procedure.

2. Use the left and right arrow icons to rotate

the cleaner to face the wall of your choice.

3. Press the Lift System icon to drive the

cleaner up the wall it is facing. The cleaner

will wait at the water line to be retrieved.

NOTE: To stop the procedure at any time, press and release

the button again.

4. When in reach, grab the cleaner handle and

begin to pull cleaner out of the water. The

cleaner will quickly expel water to allow for

lighter, easier removal.

NOTE: Never lift the cleaner out of the pool by the floating

cable.

Program or Cancel Cleaning

Schedules

(not available on all models)

It is still recommended to remove and clean the

lter canister after every cleaning cycle.

1. Tap the area titled Next Cleaning or

go to System Settings and choose

Schedules.

2. To program a schedule, select the day of

the week.

3. Select a start time to begin the cleaning

cycle.

4. Select a cleaning mode. Mode selected will

determine runtime.

5. Press OK to save the schedule or Delete to

remove permanently.

6. Repeat steps 2-4 to program additional

days.

NOTE: Only one programmed cleaning cycle can be

scheduled per day.

7. Press BACK or DONE to leave the Edit

Schedule page and return to the main

screen.

8. The next scheduled cleaning cycle will

display near the top of the main screen.

Temperature Display

(not available on all models)

On some models, the pool water temperature will

be displayed on the main app screen. Accurate

temperature may take a few minutes to display as

the sensor acclimates to the surrounding water

temperature. Temperature will only be displayed

during an in-progress cleaning cycle.

LED Lights

1. Sensor Nav System™ - Indicator Light:

Located on the front of the cleaner, this light

has several functions to indicate status:

Blinking Blue - Sensing, Scanning and Cleaning

Solid Blue - Cleaning

Blinking Green: Lift System or Spot Cleaning

*

Page 16

English

Solid Green: Remote Control

2. On some models, an LED light illuminates

the interior area of the body and canister.

✳ not available on all models

NOTE: LED lights may be difficult to see in sunlight.

In-App Error Messages and

Troubleshooting

If an error occurs, the status bar will show a

warning symbol and: "Cleaning Interrupted".

1. Click on the warning symbol to view

troubleshooting advice

on how to x the issue.

2. Choose Clear Error if you believe you have

xed the problem and want to re-try. Choose

OK if you want to suspend the cleaner in

error mode and work on the troubleshooting

x at a later time.

System Settings

Access System Settings by pressing the gear

icon in the upper right hand corner of the app

screen.

7 Maintenance

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death,

disconnect (unplug) the cleaner from the power

source before performing any cleaning and

maintenance.

Cord Tangling

Tangling can occur more frequently when the

cleaner is not attended to after each cleaning cycle.

The tangle-reducing swivel, in addition to proper

installation, general maintenance and the following

troubleshooting steps can help to avoid cable

challenges.

IMPORTANT

Cleaner power cable may become tangled if

correct procedure is not followed after each

cleaning cycle.

NOTE: For optimal patterning and reduced tangling, the

floating cable should enter the water near the middle

of the pool length (Figure 15). Only place enough

cable in the water to reach the farthest point in the

pool.

Max

Floating Cable

Length

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Figure 15. Optimal Entry Point in Pool

If tangling occurs, follow these steps:

1. Remove the cleaner from the pool using

the Lift System. When the cleaner is within

arm's reach, use the handle to remove from

the water. Never lift the cleaner out of the

pool by the oating cable or swivel.

2. Hold the cleaner vertically to drain

(Figure 16).

Page 17

English

Figure 16. Keep Cleaner Vertical to Drain Water

3. Unplug power to the cleaner at the control

box (Figure 17).

Figure 17. Unplug

4. Remove the cleaner from the pool and

untangle all kinks and coils in the power

cable (Figure 18). Start at the cleaner

head. Lay the cable in the sun to loosen

any tangling memory.

Figure 18. Untangle

Clean the Filter Canister

The lter canister should be cleaned at the end of

each cycle.

1. Remove the cleaner from the water using

the Lift System and let the remaining water

drain.

2. Set the unit on four wheels.

3. Push the cover lock (1) and lift the cover

(2) until it is secured in the vertical position.

(Figure 19).

2

1

Figure 19. Lift Cleaner Cover

Page 18

English

4. Remove the lter canister assembly from

the body (3), as shown in Figure 20.

3

Figure 20. Remove Filter Canister Assembly

5. Push the quick release button on the

canister assembly (4) and pull open

Figure 21.

4

5

Figure 21. Open Filter Canister Assembly

6. Separate the lter canister from the lter

support (6), as shown in Figure 22.

6

Figure 22. Remove Filter Canister

7. Empty all debris from the lter canister,

then rinse the canister, the lter support

and the cleaner using a hose, as shown in

Figure 23.

Figure 23. Wash Filter Canister

NOTE: Periodically, remove the filter canister and clean

thoroughly with soapy water

and a soft bristle brush.

Store the Cleaner When Not in Use

The cleaner should be cleaned regularly using

slightly soapy clean water. Do not use solvents

such as trichlorethylene or its equivalent. Rinse

the cleaner generously using clean water. Do not

let your cleaner dry in direct sunlight near the pool.

The cleaner should be stored on its caddy so that it

dries quickly.

1. Disconnect cleaner from the power source.

2. Starting at the cleaner head, remove all

coils and tangles from the cable (Figure

24). Lay the cable in the sun to loosen any

tangling memory.

3. Place the rear wheels on the caddy and

position the cleaner vertically on the caddy

base.

4. Disconnect the cable from the control box.

Replace the protective cap on the control

box.

Page 19

English

Figure 24. Untangle the Floating cable

5. Loosely coil the power cable starting at the

cleaner and moving toward the connection

point at control box. Store the cable by

wrapping it around the hook located on the

front of the caddy.

Replacing Wear Parts

Replacing Brushes

The cleaner is tted with PVC brushes with a

''wear'' indicator. (Figure 25).

raised groove becomes

partially flattened,

indicating excessive

wear

Figure 25. Worn Brush Indicator

To maintain cleaner performance at its best you

need to replace the brushes as soon as one of the

wear indicators is reached (even if the blade wear

is not even). It is recommended that you replace

the brushes when the rubber is worn down to

the top of the wear indicator (or every two years,

whichever comes rst).

To replace a worn brush:

1. Lift the cleaner to a vertical position so that

the handle is up (Figure 26).

1

Figure 26. Cleaner in Upright Position

2. Separate the edges of the brush and undo

the tabs (Figure 27). Remove the worn

brushes.

2

Figure 27. Undo the Tabs of the Brush

3. To install the new brush, position the new

brush on the roller with the cleaning blades

facing away from the roller (Figure 28).

3

Figure 28. Install the New Brush

Page 20

English

4. Thread each tab into the slot provided and

gently feed it through until the heel comes

out at the other side of the slot (Figure 29).

4

Figure 29. Pull Tabs Through Each Slot

5. Use a pair of scissors to cut the tabs 3/4

inch from the heel so that they are no higher

than the cleaning blade (Figure 30).

6. Repeat the procedure to install the second

brush.

Figure 30. Cut Tabs

Replacing Tires

1. Pull on the inside of the old tire to remove

the tire lip from the wheel

(Figure 31).

1

Figure 31. Pull the Old Tire Over the Wheel

2. Remove the old tire (Figure 32).

2

Figure 32. Remove the Old Tire

3. To replace the tire, position the tire on the

wheel making sure to orient the tire so that

the word INSIDE is toward the body of the

cleaner (Figure 33).

Figure 33. Tire Replacement Orientation

1

I

N

S

I

D

E

Towards

Body

I

N

S

I

D

E

I

N

S

I

D

E

La page charge ...

Polaris ALPHA™ iQ+ Le manuel du propriétaire

Ce manuel convient également à

Polaris ALPHA™ iQ+ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents